Why do the spark plugs on the injector flood and how to deal with it?

It is characteristic that the spark plugs are filled with gasoline less often in the warm season, and more often at sub-zero temperatures. So let’s try to figure out in order: why the spark plugs in the injector are flooded, what to do to start the engine at the exact moment when they are flooded, and how to prevent them from being flooded with gasoline in the injector.

Reasons why the spark plugs in the injector flood

Calcination of spark plugs filled with gasoline

In principle, the reason why the injector spark plugs flood is simple. And the tones lie in the peculiarities of the “electronic brain” of your car.

At subzero temperatures, mixing the fuel-air mixture requires some effort: more oxygen in cold air requires more gasoline. Accordingly, the ECU gives a command to the injector nozzles to increase the fuel supply, which they do in good faith.

And the following happens in the engine, especially if your car no longer has a new battery. The injectors supply fuel to the combustion chamber, the starter tries to create the necessary compression in the cylinders, while at the same time trying to provide a spark to generate a flash. Do not forget about the quality of fuel, which does not have ideal parameters.

As a result, with ideal compression, the injector spark plugs can start even with a minimum impulse, but ideal compression is only found in a new car. Actually, this is why, as a rule, the injector spark plugs of a new car do not fill.

The spark is weak, compression in the cold does not correspond to the parameters, and the injectors continue to supply fuel to the combustion chamber. Which, in turn, floods the candles and they simply stop showing signs of fiery life.

This is the answer to the question - why are they filled in on the injector?

What to do if the spark plugs on the injector are filled with gasoline

There are two options for resolving the issue. As a rule, the “smart” operating book says: if the injector spark plugs are filled with gasoline, you need to unscrew them and dry them. With the spark plugs removed, crank the starter for 10-15 seconds. Put it back in and start the engine. These are actions according to the manufacturer.

A proven popular driving method. If your spark plugs are filled with gasoline, before unscrewing and drying them, try to start the engine in the following way: purge mode.

For the injector: the gas pedal is pressed all the way to the floor. Use the starter to crank the engine for 10-12 seconds, release the gas pedal. The engine should start. The fact is that in this way, by cutting off the fuel supply, you blow air through the spark plugs.

The engine did not start. Then try to dry them. Spark plugs for an injector are, in principle, no different from a carburetor engine. Therefore, we again use the “old-fashioned” method: we unscrew them, clean them from carbon deposits with a metal brush, or a toothbrush, and dry them either with a hairdryer, or on a gas stove or in the oven. We check the gap and screw the spark plugs for the injector into place. The engine should start.

For used cars, the recommendation of experts is to clean the spark plugs more often, or even better, replace them.

If the story of filling the spark plugs with gasoline repeats itself every morning, you need to carry out diagnostics: spark plug quality, injector cleanliness, spark output from the ignition coil, Hall sensor.

Conditions under which the spark plugs will not fill with gasoline

Naturally, these are ideal conditions, but you can control many of them so that you don’t have to meet the morning in a minibus while going about your business.

So, the main conditions are:

• a well-charged battery and a working starter,
• high-quality oil with appropriate parameters for the cold season,
• spark plugs and high voltage wires are of high quality and in good condition,
• the injector nozzles were promptly cleaned and adjusted. Preferably not with the help of various additives to the tank, but with the use of equipment for cleaning injectors,
• high quality gasoline

People's advice: if you want the engine to start normally in cold weather and the spark plugs not to be filled with gasoline, the engine needs to be “twisted” periodically, once a month. Distance 50-100 km. at a car speed of 100-120 km/h and on good fuel.

Or once every two days, while driving, give the engine a load of up to 4500-5000 rpm for 10 seconds so that self-cleaning of carbon deposits and deposits in the chamber occurs.

Fills candles with gasoline: reasons

The injector fills the spark plugs with gasoline due to the characteristics of the engine control unit. It is usually clear why the spark plugs on a VAZ 2110 or any other similar car flood during frosts. Going forward, we can say that the main reason why spark plugs are filled with gasoline is negligence and a discharged battery.

In order for the engine to start in cold weather, the engine control unit needs to supply more gasoline to the combustion chambers, because there is more oxygen in cold air, so more gasoline is needed. As a result, more fuel mixture is obtained, and the car usually drives more quickly if everything works well.

The engine's electronic control unit gives a signal to the injector nozzles to increase the fuel supply. They usually cope with this normally, if they work properly.

