What is the best way to open a VAZ-2109 car using improvised means, that is, without a key? A question like this comes up relatively rarely. In such a situation, many motorists simply do not know what to do. The worst thing is if the trouble happens somewhere along the way, far from the garage and the tools in it.
Most often, the door does not open when:
- the driver absent-mindedly leaves the key in the car;
- the alarm system fails;
- the battery is discharged, etc.
Fortunately, in the model of the Volzhsky Automobile Plant in question, it is quite easy to open a locked door without damaging it completely or only slightly damaging it.
The most gentle options
You should use a rope if your car has mushroom-shaped internal locking buttons. A not too thick twine about a meter long will suit you. At worst, take a lace from your shoe. The main thing is that it reaches with a margin to the bottom of the window.
At one end of the twine, make a loose loop. Its size should be approximately twice the diameter of the lever.
Next, the driver's door needs to be pressed away from the body in the upper right corner. We push the prepared noose into the resulting gap and throw it on the button. It is unlikely that you will succeed the first time, but sooner or later, with due diligence and patience, everything will work out.
Then the rope, slightly stretched, is moved very carefully and slowly downwards (towards the door handle) and only then is it tightened tighter on the “fungus”.
After this, the string is returned to the upper corner of the door and the latch rises.
You can also use a piece of fairly stiff wire or an old electrode. A hook is made at one end of it. Further:
- move the glass seal on the driver's door directly opposite the lock button to the side;
- a hook is inserted inside;
- they put him under traction;
- they grab it and pull it up.
It is not difficult to open a closed car with a student's ruler. Very thin steel would be more suitable. The plastic one will most likely break and part of it will remain inside the door. It is inserted in the center of the glass - in this place there is a lock rod, which should be pressed. Before doing this, the door is pressed more tightly against the body of the car, leaning with the whole body - this way the bolt will move easier.
More traumatic options
The method described below is suitable if you need to get into the trunk and there is a cylinder on its door. You can open the lock here with a strong flat-head screwdriver. In particular, it is inserted into the well as deep as possible and turned with a sharp, strong movement towards the opening. Usually the mechanism works the first time. It is almost guaranteed that it will then have to be replaced.
A trunk with a standard lock can also be opened using a more barbaric method. It will only work if the metal is still strong enough. A rotten one will most likely just break. To do this, you need to grab the edge of the door with both hands on both sides of the locking device and pull it very strongly and sharply towards you. The problem is that with this method of opening the trunk is often deformed, so you should use it with the utmost caution.
Hacking the trunk lock
But what to do if you don’t get into the cabin, or you don’t get into the trunk from it? The larva will have to be rolled up. To do this, you will need a bayonet-type screwdriver, preferably with a square screwdriver at the end - drive it into the cylinder and turn it out until the locking plates inside the cylinder burst and it begins to rotate freely. This is an extreme method, after which the larva will have to be replaced.
If you have time, the tool for opening the cylinder is made from durable hexagons or “torxes” of a curved type: carefully, without overheating the metal, we grind one end until it gives it a shape similar to the shank of a key, after which we drive the resulting tool into the cylinder.
Video: How to open the trunk of a VAZ 21099 without a key
The main problem when roughly opening the cylinder is that it is often not the cylinder that rotates, but the metal of the trunk lid itself, the grooves of which hold the base of the cylinder in place. On a VAZ of the “classic” family, you will most likely turn the lock on the door rather than roll the cylinder. After this, it is problematic to install a new one - the way out to restore functionality would be to install a plug in the deformed hole, and electromechanical drives with 5-10 kilograms of force on the locking and opening rods.
How to open a VAZ 2110
How to open a jammed door? First of all, you need to check if your trunk is closed. If it is open, then you will not have to break the car and you will easily get into the interior. And the question of how to open without a key will be removed from the agenda.
How to open a VAZ 2110 without a key
If you are thinking about how to open a car without a key using a rough but quick method, you can break out the car window with a stone or other heavy object, but you need to remember that replacing glass is expensive.
Another option for rough opening is to drill out the lock with a drill. But this method is applicable only when there is access to electricity and a tool.
How to open the door of a VAZ 2110
How to open a car with minimal effort? In this situation, there is only one way out and it consists in contacting a specialized company for emergency opening of automobile locking systems.
It is worth noting that masters never resort to radical methods. They will try a lot of ways, but will keep your property intact. Their assortment includes not only modern master keys, but also many other special tools.
