How to remove the front seats on a VAZ 2114 and 2115

The reasons why you have to remove the front seats on VAZ 2114 and 2115 cars are different, and the main ones will be given below.

• damage to the chair itself
• replacing floor carpet
• car floor soundproofing
• seat upholstery with leather or other material

In order to remove the front seats on Lada Samara cars, you will need the following tool:

• 8 mm socket (or torx e10 for late cars after 2007)
• ratchet handle or crank
• 13 mm wrench or socket

How to remove the front seats on a VAZ 2114 and 2115

The reasons why you have to remove the front seats on VAZ 2114 and 2115 cars are different, and the main ones will be given below.

• damage to the chair itself
• replacing floor carpet
• car floor soundproofing
• seat upholstery with leather or other material

In order to remove the front seats on Lada Samara cars, you will need the following tool:

• 8 mm socket (or torx e10 for late cars after 2007)
• ratchet handle or crank
• 13 mm wrench or socket

Removal and installation of front seats on VAZ 2114 and 2115

The first step is to disconnect the power wires from the heated seats, if such an option is present on your car. Then, using a 13mm wrench or a socket, unscrew the 4 nuts securing the front seat pipe. This can be clearly seen in the photo below:

If it is problematic to do this using a head, then you can use a regular open-end wrench. If necessary, the torsion bars should also be pulled out by pulling each edge with medium force.

Now we jerk the front part of the car seat up, resulting in the following:

In this case, the seat mounting bolts in the front part become easily accessible. Unscrew the fastenings of the slide on both sides.

Now, by lifting the lever, we move the seat forward, thereby freeing access to the bolt securing the slide in the rear. We also unscrew one bolt on each side:

After which you can remove the seat, because nothing else holds it.

The seat is replaced if necessary and installation is carried out in the reverse order. It is worth noting that if you replace it with a new one, you will have to pay at least 4,500 rubles for one new seat 2114 or 2115. But the quality of the seats sold in the store is obviously worse than the factory ones. Therefore, the best option is to buy used seats at a salvage yard from a fresh car at a more than adequate price.

Useful information about seats on VAZ 2108, VAZ 2109, VAZ 21099

Note! From this article you will learn how to adjust the position of the front seats of your car, as well as remove the headrests from them, and in addition to all this, unfold and fold the back seat of the car!

Adjusting the front seats of your car:

1) In order to move the front seat of the car, back or forward, use a special lever, for this:

1. First, lift the lever to the upper position, and then, by moving the seat back or forward, adjust its position; after completing the adjustment, lower the lever to the very bottom, until it stops.

2) Next, adjust the backrest angle you need by grabbing the rotating backrest position knob and adjusting its position to suit you.

Removing the head restraints:

1) First, grab the lower or upper part of the headrest, whichever is most comfortable for you.

2) And then, using force, pull the headrest sharply upward from the seat, and then remove it.

Rear seat layout:

1) First, find a small loop, which is usually located under the central part of the seat, and then remove it from there.

2) Then, by pulling this same loop, raise the rear seat to the maximum possible level.

Note! There are times when the rear seat cannot be raised fully because the two front seats are in the way, but if this happens to you, then move both front seats forward until they stop! (see Adjusting the front seats)

3) Next, move the center seat back lock lever to the far left position.

4) And then fold the back of the rear seat as far as possible.

How to remove a VAZ 2114 seat: we consider all options

Many car enthusiasts are wondering how to remove seats on a VAZ 2114 or how to replace them?

The reasons for such manipulations can be very different:

• wear or serious damage to seats;
• the need to replace the floor covering;
• the need to glue the floors with soundproofing material;
• reupholstery of seats with new material (for example, leather);
• installation of alternative seats (both rear and front).

When choosing new seats to replace the basic ones, you should first of all pay attention not to their convenience and performance, but to the compatibility of their fastening with the fastening of the car.

In addition, various other situations may arise in which it may be necessary to dismantle and subsequently install the seats. We’ll look at how to do this as quickly and correctly as possible below.

Covers or seats?

