Which is better and installation of engine protection for Lada Priora

The Lada Priora engine is the younger brother of the VAZ-2112 engine. Externally, it is very similar to the engine from Kalina, but much more powerful due to the increased piston stroke. The cylinders retained their previous dimensions. The block is cast from high-strength cast iron and has excellent cooling due to a cooling jacket located along the entire height of the cylinder block, and in order to extend the engine's life, it is worth taking care of crankcase protection.

Shipping and payment

Payment Methods

For more information about payment, see the “Payment” section.

Installing motor protection

Installing armor is not difficult and does not require special skills. If you know how to use wrenches, then you can safely get started. Installing standard protection, which does not require any modifications, will take only a few minutes. Installation of protection yourself should be done on a pit or a lift. It is advisable to take an assistant with you.

Before starting work, make sure there are holes for fastenings. There should be a total of 7 mounting holes (5 in the front and 2 in the back). Installing the protection will not take much time. You should start by securing the corners with four bolts. The bolts should be tightened all the way to avoid vibrations of the pallet during operation. Then make sure that the pallet fits snugly against the bottom of the car; the edges can be folded if necessary.

Given our road conditions and frequent trips out of town, the Lada engine must be reliably protected to avoid puncture or deformation of the engine crankcase and cooling jacket. After all, repairing and restoring an engine is much more expensive than purchasing and installing protection.

Malfunctions: what can happen to a car without protection

The engine protection installed on the Priora performs two functions:

1. Prevents dirt from the road from entering the engine compartment below, which is especially important in rainy weather and winter.
2. Reduces the likelihood of damage to the engine oil pan and gearbox when falling into a hole or hitting hard objects.

Without engine protection, the following negative consequences are possible:

Contamination of the engine compartment, which not only harms aesthetics, but can also cause failure of electronic components and drive belts. Penetration of the engine crankcase or gearbox, which leads to oil leakage, and in the absence of timely measures - to serious damage to the engine or gearbox. Violation of the normal thermal regime of the engine during the cold season due to accelerated air exchange.

Aluminum crankcase guard

Mounting options for different types of protection may differ significantly. Some can be removed and installed when changing the oil in a couple of minutes, while others will require much more time. All other things being equal, it is better to choose the option that will have the simplest and most reliable fasteners. This is where the experience of other owners will come to the rescue. Otherwise, you will have to constantly resort to intricate techniques when removing and installing, so as not to break soured fasteners, which can be extremely poorly positioned. Sometimes there are protections with technological windows under the drain plugs and the oil filter, but more often than not it is easier to dismantle such protection, so as not to have to wipe off the oil that has spread over it for a long time and persistently.

Engine drive mechanisms

A gear-type pulley is installed on the crankshaft, designated by the index 21126. The teeth of the pulley are designed to work with a timing belt, which has a semicircular tooth. To prevent the belt from slipping during operation, there is a small metal belt (flange) on one side. A washer is mounted on the reverse side. A damper, model 2112, is installed on the crankshaft. It is necessary to drive attachments and a generator.

The pulley also has a toothed disk installed on it, which is needed for the crankshaft position sensor to operate. To drive additional equipment - a generator, a power steering pump, a poly-V-type belt with a length of 1115 mm is used, it has the designation 2110-1041020. If there is no hydraulic booster, then a poly V-belt type 2110-3701720 is used, the length of which is 742 mm. If the car has an air conditioner, all equipment is driven by a belt of type 2110-8114096, the length of which is 1125 mm.

Protection installation process

Let's take a closer look at the process of installing engine protection. In fact, the cost of installing protection is low - from 1000 rubles. If you contact the specialists of a service station, then be sure that the installation of protection on your car will be carried out efficiently and in a short time. You will only need to choose what kind of engine protection you would like for your car.