But if your battery is far from new, and in the cold the battery discharges faster, then a situation may occur in the engine when the injectors drive gasoline into the combustion chamber, and the starter creates the necessary compression in the cylinders, at this moment a high-quality discharge must appear for it to occur. flash. Also, a lot depends on the quality of the fuel, and high-quality fuel does not exist in nature in Russia.

As a result, it turns out that if the engine has ideal compression, and this only happens in a new car, then the injector spark plugs will be able to start the engine with the minimum permissible impulse. And if the car is not new and the battery has also become weak in the cold, then eventually the spark plugs will give a weak spark, and the injectors will supply fuel to the combustion chamber at full capacity, so the spark plugs will begin to flood, and they will finally stop giving a spark. This is why the injector floods the spark plugs because the battery is discharged. Therefore, if you have flooded the spark plugs in your VAZ 2114, then you know why this happened, and now we’ll find out what to do about it.

Why do spark plugs fill up on a VAZ 2109?

The reason why the injector spark plugs flood is that in winter it takes effort to mix the fuel-air mixture. Cold air contains more oxygen, which means more gasoline is needed. The ECU sends a command to the injectors to increase the fuel supply, and they perform their task. The fuel is fed into the combustion chamber, where it is compressed together with air. After this, a chemical process occurs, as a result of which the fuel-air mixture must heat up. If everything went as it should, then the engine starts, but if some error occurred, something went wrong, then the spark plugs are flooded with fuel

Everything works perfectly in new cars, which is why spark plugs are usually not flooded in new cars. However, the likelihood of such an outcome is much lower for cars with a working starter and a fully charged battery of suitable power. In addition, you should use only high-quality oil, this is especially important in winter, since in cold weather low-quality oil can turn into a kind of clot, and it will not allow the engine to “spun” effectively.

A worn-out engine can also cause spark plugs to flood, since in such an engine the pistons are simply not able to create the pressure necessary for the fuel-air mixture.

The spark plugs themselves and their spark plug wires are no less important. It is important to remember that the “renown” of the manufacturer does not always indicate the quality of the spark plugs, which is why you will have to look for suitable spark plugs either at random or with the help of the advice of a more knowledgeable driver.

Studying plaque on candles

They say that when candles are “flooded,” black soot forms. Let us clarify: it should not consist of inclusions. All metal, in turn, will be covered with an oily coating. Dry carbon looks different...

Oily layer and dry soot

The photo shows two cases. “Our version” is on the right.

We recommend: Step-by-step installation of a towbar on a Chevrolet Niva with your own hands

And soot can also be brown. And it always, in 100% of cases, is formed due to flooding with gasoline.

Dark brown soot

An oily coating, as in photo 1, is, nevertheless, the result of oil ingress. But an oiled candle does not work correctly - it will also be “flooded”.

With regular “flooding,” carbon deposits form, which we see in photo 1 on the right and in photo 2. The rest does not apply to our case.

What to do to prevent candles from flooding

We have looked at the reasons why the spark plugs on the injector are flooded. Now we need to figure out what to do in order to forget about the fact that gasoline floods the candles in cold weather. To do this, a number of preventative measures should be taken before frosts begin.

First of all, you need to monitor the battery charge level. In winter, it is better to equip your car with more powerful batteries. To prevent fuel from flooding the injector, the battery must be maximally charged. Therefore, if necessary, it must be recharged at night.

With the onset of cold weather, special attention should be paid to the quality of gasoline and oil. You shouldn’t skimp on this and it’s better to purchase only a high-quality product that suits the season.

Naturally, you need to monitor the serviceability of the spark plugs.

Clean them regularly and change them on time if they are faulty. The piston group also requires attention. It is responsible for creating compression, so when it wears out, the necessary pressure to ignite the air-gasoline mixture will not be achieved and fuel floods the spark plugs on the injector.

If it is frosty outside, then when starting the engine it is recommended to first load the battery. Then turn it off for a few minutes. Crank the starter and start the engine. If the launch is unsuccessful, then you need to wait about 10-15 minutes so as not to flood the injector, and repeat the launch. It is necessary to check the serviceability of the car before the onset of cold weather. If all components work properly, then there will be no problems starting the engine.

To summarize, the following conditions can be identified for optimal injector operation:

• the starter must be in working condition;
• the battery is fully charged;
• the lubricating fluid must correspond to the season;
• all high voltage wires and spark plugs must be in good condition;
• nozzles must be adjusted and kept clean;
• use only high-quality fuel.