For many, buying new car seats is associated with the desire to transform the appearance of the interior of their car. That is, they care little about the issue of comfort or they have only recently started driving. That’s why they don’t think about the issue of convenience.

If you have ever driven modern cars from top manufacturers, you have probably felt the difference between the seats. But you can’t buy such a car for yourself yet. So why not bring your fourteenth to this level of comfort by purchasing new seats? Good idea.

The covers only create the appearance of a beautiful, cozy interior. The landing was uncomfortable and will remain so.

Set your priorities and think about what is more important to you - a healthy back or a beautiful picture. In addition, by replacing the seats, you can put very beautiful covers on them.

Removal and installation of front seats

And so, let’s look at the question - how to remove the front seats on a VAZ 2114.

To perform this operation we will need the following set of tools:

• flat screwdriver;
• ratchet;
• knob;
• 8 mm head (or Torx 10 - in late models);
• 13 mm socket or a simple 13mm wrench.

The front seats are dismantled according to the following scheme:

1. Disconnect the heated seat wiring harnesses (if equipped).
2. Using a 13mm wrench, unscrew the four nuts securing the front seat tube.

1. If necessary, remove the torsion bars by pulling forcefully at their edges.

1. Raise the seat (you need to do this with a jerk) to its highest position (as far as possible), after which access to its fastening will open.

1. Unscrew the bolts securing the seat slides in the front (on both sides).
2. Pull the locking lever to move the seat forward.

1. Unscrew the bolts securing the seat slide at the rear (on both sides).
2. Remove the vacated seat.

Installing the seat in the car is done in exactly the same way, but in the reverse order (it should be noted that this diagram is relevant for both front seats - the driver's and the passenger's).

When purchasing new front seats, the best option would be to give preference to the so-called anatomical ones, which allow you to feel comfortable behind the wheel even on long trips.

Removing seats VAZ 2109 | Repair VAZ 2108 2109 21099

The front seat of the VAZ 2108 2109 21099 is removed if it is broken or during anti-corrosion treatment of the body inside the cabin. The rear seat, opposite, is removed very often, especially if the car is used to transport anything: you can put boards, a refrigerator, 6-7 bags of potatoes, etc. When you remove the back seat, the car becomes very roomy, as every owner of a V8 and Nine knows. Also, the rear seat has to be removed to deal with problems with the fuel level sensor or the fuel pump on the injector, since it is located directly under the seat. In order to dismantle the seats of the VAZ 2108 2109 21099, the following tool is needed: 1) A straight and Phillips screwdriver. 2) Wrench 133) Head 8. Removing front seats VAZ 2108 2109 21099: 1) Using wrench 13, unscrew the four nuts under the seat.

Removing the front seat of a VAZ 2109

Now its front part can be lifted up. 2) Unscrew the four bolts that secure the slide to the car body.

Raise the seat up

This is done using a 8-mm socket. If the bolts have not been unscrewed for a long time, they are unscrewed with force.

Front seat slides VAZ 2109

3) Remove the seat and take it out of the car.

VAZ 2109 seats removed

Removing the rear seat of a VAZ 2108 2109 21099: 1) First, unscrew the two bolts securing the back of the rear seat to the body. Some people who frequently remove the rear seat do not bolt the backrest, but simply insert it into the guides.

Rear seat guides VAZ 2109

2) Bend the lever behind the backrest and, pressing along the edges, squeeze it out of the fastenings.

The back of the rear seat has been removed.3) In order to remove the rear seat cushion VAZ 2108 2109 21099 you need to unscrew two bolts with a Phillips screwdriver.4) Then slightly lift the cushion and pull the lever under it.

Lever under the rear seat

Then the seat will be removed.

The procedure for installing the seats is the reverse order for removing them and is not difficult at all. Produced using the same tool.

What to pay attention to:

— The studs to which the front seat is attached may become warped due to rotten metal underneath. Try not to deform them again, as they may fall off and will have to be welded. — The 8-point bolts that secure the front seat slides to the body must be unscrewed with a 8-point head. You simply cannot get to them with an open-end wrench, and they are tightened with good force. Home

Replacing rear passenger seats

In addition to replacing or repairing the front seats, quite often the question arises of how to remove the rear seat on a VAZ 2114. In most cases, such an operation becomes necessary when the car is often used to transport passengers in the rear seats, and the existing seats are for some reason reasons are not satisfied.