You can also install the Lada Priora engine protection yourself. To do this, you need to place the car on a viewing hole or on a car lift. For tools, you will need a set of socket heads, a torque wrench, and graphite or other similar lubricant. It is quite possible to install engine protection yourself, without involving a large number of workers. The duration of the process of attaching this part is 30 minutes.

Procedure:

1. Remove the standard boot.
2. Remove the nuts and bolts securing the rear suspension arms.
3. Unscrew the front bolts of the brackets that secure the guy wires.
4. Place the rear guard onto the rear arm bolts.
5. At the front, secure the protection to the standard bracket mounting bolts.
6. Tighten the connecting threads securely.

Protection is installed at four points

Please note that the fastening of shields made of different materials may vary. Experts recommend choosing those options that have reliable fastenings

Improperly performed protection for the Priora engine reduces the safety of the car, in particular, interfering with other body elements.

Which is better

The auto parts market offers a huge variety of armor for the Lada Priora engine. Metal (aluminium, titanium and steel) and plastic armor are available for sale. The latter does not have a long service life, so they are in less demand. And, unfortunately, it is installed in basic configurations. But the metal one fulfills its purpose perfectly! Although it rattles when the fasteners are loosened or installed incorrectly. But this is easily fixed.

The thickness of the protection varies from 1 to 5 mm. Withstands impacts from bumps and stones in all weather conditions, protects against dirt getting on the crankcase and gearbox of a Lada Priora with air conditioning. When choosing crankcase protection, you should pay attention to the presence of mounting holes and ventilation of the engine crankcase. Most specialists working at car service stations recommend installing Sheriff engine protection. This protection meets all requirements, has crankcase ventilation and is reliable and durable. Also provides excellent protection for camshafts and gearboxes.

READ Texet 513r how to install the game

Priora engine protection: highlights

Such shields are sheets of pallets that are mounted on the bottom of the car, directly under the engine, so that the crankcase ventilation is open

Considering the state of domestic roads, it is important to take care of securing the Priora engine protection, since otherwise the power unit will wear out much faster. Therefore, many manufacturers make car shields from metal alloys

This part is mounted using special fasteners. The shields do not need to be removed in order to change the oil, because the protection device must have special holes with plugs.

We select and install engine protection for the VAZ 2110 with our own hands

As a rule, every owner of a “ten” is concerned that the engine crankcase protection of the VAZ 2110 injector, to put it mildly, leaves much to be desired. What is standardly installed on a car from the factory?

Only a plastic mudguard that protects the crankcase block from dirt, water, and, perhaps, from a slight touch on a bump. Usually, modifications are made by the vast majority of car enthusiasts, installing a full-fledged system with their own hands that can protect the engine block.

After all, whatever one may say, our roads, even in cities, are not conducive to soft touches; if you run into a pothole, then just be careful and consider the subsequent malfunctions, despite all the skills in driving the car.

Front-wheel drive VAZ (injector) is at risk for the possibility of crankcase damage. The engine mount of the VAZ 2110 is designed so that it is located, as they call it, on an overhang.

This, firstly, leads to the fact that the oil pan is located quite low. Secondly, due to, albeit insignificant, movement of the engine during braking on the brackets, the car “nods” quite easily, and if it hits, for example, a large stone, this can cause serious malfunctions.

Engine oil sump

It is believed that an additional bracket, which can be found quite easily on sale today, can help the motor “hold on” better. Such a bracket holds the engine block in front, but still cannot protect it from impact.

Possible malfunctions during a crankcase impact

1. A significant dent on the oil pan, but without a visible breakdown.

Don't be complacent if you can't see any oil leaks.

It is very likely that the oil breather (also known as the oil receiver) broke off during a sharp impact.

The breather on a VAZ injector is most often made of aluminum alloy or plastic. The breather has an oil intake tube, which is about 5 cm higher than the sump. Therefore, the place where the breather tube broke off may be above the oil level. First of all, in the event of a sharp impact with a visible dent, the engine must be turned off immediately.