To self-clean the engine, experienced car enthusiasts recommend going out on the highway every month and driving the car at a speed of 120 km/h.

Self-cleaning of the engine occurs due to strong pressure. You can clean the engine by running it in the morning at five thousand rpm for 10 minutes. The effect is similar to driving along a highway.

Monitor the condition of your car, then you will avoid unpleasant situations and save your nerves.

How to act to avoid trouble

There are several recommendations that will help minimize the occurrence of such problems:

• firstly, you need to monitor the battery charge level and periodically recharge it (this is especially true in winter);
• secondly, check the serviceability of the starter and if any problems arise, do not be lazy to go for diagnostics;
• thirdly, fill the engine with only the best quality oil, which is suitable for use in winter;
• fourthly, change spark plugs in a timely manner and inspect high-voltage wires for the fact of their probable failure;
• fifthly, adjust and clean the injector nozzles. This is easy to do - add one of the special compounds that are sold in stores to the tank;
• sixth, use high quality automobile fuel. To do this, refuel at trusted gas stations.

Remember that in the cold season the engine does not like small trips at low speed.

Therefore, in order to avoid problems, it is necessary to drive 50-80 kilometers at a time at least once a month and accelerate the car to 90-110 kilometers per hour (if, of course, road conditions allow).

If this is not possible, then periodically, while driving, increase the engine speed to 4-5 thousand revolutions. This is an excellent method for removing excess deposits and carbon deposits.

Other reasons

In addition to the already mentioned main reason for flooding candles, there may be others:

1. When starting, the crankshaft turns slowly (we are repairing the crankshaft).
2. The malfunction lies in the valve stem seals, which allow oil to pass through (we change the valve stem seals).
3. The injector is clogged, but continues to supply gasoline and fills the spark plugs with it (we clean the injector).
4. Water appears in gasoline (this happens most often in winter, we choose the right brand of gasoline - “winter” or “summer”).

The latter case is also quite common, especially at sub-zero air temperatures. This is due to the fact that gasoline, which has low volatility, has a poor combination with cold air, so the fuel mixture becomes heterogeneous and begins to flood the spark plug elements.

If the candles are already filled, what to do next?

If there is a suspicion that at least one of the cylinders has a spark plug filled with gasoline, proceed as follows:

1. Stop the starter, disconnect the electrical wiring, dismantle the spark plug;
2. Cover the spark plug well to prevent dust from getting into it. Using a starter, rotate the shaft 10-15 revolutions;
3. The candle is dried and replaced.

Here are recommendations developed by car manufacturers. Along with this, there are “people’s councils”:

1. Before performing “step 1” discussed above, the spark plugs can be dried in the engine itself. When the starter is running, the gas pedal is pressed to the floor and air is sucked in through the ramp;
2. To remove carbon deposits, you can use a brush designed for cleaning metal. A regular toothbrush will also work;
3. If the compression in the cylinder is insufficient, changing or cleaning the spark plugs will be useless. Only a major overhaul will help here.

The recommendation that you need to press the gas to the maximum is only suitable for injection, but not for carburetor engines. However, the work of the latter was not considered here. Good luck.

When replacing or reinstalling spark plugs, it is advisable not to overtighten their fastenings. At the same time, an incompletely screwed spark plug will cause damage to all engine systems.

What should a VAZ-2109 car owner do if the spark plugs are filled with fuel?

VAZ-2109 carburetor car owners can solve the problem of “filling” spark plugs in two ways:

1. You can, of course, unscrew one of the spark plugs and buy exactly the same element, fully assembled, in specialized stores or at automobile markets.
2. Take advantage of a more budget-friendly option and solve this problem yourself. This process is quite simple, so every car owner can cope with it if replacing and cleaning the spark plugs is carried out in stages:

• all candles must be carefully unscrewed from the so-called “sockets” and ignited under the flame of a gas burner, holding them with ordinary pliers;
• these elements need to be heated until the metal turns red in order to completely remove carbon deposits and any contaminants;
• after warming up, you need to use fine-grained sandpaper to get rid of the film that forms during the oxidation process around the connectors;
• Then all that remains is to screw the spark plugs into their original place, and the replacement process can be considered complete.