In this case, you can dismantle the base seats and install new ones in their place - more appropriate to the anatomical data of the passengers (currently, the choice of such seats, having a wide variety of shapes and sizes, is quite wide).

In addition, many car enthusiasts install rear seats from various foreign cars, most often from Ford or Audi - since they are much more comfortable than the “original” VAZ seats, and at the same time can be installed in the car with minimal changes to the design of the fasteners.

In order to remove the seats themselves, you need to perform a number of simple operations:

• use a flat screwdriver or a strong blade to pry off the protective lining located just below the seat cushion;
• unscrew the two fastening bolts holding the pillow from the sides (a 10 mm socket is required);
• unscrew the bolts located at the bottom of the seats (with the same head);
• remove the vacated seats (they are no longer secured by anything).

Installation of new passenger seats in place is carried out (as in the case of the front seats) in exactly the same order, but in reverse order.

Kinds

First, let's look at the types of seats that you can purchase for your VAZ 2114. There are three categories in total, the advantages and disadvantages of which are described in more detail in our table.

Don't chase fashion when purchasing sports or racing seats for regular city roads. But if you are adapting your VAZ for competitions, then it is categorically not recommended to go on the tracks on ordinary seats.

High comfort chairs

What to choose

We have decided on the types of seats, but there are a great variety of them depending on the manufacturer, size, functions, etc.

Since the VAZ 2114 is a car more likely for city roads, we will focus on the choice of anatomical seats.

Let's discuss several points for choosing them.

1. Origin. Here the choice is between used and new seats. The new ones are more expensive, but they certainly have more advantages. A good place to look for used seat sets is car dismantling yards, where you can touch and inspect the product with your own hands. The choice depends on you and your financial capabilities.
2. Equipment. The presence of armrests and headrests is strongly encouraged. Make sure that the chairs come with all the necessary components and fasteners. They are not always provided by the seller, so ask in advance about the installation details.
3. Fastenings. Some seats from foreign cars fit perfectly under the standard VAZ holes for installation. For others, you have to do a little modification in the form of using adapters or creating additional holes. And there are also those, for the installation of which you will have to almost completely redo the seat on the body. This is far from the best option, since you will have to spend a lot of time and money.
4. Manufacturer. A lot depends on who exactly made the seats you choose. If you are interested in kits from foreign cars, then seats from Ford have proven themselves to be quite good. But keep in mind that some may be too wide, which will complicate access to the handbrake and will not allow you to move the seat back and forth. Take measurements in advance. There is also a company called UNP. It specializes in the manufacture of both anatomical and sports seats for cars of the domestic manufacturer - AvtoVAZ. They have a higher quality finish and are offered with all the necessary accessories and fasteners. Working with them is more convenient and easier.

Alternative seating

As we can see from the above, the answer to the question - how to raise the rear seat of a VAZ 2114 - is quite simple, since it is attached using a minimum number of fixing elements and does not require the use of a large number of tools. But another, no less important issue is the choice of new, alternative seats.

Many motorists, as already mentioned, install on their VAZ 2114 seats from other models and even other brands of cars (for example, seats from Ford). At the same time, when choosing them, you should pay close attention to their dimensions and fastening features (although very often motorists look specifically at the “performance” characteristics - convenience, wear resistance, anatomy, etc.).

The same rule applies to the front seats - the fewer modifications that need to be made during installation, the better. It should also be noted that when replacing the front seats, you should pay attention to the so-called “anatomical” seats (for example, manufactured by UNP).

They allow you to spend long periods of time driving and travel for many hours without feeling any fatigue or discomfort in your back and joints (such seats are especially recommended for frequent and long drives in urban environments).