Carter with a significant dent

Checking whether the breather has broken off is carried out as follows:

2. Minor dent, no breakdown observed.

It is unlikely that such a malfunction will cause the breather to break off, but the reduced gap between the breather and the pan will greatly reduce the vehicle's capabilities under high loads.

These malfunctions threaten oil starvation, which always ends sadly for the engine. However, the injection car VAZ 2110 from AvtoVAZ, let's be honest, has a rather primitive control system, and the sensors send little information to the control unit.

New oil pan

It is often not enough to fix the error code. Thus, the injector, being a more progressive system, is inferior here to the old system - a pressure gauge, which shows the increase or decrease in oil pressure as the speed increases or decreases.

However, if the sensor indicator light on the control panel does not light up, you can slowly move to the repair site. Remove the pan, straighten it or replace it, and check the breather at the same time.

If the mudguard and pan are broken, and there is a puddle of oil under the car, do not even think about starting the engine. The faster you silence it, the less harm you will do to it. Only tow truck and further troubleshooting.

Which protection to choose

The choice today is quite wide. “Glands” for protection are made from:

It is better to take steel protection with a metal thickness of at least 2 mm. And definitely - with stamped stiffeners. Also, this part must have special technological holes for draining oil and blowing the engine. The fasteners must exactly match the existing holes on the VAZ 2110.

Installation Rules

Usually, when installing a new protection on an injection VAZ 2110, the factory mudguard is left and the fastening is carried out on top of it, believing that double protection will not harm. However, many people prefer to throw away the mudguard, believing that such a “sandwich” additionally collects dirt and also accumulates ice in winter.

Actually, installing the protection yourself takes no more than half an hour, and is done like this:

Removing the mudguard

If you decide to remove the mudguard before installing the “full” crankcase protection on a VAZ injector, doing it yourself is absolutely simple, just:

Regardless of the protection you choose, you can also install the engine mounting bracket (if you see the need for it). This will make driving more comfortable.

Crankcase ventilation system

It is important to note several points regarding the crankcase ventilation system. It consists of the following spare parts: intake manifold, throttle assembly, large and small circle hoses of the ventilation system, air supply hose, exhaust hose, oil separator and oil deflector

In a car engine, the crankcase ventilation is closed. Crankcase gases are released through a separator, which is installed in the cover of the same cylinder head, into the intake pipe. These gases are then sent to the engine cylinders, where they are burned. At idle, gases from the crankcase pass through a calibrated hole in the throttle through a small circle hose.

System ventilation hose

Under engine load, the throttle valve opens slightly or completely and the gases pass through a large circle hose through the air supply hose into the intake manifold, and then into the chambers where they are burned. This is how crankcase ventilation is designed in Priora.

Manufacturers and prices of analogues - list

Engine crankcase protection for Lada Priora is produced by many companies. Below is a list of the most popular models. ALF eco products are manufactured in Nizhny Tagil, a large metallurgical center.

Suitable for Priora:

• ALF.28.11 AL4 – part made of aluminum sheet 4 mm thick. It is attached standardly, the cost is 5800 – 6000 rubles. ALF.28.06 AL4 – made of 4 mm thick aluminum, but fixed to the cross member with clamps. Price – 5000 – 5200 rubles.
• ALF.28.11. AL5 – aluminum, thickness 5 mm, standard fastening. Costs just over 7,000 rubles. ALF.28.06 AL5 – aluminum 5 mm thick with fastening using clamps. Price about 6500 rub. ALF.28.23st – fastening with clamps, material – 2 mm steel. Costs about 1200 rubles.
• ALF.28.060st – two-millimeter steel boot, secured with clamps. Price – 1300-1400 rub. ALF.28.065st – mudguard made of 2 mm steel. Cost approximately 1500 rub.
• ALF.28.11st – steel 2 mm thick, installed with standard fasteners. Costs about 1200 rubles.
• ALF.28.11st – steel 2 mm thick, installed with standard fasteners. Costs about 1200 rubles. ALF.28.06st – parameters are the same as 28.11st, but is attached to clamps. Price - about 1500 rub.