According to many experts, although such a process is considered economical, it will not help to operate thoroughly heated and cleaned components for a long time, since this process quite often damages the candle core, the basis of which is fragile ceramics.
Therefore, if car owners decide on this replacement method, they must understand that, most likely, in the very near future the spark plugs may fail again, and they will have to repeat the whole process again. It is best to immediately buy a new set of components that match the markings and use them for their intended purpose. After reading this article, every owner of a VAZ-2109 carburetor will be able to independently replace the spark plugs, clean and dry them, and, of course, install them in their original place. Such an event will not take much time, and if questions or difficulties arise during the replacement, you can simply watch a video tutorial on the Internet resource, which will further simplify the replacement of failed elements.

Features of starting a car in cold periods

In cold weather, before starting, you must first load the battery, then disconnect it for a while. After waiting a few minutes, you can try turning the starter to start the engine. If you fail to start the car on the first try, then in order not to fill the injector, you must wait a few more minutes. If all preventive measures were carried out in full before the frost, then there should be no problems with filling fuel.

We can list several conditions that are considered optimal for normal operation of the injector:

• presence of a working starter;
• maximum battery charge. The battery is powerful and in good condition;
• seasonal lubricant is used;
• spark plugs and high voltage electrical circuits must be in perfect condition;
• clean, adjusted nozzles are installed;
• The gas tank is filled with high-quality fuel.

There is an opinion among experienced drivers that driving a car along a highway at a speed of 120 km/h promotes self-cleaning of automobile systems, including the fuel system. You can also run the engine at 5000 rpm for about 10 minutes in the morning. The effect is similar to racing on a track.

It is believed that when high pressure is created in the systems, self-cleaning occurs. These measures can only be carried out if the car is in good condition and a significant increase in pressure in the systems will not harm it.

What steps do you need to take to get started?

The question arises, what to do if the car is not old, all systems are in order, but in the cold it refuses to start? When turning the spark plugs out, it turns out that they are wet. As already mentioned, in the cold season, the cause of this phenomenon may be weak compression, low-quality fuel or a weak battery.

Let's look again at the manufacturer's instructions. The book on car operation defines the following algorithm of actions:

1. Turn out the spark plugs.
2. Wipe them thoroughly and dry them.
3. Run the starter for a few seconds.
4. Put everything in place.

Often, car owners clean the injector using various fuel additives. This is not recommended at all, firstly, the quality of the fuel mixture is lost, which negatively affects the operation of the entire piston group, and secondly, the injector should be cleaned using special equipment.

Experienced drivers carry several sets of spare spark plugs with them . The quality of the spark produced depends on the technical characteristics of this ignition component. There is no point in saving on candles, their cost is not that high, and low-quality candles can cause a lot of problems.

Possible solutions to the problem of flooded candles

The manufacturing plant has already foreseen the situation in which the spark plugs splash, and VAZ, for example, has the corresponding instructions in its passport. Basic recommendations for actions if fuel gets on the spark plug, which is called “cold”:

1. Remove the candles.
2. Crank the starter for 15 minutes without spark plugs.
3. Wipe and dry the spark plugs well, then install them in their original place.

There is an alternative, so-called “folk” method. It must be applied even before the spark plugs are removed:

1. Press the gas pedal all the way.
2. Crank the starter for 10 -15 seconds.
3. Return the pedal to its place.

Since at this moment there is no supply of fuel mixture, the spark plugs are purged and dried with air. If all else fails, remove the wet spark plugs and dry them thoroughly. Depending on the conditions, you can dry it over any heat source - fire, gas stove, hairdryer.

Calcination shortens the life of candles, so you should not heat them for a long time. After drying, the gap must be checked; if necessary, the gap is adjusted and the spark plug is installed in its place. If everything is done correctly, the engine should start.

Injection and carburetor spark plugs are practically the same, so the methods used can be used in both cases. If the spark plugs on the injector are flooded in the warm season, diagnostics of the fuel system and the sparking mechanism is necessary. If necessary, it is necessary to replace faulty components. At the same time, the condition of the injectors is checked, as well as the functionality of the Hall sensor.

The main reasons why spark plugs flood lie in non-compliance with the terms of preventive maintenance and technical regulations. Prevention can significantly increase the period of trouble-free operation of vehicle components. Therefore, even before the onset of frost, a number of preventive measures should be carried out:

• Constantly monitor the condition of the battery. In winter, it is generally better to install a battery with a higher capacity than was used in the warm season. With a powerful battery, a number of reasons for allowing fuel to flood the spark plugs disappear. It is best to recharge the battery at night, but in compliance with fire safety rules;
• During cold weather, increased attention must be paid to engine oil, and high-quality gasoline should also be filled, without contaminants. Consumable lubricants must be appropriate for the season;
• You must constantly monitor the condition of the spark plugs. It is necessary to regularly unscrew the spark plugs, remove carbon deposits from them, clean and adjust the gap. If technical characteristics deteriorate, it is best to replace the spark plugs.

