Which fog lights for the VAZ-2110 are better: Bosch or Kirzhach

Considering that the head light on the VAZ 2110 and other popular models (for example, VAZ 2114, 2115, etc.) is not the best, driving without fog lights in poor visibility conditions is quite difficult, tiring and even dangerous.

Of course, if the car does not have PTF from the very beginning, that is, in the factory configuration, in such a case, many drivers install fog lights on the VAZ 2110 themselves.

In this case, the main problems are considered to be the need to select fog lights for the VAZ 2110, as well as to figure out how to connect the fog lights. Next, we will look at what to look for when choosing a VAZ PTF, as well as which PTF 2110 will be the best solution.

Features of the VAZ 2110

The VAZ 2110 car is not very different from its younger brothers of the following modifications, but there are still some differences:

1. This model does not have front fog lights. Moreover, the car bumper may not even have seats for PTF.
2. For some reason, the car has rear fog lights, which seems strange: there are rear ones, but no front ones.
3. The VAZ 2110 can be equipped with different types of panels: standard (also called old) and europanel. In the first case, there is no space for installing the PTF power button, but there are several slots for installing additional switches. In the case of the Europanel, the PTF button can be installed in a place previously provided for this, and the fuse panel has sockets for connecting fog lights.

What you need to have to connect

1) A ready-made set of fog lights ( GKPTF ), the price of the set is about 120 hryvnia (if you don’t take fancy ones).

Set of fog lights.

Important: for an old-style torpedo you need a GKPTF kit for 2110, if you have a EURO torpedo, buy a GKPTF for 2115 (there is a difference in the buttons).

2) Indicator lamp (control).

3) Multimeter (special multitester).

4) Set of female-male connectors + 8 female connectors.

5) A roll of electrical tape.

6) Heat shrinkage (packaging).

• Electronic connection diagrams are included with the fog lights.

Legal requirements

When purchasing headlights, an auto parts store offers a huge variety of fog components in different formats and sizes. GOST 8769-75 forces VAZ-2110 drivers to control themselves and install headlights that meet certain legal requirements:

1. You cannot install just one fog light; fixation involves installing a kit consisting of 2 parts.
2. If you measure the distance from the side marker, the headlight is in 400 mm increments, and the measurements are taken along the outside of the diffuser.
3. The step from the road surface to the bottom edge to the dissipative product cannot be less than 150 mm.
4. It is not permissible to install headlights higher than the headlight.

Tools and materials required for installation

To install the PTF, you must purchase in advance the entire set of materials and tools:

1. A set of fog lights, note that the VAZ-2110 dashboard is an older model, so the headlights for Euro models should be put aside.
2. Lamp for monitoring the procedure.
3. A multimeter that allows you to test the correctness of individual stages of work.
4. Double connectors, among experts they are also called “mother and father”, 1 set is enough.
5. 8 pieces of female connectors.
6. Insulating tape.
7. Packaging material for heat shrinking.

To correctly install fog lights on a VAZ-2110, you need to start from the electrical diagram; it can be taken from KGPTF.

Russian GOST

Currently, GOST 8769-75 regulates the installation and operation of external lighting devices on vehicles operated on public roads.

The photo shows the GOST section on the requirements for installing PTF

According to section 2.3 of the designated GOST, PTF can:

1. installed on a passenger car only in pairs;
2. placed no higher than the headlights, and no lower than 25 cm from the road surface;
3. do not protrude beyond the dimensions of the car, and at the same time, be located no further than 40 cm from the dimensions of the front wings;
4. shine the same light for each headlight.

Since foreign-made vehicles are used in the Russian Federation and CIS countries, the lighting devices installed on them are subject to UNECE requirements. Which fog lights are better for the VAZ 2110:. We find out which PTFs are best suited for the VAZ 2114. Accordingly, the products of foreign manufacturers, namely PTF kits for installation on the VAZ 2110, must meet the specified requirements.

Preparing for installation

Before you go to a car store, you should find out what exactly you need to purchase, taking into account the characteristics of your car.

And for this we visually define:

1. What type of dashboard is installed in the cabin;
2. Are there any seats (stampings) in the front bumper for installing PTF?

Note! Ready-made foglight kits have a lot of differences in the mounting method. In particular, the button for turning on the fog lights of the VAZ 2110 for cars with an old dashboard has a different shape than with a Euro-dashboard.

The kit for connecting fog lights of the VAZ 2110 has a double button for the Euro panel

What's the result?

