How much does a 3x5 metal garage weigh, thickness 3

On average, the weight of a 3x6 metal garage varies between 3-4.5 tons. You may only need information about how much a garage weighs in 2 cases:

You haven't yet decided which metal garage you're going to buy.

In this case, the weight of the metal garage will affect the cost of delivery and the load that the concrete base will receive. If you purchase a garage box from a specific manufacturer, then all the necessary information can be found in the delivery note.

You have decided to move your old metal garage to a new “place of residence”.

In this case, it is quite difficult to know the exact weight of a 3x6 metal garage, since many people cook it themselves. In this case, various material options are used - from various configurations of corners to metal thickness varying around the entire perimeter.

If you are faced with the 2nd situation, then using our method you will quickly calculate the approximate weight and be able to choose the right manipulator.

Approximate calculation of how much a 6 by 3 meter metal garage weighs

Initial data : length 6 meters, width 3 meters and height 2 meters. The basis of the design is an all-welded type of garage, in which a layer of sheet steel with a thickness of about 4 mm (the most common option) acts as a cladding. These are the minimum standard garage sizes for any modification of a passenger car.

Important: How much an iron garage weighs will mainly depend on the thickness of the sheet covering and the total surface area. The basis of the structure for passenger cars weighs at least 2 tons. The roof covering itself will be 1-1.5 tones. The remaining weight is provided by racks and shelves that are installed inside.

Briefly, for the calculation, do the following: Calculate the volume of the garage box by multiplying the length, thickness and height along the axial dimensions. Then, knowing the volume values of the roof and wall, you multiply the resulting figures by the specific gravity of the sheet metal. As a result, we get a weight that will differ by 5-10 kg from the real one.

Design elements

GOST standards regulate not only the length, width and height of the cabin itself. Various types of structural elements are also standard for such structures. Thus, typical window sizes are 0.8 x 0.9, 7 x 7 m or 0.8 x 1 m. Standard door sizes for single-size change houses are 1800 x 800 m. The area of rooms in such structures is 6 m2 equal to 2.25 x 2.3 mm. The vestibule in single-size ones is most often made wide at 1.5 meters. In conventional designs, this figure can be equal to 1 meter. Construction cabins with one door and no windows are quite popular.

Article on the topic: How to draw a garage project

A direct example of calculating the weight of a metal garage

We count all the elements one by one:

Area of side walls: 2*6*2 pieces = 24 sq.m.
Area of a 2-pitched roof, taking into account the small overhang of the canopies: 2 * 1.9 * 6.2 * 2 sides = 47 sq.m.
We calculate the area of the rear and end walls together with the gates: 3*2*2 pieces = 12 sq.m.
The approximate area of 2 triangular pediments is 4-4.5 sq.m.
If there is a metal floor, we also calculate its area: 3*6 = 18 sq.m.
We add up all the obtained values: 24+47+12+4+18 = 105 sq.m.

Since in the initial data we have the thickness of the walls of an iron garage within 4 mm, then according to GOST we find the specific gravity of 1 sq.m. canvases. It is equal to 31.4 kg. All that remains is to multiply the resulting mass by 1 sq.m. steel sheet for the total area. We get 105 sq.m * 31.4kg = 3297kg. As a result of calculations, we found out how much a 3mx6m iron garage weighs without taking into account the weight of the gate frame and the structure itself - only the weight of the sheathing. The frame together with the gate will weigh another 800 kg - 1 ton. As a result, the total weight will be 4-4.3 tons.

Below are the average weights of the most popular metal garage sizes:

Garage 4x6 m - weight 4.5-4.8 tons;
Garage 3x5 m - weight 3.8-4 tons;
Garage 4x5 m - weight 4.1-4.2 tons.

We hope that the calculation methodology is clear and does not require additional comments. At the end, I would like to show a video of the actual assembly of a metal garage from scratch to full commissioning.

Dear site visitors,

An online calculator has been launched on the pages of our store!

In order to calculate the weight, length, quantity, price of the rolled metal you are interested in, go to the product page. You can find the product through the right menu.

When purchasing rolled metal, the consumer is faced with the task of calculating the weight and volume of metal to select transport, calculate building structures and resolve other issues.

To determine the weight and other parameters of rolled metal, you can make an online request, call our managers or use these tables.

The tables indicate the theoretical weight of rolled metal. The actual weight may differ from the theoretical weight by ±0.2% - 3%.