Why are the candles wet?

Sometimes a removed spark plug may be wet. This may be caused by gasoline, oil or coolant (antifreeze). Each of these liquids has its own determination methods.

We recommend: Replacing front and rear brake pads on Lada Kalina

Gasoline can be easily identified by its high volatility. By unscrewing the spark plug, the gasoline quickly dries out. Most often, filling with gasoline occurs when starting a cold engine. This can also happen due to incorrect ignition adjustment.

Oil on the spark plug electrodes may appear due to significant wear of the oil seals in the valves. Less commonly, the cause may be wear of the engine cylinder-piston group or breakage of the oil rings on the piston. Any of these faults requires immediate repair.

The amount of oil on the spark plugs can indicate how serious the problem is. When diagnosing, it is best to use a set of new spark plugs recommended by the car manufacturer, since droplets of oil are clearly visible on a clean insulator. The first stage is the appearance of small dark spots from burnt oil. This will not affect the performance of the spark plug in any way, but will indicate that there are still problems with the engine. The next stage of oil entering the combustion chamber will be the moistening of the lower threaded part of the spark plug. This condition of the spark plug will cause popping noises in the muffler at idle. They disappear as the engine speed increases.

Next is coating the end of the threaded part of the spark plug with oil. In this case, a spark may not appear. The result is frequent claps in the muffler.

The last stage is the complete wetting of the candle from below. In this situation, a spark does not form at all. Therefore, a cylinder with such a spark plug does not work. You can find out about this by regular claps in the muffler, which do not stop with increasing speed. The engine starts to stall.

If oil enters the combustion chamber with completely working fuel supply and ignition systems, then its combustion occurs on the electrodes of the spark plug. As a result, the oil does not have time to wet the candle. That's not to say it's good, but it's not too bad either. In this case, droplets of burned oil turn into ash. It accumulates on the electrodes, increasing their thickness. When the engine is running, the ash warms up well. This promotes further combustion of the incoming oil. It is easy to clean, but it is better to do this at the same time as replacing the valve seals. If you remove the ash from the candle, the oil may stop burning. Because of this, the spark may stop jumping, the spark plug will flood, and the cylinder will stop working.

Sometimes “traditional craftsmen” use the following methods to combat flooding of candles: install candles with a shorter skirt or with a higher heat rating, increase the spark voltage by putting on high-voltage tips, leaving a small gap. All these methods are short-lived, ineffective, and are dangerous for the condition of the car.

The reasons for the ingress of coolant may be the following: a poorly pressed cylinder head, a crack in it or in the liner body, a leaky carburetor heating system. As for the last reason, it is typical only for Japanese cars.

In practice, it is difficult to determine whether antifreeze enters the combustion chamber, since when the engine warms up, some holes may close as a result of metal expansion. Diagnostics must be carried out on a cold engine. To do this, you need to start the car for about 10 seconds. During this time, the candles will not have time to heat up and the cracks will not disappear. When the spark plug is removed, the coolant looks like dew drops.

When buying new spark plugs, you should be wary of counterfeits, as they can cause the entire engine to fail. They can be identified by a crooked or uneven inscription, poor-quality processing of the hexagon of the candle, or poorly executed packaging.

Solving the issue in several ways

Radical (cardinal) decision

If the VAZ 2109 is filled with spark plugs, the main question is what to do? And we do the following:

• We go to a car store with an old spark plug for a sample, select new spark plugs in the image and likeness of the old one, and completely replace the entire set
• When choosing, beware of fakes; do not buy too inexpensive candles that also do not have original packaging.
• It is also recommended to take a close look at the new spark plugs and make sure there are no packaging defects, including the design, defects in the electrodes, ceramic base and inscriptions on it
• Defects in the thread or an easily removed or unscrewed O-ring also indicate a fake.
• However, the engine can stall somewhere on the road, far from “civilization” and shops
• If you look from the other side, replacement is an additional expense, and usually very inappropriate
• Let's move on to a more gentle, budget option so that the price does not hit your modest budget

The most economical solution

How to solve the problem without spending money:

• To save money, flooded car spark plugs need to be unscrewed and “heated”; a gas burner or a homemade torch will help with this as a last resort.
• Your task in this case is not just to heat the candles, but to warm them up until red, or at least with fire to completely clean them of carbon deposits, as well as traces of gasoline
• This method has negative sides; many experts claim that after this the candles will not last long, because such heating can damage the ceramic core of the candle itself
• In addition, a matte oxidation film appears on the electrodes, which it is advisable to remove with fine sandpaper

It’s up to you to choose, I’ll tell you, when you are far from the store and, as luck would have it, you need to go urgently, you don’t care about sentiment.