As you can see, with all the variety of optics on the market, the decision to choose fog lights 2110 may turn out to be more difficult than it initially seems. In other words, it is necessary to choose fog lights for the “ten”, taking into account all the pros and cons of the solutions presented for sale.

You need to pay attention to the housing and reflector, type of lamp, quality of wiring, equipment, reliability of PTF fastening, etc. You should also take into account the possibility of flexible adjustment.

It is for these reasons that most car owners prefer standard solutions that are installed on the car at the factory, but are not available in a specific configuration.

As a rule, the car already has standard places for installation, some wiring may be present, original buttons for on/off, the PTFs themselves, lamps, etc. are available for sale. In turn, this greatly simplifies the selection, installation and connection of fog lights.

Selecting PTF for VAZ 2114 and 2115: how to choose VAZ fog lights (housing, type of lamp, standard or universal, etc.). Installation of fog lights VAZ 2114, 2115.

How to connect PTF in a car yourself: do-it-yourself fog light connection diagram. Subtleties and nuances, what to pay attention to when connecting.

Heated windshield: advantages and disadvantages of a heated windshield. How to install a heated windshield with your own hands, recommendations.

Why do you need to adjust your car headlights and periodically check the quality of the adjustment? How to adjust the headlights yourself, headlight adjustment diagram.

How to replace light bulbs in the headlights of a Lada Kalina: replacing low and high beam bulbs. How to change the dimensions on a Kalina, turn signals, headlight glass and headlight.

Connecting the trailer socket (towbar socket): pinout, 7-pin socket. How to connect a trailer socket, what to consider when connecting. Recommendations.

Color meaning

Some people, in the old fashioned way, believe that it is better when the fog glass is yellow. But this is not true. Most leading manufacturers today produce transparent white fog lights, and they are not only as good as yellow ones, but often superior to them.

On the VAZ 2110 you can install corrugated or transparent glass. The latter are for some reason more fashionable, although less useful, since they shine in spots, while the corrugated ones give a more directed beam, which really increases visibility in bad weather.

Buying what you need

You can, in principle, buy a ready-made set along with wires, but many believe that if you buy everything separately, the number of installation options increases, and it will all cost less. So, we buy:

• Set of headlights (2 pieces);
• Plastic pads;
• Headlight frames;
• A key and a yellow indicator for it;
• Relay;
• Wires. It is better to purchase ones from an electrical equipment store, so that there are two copper conductors with double insulation (ShVVP-2 is suitable). A cross section of 0.5 mm will also be normal, but if you want to install lamps of higher power, take 0.75 mm;
• Terminal for installation to ground;
• Wide as well as narrow terminals, called mother/father. When purchasing them, it is advisable not to take them complete with wires. Installation will be more convenient if these terminals are crimped with pliers already on the connections of the installed wires.

Kit for connecting fog lights on VAZ 2110

Note: if your VAZ has an old-style dashboard, then it is better to buy a PTF 2110 kit, but for a new, so-called EURO, it is more convenient to connect PTF 2115.

You can, of course, vary it, but we are talking specifically about the convenience of the location of the buttons. Regarding the power of the lamps, 55 W is enough, no more is needed. Also keep in mind that very cheap fog lights will not last long.

Selection of fog lights for the VAZ 2110

The range of PTFs for the VAZ 2110 today is quite wide: large and small, round and square, yellow and white. Which ones to choose? Everything here will depend on your taste and financial capabilities, but I still dare to give some advice.

1. Yellow light is less absorbed by water (and fog and rain are water). This means that yellow PTFs will produce a higher quality light spot than white ones of the same power, and at the same time they will not dazzle oncoming drivers.
2. The shape of the headlights does not matter, the main thing is that they should fit the seats of your bumper as best as possible.
3. You should not buy very expensive headlights from famous brands. Most often, such companies charge a lot of money just for the fact that they are famous (the so-called surcharge for the brand).
4. Before purchasing, take the headlight in your hands and carefully examine the quality of the body and glass. Even by its weight and appearance, you can feel whether it is a worthwhile thing or junk that will fall apart after 100 km of run.

Below I will give some common and affordable PTF models for the VAZ 2110 that really deserve attention.

Features of PTF: difference from headlights

So, the main task of fog lights is to illuminate the road in poor visibility conditions (rain, snow, fog, etc.). However, unlike the head light, there are features.