Moreover, the services are much cheaper than replacing broken glass or completely replacing the locks on your car. Another very important advantage of this service is that specialists respond to your call as quickly as possible.
Emergency opening companies are located in every city, so no matter where you are, you will always receive qualified assistance.
Troubleshooting
If a key or silumin rod breaks, you should not immediately buy a new block with a handle. On sale you can find special repair kits for VAZ 2108-099 door handles, which contain these parts in 2 copies.
This way you will save money and easily change the key yourself by removing the handle using the following sequence of actions:
- Remove the decorative panel.
- Disconnect the rod connecting it to the locking device from the handle mechanism.
- With the glass fully up, unscrew the 2 fastenings of the handle to the door card.
- Remove the handle, replace the parts and put it back.
If the rod is disconnected, then you need to remove the inner lining and put it in place, as described above. Using the moment when the facing panel is removed, check what caused the disconnection of this rod so that history does not repeat itself when the door is slammed.
Malfunctions of the locking mechanism can only be eliminated by removing it. In a situation where the device has a lot of wear, as happens on the driver and front passenger doors, it is recommended to replace the lock with a new one.
After installing it in place, adjustment will be required to ensure precise alignment of the locking parts. To adjust, the lock will have to be fixed in different positions, achieving the optimal one.
How to open a VAZ car
How to open a VAZ car without a key
The situation when the car door is closed and the keys are left in the cabin sometimes happens to all car enthusiasts. There is no point in panicking and taking ill-considered actions. Really opening a Russian car is not as difficult as it seems.
How to open a VAZ 2109
One of the simplest ways to answer the question of how to open without keys is to use a piece of rigid but flexible wire up to one meter long. You need to make a hook at the end of the wire, this structure needs to be inserted between the glass and the seal and find the door rod. Once you succeed, you need to pull the hook towards yourself and you will no longer have problems.
How to open a VAZ 2109 without a key
If you understand locking mechanisms and know how to use master keys or knitting needles, then you will not have any problems. You just need to install the master keys in the keyhole and, carefully operating them, carry out the necessary actions to open it.
The only disadvantage of the method is that not every motorist can boast of having such skills.
How to open the door of a VAZ 2109
If you keep spare keys at home or your friends or relatives have them and you are close enough to them, it would be wise to just go and get a duplicate.
Review of simple methods
Before you get nervous and fall into a stupor, think about the fact that the domestic auto industry, in principle, is not particularly airtight. In most metal joints, this characteristic is achieved with rubber bands, plugs and other elastic sound-absorbing nonsense.
At the same time, the design of the door plugs in models older than the VAZ 2110 does not allow the use of a fishing line (string), so trying to lower the glass with weight is pointless.
The following methods immediately come to mind on how to open the door of a VAZ 2114:
- We remember where the car keys are and think about how to deliver them to it. Leaving the car running (with the ignition on) is dangerous: firstly, the gas may run out, and secondly, the battery may die. In both cases, the doors will open and the car will remain open until you arrive. Therefore, it is better for someone else to bring them.
- We call a door opening company - specialists will arrive quickly and do everything instantly and inexpensively, but under two conditions. In the West, this problem is not so acute, but with the dominance of our compatriots, registration documents and licenses began to be checked there too. When the specialists arrive, they will want to make sure that the car is your property, for this they will check the specified documents. If they are not there or the car is on another person (godfather, matchmaker, etc.), they will not help you, because no one wants to be accomplices in the theft.
How to open a VAZ 2112
If you don’t know how to open a car if the lock has frozen in the cold, you will definitely find the instructions below useful.
The essence of the method is to heat the key with a lighter and insert it into the keyhole, thus melting the ice. It is quite possible that you will not succeed the first time. If the door of the VAZ 2110 still does not open, you can repeat the procedure several times.
Important: in order not to suffer with the lighter in the future, it is worth purchasing a special liquid from a car dealership intended for defrosting the lock.
How to open a VAZ 2112 without a key
Another method that will help those who do not know how to open a car without a key is the method based on the use of a ruler. To use it you will need to get a long, thin and strong metal ruler, pushing it under the glass, you can apply pressure to the locking mechanism and open the door.
How to open the door of a VAZ 2112
If you don’t have special equipment on hand, even an ordinary lace will help. You need to tie a loop on it and push it into the cabin by lowering the glass with your hands. Then all you have to do is hook the lock, tighten the loop and pull the cord towards you.
Therefore, the answer is very simple. Use a lanyard!