From the range of the ECO brand of the Autofamily company, the model ECO.52.16.010 is intended for the Priora - 2 mm steel, standard fasteners. Price – 2000 rub. Another brand of this manufacturer is NLZ. NLZ.52.16.021 is suitable for Priora, the part is made of steel sheet 2 mm thick, the mount is standard. Cost – about 2300 rubles.

The “AutoStandard” part for the Priora is represented by model 52116. It is made of 1.5 mm thick steel, the price is about 1,400 rubles. Under another brand of this company - MOTODOR - a reinforced mudguard with article number 62102 is offered, the thickness of the steel sheet is 2 mm. Cost – 1700–1900 rubles.

offers engine protection under the AvtoBRONYA brand. These engine compartment boots are offered as original accessories. The following models are intended for Priora:

• 1.06018.1 – fastened to standard places, made of two-millimeter steel sheet. Price – 1000–1100 rub.
• 1.06019.1 – similar to 1.06018.1, differs in increased area. Costs about 1200 rubles.

Aluminum engine compartment protection from this manufacturer is sold under the brand name, article number 3.6018.01. The standard mount is used. Cost – 5500–5800 rubles.

Piterskaya has been selling Sheriff engine mudguards since 1995. Suitable for Priora: 27.1575 without side “wings”, material – two-millimeter steel, price approximately 1300 rubles. 27.1575 with “wings” that provide better protection of the engine compartment from dirt. Price – 1500–1700 rubles.

From the assortment on Priors, mudguard 6612, made of 2 mm steel, is used. Cost – 1200–1300 rubles.

Types of restyled bumpers and their prices

Today, buying a new bumper for a Priora is not a problem at all. The fact is that the VAZ-2170 and its modifications are the most popular model for tuning. Taking advantage of this popularity, a large number of enterprises produce many varieties of bumpers and other body kit elements for Priora.

At the same time, you can buy them either as blanks (unpainted, without seats for additional headlights), or ready-made (painted in the desired color, with spaces for headlights, or with built-in headlights). Here are just a few popular models:

• "I am a robot";

• "Tokyo";

• "Fan" -2;

• "Boxing ring";

• "Ring"-2;

• "Sniper";

• "Strike".

Tuning bumpers can be made of ordinary polyethylene, ABS plastic, fiberglass or fiberglass. Prices for such products vary between 3000-5000 rubles . A stock bumper (catalog number 2170-2803015) produced by AvtoVAZ will cost from 2400 to 4000 rubles .

Types of supports

The Lada Priora has 4 airbags installed on the left and right of the engine, as well as in the front and rear. It should be noted that only engines with 16 valves have 4 supports, while in an 8-valve engine there are only 3 supports.

Right

The right (upper) support is located near the gas distribution mechanism (GRM). Designed to connect the engine to the car body via rubber, to cushion it and dampen vibrations. This support also limits the longitudinal movement of the engine in the engine compartment.

Left

The left support (lower) is installed between the gearbox and the car body. It serves in the same way as the right one to dampen engine vibrations during its operation, as well as to limit its longitudinal movements during movement or work.

Top bar (guitar)

The top support is shaped like a guitar, also called a rod. This support is designed to fix the engine and prevent its lateral movements. Made from metal and rubber. This pillow was produced in several versions from a metal body (on new Prior models) and metal (on older versions).

The upper guitar is located near the right glass of the stand near the support bearing. It is bolted to the glass and on the other side to the engine bracket.

Lower rod

The lower guitar has the same structure as the upper one. It should be noted that the upper and lower supports are interchangeable with each other.

A lower support is installed under the power steering or air conditioning pump. Attach to the beam and on the other side to the engine bracket.