Replacing seats

Installing seats in a car may be necessary for various reasons, so in each case there are certain nuances that are worth paying attention to. The choice of replacement will largely depend on the location of the interior elements. For example, the front seats are replaced most often because they are used more actively. Drivers use their cars every day, so comfort during the trip plays an important role for them. Depending on your driving style and the purpose of the car, first choose the type of seat, and then the model.

The two rear passenger seats can be replaced if more than two people are needed frequently. Models here should be selected in accordance with your finances.

Because of these operational features, it is worth approaching the choice of seemingly identical seats in different ways.

When selecting a replacement for both options, you should pay attention to many factors: height, weight of the person, figure, as well as other anatomical features. If the car is used only by family members, then you should take care of their comfort and choose seat models that best suit their requirements.

We improve the interior with covers

If the design of the seats to some extent suits the owner of the VAZ 2114, then the main problem in the cabin is the presence of secondary factors:

• wear and tear of upholstery materials;
• all kinds of pollution;
• greasy spots.

Naturally, such an arrangement is unlikely to suit any owner of a VAZ 2114 car. The upholstery of domestically produced cars wears out very quickly - all this is the result of the use of low-quality materials.

If the upholstery in the car has not yet lost its original appearance and is in good condition, then it would be advisable to protect the seats with special covers.

In fact, this is one of the cheapest tuning options, which contributes to the following improvements:

• improving the appearance of the interior and giving it some individuality;
• comprehensive protection against abrasion and contamination;
• Some manufacturers offer products with special inserts that improve the comfort of the driver and passengers.

Car covers are inexpensive and easy to clean from all kinds of dirt. There are a large number of options on the market today, among which you can easily get lost. First, just decide whether to buy ready-made covers or have them made to order.

Ready-made solutions include covers with padding polyester inserts that provide back support. Such products, as a rule, have increased resistance to wear. Variations of available colors will allow you to choose covers to match other interior elements so that everything looks harmonious.

Removing and replacing front seats

Now it’s worth talking about how to remove the front pair of seats of a VAZ 2114. For dismantling you will need a standard kit:

• flat screwdriver;
• set of removable heads;
• ratchet;
• collar

The disassembly procedure is as follows:

1. We secure the car for the duration of the work. At will, we select one of the seats from the pair and push it forward all the way.
2. You will need to remove the cables.
3. After the cables have been removed, you need to tilt the seat back as far as possible until the fastenings underneath are visible.
4. The chair is secured with four nuts that hold the entire structure on the bracket. Unscrew them, part of the structure should now “move” freely.
5. Next, lift the seat to gain access to the remaining fasteners.
6. You need to tighten two bolts. After this, the seat can be removed and taken out of the cabin.
7. We remove the second front seat in the same way.

Before installing new seats, clean and lubricate the mounting points. In some cases, you will have to modify the frame, and in some, change the mounting locations - everything will depend on the model of the chair that you are going to install.

FRONT SEAT VAZ 2101.

How to remove the front seat

Seats are probably one of the most important parts of the car interior, and, in general, the body. The safety of the driver and passengers, and simply the convenience of driving, depends on the serviceability of the seats. The seats of classic Lada cars are obsolete, and recently craftsmen, through simple alterations, have installed seats from foreign-made cars purchased at auto showdowns. But more on that later.

In this article we will tell you how to remove the front seat, replace faulty slides, and install the seat in its original place. Arm yourself with a 8mm socket wrench and a 13mm wrench.

To begin with, to make it easier to understand, it would not be superfluous to familiarize yourself with the structure and location of the components of the movable seat mechanism. Brackets are installed on the floor of the body, to which the guide rails are attached, which in turn are installed on the seats.

In the image, the arrows show the mounting locations of the bolts in the front with the seat fully moved back. If the seat is moved all the way forward, then the same bolts are located in the back.

Here the seat is shown from below to make it easier to show where the bolts securing the sliders to the cushion frame are located. The location of the rear mounting bolts is similar.

Next, to remove the seat, move it back until it stops, on the guide of the internal slide, unscrew the nut securing the bolt, then remove the spring washer.

The arrow shows where the nut is located; unscrew it and remove the bolt so as not to lose it later when removing the seat. Next, unscrew the fastening bolt on the outer slide and remove the washer.