Radical approach
If there is no time, and nerves are at their limit, some car enthusiasts resort to them, but these are the worst ways to open a car. Imagine that you decided to sell your car in a year, and the buyer you came across was attentive and meticulous. Traces after an approach by brute force will remain with a 99% probability, and such a car will be sold for a very long time, because no one will believe that it was not in an accident.
If you decide then:
- We break out the lock - take a screwdriver and hammer it into the lock cylinder, and then turn it. This method is incredibly expensive, because further repairs are required. You will be faced with the fact that instead of one cylinder you will have to change all 5 (doors + trunk), and after the repair you will have two keys. In order to have only one key, you will have to order expensive locks and wait a long time, dooming yourself to the inability to use the car always open.
- We break the glass - when you damage the lock, but do not open the car, break the glass. It is necessary to break the rear door glass (preferably the right one). There are several reasons for this decision: firstly, a window sealed with tape will not spoil visibility, and secondly, if after breaking it turns out that the back door of the VAZ 2114 does not open, and you have to knock out all the glass to get through, you will have less wind later. And don’t break the glass with your hands - find a hammer, otherwise, in addition to a car mechanic, you will also need a surgeon.
WORTH KNOWING! Another tip is to buy the tape in advance, because if the fragments hang on it, you will not have to clean the interior. Imagine the area you are going to hit as a square and cover it with tape on only one side.
How to open a VAZ 2114
If you have a VAZ 2114, how can you open it with the help of specialists?
You can call the nearest service station and find out if they have a locksmith who knows how to open locks. The service station has all the tools that will help solve your problem. All you have to do is thank the master by paying for his services.
How to open the door of a VAZ 2114
If the door of the VAZ 2109 does not open and conventional methods do not produce results, you can resort to rough ones.
For example, you can forcefully insert a screwdriver into a keyhole and then turn the lock. Even if you cannot remove the lock, there will be no problems opening the door. Consider the fact that it is almost impossible to insert a screwdriver without a hammer.
Door opening method
If the VAZ-2109 door does not open from any side, then the cause of the breakdown is difficult to determine, since there is absolutely no access to the lock mechanism.
A somewhat simplified version of the breakdown occurs when the door does not slam shut completely and gets stuck in that position. Then it is possible to reach the latch from the outside with a sharp object.
To open a jammed door, you must first perform the following steps:
When simple means do not produce results, the door will have to be opened from inside the cabin, which will require removing its trim.
In practice, this is not easy to do, because the casing is pressed by the sash and it is difficult to pull it out without damage. But there is still no other way out: it is better to damage the inner panel than to mutilate the door itself.
To dismantle the decorative panel, you need to unscrew the armrest handle with a screwdriver, and then the storage shelf located at the bottom of the door card. Then the button that secures the lock from above is unscrewed and removed. Lastly, the window lifter handle and the opening handle frame are removed. Now you need to carefully separate the lining from the body using a pair of flathead screwdrivers and another suitable tool. You may be able to remove the trim without visible damage.
When the decorative panel is removed, access to the lock mechanism from the inside opens, although getting to it is inconvenient. Immediately check whether the rod running from the handle to the lock has fallen off. This is a fairly common malfunction that can be fixed with little effort. Put the rod in place and open the door.
If there are no visible reasons for the breakdown, simply try to open the door from the inside by working on the mechanism with various tools. If necessary, enlist the services of an assistant who will press or pull the door from the outside. Experience shows that such procedures for opening jammed doors can take a lot of time, so you will have to be patient.
How to open a VAZ 2115
It happens that the battery unexpectedly runs out for the owner, the alarm goes off and leaves the door locked. How to open it in this case?
It’s quite simple, you need to put a special pad between the body and the hood of the car, inflate it and make a small hole.
After this, you just need to connect the positive terminal of your car’s battery with a wire to the positive terminal of another, fixing the “minus” on the disk, and after connecting, press the key fob button. It is best to have someone help you with this procedure.
If you are confused and don’t know what to do, you can call the Ministry of Emergency Situations. However, the specialists of this service are not familiar with careful opening methods, and your car will definitely suffer.
As you can see, there are no hopeless situations.
The most open doors and trunk of VAZ-2109
without
a key
How best to open a VAZ- 2109
using means at hand, in other words, without a key? A similar question is asked comparatively infrequently. Under these circumstances, most car enthusiasts simply do not know what to do. The worst thing is if the problem occurs somewhere moving, far from the garage and the tools available on the personal computer.