Construction technology

Methods and instructions for making garage shelves with your own hands
According to the instructions, you need to assemble all the panels, securing them with the supplied components, these are brackets made of very durable metal, bolts, nuts, etc.

Before starting work, be sure to make sure that the manufacturer has packaged everything and sent it to you according to all items on the list attached to the product. Precast concrete garages are usually equipped with metal gates.

Foundation, pit/cellar construction

There is no need for a special foundation; this is permissible due to the characteristics of the material.
For the inspection pit, the prefabricated reinforced concrete garage is equipped with special reinforced concrete panels assembled according to the same type.

Since reinforced concrete structures tend to accumulate condensation, it is not worth making a cellar, as this will increase the already excessive humidity in the room.

If you nevertheless decide to make a cellar, then you should seriously consider ventilation, interior lining, which reduces the level of humidity and it is advisable to heat the rooms for drying.
If the garage does not have stable heating, then the inspection hole will also increase the humidity of the room; it is preferable to avoid creating an inspection cavity. Or use a thick awning or a special panel to cover it.

Roof

A lightweight single slab with voids in the body is used as a roof. You can sheathe and insulate it if you plan to have a heated garage. Otherwise, the lining makes no sense.

You can make a metal pitched roof superstructure to reduce the retention of precipitation on the surface, which increases condensation in the room.

Panel assembly

Install the floor slabs first, then install the side walls.
Proceed to installing the back plate connecting the right and left walls.
Attach the front gate plate.
The roof in the form of a separate slab is installed last.

If a basement is provided, then a queue is arranged first, at the very first stage.

Waterproofing

The floor and walls are completely waterproofed along the contour in the form of a strip of about 30 cm, starting from the very bottom of the walls. Waterproofing is applied by pouring concrete on the floor.

It is equally important to waterproof the ceiling using Hydrotex-U. Fiberglass is applied to more vulnerable places and where the seams of the structure lie; it is sold in the form of tape and glued to a special compound.

Insulation

Foam sheets are the most common insulation for reinforced concrete buildings.

It is glued directly to the walls using special glue.
Then the entire surface is plastered, the plaster is applied to a thick and thick layer of glue distributed over the surface of the panels.
Next, use putty.
You can stop there, or you can cover it with paint.

Watch the video about insulating a garage with foam sheets:

https://youtube.com/watch?v=gzitfWXXrk4

A flat roof is finished on the outside with roofing felt material, or in the case of a pitched roof, ondulin or corrugated sheeting is used.

If desired, the roof can be insulated from the inside in the same way as the walls.

Heating

A convector is a lightweight heating option; it will mainly affect your indoor comfort in cold weather and will serve to warm up your car in severe frosts.
Warm floors can effectively dry a room, they are safe in terms of the possibility of fire, and they can be turned on for a long time.
A radiator powered by an electric boiler is a good option that combines the advantages of the first two.

Finish options

Siding is a very aesthetic and inexpensive option.
Stone of artificial origin - such finishing, in addition to giving a beautiful look to your motorhome, will also increase the heat capacity of the room.
Finishing with plaster will have a good effect on the level of humidity in the room, significantly reducing it.
Lining is an excellent option, but very expensive. But it will create an additional bonus in terms of insulation and humidity parameters. It’s nice to be in such a room, if in addition to the garage it is also a utility block, then the lining will be optimal. It will be necessary to treat the wooden surface with solutions to prevent rotting and fire.
Chipboards are a good eco-friendly option, increasing the heat capacity significantly.

A long-living garage, easy to install, and provided the room is insulated, can surpass even brick garages in its ability to retain heat. In terms of price, the construction will cost several times less than the brick version.

Calculation formulas

Determination of the theoretical mass of one linear meter of pipe

m=?*(ds)*s*?/1000 , where

m=theoretical mass of one linear meter of pipe in kg, ?=3.14 (constant value), d=outer diameter in mm, s=wall thickness in mm, n=1000/m, ?=density in g/cm3

Determining the approximate number of linear meters of pipe in one ton

n=1000/m

Determining the approximate amount of sheet in one ton

n=10/V*?