First of all, PTFs must have the clearest possible upper cut-off line, and the beam of light must be strictly below and be as wide as possible. If these conditions are not met, this can become a problem both for the driver of the vehicle and for other road users driving in the oncoming lane.

We also note that even if the headlights have the most powerful lamp, the features, purpose and installation location of such headlights do not allow them to effectively illuminate the road in fog or rain.

The fact is that the head light should illuminate the road as far as possible, not blind oncoming drivers and cover the side of the road. However, in conditions of limited visibility, neither high nor low beam can cope with this task. The reason is that a powerful luminous flux is reflected from moisture particles, causing a cloudy “wall” to appear in front of the driver. This is especially noticeable when the high beams are turned on.

In turn, high-quality PTFs are characterized by lower power, and the optics themselves are made and installed so that the light from the fogs literally “breaks through” moisture and fog. The main secret is that usually the fog does not touch the ground, and the fog lights are as low as possible. On the one hand, fog lights do not shine as brightly and far as the headlights, but in poor visibility conditions they illuminate several meters of the road in front of the car. The main thing is to follow the rules for installing PTF and setting up such optics.

• In a nutshell, there are clear norms and standards that must be adhered to during installation. Additional adjustments allow you to set the fog lights so that the light flux falls on the road, does not blind the driver, does not form a “wall” in the fog in front of the car, etc.

At the same time, it is important to understand that cheap and low-quality PTFs, as well as incorrectly installed fog lights of a VAZ or any other car, will blind oncoming cars, but are not able to fully illuminate the road. For this reason, when selecting fogs, first of all, you need to pay special attention to this optics.

Installation process

Before installing fog lights on a VAZ 2110, you should carefully consider purchasing them.

But don’t rush to the store, but first figure out what kind of front bumper your car is equipped with. If the bumper has seats for PTF (they are usually closed with plugs), then everything is in order. Measure your seats and go to the store.

If the installation of fog lights on your bumper is not provided, then you will either have to buy a new bumper or do it yourself. Here everything will depend on your desires and capabilities, since there are always PTFs on sale with decorative overlays that can be installed on almost any bumper.

This can be done using a conventional drill by drilling a series of holes around the perimeter of the future seats.

After the hole is cut or the plugs are removed, install the PTFs in their places, following the instructions and using the fasteners included with the headlights. Typically, headlights are attached through a decorative trim using two screws.

Why are fog lights needed?

The very name “fog” lights already speaks about their essence.
Their light penetrates fog, a wall of rain, and contributes to more efficient illumination of the road. The presence of PTF provides three important advantages.

1. PTF or fog lights are characterized by a flatter luminous flux, which literally spreads above the ground, spreading more in width than in height. This was done on purpose, since the temperature of the road surface is higher than the temperature of the air and fog, so it does not fall to the ground itself. Consequently, fog lights provide a certain range of illumination compared to conventional headlights. You will see approximately 10 meters further than with low beam.
2. The width of the PTF light beam allows you to see the markings and the side of the road, which will allow you to make a maneuver in time and not end up outside the road surface. Unfortunately, this is a common occurrence in foggy conditions. Moreover, those who do not have fog lights suffer much more often. It is a fact.
3. PTF does not blind oncoming cars, but allows them to see you. Only if the headlights are adjusted correctly, of course. Therefore, fog lights on your car have a big impact on safety by signaling oncoming cars that you are approaching.

Correct installation and connection of fog lights VAZ 2110 and its modifications

Not all models of the tenth row of VAZ are equipped with factory fog lights. If the driver independently tunes additional lighting, he has three options for solving this problem:

1. Buy a front bumper with fog lights already installed. They just need to be connected to the car network.
2. Buy a front bumper with ready-made stamped sockets for installing PTF. In this case, you need to choose the right set of fog lights and install them yourself.
3. Make holes in the plastic for the PTF yourself, attach the fog lights and connect them to the car’s network. This option allows an experienced driver to install fog lights from foreign cars on the VAZ 2110 model range.

The “tens” model range is equipped with PTFs with corrugated (provide a narrowly directed light flux) or transparent (gives spots of light) glass.

The requirements of the Road Traffic Regulations do not contain a mandatory condition for installing PTF on cars, so domestic manufacturers do not always install fog lights on the assembly line. But there are GOST 8769–75 and GOST 41.48–2004, which regulate the number, location and order of switching on all lighting devices, including fog lights.