8-valve gearbox support

This support is installed only on 8-valve engines. Attached under the bottom of the car and to the gearbox housing. This support replaces two guitar supports.

Quite often, in order to more reliably fix the internal combustion engine in the engine compartment, such a support, as an additional one, is installed on 16-valve engines.

All the details of the box - what's inside

The five-speed gearbox of the Lada Priora is connected to the central gear and differential. The Priora gearbox consists of shafts: the input shaft is made as a block of central gears. The gears of the forward speed modes have oblique teeth, the reverse gears have straight teeth. They contact the gears of the secondary shaft. There is an oil sump at the bottom of the secondary shaft in the bearing area. It is responsible for distributing the oil emulsion and supplying it to the secondary shaft, and then to the driven gears of all gears. The design of the gearbox includes a gear synchronizer. Synchronizers for 3rd, 4th, 5th gears have a similar design. The only difference is the blocking circles. The parts of 1st and 2nd gears have a different design. They have two cone-shaped friction areas installed, which relieve the load, distributing it evenly among themselves.

There is a magnet in the core of the clutch housing. It attracts metal waste and shavings and prevents its penetration into the system. A mandatory element of the box is the drive. It should be treated with special care. In addition to the listed parts of the box, it contains a jet rod, which is fixed at one end to the motor. Thanks to this, independent gear changes while driving are excluded.

The traction-controlled transmission has a three-arm handrail that activates the selected speed mode. A cable-operated transmission has a cable that activates the desired gear.

The marking is deciphered as follows.

1. XTA is an introductory part indicating the continent, country and car manufacturer.
2. Next, the exact model of the machine is indicated, in this case 217030.
3. The last seven digits indicate the serial number under which the car left the assembly line.

To ensure complete safety and control of vehicles, the manufacturer issues a duplicate number. It is usually located on the right rear wheel arch or near the driver's seat.

Identifiers are located in convenient places and are easy to read. Application using the imprint method eliminates the possibility of falsifying the marking and its damage during operation of the machine.

Basic moments

The engine is reliably protected

Engine crankcase protection is sold in specialized stores. Auto mechanics recommend buying products from these and Sheriff on Lada Priora. These manufacturers provide a warranty on their product. The rigidity of this structure is calculated taking into account the technical characteristics of the vehicle.

The engine for the Lada Priora car was created on the basis of the power unit for 2112. Its volume is 1.6 liters. The cylinder block is made of high-strength cast iron, which gives the structure strength and reliability. The engine cooling jacket is made in such a way that each cylinder is protected from deformation. The top of the system is open. This design has a positive effect on ventilation of the crankcase and pistons of the power unit.

The crankshaft bearing supports are installed at the bottom of the engine. Bolts are used to secure them to the base. The last element is made of cast iron and is protected from movement along the axis by half rings. This part is equipped with counterweights (8 pcs.), which are designed to reduce vibration.

At the front is a pump used to pump out oil and pulleys. On the other side there is a cast iron flywheel. Each working surface of the elements has undergone heat treatment, which significantly increases their wear resistance. The cylinders have 4 valves (2 intake and 2 exhaust). The block head has corresponding bushings with locking rings that keep the last parts from falling out.

The power system of the engine in question includes:

• fuel pump;
• filter;
• throttle assembly;
• hoses;
• injectors.

Selection rules

Engine protection is installed on the car taking into account the crankcase ventilation scheme. It is presented in the form of the following elements:

1. Intake manifold.
2. Throttle assembly.
3. Large and small circle hoses.
4. Exhaust hose.
5. Oil separator.
6. Oil deflector.

The crankcase ventilation system in the Lada Priora engine is open. The gases from the main unit pass through a separator installed in the cylinder head cover and then enter the intake pipe. Gases burn in the engine cylinders. When cold, the elements pass through a special hole (in the throttle) along a small circle hose. Under engine load, the damper partially or completely opens, gases enter the intake manifold. The waste is burned in a special chamber.