Determination of the theoretical mass of one sheet

m=V*?/10 , where

m=theoretical weight of one sheet in kg, V=Sheet volume=thickness (mm)*, width (mm)*, length (mm), ?=density in g/cm3

Determination of the theoretical mass of one linear meter of a circle

m=x*d2*?/4000 , where

m=theoretical mass of 1 p/m of circle in kg,

x=3.14 (constant value),

d=outer diameter in mm,

p=density in g/cm3,

Density is taken in g/cubic meter. cm:

Formula for calculating the weight of 1 p/m of pipe. When you need to quickly find out how much a linear meter of a carbon steel pipe weighs, but there is no reference table, use this formula - Mp = ((Dn - Ts) / 40.5) * Ts Du - pipe diameter (mm), Ts - wall thickness ( mm), MP – weight of 1 p/m of pipe in kg.

Alternative solutions

Structures made from metal profiles have a lot of advantages, but some are not satisfied with their weight, problems with transportation when they need to move often, and some other nuances, so alternative solutions are selected. If you have to move often or go on vacation, then you can use a shell awning.

Shell awningSource bhutanmusktravels.com

Essentially, this is the same garage, but instead of sheets of metal, it uses high-strength fabric. It does not allow precipitation, wind or sunlight to pass through. In some cases, a tarpaulin is used for this, but it is better to use polyester fabric, which must be impregnated with special compounds. In addition, such an awning can be a good option for temporary housing on vacation, at the cottage, and so on.

How much does a 3x6 metal garage weigh? The answer is in the article!

On average, the weight of a 3x6 metal garage varies between 3-4.5 tons. You may only need information about how much a garage weighs in 2 cases:

You haven't yet decided which metal garage you're going to buy.

You have decided to move your old metal garage to a new “place of residence”.

If you are faced with the 2nd situation, then using our method you will quickly calculate the approximate weight and be able to choose the right manipulator.

Approximate calculation of how much a 6 by 3 meter metal garage weighs

Weight of a metal garage 3x6

Initial data: length 6 meters, width 3 meters and height 2 meters. The basis of the design is an all-welded type of garage, in which a layer of sheet steel with a thickness of about 4 mm (the most common option) acts as a cladding. These are the minimum standard garage sizes for any modification of a passenger car.

Important: How much an iron garage weighs will mainly depend on the thickness of the sheet covering and the total surface area. The basis of the structure for passenger cars weighs at least 2 tons. The roof covering itself will be 1-1.5 tones. The remaining weight is provided by racks and shelves that are installed inside.

A direct example of calculating the weight of a metal garage

We count all the elements one by one:

Area of side walls: 2*6*2 pieces = 24 sq.m.
Area of a 2-pitched roof, taking into account the small overhang of the canopies: 2 * 1.9 * 6.2 * 2 sides = 47 sq.m.
We calculate the area of the rear and end walls together with the gates: 3*2*2 pieces = 12 sq.m.
The approximate area of 2 triangular pediments is 4-4.5 sq.m.
If there is a metal floor, we also calculate its area: 3*6 = 18 sq.m.
We add up all the obtained values: 24+47+12+4+18 = 105 sq.m.

Car types

The amount of revenue from the delivery of scrap directly depends on the parameters of the lot being delivered. In relation to the recycling of rolling stock, it is necessary to know the weight of cars of different types.

A covered freight car is designed for transporting goods that require protection from atmospheric influences and open theft of products. The structure includes a roof, floor, four walls, two wheelsets, and sliding cargo doors. Such a freight car weighs about 27 tons (the weight of the wheel sets is not taken into account).
The design of the freight gondola car consists of a solid floor and four walls. The absence of a roof implies the transportation of goods that will not be damaged by precipitation. Depending on the load capacity, the car is equipped with two or four wheel pairs. The loading procedure for such a car is completely mechanized; floor hatches can be used for unloading. The gondola car weighs 23 tons.
Platforms for transporting special equipment, vehicles, technological equipment and large cargo consist of a base platform and wheel pairs. The open type design does not provide any protection for cargo. The weight of such a unit of rolling stock is 24 tons.
Hopper is one of the types of covered freight cars. It is designed to move bulk cargo that needs to be protected from external influences. Among the design features, it should be noted a floor with hatches for unloading products, inclined walls, and a roof. Weight is 24 tons.
Tanks are designed for transporting liquid, powdery cargo or gas. Determining exactly how much a railway tank weighs is not difficult, taking into account the model. For example, a tank for transporting milk weighs 23 tons, and a large container for transporting powdered goods weighs 52 tons.
A passenger carriage may have different internal structures. Rolling passenger stock intended for long-distance travel consists of separate compartments and a life support system. Depending on the manufacturer and series of the car, its weight ranges from 52 to 60 tons.
An electric train car has different weights depending on its design features. The trailed head car weighs a little more than 40 tons, the trailed intermediate car weighs 38 tons, and the intermediate motor car weighs 54 tons.