To unscrew the fastenings from the rear side, move the seat as far forward as possible until it stops. Then unscrew the bolts securing the outer and inner slides. Remove the seat from the interior.

Using pliers, remove the outer slide spring

If you decide that you need to replace the slide, move the guide forward until it stops, then unscrew the slider mounting bolt and remove the slide. The internal slides are changed in the same way. The slides should be installed in the opposite order to removal.

Rear passenger seats

How to remove the rear pair of passenger seats? Removing seats in VAZ models, starting from 2108 and ending with 2115, is done in exactly the same way. The set of tools remains unchanged from the first example. Here is the sequence of actions:

1. The rear seats do not need to be moved, they are fixed. To access the fastenings, use a flat screwdriver to pry up the protective pad just below the seat cushion.
2. First, unscrew the two bolts that hold the pillows on the side. Here you need a 10mm head.
3. Next, the same fastenings must be removed in the lower part of the seat backs using exactly the same key.
4. After unscrewing all the bolts, you can safely remove the rear seat.

Ford or Audi A4 series rear seats are recommended as replacements. Why these options? They will require minimal correction of the frame and fastenings from you, in addition, they will fit perfectly into the interior of the cabin.

Of course, you can choose other seat options, but it will require more modifications, parts and time to properly attach the new passenger seats.

How to fold the back seat of a VAZ 2108?

The rear seat can be folded forward to create additional luggage space. Pull the backrest lock handle towards you and fold the backrest forward. Pull the seat by its straps towards the luggage compartment, and then fold the entire seat by pulling it up and forward until it locks into place.

Interesting materials:

How long to cook white beans until tender? How long to cook homemade chicken breast? How long does it take to cook kazy from horse meat? How long does it take to cook pork skin? How long does it take to cook a small chicken? How many species of sharks are there in the world? How many types of pencils are there? How much wet food should I give my kitten per day? How long does it take for heat to travel from the Sun to the Earth? How many scarlet nirn roots are there in total?

Secure fixation

When choosing new seats for your VAZ 2114, pay attention not only to their price and convenience, but also to the method of fastening. Some seat models are very difficult to fit into the cabin, although they may suit your preferences. Improperly securing the seats can cause injury, especially at high speeds or in accidental collisions. If you have found a suitable model of seat, but it is not securely attached to its future installation location, take the car to a workshop where all the work will be carried out for you.

As mentioned earlier, it is better to take the recommended models of seats from foreign cars for replacement from Ford or Audi. Many drivers have noticed that Opel seats are also excellent for replacement and require a minimum of additions. Even chairs from Hyundai can become a more or less comfortable and quite acceptable option, if you slightly alter the design of the frame and fastenings.

The dangers of uncomfortable car seats

Safety and driver comfort in any vehicle begins with the driver's seat. An insufficiently developed design significantly affects the general condition of the driver during long trips. It is possible that your back, arms and other troubles may become numb, which significantly distracts you from driving. The presence of comfortable seats is the primary factor when buying a car. Because not everyone wants to exercise after a long trip.

What can be done to the interior of the VAZ 2114 to improve comfort:

• improve appearance through tuning;
• reupholster the interior with covers;
• replace standard seats with sports or anatomical options;
• perform complex tuning.

Additional replacement options

For all city cars, the front seats should be quite comfortable. If you are going to update your interior, pay attention to anatomical seats. A correctly selected anatomical seat will allow the driver to find a comfortable position for driving the car. It might seem like a small thing, but it relieves unpleasant back and neck pain, as well as stiffness in the limbs during prolonged sitting.

Among seat manufacturers, it is recommended to look at products from UNP.

VESKO-TRANS.RU

AutoNews / Reviews / Tests

• Home
• Auto garage
• How to remove the front seats on a VAZ 2114

How to remove the front seats on a VAZ 2114

The prerequisites for such manipulations are very different:

1. wear and tear, as this is still called severe seat damage;
2. the need to change gender;
3. the need to glue soundproofing material to the floor;
4. rearrangement of seats with new material (for example, leather);
5. installation of other seats (both rear and front).