Requirements for installation of PTF

Fog lights are installed according to certain rules:

• quantity - 2 pieces;
• no closer than 25 cm to the surface of the road surface;
• no more than 40 cm from the outer contour of the headlights;
• sockets for fog lights should be located below the top point of the low beam headlight socket;
• PTF line-of-sight angles should be: in the vertical plane 5o+5o, in the horizontal plane - 45o+10o.

Regular and similar PTFs

Rectangular fog lights with standard mounts fit into the VAZ-2110 bumper in a standard place without additional modifications. They are produced by a lot of manufacturers, but, again, all these headlights are different both in the quality of the optics and in the light source.

The most common are two types of domestically produced PTFs OSVAR and headlights from the Avtosvet plant from Kirzhach. The latter have two modifications - for a lamp with H3 and H1 sockets. According to user reviews, headlights with H1 lamps provide a denser and more concentrated luminous flux over the entire illumination range. Their price is about 900 rubles apiece. But they are sold without a lamp. Fog lamp Kirzhach. Domestic headlights - OSVAR 2212.3743-04. They are assembled rather roughly and this spoils the appearance. The lampshade is non-removable and is glued in with sealant, which if damaged will affect the cost of replacement. However, with a price of about 700 rubles (with a lamp), they look pretty decent. The illumination is even, but if installed correctly, the near zone is illuminated worse.

Another relatively domestic manufacturer is the Ryazan Bosch plant

The headlights are designed for H3 lamps, the light doesn’t matter, but they also cost about 650 rubles. The most budget option for infrequent use

They are sold without a lamp.

Instructions for installing and connecting fog lights on a VAZ 2110, 2111, 2112 with your own hands

For independent installation and connection, you will need plumbing skills, the ability to read and understand electrical diagrams, and a willingness to incur certain material costs.

Tools and materials

To install PTF you need to have on hand:

• multimeter (multitester);
• control light;
• a combination screwdriver with a slotted and cross-shaped working body;
• pliers;
• wire cutters;
• wrenches 8x10, 12x14;
• light hammer;
• electrical tape;
• packaging of heat-shrinkable tubes.

You can purchase a ready-made set of fog lights for the VAZ 2110 or buy everything separately (cheaper option):

• PTF - 2 pcs.;
• right and left frames made of plastic for VAZ 2110 fog lights - 2 pcs.;
• a key with a yellow backlit indicator;
• relay;
• wire with 2 copper cores of different colors with a diameter of 0.5 mm (for more powerful lamps, a diameter of 0.75 mm is preferable) - 5 m;
• narrow female connection terminals (single) - 8 pcs.;
• wide (double) female/male block for connection to each fog lamp - 2 pcs.;
• M8x45 bolts - 4 pcs.;
• “wings” for M8 bolts - 4 pcs.

Self-installation and connection

Before installing the PTF, you need to remove the plugs on the front bumper and secure the fog lights with frames. The best option: do not use self-tapping screws, but M8x45 bolts with wings, which provide more durable fastening and quick dismantling.

The fog lamp is inserted into a special frame, with which it is attached to the hole in the front bumper

Installing PTF will take a minimum of time if you follow this algorithm:

1. Connecting to the electrical network should begin by pulling the wires from under the dashboard into the engine compartment. They must first be placed in a protective corrugation.
2. The operation described above may require partial disassembly of the torpedo. On the VAZ 2112, the factory wiring provides this option for connecting the PTF, so you just need to find the connection pads, which are located near the socket plugs in the front bumper.
3. Remove the positive terminal from the battery.
4. Open the relay and fuse mounting block (located at the bottom left of the steering column near the clutch pedal).
5. Unscrew the self-tapping screw with a screwdriver and remove the block.

The mounting block with fuses is located on the left side near the driver’s left foot.
After this, you need to find the fuse terminals F4 (serves to protect the right PTF) and F14 (protects the left fog lamp).

The location and purpose of fuses in the VAZ 2110, 2111, 2112 mounting block are indicated on the inside of the protective cover

Fuse F20 provides protection for the rear PTFs, which were originally built into the rear lights of the VAZ 2110 model range in the form of side light lamps with two filaments. In unfavorable weather conditions, the second thread is activated by a special button located on the dashboard.

At the final stage, you need to put copper connectors of the “female” type on the ends of the wires and insert them into the plug according to the attached electrical and wiring diagrams.

Electrical diagram for connecting fog lights VAZ 2110, 2111 and 2112 using a backlit key and relay

The choice of location for installing the fog lamp switch depends on the type of front panel. There are certain nuances in connecting the old PTF and the European panel.