It is easy to clarify the indicators, taking into account the characteristics of the model of a particular car. In addition, the list includes specialized units of rolling stock (mail, isothermal, cars of various specializations).

Each type of rolling stock unit has its own design features, additional elements, railway linings, which in a certain way influence the weight of the lot of scrap being delivered. If the car is rented out as a whole, then the weight must be specified in the reference material, taking into account the model and manufacturer of this unit of rolling stock.

Article on the topic: Which compressor to choose for the garage

If scrap is accepted in cut form, then the total weight of the metal batch, its category and the percentage of blockage will affect the final amount.

The weight of a metal garage - what needs to be taken into account when calculating

The weight of an iron garage depends on many parameters that must be taken into account when calculating the weight of the structure.

An iron garage is an inexpensive and fairly reliable shelter for a car. It will solve many pressing problems: it will hide the car from bad weather or the hot sun, accidental damage and prying eyes; you can carry out simple car repairs, diagnostics or other preventative work in it.

Usually, few people think about the weight of a building, but sometimes a situation arises when a car owner needs to know the weight of a metal garage, so in this article we will talk about the types of metal garages and provide calculations for buildings made of different facing materials.

Types of metal garages

All-welded metal garage.

Garages that have a frame made of steel structures (see Frame garage: how to build it yourself) are considered metal, although they can be sheathed with various materials.

They are divided into two types:

All-welded structures are assembled from sheet steel and all elements are connected by welding. Such a garage cannot be disassembled and can only be transported in assembled form. An all-welded garage can be installed anywhere, it is particularly reliable against penetration and has strong connections.
Prefabricated garages have bolted or anchored connections of parts; the structure can be disassembled and transported in a compact form. It is recommended to install this type on the territory of a personal plot or in a country house, not far from the house, so that there is supervision, since it has poor protection against burglary.

A prefabricated garage made of metal plates, assembled using bolted connections.

Important! In turn, prefabricated structures can have different cladding, and this also determines how much an iron garage weighs.

The following materials are used for lining the walls of the structure:

All these materials have different weights, so when determining the weight of the garage as a whole, this must be taken into account.

How to calculate the weight of a garage

Garage made of painted corrugated sheet metal.

Data on the weight of the transported structure may be needed in the following cases:

When purchasing a garage and delivering it to a permanent location. If the building was purchased from a manufacturer, then the seller provides data on the weight of the order, but when the garage is purchased second-hand, then in this case the weight is often calculated by the buyer.
When transporting a garage to a new location (owner moving, sale, garage for demolition, etc.). If the structure was built with your own hands, the owner may not know its true weight.

For a sample, we will calculate the weight of a metal garage 3 x 6 x 2 m2 (width x length x height) of an all-welded type, in which the lining is sheet steel 4 mm thick. This is the minimum standard size into which almost any passenger car will fit, well, except for minibuses.

The dimensions of a standard garage are 3 x 6 m (frame drawing).

We calculate the area of all surfaces of the garage:

Side walls: 2m x 6m x 2pcs = 24 m2.
Gable roof including canopies: 2m x 1.9m x 6.2m x 2pcs = 47 m2.
Rear, end wall and gate: 3m x 2m x 2pcs = 12 m2.
Two triangular pediments, the approximate area of which is 4 m2.
Floor (if any): 3m x 6m = 18 m2.

Adds all the results obtained: 24 + 47 + 12 + 4 + 18 = 105 m2.

For the walls we used sheet steel 4 mm thick; according to the table according to GOST, 1 m2 of such steel weighs 31.4 kg. We multiply the mass by the area: 105 m2 x 31.4 kg = 3297 kg.
We obtained the weight of the sheet metal used to sheath the garage. But that is not all! Now you need to add here the mass of the gate frame and the garage itself; it is usually made from a large equal-flange angle.

Let’s not make detailed calculations now; accuracy is not particularly needed here. Let's take an approximate average value, according to some sources it is 1000 kg.

The frame of a prefabricated garage weighs approximately 1 ton.

Important! If we add up all the obtained values, we will see that the weight of a metal garage, all-welded, with sheet metal cladding 4 mm thick is 4297 kg.