In most cases, the door does not open when:
- the driver absent-mindedly leaves the key in the car;
- the alarm goes off;
- battery discharged, etc.
Fortunately, in the model of the Volzhsky Automobile Plant in question, it is easy to open a locked door without damaging it at all or only slightly damaging it.
Adequate methods
This will surprise many, but there are much more adequate methods to get into an automatically locked car without damaging it than radical and expensive ones.
So, the car is locked from the inside with the keys in the ignition, it’s a long drive to get the keys, and I don’t want to spend money either on a special company or on subsequent repairs:
1. Open the trunk to get into the cabin. There are several methods to perform this task:
- We apply a strong impulse blow with an open palm just below the lock, and the vibration will complete everything for you and the latch will open;
- take an awl (a woman’s nail file or manicure scissors) but not a screwdriver. We insert the existing object under the seal and press the tongue.
2. Open the hood and disconnect the battery. This is the simplest of the methods:
- we crawl under the car and find the cord leading to the hood lock; if that doesn’t work, we look for the lock tongue through the radiator grille;
- press the tongue mechanically or pull the cable and the hood opens;
- We approach the battery and knock down the negative terminal, and click it several times on the mount. The car body, which is a minus, is a large consumer and turning it on abruptly will create a small soft drop. It’s better not to touch the right one, because you can burn the ECU.
3. Open the door with wire. The sequence of actions is as follows:
- we find a stiff wire and an analogue of a woman’s nail file and get to work;
- use a thin object to pry out the glass seal near the lock;
- we insert the pre-bent wire into the prepared hole and lower it until it rests;
- the wire rests against the lock latch, so we turn it and turn it until it goes around it, when it “falls through” we pry it back;
- The opening procedure will take 2-5 minutes, and the door will be open; all that remains is to hammer the seal back.
4. Open with your phone. The most interesting, and most importantly effective method of how to open the door on a VAZ 2114. It is simple and amazing:
- you need to remember who has the second keys and call this person;
- bring the phone closer to the keyhole;
- the interlocutor at the other end presses the open button and the machine is open.
How to open a VAZ 99 (nine) without a key
How to open a VAZ
99 (nine)
without a key
.
You can also use a piece of fairly stiff wire or an old electrode. A hook is made at one end of it. Further:
- move the glass seal on the driver's door to the side directly opposite the lock button ;
- a hook is inserted inside;
- they put him under traction;
- they grab it and pull it up.
It's not difficult to open
a closed car and a student ruler. Very thin steel would be more suitable. The plastic one will most likely break and part of it will remain inside the door. It is inserted in the center of the glass - in this place there is a lock rod, which should be pressed. Before doing this, the door is pressed more tightly against the body of the car, leaning with the whole body - this way the bolt will move easier.
More traumatic options
The method described below is suitable if you need to get into the trunk and there is a cylinder on its door. Open
Constipation can be achieved here with a strong flat-head screwdriver. In particular, it is inserted into the well as deep as possible and turned with a sharp, strong movement towards the opening. Usually the mechanism works the first time. It is almost guaranteed that it will then have to be replaced.
How to open the hood of a VAZ 2109 without a cable.
A trunk with a standard lock can also be opened using a more barbaric method. It will only work if the metal is still strong enough. A rotten one will most likely just break. To do this, you need to grab the edge of the door with both hands on both sides of the locking device and pull it very strongly and sharply towards you. The problem is that with this method of opening the trunk is often deformed, so you should use it with the utmost caution.
In reality, the better option in a desperate situation is to break one of the rear windows. Here you can use a hammer or a cobblestone. New glass costs little - about 200 rubles, which is not that expensive compared to replacing a damaged trunk door.
There is a special offer on our website. You can get a free consultation with our corporate lawyer by simply submitting your question in the form below.
Recent Entries
New deal offers drivers a free car - life-saving brakes for drivers up to £1,600
A NEW deal offers motorists free 'brakes for life' which could reportedly save them up to £1,600. 'One-off payment
Record sales of trucks and powerful cars ensured strong dynamics in July sales of American Honda
Subaru promotes education with annual Subaru Loves Learning initiative
Best-in-Class Takeoff Power Now Standard on 2022 Ford Super Duty Power Cab
Categories
Test Drive
Ferrari Portofino 2019 review
Ferrari Portofino. this is a super stallion that you will ride every day Maximums Spectacular gearbox with excellent shift mechanics
