Wheels for VAZ 2114: sizes, advice from experienced people on choosing

The AvtoVAZ company took an important step for itself when it decided to restyling the legendary “Nine”. This is exactly how the VAZ 2114 appeared, which was produced in almost a million copies over the entire period of its production.

The uniqueness of the car is that it is literally created for tuning. Of course, the manufacturer didn’t do this on purpose, but it turned out more than successfully.

But if you don’t want or can’t spend a lot of money on tuning and modifications, there is a simple and budget option - install new wheels on the VAZ 2114.

What kind of drilling is on the VAZ-2114

One of the main parameters that you should pay attention to when replacing standard disks on a VAZ-2114 car is the dimensions, location and diameters of the mounting holes, PCD, pitch circle diameter, or, in simple terms, drilling or bolt pattern.

Bolt pattern on a VAZ-2114 wheel

Bolt pattern - this characteristic is expressed in two numbers and indicates the distance between the centers of the mounting holes and their number.

Drilling for all VAZ cars (except Oka and Niva) - 4x98 , four holes, the centers of which are located at a distance of 98 mm from each other .

However, this is a simplified designation for the user. The disc manufacturer is required to take into account both the diameter of the holes, their number, the distance between their centers, and the diameter along which the centers of the holes are located . Such a designation would complicate the selection of disks by the user, so knowing drilling in the “number of holes/distance between them” format is considered sufficient.

A few more wheel parameters

The drill bit can be measured using the spare wheel. In all SAMARA drilling 4*98

There are several more parameters that relate to the original VAZ-2114 rims - the width of the stock rim is 5.0J , the offset of the ET45 , the diameter of the centering hole at the hub is 58.5 .

Video

Beautiful wheels for VAZ 2114.

In this video there is a selection of alloy wheels for VAZ cars.

Top 10 tips for choosing car rims.

This video shows how wheel size affects fuel consumption using the example of a Subaru Legacy 2.0R AT.

How to choose tires.

Share your experience, who installed which discs and what the result was.

Author of the publication

offline 7 days

Decoding indicators on disk

It will be easier to select car wheels when the decoding of the provided indexes is known, and therefore special care is required to consider the details in this matter. It is imperative to remember that each designation is placed for a reason and has its own information load.

For example, 175/70 R13 is considered a standard option, so it needs to be considered in particular detail. This means that the diameter of the tire is 13 inches, the profile height in percentage is 70, and the width in millimeters is 175. This allows you to figure out in detail whether the tire is suitable for fitting a car. Based on this, a disk is selected that fits perfectly into the geometric proportions.

Nuances of choice

Today, choosing new wheels for the fourteenth Lada is not difficult; to do this, you need to decide on your personal preferences and know some parameters:

hub diameter – 58.5 mm;
width – 5-6.5 inches;
bolts standard – M12;
thread pitch – 1.25 mm.

VAZ 2114 car owners can purchase for their car:

stamped (steel);
cast/forged alloy wheels.

Everyone chooses for themselves which models are more suitable for them in terms of road complexity and budget.

Varieties

Selecting new wheels for a VAZ 2114 is not an easy task. When choosing them, it is important to take into account a number of parameters, plus combine them with personal preferences.

As for the dimensions, the emphasis should be on the diameter of the hub (58.5 millimeters) and its width (5-6.5 inches). For fastening, standard M12 bolts are used, the thread pitch of which is 1.25 millimeters.

We recommend: Why the window regulator of the Lada Priora does not work

As with most other cars, the VAZ 2114 is offered on the market:

Steel (stamped);
Light alloy (divided into forged and cast).

Stamped

Steel wheels are very common. Not surprising, because all “fourteenth” models are equipped as standard with exactly these types of “rollers”. However, they are popular not only because of this. These wheels are cheap, but at the same time reliable and durable.

When impacted, they do not shatter into pieces, unlike some other disc materials. They just get deformed. Such deformations are sometimes removed manually, although the best option is to use special equipment.

But they also have disadvantages, including:

Large mass, which negatively affects control, fuel consumption and tire wear;
Weight also affects the chassis and transmission;
Steel ones extremely rarely have an attractive appearance, which is one of the main reasons for replacing them with analogues.

Cast

Many car owners prefer to use alloy wheels on the VAZ 2114. This is due to a number of advantages that they carry.