A quick solution from craftsmen

Instructions from folk craftsmen:

• In the absence of new spark plugs at hand, there is also nothing to “ignite” with, then you can use the old, so to speak “old-fashioned” method, which often helps solve this issue
• Flooded spark plugs simply need to be dried using a starter.
• To do this, do the following: depress the gas pedal completely, then rotate the engine for a while, only using the starter
• The influx of fresh air allows the surfaces of the candles to dry out.
• Due to the fully open throttle, gasoline will not flow into the combustion chambers
• After drying, the engine should start, although not on the first try.
• The disadvantage of the “old-fashioned” method is that there is a high probability of completely draining the battery
• And after that, another driver can help you, who will agree to “give your engine a light” from his
• Or a spare battery, but the likelihood that you will have it at the right time is zero
• Now it is clear to the owners of the VAZ 2109 why the candles are flooded, as well as ways to cope with the problem

That’s all, I hope the material in this article will help you out in difficult times, and you won’t get confused; in addition, it’s worth watching the video lesson, since a person perceives and remembers information better through a picture.

The spark plugs are filled with gasoline, what should I do?

There are several options to correct the situation: the simplest is to unscrew the spark plugs from the engine and dry them. After removing the spark plugs, you need to turn the key in the ignition switch so that the starter spins for about 15 seconds, after which you can put the dried spark plugs back in and turn on the engine. This is what the car manufacturer recommends and writes in the operating instructions.

You may also be interested in: Do-it-yourself car body repair before painting

But there is another proven method - if the spark plugs are filled with gasoline, then before unscrewing the spark plugs and starting to dry them, you should try to start the engine using the purge mode.

To turn on this mode, in a fuel-injected car you need to press the gas pedal to the floor and turn the key in the same way so that the starter spins for about 12 seconds, after which you need to take your foot off the gas pedal, and the starter should continue to spin. The engine should start at this moment, after releasing the gas pedal.

It turns out that when you turn off the fuel supply, the spark plugs are blown out with air. If after such manipulation the engine still does not start, then you need to dry the spark plugs. Injection spark plugs are no different from carburetor spark plugs, so you can safely do the same as they have been doing for centuries - they unscrewed the spark plugs, cleaned them of carbon deposits with a metal brush, and therefore dried them with a hairdryer or gas stove. After drying, you can check the gaps and screw the spark plugs back in. After this, the engine should definitely start.

To prevent this situation from occurring frequently, you need to periodically clean the spark plugs or change them on time. If you fill the spark plugs on an injection engine with gasoline every time when they are cold, this means that you need to do diagnostics - check whether the spark plugs, ignition coils, high-voltage wires, injectors and Hall sensor are normal. If all these components are normal, then the question of whether the injector can fill the spark plugs will disappear by itself.

What are candles

Let's look at the device so that you can understand more clearly what we are dealing with:

• The spark plug housing is screwed into the cylinder head
• The insulator material in it is heavy-duty technical ceramics
• From the inside, a central electrode is fixed on one side and a contact rod on the other in the ceramic part of the spark plug.
• And between them there can be a resistor that suppresses radio interference
• Its side electrode is welded to the body

The design differences between the spark plug insulator and the central electrode itself make it possible to divide them into hot or cold:

• Hot candles are distinguished by a large surface of the insulator, which protrudes into the chamber and is heated by burning gases, and the transition zone from the insulator to the outer shell, on the contrary, is small
• Cold ones have an increased heat removal zone, so their working surfaces heat up less
• The heat number expresses the ability to accumulate heat
• Therefore, in order to choose the right replacement spark plug, you need to use an interchangeability table or a proprietary catalog, because the manufacturer has its own catalog system

We are looking for reasons why the spark plugs on the injector are flooded

Both lean and too rich mixtures cause the engine to stall. But the ECU cannot be wrong... The injectors, in turn, may be clogged - everything is clear here. And in cold weather, the valve may not close well due to ice formed.