The pallet protection is made of steel, aluminum or carbon fiber. The crankcase protection serves as an additional obstacle for intruders who want to get close to the engine compartment. There are 2 types of design:

Two protection options

The cheapest part is considered to be crankcase protection made of sheet steel. The characteristics of stainless steel protection coincide with the descriptions of its aluminum counterpart. The difference (1st unit from 2nd) is only in the original appearance and higher price. The crankcase protection is selected taking into account certain criteria

Creteria

Rules for choosing motor protection

The modern car accessories market is overflowing with offers of inexpensive options for protective shields. You can find samples made of steel, stainless steel and composite materials. Such products have both disadvantages and advantages.

The Priora carbon composite crankcase protection is considered the most practical and reliable due to its high strength, lightness and resistance to aggressive substances. The main disadvantage of such shields is their high cost.

The most affordable option is considered to be the engine protection option for the VAZ Priora, which is made of steel. Such shields perfectly withstand repeated blows, but have a decent weight. The price of such products is low. The protective structure made of stainless steel is comparable in cost to parts made of aluminum alloy. Factory protection that is installed on domestic cars is most often made of durable plastic. Of course, such an accessory cannot fully protect against a strong blow. In addition, plastic debris can deform cooling system hoses, wiring, etc.

The most important requirement for the mechanical properties of shields is that the protection must absorb and absorb high impact energy, which is directed directly at the engine. In addition, it should not itself be intensively deformed and not allow the car body to bend. The design rigidity of the shields to protect the engine must be such that it deforms under any influence only on the size of the space between itself and the engine. On average, this figure should not exceed 3 cm.

In addition to a certain rigidity, the Priora engine protection must have strength that would avoid damage to the engine crankcase when hitting any obstacles

And one more important requirement is the mass of engine protection. The weight of the shields should not overload the front axle of the car, but should also be sufficient to ensure high strength

The optimal weight today is considered to be from 7 to 15 kg.

Materials used to make engine (crankcase) protection for Lada Priora: features

Mud flaps protecting the engine compartment are made from:

Steel

This is a common material for motor boots, the best choice, good price and quality. Sufficient strength is ensured with a thickness of 2 mm; such a part weighs 8-10 kg. The advantages include good maintainability. The main disadvantage is susceptibility to corrosion.

Aluminum

Aluminum is softer than iron; parts with a thickness of 4 mm or more are used as mudguards, but such parts weigh less - from 6 kg. Aluminum parts cost 3-4 times more than steel parts. Their use is most justified in motorsports, where every kilogram counts.

Stainless steel

Stainless steel engine compartment boots are similar in quality to products made from ordinary steel, but are not subject to corrosion. This causes their higher cost.

Composite materials

Modern synthetic materials - Kevlar, carbon, carbon fiber - make it possible to create lightweight, durable parts. Due to their expensive production, such anthers are rarely used. A reliable engine splash guard is the key to preserving the car’s power unit even when operating on bad roads.

Source

Detailed description

Steel protection AutoBronya

• Thickness 2-4 mm.
• Computer 3D modeling technology.
• Technological hatches.
• Stiffening rib.
• Quick installation.

Protections are made using precision equipment. During production, the possible load, force and consequences of the expected impact are calculated. The temperature conditions of the engine are also tested.

Technological holes allow you to change oil and remove dirt without dismantling the product. To increase the reliability of the structure there are stiffening ribs.

Installation takes place in standard places without modifying the vehicle design.

How to replace the crankcase protection on a VAZ 2170-VAZ 2172?

1) Any protection is attached to bolts at the ends of which there are also nuts, so crawl under the bottom of the car and look there for all the bolts (or nuts) that secure it; on the standard protection that is installed on cars from the factory, the nuts for its fastening are located in the front parts of the car (see photo 2, it is attached to the bottom of the front bumper), and the remaining bolts at the end of which there are nuts secure it in the rear part, to unscrew the remaining bolts you will need to hold the bolts themselves from turning with one key, and unscrew them with the other key the nuts themselves are as shown in the photo under number 1.