Materials and tools

What basic tools and materials are needed to build a reliable structure for vehicles. First of all, this is a frame that will be a reliable and stable support. Materials that can become such a frame are rectangular profile pipes, corners, galvanized profiles - they are quite often used for plasterboard structures.

All these materials, each in their own way, are perfect for construction. However, the best option would be rectangular pipes that bend well and do not break. The main indicator is their strength. To work with this material, you can use both welding and threaded connections.

When it comes to a metal garage project, everyone must act individually. After all, the size of the structure, the type of roof, the material for the cladding, as well as the financial capabilities of the future owner of the garage are taken into account.

In order for a collapsible garage to become part of a summer cottage, for example, there are many different plans and diagrams. Among them you can find a lightweight option. It is suitable for members of the male population who do not have a welding machine, or they simply do not know how to handle it. In this case, the entire structure will be mounted on threaded connections. Therefore, for work the master will need:

Locksmith kit, which includes standard tools.
Ten and twelve wrenches.
Electric drill and drill bit with a diameter of 6.5 millimeters;
Grinding machine with a set of wheels for metal cutting and grinding.
Screwdriver.

Prefabricated concrete garages (concrete garage)

We offer three types of Concrete garages with a width of 3200mm, 3420mm and 3900mm, length 6000mm. height 2600mm.

Surely many motorists have had to deal with the problem of arranging a parking lot for their vehicle. Many people prefer to use paid guarded parking lots, however, there are also some car owners who, for various reasons, want to have their own garage. In addition to its direct functions, a garage is also attractive because it can store various equipment and accessories for a car, and carry out minor repairs, which is very difficult in a parking lot or garage complex. One of the most popular today are reinforced concrete garages.

From a technical point of view, a reinforced concrete garage is a structure made in the form of a monolithic box. Since reinforced concrete structures are quite heavy in weight, it is quite natural that prefabricated reinforced concrete garages are especially popular, the delivery of material for which in parts is most economically beneficial for the buyer. Often, for a buyer who has studied the market, it becomes quite obvious that buying a reinforced concrete garage is much more profitable both economically and in terms of labor costs compared to building a garage from other materials. This design has many advantages: quick construction, convenient transportation to the assembly site, no welding work, the ability to quickly dismantle and transport to a new location.

Of course, an important factor is that the building materials market offers a fairly wide range; any buyer can choose almost any reinforced concrete garage, the price of which suits him. Moreover, the market makes it possible to choose any size, shape of garages and offer relatively low prices compared to building a garage from other building materials.

How to deliver?

Unlike ordinary scrap metal, cutting railway cars into scrap is a specific process.

Article on the topic: Is emergency lighting necessary in the garage?

First, you need to cut the car. This is quite an expensive matter. The costs of work, energy costs, etc. are taken into account. This will require special equipment and qualified service personnel. Also in this case, it will be necessary to attend to the issue of transportation. The most convenient way is to call a team from the metal receiving facility, who will load and transport the cargo to the scrap metal collection point. As a rule, such services are provided free of charge, but given the weight of the car, special equipment will be required not only for transportation, but also for loading. This will incur additional costs. Also, the metal receiving team can independently dismantle and cut the car - in this case the price will decrease.

Cutting a car with hydraulic shears is the fastest and best solution

Some metal receiving stations are equipped with a railway siding. This simplifies the disassembly process. All you have to do is drive the car into this dead end, and a team of workers will independently “unravel” it. All you have to do is watch the process or receive money immediately.

How much does a garage weigh | Rental of special equipment in Chelyabinsk

Very often, when transporting metal garages, the question arises: how to find out the weight of a garage or change house?

Added: Garage weight calculator

To do this, you need to know the volume of metal from which the garage is made. Below is the frame and dimensions of a typical 6x3m oversized garage.

Let's calculate the area of all the walls of the garage:

roof including slope and canopies: 2*(2*1.9*6.2) = 47m2
side walls 2pcs: 2*(2*6) = 24m2
floor: 6*3 = 18m2
back wall and gate: 2*(3*2+2) (triangle) = 16m2

Total area of the entire surface of the garage: 47+24+18+16 = 105m2

Now let’s calculate the volume of metal, with a garage wall thickness of 3mm

The mass of 1m3 of metal is on average 7900 kg, hence the weight of the garage lining

0.315*7900 = 2500 kg

But this is only the sheathing; the frame of corners and gates weighs about 1000 kg.

The total weight of the 6x3m garage is at least 3500kg.