Gasoline stain on the water

Conclusion: It is advisable to use fuel with zero water content. A carburetor filled with water may simply freeze, and each of the four (six, eight) injectors will flood the spark plugs at startup.

Main list

The main reasons why the engine floods the spark plugs include the following:

• In winter - the presence of water in gasoline;
• The evaporation coefficient must correspond to the air temperature (season). There is “summer” and “winter” gasoline. By the way, the indicated coefficient has nothing to do with the octane number;
• Clogged injectors are the reason for preparing a lean mixture;
• Slow cranking at start-up is also a common cause;
• Faulty valve stem seals contribute to the presence of oil in the combustible mixture.

When adding ferrocene additives, the second reason is aggravated. And they fight the fourth reason by moving to using the “right” oils. The material should not freeze in cold weather.

Oil 10W40 at -30 C

Recommended SAE ratios: 0W, 5W, but not 10W.

How they do it in practice

You can start a fuel-injected internal combustion engine in winter with both winter and summer fuel. It’s just that in the second case the mixture will have to be made leaner. The question is how to achieve this... For example, you can flash a “winter” program. Or do this:

1. Before starting the engine, the temperature sensor is temporarily disabled. Instead, a sensor heated in the hands is put on the plug;
2. We are trying to turn on the starter... The ECU “thinks” that the engine is warmed up and prepares a leaner mixture than it should.

Note that the DTOZh sensor will be attached to the thermostat.

Connector DTOZH ECU, VAZ-2114 car

We recommend: Effective measures to eliminate problems of poor operation of the stove on a VAZ-2114

If the number of sensors exceeds 1, disconnect the one to which two wires go. It is always connected to the ECU.

Fuel with low volatility does not combine well with cold air - the mixture turns out to be heterogeneous. But if the concentration is lowered, the problem is solved.

Why are the candles flooded?

Let's first look at the reasons why the spark plugs on the injector are flooded. To do this, consider the operation of a car starter.

Thanks to the operation of its pistons and valves, a mixture of gasoline and air is supplied to the combustion chamber, which is ignited by a spark generated by the spark plugs. After ignition, the starter turns off. Thanks to ignition, the engine cylinders start working. To successfully start the engine, you need a working starter, a powerful battery and a favorable ambient temperature.

At low temperatures, gasoline does not mix well with air. It is known that frosty air contains more oxygen. An increase in oxygen content requires the supply of more gasoline. The vehicle's electronic control unit sends a signal to the fuel injectors, which increases the fuel supply. Thanks to the starter, compression is created in the cylinders and at the same time a spark is formed to ignite the fuel mixture. But since the compression does not meet the standards and the spark is weak, the incoming gasoline will flood the spark plugs, preventing the mixture from igniting. This is the reason why candles are poured in cold weather.

The formation of a spark is influenced by the following factors:

• Gasoline quality. It should not contain many impurities and dirt, as this will affect the operation of the injectors.
• Engine wear. If the engine pistons are worn out, they do not create the necessary pressure and fuel may flood the injector.
• Quality of candles.
• Quality of injector and carburetor.
• Battery power: You should monitor its charging.

If the compression is ideal, the engine will start even with minimal impulse and fuel fluid will never fill the injector. But only a new car can boast of such compression. If a car, for example, such as a VAZ, is more than three years old, gasoline fills the spark plugs on the injector more often.

How do candles work?

To understand what is happening and why, we need to understand the nature of the phenomenon occurring, and the roots of the phenomenon are hidden deep under the hood:

• The chain reaction that leads to the VAZ 21093 i flooding the spark plugs begins when you just turn the key in the ignition
• When a combustible fuel-air mixture is supplied to the combustion chamber, which consists of a mixture of gasoline and air that entered this chamber through the intake valves. These valves were brought into operation by the starter. Everything is clear here for now
• The spark plug at this point in time provides an ignition spark, which “comes” through the high-voltage wires from the ignition coil
• Then the mixture of fuel and air ignites from a spark, and a small micro-explosion occurs, after which the engine starts, valves and pistons, and all other mechanisms begin to move

Scheme for detecting problems in the ignition system based on the state of the spark plugs

Why is this happening

The operation of injection engines, where the mixture is formed in the volume of the fuel rail, is always controlled by a special controller. The control unit in question is also called “ECU”:

The injection engine will not start without an ECU

The program installed in the unit’s memory constantly determines how many milliseconds each of the injectors should open. The longer the nozzle is open, the richer the mixture is formed. And in winter, at low temperatures, the controller strives to enrich the mixture to the maximum. And then the following happens:

• The concentration of gasoline in the mixture turns out to be maximum, but the temperature of the fuel and air remains lower than typical for the summer period;
• Compression in the cylinder, due to worn parts, may be insufficient;
• If there is carbon deposits on the spark plug contacts, sparking does not occur as the developers expected.