Basic moments

The engine is reliably protected

Engine crankcase protection is sold in specialized stores. Auto mechanics recommend buying products from these and Sheriff on Lada Priora. These manufacturers provide a warranty on their product. The rigidity of this structure is calculated taking into account the technical characteristics of the vehicle.

The engine for the Lada Priora car was created on the basis of the power unit for 2112. Its volume is 1.6 liters. The cylinder block is made of high-strength cast iron, which gives the structure strength and reliability. The engine cooling jacket is made in such a way that each cylinder is protected from deformation. The top of the system is open. This design has a positive effect on ventilation of the crankcase and pistons of the power unit.

The crankshaft bearing supports are installed at the bottom of the engine. Bolts are used to secure them to the base. The last element is made of cast iron and is protected from movement along the axis by half rings. This part is equipped with counterweights (8 pcs.), which are designed to reduce vibration.

At the front is a pump used to pump out oil and pulleys. On the other side there is a cast iron flywheel. Each working surface of the elements has undergone heat treatment, which significantly increases their wear resistance. The cylinders have 4 valves (2 intake and 2 exhaust). The block head has corresponding bushings with locking rings that keep the last parts from falling out.

The power system of the engine in question includes:

• fuel pump;
• filter;
• throttle assembly;
• hoses;
• injectors.

Installing motor protection

Most crankcase guards are attached in two ways:

To regular places. In the front part - with the help of clamps to the transverse beam of the suspension, in the rear - standard. Before installing the accessory, you need to remove the factory boot of the engine compartment, which will require two “19” and one “10” keys. The mudguard is removed as follows: Unscrew the nuts securing the rear arms, which hold the rear part of the boot. The 5 nuts securing the mudguard in the front part are twisted. Afterwards the roof guard is installed. If it is installed in the normal way, it is enough to install the part in the place removed in the reverse order.

For models with modified fastening, as a rule, the necessary fasteners are included. For installation you need to: Attach the mudguard at the rear in the standard way, installing it under the nuts of the suspension arms. From the front, put mounting clamps on the suspension cross member, insert their ends into the holes in the protection and tighten the nuts. Such fastening is more reliable, but at the same time, as a rule, a smaller area of ​​the engine compartment is covered, and the vehicle's ground clearance - the space between the body and the road - is reduced.

Installing a mesh in the Priora bumper

To protect the lower part of the radiator from fluff, insects and stones, it is proposed to install a grille at the bottom of the bumper. You will need to buy an aluminum mesh at the car market (commonly called a bumper protection mesh). Next, remove the Priora bumper. We apply the mesh and make folds along the entire perimeter.

We cut off pieces of mesh of the required size with ordinary scissors.

There are different ways to attach the mesh to the bumper. In this example, it was decided to secure the mesh with hot melt adhesive. As it turned out later, this method of fastening is not entirely reliable and the grille fell off over time. A more reliable installation method: plastic clamps, self-tapping screws, or epoxy glue.

Install the bumper and grilles in reverse order.

Improvement of the Priora radiator grille

Installing a mesh in the upper radiator grille will protect the top of the radiator. We adjust the mesh to the size of the grille and fasten it with self-tapping screws.

Install the grille in reverse order.

Installing a protective mesh in a restyled bumper

You will need two meshes measuring 1mx0.15m. We remove the bumper and secure the lower mesh with clamps. Self-tapping screws will not work here, because they will go right through the plastic.

Regular places for the mesh were found in the upper part, but they were not enough for reliable fastening, so self-tapping screws were used. There is no need to be afraid here - there is a distance between the outer grille and the inner one (where we turn the screws).

It is better to buy black clamps in advance, or paint them over with a black marker. This design holds up very well.