If the wall thickness is 4mm it will already be 4300kg.

Thus, iron garages usually weigh from 2-3 to 5 tons.

Design Features

Basically, such garages are made from metal profile sheets, and the reliability of the product is ensured by the thickness of the material. The shape of the building corresponds to the name of the structure - semicircular. But there is another option - a garage pencil case, which is presented in the form of a long metal structure.

Article on the topic: How to calculate square meters of a garage

The price of this design depends on the materials used and dimensions. These can be standard metal sheets or options with a special polymer plastic coating. They bend easily, acquire the desired shape, but remain quite strong.

Adviсe

Shells are very convenient and compact. To make them even better, you can use additional tips.

So, for example, car enthusiasts who spend a lot of time repairing or tuning their cars will like the idea of at least a little insulating the garage. To do this, you need to sheathe it from the inside with panels. The classic heating option is unlikely to work here.

It is not worth saving on the insulation of a structure in the same way as on its protection. The anti-corrosion coating chosen to protect the metal must be of high quality so that the building lasts longer. If the shell is placed in a place with a cold or rainy climate, the protective layer will need to be renewed over time. Not only the appearance of the garage, but also the level of security of the car depends on this.

And finally, before installing a “pencil case”, especially in the city, it is worth checking again how legal it is. Laws change over time. To be sure that the new building will not be forced to be demolished or moved to another location, you need to clarify what rules are in force now.

The following video provides an overview of the shell carport.

Instructions for assembling an Izhora garage with your own hands

Before you begin the assembly process, invite a friend to help you. Because it is difficult to cope with such work alone. Be sure to prepare all the necessary tools and supplies. The tools you will definitely need are:

hammer;
sledgehammer;
box wrench;
locksmith's beard.

There are two ways to assemble such a structure.

1st method (for this assembly you must invite a friend):

Begin assembling the end wall sections.
Assemble the side sections together.
Cover the walls with a roof.
Install the gate.

Method 2 (you can do it yourself):

Start installing the garage from the back wall.
Add side panels to the end.
Attach the roof next to the side panels.
Finish the assembly by installing the gate.

Specifications

The classic “shell” garage is used to store a passenger car. As a rule, it consists of two steel or reinforced concrete doors. One of them is firmly fixed and stands on the floor. But the second one, like a gate, opens. It rises, rotates and lies on top of the base of the gate.

It turns out that when opened, half of the car immediately ends up on the street.

Materials used

Durable metal is used to make the garage. Thick sheets, as a rule, weigh quite a lot. Typically their weight is within a ton. Therefore, it can be difficult to work with them without using special equipment.

It is also impossible not to note the fact that the shell is almost impossible to lift and move without a crane.

Safety

The structure, made of two doors, is considered vulnerable by many. After all, snow or raindrops can easily fall into the gap between them. In order to further protect the car, experts recommend using various seals. As an alternative, canvas capes are also purchased. However, this option is also risky, since the metal under the tarpaulin may become rusty.

In addition to weather conditions, the car must also be protected from vandals. The lock is installed at the junction of two doors. To would-be robbers, shells usually seem like easy pickings. That is why it is recommended to choose the most reliable locking schemes .

What are the standard sizes of reinforced concrete slabs?

Let's consider the option - the components of a precast concrete garage kit are wall panels for the sides, one wall panel for the rear of the garage, two floor panels, panels for the basement, and a front panel for the gate opening.

A garage of size 6000-3360-2200, using M200 reinforced concrete products, will be represented by right and left wall panels from a pair of slabs of size 6000-2200/2300-140.
The rear part of the reinforced concrete garage is represented by a slab 3500-2200-140.
Extension for gate 6200-2300-140, two reinforced concrete slabs.
And three pieces of reinforced concrete for installing floors. Slab size 3500-2200-120.

Video description

In the video you can see a prefabricated garage, which is easy to transport and quick to install:

To speed up the assembly of the shell pencil case garage, you can pre-order the production of individual sections. Pre-prepared holes for fasteners will also speed up the assembly process. All parts must be cleaned and polished. The frame must be coated with a special anti-corrosion agent. This will allow you to avoid serious problems during the operation of the structure in the future. Then everything can be painted. It is advisable to carry out preventive maintenance and treatment of metal structural elements once a year.

Metal elements must be coated with a special anti-corrosion agent.

This might be interesting!
In the article at the following link, read about a country house with a veranda.