Simple do-it-yourself connection of fog lights on a VAZ 2110 and VAZ 2111 with an old front panel without connecting the PTF switching relay

On VAZ 2112 models with a Europanel, wires for connecting fog lights are installed in the car wiring at the factory.

Wiring diagram for connecting the VAZ 2112 PTF wires to the factory wiring connected to the PTF sockets, mounting block, relay and to the backlit power button (connects independently)

General algorithm for connecting and connecting fog lights

Installation of fog lights will take approximately 1–1.5 hours if you proceed in the following sequence:

1. The PTF wiring is laid on top of the main wiring, which runs along the left front fender.
2. According to the factory's recommendation, power to the PTF power button, inserted into the socket on the dashboard, should be taken from the fuse for the right side lights. With this option, the PTFs will remain on when the ignition is turned off. If you don't turn them off with your button, the battery will quickly drain. But if the PTFs are powered from the main headlights button or directly from the ignition switch, they will light up when you turn the ignition key.
3. Connect the plugs to the fog lights and turn them on. If the PTF on the VAZ 2110 and its modifications does not light up, it means that an error has crept into the wiring diagram. In this case, each element of the circuit should be checked again.

Video: connecting fog lights VAZ 2110

Making sure your fog lights are lighting correctly is relatively simple. You need to drive onto the road in the evening or at night and turn on the PTF. If the light flux is directed slightly downwards and illuminates not only the roadway, but also the side of the road, then everything has been done correctly. In this case, oncoming drivers will not be blinded by the light of your PTF and sufficient visibility is guaranteed in bad weather conditions.

How to choose, install and connect daytime running lights with your own hands

The inside of the headlights are foggy, what should I do? defogging of headlights

Video review of PTF from three manufacturers

THIS IS NOT AN ADVERTISING - AN ARTICLE ON FIGHTING PIRACY!

Hi all! I want to tell you a story from the life of my car. For a year of operating the car in harsh Ural conditions, namely: mud - salt baths in the autumn-winter period.

My PTFs could not withstand such abuse - they rusted, became sweaty, and generally stopped shining. I started thinking about replacing them.

The idea of ​​going to a car dealership and having them replaced under warranty disappeared immediately. Because they would have supplied me with exactly the same ones - BOSCH. Their quality is so-so! I read the reviews and realized that I only need KIRZHACH. I haven’t taken anyone’s word for a long time, so I started looking on the Internet for a description of the original headlights. There is actually very little information about them on the Internet. People apparently just come to the store, ask for PTF Kirzhach, the sellers give them the first ones they come across and people, taking their word for it, go home happy. I was convinced of this while crawling around the BZ here on Drive. In several BZ I saw entries about the installation of PTF Kirzhach. Yes, only in the photos of the creators of the BZ, well, it’s not Kirzhach, but a very good fake. In general, I searched and searched and then I was struck by a simply brilliant idea to go to the official website of the manufacturer and find there a photo and description of these very PTFs. I found the website www.zavod-avtosvet.ru. I went there, but there was very little information there either. A tiny photo and description are given. Here is what the manufacturer writes about these PTFs:— Fog lamp 202.3743010 was developed at the request of AvtoVAZ OJSC to replace fog lamp 20.3743010— Performs the functions of road lighting in conditions of limited visibility (fog, snow).— The headlight is officially approved in accordance with the requirements of the UNECE Rules .Installed in the car bumper. Voltage 12V. Lamp: AKG12-55-2 (H1). Has adjustable light beam tilt. Has a colorless glass diffuser.

Applicability: VAZ 2110 and modifications; VAZ 2114, 2115. Advantages of the new headlight: 1. Improved lighting characteristics.

2. Increased tightness: improved protection against dust and moisture.

3. The resistance of the diffuser to thermal changes has been increased. At first I thought that I wouldn’t get far with such information.

But still, I took a piece of paper and a pen and wrote down the following: Catalog number 202. 3743010 Lamp H1.

Having stopped at the first store, I asked to see the PTF. Everything was ok, everything matched, only they were under an H3 lamp and there was no letter K on the glass (the manufacturer’s logo). After talking with the seller, we came to the conclusion that it was a fake.

Moreover, he himself told me about this, and also gave advice that I should look more carefully and be sure to look for the letter K on the glass. We said goodbye kindly and I moved on.

I spent a long time shopping everywhere with just my own self-propelled gun. Having stopped at another large store, I asked about PTF, they let me look at it and again it was a fake, and the seller was so crazy, proving to me that it was them, that he himself believed in his words. Well, in general, I drove, I drove, I searched and searched, there was just excrement everywhere.