When choosing new seats instead of basic ones, it is important to pay attention not only to their comfort and efficiency, but also to the compatibility of their fastening with a car one.

In addition, there will be different situations when dismantling and subsequent placement will be required. We will discuss below how to do this very quickly and correctly.

And yes, we will analyze the questions - how to remove the front seats on a VAZ 2114.

Seat Design Vase 2114

To perform this operation we will need the following set of tools:

1. flat screwdriver;
2. ratchet;
3. collar;
4. 8 mm head (or Torx 10 in later models);
5. 13 mm head or 13 key.

Seat Removal Tools

The front seats are removed as follows:

• Disconnect the heated seat harnesses (for which the design is intended, if any).
• Using a size 13 wrench, loosen the four nuts that secure the front seat tube.

Remove the seat nuts

• If necessary, remove the torsion bars by pulling firmly on the edges.

Dismantling

Before installing new chairs, you will have to get rid of the old ones. Accordingly, dismantling work cannot be avoided.

To work you will need:

• Flat-head, durable screwdriver;
• Set of heads;
• Collar;
• Ratchet.

Dismantling process

The procedure itself looks like this:

1. Pull the seat forward all the way.
2. Remove the metal cables that allow the seats to move forward and backward more smoothly.
3. Now move the seat as far back as possible.
4. You will have access to the four nuts that hold the chair to the bracket. They need to be unscrewed.
5. Raise the seat slightly to remove the two rear mountings to the skid. There are regular bolts there.
6. Now carefully remove the seat from the car.
7. Do a similar procedure with the second chair.

The installation of new seats depends entirely on the features of their design. There are no universal instructions for installation.

Remove and remove

Next comes the process of installing new chairs. Before doing this, be sure to clean the mounting points, the bottom of the cabin, and get rid of all existing traces of rust.

How to raise the seat of a VAZ 2114

Many car enthusiasts are wondering how to remove seats on a VAZ 2114 or how to replace them?

The reasons for such manipulations can be very different:

• wear or serious damage to seats;
• the need to replace the floor covering;
• the need to glue the floors with soundproofing material;
• reupholstery of seats with new material (for example, leather);
• installation of alternative seats (both rear and front).

When choosing new seats to replace the basic ones, you should first of all pay attention not to their convenience and performance, but to the compatibility of their fastening with the fastening of the car.

In addition, various other situations may arise in which it may be necessary to dismantle and subsequently install the seats. We’ll look at how to do this as quickly and correctly as possible below.

Which seats are suitable for the VAZ 2114, or how to improve existing ones

Western car manufacturers pay a huge amount of attention to developing comfortable seats. Essentially, high-quality seats are the key to comfort for both driver and passengers. Therefore, today in most foreign cars you can often find anatomical designs that are equipped with lumbar support, and there is also lateral support.

Recently, the domestic auto industry has begun to improve car seats for the benefit of comfort. But what about the owners of those generations where such options were not provided? In this case, the solution to the problem comes down to tuning the existing seats, or completely replacing the seats. This article will tell you how to modify the interior of a VAZ 2114, as well as which seats will fit in the car without complex modifications.

Removal and installation of front seats

And so, let’s look at the question - how to remove the front seats on a VAZ 2114.

To perform this operation we will need the following set of tools:

• flat screwdriver;
• ratchet;
• knob;
• 8 mm head (or Torx 10 - in late models);
• 13 mm socket or a simple 13mm wrench.

The front seats are dismantled according to the following scheme:

1. Disconnect the heated seat wiring harnesses (if equipped).
2. Using a 13mm wrench, unscrew the four nuts securing the front seat tube.

1. If necessary, remove the torsion bars by pulling forcefully at their edges.

Replacing rear passenger seats

In addition to replacing or repairing the front seats, quite often the question arises of how to remove the rear seat on a VAZ 2114. In most cases, such an operation becomes necessary when the car is often used to transport passengers in the rear seats, and the existing seats are for some reason reasons are not satisfied.