In total, these three factors lead to the following result: the fuel does not burn, but gets onto the spark plug contacts. As a result, sparking stops, and then, when you try to start the engine, gasoline is pumped into the cylinder. Then at a certain moment the fuel detonates.

When the spark plugs are filled with fuel, you can observe the same symptoms on any car. Starting does not occur during starter operation, but the driver will hear popping noises characteristic of such cases (the result of detonation).

How spark plugs work

Before you begin replacing or cleaning spark plugs, you should understand how these elements work. After all, as soon as the driver turns the key in the ignition switch, the “filling” of the analyzed components can begin:

• the air-fuel mixture enters the combustion chamber and passes through the passage channels of the valves;
• the valves, in turn, will be able to open if the starter’s rotational power is sufficient;
• spark plugs produce a spark, which is sent by the ignition coil along high-voltage wires;
• Thanks to the spark, a so-called explosion occurs, which affects each cylinder in turn, which allows the car engine to start.

If a spark does not form when gasoline is supplied, the system will be forced to repeat the entire starting process, and every time you try to start the engine, the spark plugs are filled with fuel. As a result, the wet element simply will not be able to produce a spark, so the car will simply not be able to start.

Why does this malfunction occur most often in winter? Because the air-fuel mixture cools greatly.

And the more the mixture cools, the more difficult it will be for the candle to light a spark, even if it turns out to be fully operational.

Fuel supply and sparking process

When negative temperatures set in, the fuel mixture becomes insufficiently saturated with air; this occurs as a result of an increase in oxygen in the air during frost. Increased oxygen concentration requires increased fuel supply. If the electronic control is in order, then the corresponding command is sent to the injectors and the fuel supply is normalized in accordance with the temperature regime.

When starting, the starter creates compression in the cylinders while simultaneously producing a spark at the spark plug. As a result, the fuel mixture ignites and the engine performs a power stroke.

If the compression is weak and sparking is insufficient, the fuel mixture does not have time to ignite and simply gets on the spark plugs, then starting the car becomes problematic.

Factors influencing normal sparking:

• quality of the fuel mixture. The presence of dirt and large amounts of impurities negatively affects the functioning of the injectors. They simply become clogged with dirty fuel;
• engine condition. Wear of the pistons does not make it possible to create the necessary pressure in the combustion chamber, so fuel, not finding an outlet, begins to flood the injector;
• non-standard or low-quality candles;
• condition of the carburetor and injector;
• battery charge state. A dead battery cannot crank the starter.

Dealing with the consequences

Let's figure out what to do if the candles are flooded. If the motorist is sure that this has happened, then it is worth drying them using one of the selected methods. Most operating instructions for cars with fuel injection systems recommend immediately unscrewing them from the socket with a spark plug wrench.

At the next stage, dry the engine by cranking the starter without spark plugs for about 10 seconds. After drying, we return the spark generators to their sockets and try to start in normal mode.

It is allowed to start the engine with the spark plugs filled with the option of purging the cylinders. In many situations, this option will make it possible to start the power plant without additional removal of parts. Purge of cylinders in injection engines will be carried out by fully pressing the accelerator pedal during startup and cranking the starter for 10 seconds. Next, release the pedal and try to start normally.

It is important to understand that by pressing the gas pedal during purging, the driver opens the throttle valve as much as possible, which stimulates maximum air penetration into the cylinders and ensures drying of wet surfaces.

Even after purging, the engine may not start in some cases. Then you will have to dry the candles by first unscrewing them and cleaning them from carbon deposits in advance. You will need a medium hard brush. To remove moisture, a hair dryer or oven is suitable, after which check the gap between the electrodes.

After such operations, it is worth purchasing a new set of spark plugs, since the service life of the old ones is significantly reduced after calcination. Replacement is usually carried out after 15–25 thousand kilometers, regardless of the external condition. With frequent filling, it is necessary to get rid of the cause that causes it, and not the consequences.