Today, for good luck, I decided to go to AMK, they have a Lada Detail store there. I went in and looked - they were lying there - a couple. I asked to see it.

Well, finally my efforts paid off. I found the original. It’s a little expensive though, 700 per piece, but they are 100% true.

So, what should we see on the headlight? 1) on the glass 202.37432012) on the glass the letter K

3) on E22 glass in a circle (middle left) 4) on H1 glass

5) four screws should be visible through the glass 6) the light diffuser should be visible through the glass

7) on the back side of the PTF on the reflector there must be engraved 2110-3743010-02 (the last digits may differ - for example - 01) 8) on the back side of the PTF on the frame 202.37439) the beam tilt regulator must be made in the form of a screw, not a SCREW!

Well, that's all. Do not buy fakes, because there is no joy in them!

Considering that the head light on the VAZ 2110 and other popular models (for example, VAZ 2114, 2115, etc.) is not the best, driving without fog lights in poor visibility conditions is quite difficult, tiring and even dangerous. Of course, if the car does not have PTF from the very beginning, that is, in the factory configuration, in such a case, many drivers install fog lights on the VAZ 2110 themselves.

In this case, the main problems are considered to be the need to select fog lights for the VAZ 2110, as well as to figure out how to connect the fog lights. Next, we will look at what to look for when choosing a VAZ PTF, as well as which PTF 2110 will be the best solution.

Connection to electrical circuit

So, the VAZ fog lights are installed in their regular places, all that remains is to connect them to the VAZ hog network. According to the current rules (see above), PTF can only be turned on together with the side lights. If you turn on the PTF, but forget to turn on the “dimensions”, then this will already be a violation.

The fact is that the fog lights are installed quite close to each other, and in the dark the oncoming driver will not be able to correctly assess the width of your car. That is why the side lights must be on when the PTF is operating.

To prevent this from happening, the connection diagram for fog lights in a VAZ is assembled in such a way that they cannot be turned on with the lights turned off. Despite its apparent complexity, the circuit is quite simple, and anyone with basic knowledge of electrical engineering can understand it.

Headlight markings

Here, in fact, we have come to the main topic of the article.

Specifically, how to find the best fog lights for the VAZ 2110, focusing on:

1. Awareness of the place of their correct installation;
2. Compliance of PTF with current requirements and standards;
3. The presence of all fastening and installation parts, as well as adapters for connection to the standard VAZ wiring connectors.

The best way to tell about the suitability of a particular set of PTFs is their marking.

Pay attention! You should look at the markings not on the cardboard packaging, but only on the glass and headlight housings. Since almost always the packaging plays the role of advertising, while the internal contents of the kit may not correspond to it.

Other manufacturers and types of lamps

Of course, many are trying to install other types of light sources and other types of lamps. All headlights discussed above have a halogen lamp. That is, it is actually the same incandescent lamp, but its filament operates in a gas environment (bromine or iodine halogens).

There are also alternative fog lights.

LED PTF

Intelligent LED PTFs are very expensive, and it makes no sense to buy cheap ones.

The main disadvantage of effective LED fog lights is their huge price and low efficiency..

The low efficiency is explained by the fact that a conventional LED produces light that is bright and pleasant to the human eye with a temperature of about 6000 K. This is not bad for head optics, but not for PTF. However, there are exceptions. For example, Osram LEDriving FOG 101 . A high-tech device with LEDs of a proprietary proprietary design with a color temperature of about 3000 K, which is just suitable for PTF.

Price - no less than 16,000 rubles.

Xenon PTF

Difficult to install and expensive lighting devices.

Standard PTFs converted to xenon fog lights.

The old xenon PTFs worked on lamps D1 and D2, the new ones received lamps D3 and D4 without the use of mercury vapor. Theoretically, the efficiency of such fog lights and the luminous intensity are higher than those of halogen lights. However, do not forget about the specificity of PTF - not to cause reflection of the beam from the water suspension. And all inexpensive xenon headlights require very precise adjustment of the light beam and are not able to provide a low horizontal stripe to combat fog.

In addition, the maximum color temperature for the effectiveness of fog lights is 3000-4500 K , otherwise they will be of no use and blinding light will be provided for oncoming drivers. The prices of such foglights are not lower than 5-7 thousand ( Hella Micro DE , for example). Anything cheaper is useless and even dangerous.