In this case, you can dismantle the base seats and install new ones in their place - more appropriate to the anatomical data of the passengers (currently, the choice of such seats, having a wide variety of shapes and sizes, is quite wide).

In addition, many car enthusiasts install rear seats from various foreign cars, most often from Ford or Audi - since they are much more comfortable than the “original” VAZ seats, and at the same time can be installed in the car with minimal changes to the design of the fasteners.

In order to remove the seats themselves, you need to perform a number of simple operations:

• use a flat screwdriver or a strong blade to pry off the protective lining located just below the seat cushion;
• unscrew the two fastening bolts holding the pillow from the sides (a 10 mm socket is required);
• unscrew the bolts located at the bottom of the seats (with the same head);
• remove the vacated seats (they are no longer secured by anything).

Installation of new passenger seats in place is carried out (as in the case of the front seats) in exactly the same order, but in reverse order.

If, instead of the basic one, a seat from a different brand of car is installed, then there is a possibility that additional changes will need to be made to its design (nominally, additional mounting holes will be drilled, but in most situations these changes may be much more).

Alternative seating

As we can see from the above, the answer to the question - how to raise the rear seat of a VAZ 2114 - is quite simple, since it is attached using a minimum number of fixing elements and does not require the use of a large number of tools. But another, no less important issue is the choice of new, alternative seats.

Many motorists, as already mentioned, install on their VAZ 2114 seats from other models and even other brands of cars (for example, seats from Ford). At the same time, when choosing them, you should pay close attention to their dimensions and fastening features (although very often motorists look specifically at the “performance” characteristics - convenience, wear resistance, anatomy, etc.).

The same rule applies to the front seats - the fewer modifications that need to be made during installation, the better. It should also be noted that when replacing the front seats, you should pay attention to the so-called “anatomical” seats (for example, manufactured by UNP).

They allow you to spend long periods of time driving and travel for many hours without feeling any fatigue or discomfort in your back and joints (such seats are especially recommended for frequent and long drives in urban environments).

Useful video

You can find more information in the video below:

Not all Lada car seats are equally comfortable. One of the main requirements for the driver's seat is height adjustment. The owners of Lada XRAY were the luckiest in this regard, because... All crossover configurations have this useful option. Other Lada models have a driver's seat lift only in richer versions, or not at all. Let's look at how you can modify the driver's seat with your own hands.

Owners of cars that do not have seat height adjustment can raise the cushion themselves in one of several ways:

1. Place a piece of plywood on the bottom of the seat between the springs and the cushion (the safest and fastest way).

2. Place nuts under the front part of the slide (most often they are raised by 2.5..5 cm). Only the front part of the chair rises.

3. Place a profile pipe under the slide. The front and back of the seat lifts up.

In the last two cases, you will have to use longer mounting bolts, which may have a negative impact on safety. To lower the seat, you can remove part of the fastening (vertical pipe) using a grinder and welding.

All these modifications to the seat allow for height adjustment, but do not allow the chair to be lowered or raised at the same time. That is, if the car is driven by more than one person (for example, a husband and wife), you cannot do without the “seat lift” function. In this case, there are two correct ways:

1. Conversion of Vesta or Largus to a higher configuration, installing seats from the “comfort” or “luxury” version, respectively;
2. For owners of Granta, Kalina, Priora or Niva 4x4, install seats from a foreign car or from modern Lada models.

Are you satisfied with the height of the driver's seat without adjustments? Is it worth modifying the standard seat or is it better to replace it with an alternative one? Let us remind you that the trip will become more comfortable if you install a suitable armrest or lumbar support in the car interior.

The loop is located closer to the right carabiner (if you look in the direction of travel of the car).

There are two options to catch the loop:

1. hands; 2. using a homemade hook.

First option: with your hands. Suitable for those with thin, long fingers. We spread the seat cushions as far as possible. We put our fingers between them. We are trying to find it and pull it out.

Second option. We make a hook from a fairly stiff wire. We process the end with a file - we make a hemisphere at the end. That is, to remove burrs. This will ensure the safety of the seats - we won’t tear them. Next: insert the hook between the seats and catch the loop. We take it out.