They have less weight compared to stamped analogues.
Helps extend the service life of vehicle components and components.
Have a positive effect on reducing fuel consumption.
Cools the brake system more effectively.
They have a wide range of different designs that can become a real decoration for the entire car. It is enough to put the casting on the car and it will instantly transform. A simple but effective way of external tuning.

As for the disadvantages, they also exist:

Alloy wheels do not bend under strong impacts, as happens with stamped rollers. The situation is worse - a split is occurring. This leads to increased danger during accidents and high-speed movements;
The side surfaces begin to oxidize over time. This requires increased attention and periodic maintenance;
The cost of alloy wheels is noticeably higher than the price of steel counterparts.

Forged

Forged wheels, which are gaining popularity, are also perfect for the domestic modernized “nine” represented by the VAZ 2114.

Strengths include:

High level of strength that matches stamped discs and even exceeds them in some places;
Lightweight design, which is not inferior to alloy wheels;
External attractiveness of forged products;
High levels of rigidity and reliability. With strong impacts they bend a little, even less than steel ones;
The surface is not very susceptible to corrosion, so you don’t have to care for them as carefully as cast ones.

The only drawback of forged kits is their high price. If your budget allows, and such a purchase is really justified, put your VAZ 2114 on forged wheels.

Forged

VAZ-2114 bolt pattern: selecting wheel rims

For several years in a row, forged wheels have been in constant demand. Their dimensions are perfect for a modified VAZ 2114.

Advantages

Several advantages can be highlighted:

Very high strength. They are superior to stampings in all respects.
Light weight, approximately equal to the weight of light alloy models.
External attractiveness.
They are characterized by high rigidity. They are considered very reliable, with a sensitive blow they only bend a little. Moreover, steel products are deformed much more strongly.

Forged wheels never rust. They do not require careful maintenance like their cast counterparts.

How to install a 4x100 disk on a VAZ-2114

Most older foreign cars have a 4x100 drill. This makes it possible to diversify the choice of disks almost indefinitely. However, we must take into account that simply installing, without modifications, 4x100 wheels on a 4x98 seat will not lead to anything good. The fact is that the tolerance in the manufacture of the disk does not exceed 0.7-1 mm . That is, it is theoretically possible to put on a disk with a 4x100 fit, but this will lead to the fact that only one bolt out of four will fit exactly on the cone. The remaining fasteners simply will not tighten all the way and, as a result, the disk will sit with a distortion that is almost impossible to check by eye.

Disc with bolt pattern 4*100

The disc will not fit with its mating plane to the hub, and this will lead to the fact that it will have a runout.

Systematic runout can not only lead to the fact that the only bolt that is tightened correctly will quickly become loose, but also to instant wear of the wheel bearing, and the remaining bolts will loosen on their own. There is a way out of this situation.

Disc runout leads to rapid wear of the wheel bearing

To install a disc with a 4*100 bolt pattern, you need to either install a spacer or install studs with nuts instead of bolts.

A less reliable option is to install bolts with an offset head. A not entirely correct option is to install studs, for example, from the cylinder head and nuts from Niva, but the studs are not designed for torsional force, so the most reliable option would be to install spacers. You can carve them yourself or buy them ready-made.

We recommend: How to replace the radiator of a VAZ 2107 stove

But here you need to take into account several nuances:

The width of the spacer must be at least 20 mm, since only in this case we will ensure proper thread strength.
In this case, the offset of the disk will increase by the same 20 mm, which must be taken into account when selecting a disk.
In this case, the disc must be selected with a minimum offset in order to remove the load from the hub and somehow compensate for the difference in offset.

Installing studs with eccentric nut

Stamped

This type of wheels is considered the most common. The basic equipment of many AvtoVAZ models is equipped with this type of disc. They are characterized by low cost, durability, ease of installation, and maintainability. Upon impact, the structure does not crack, break or fly into pieces, but simply bends/deforms. Any malfunctions are eliminated using special equipment or manually.

heavy weight, which increases tire wear, fuel consumption and negatively affects the condition of the suspension;
not a very attractive look.

Factory standard options

On the VAZ conveyor, stampings with a diameter of 13 inches (1 inch is 2.5 centimeters) are installed on the VAZ 2114 model. Tires installed, as a rule, are not expensive, with a high profile.

For tuning enthusiasts, there is a lot to work on with such a basic option, because there is room to change the diameters of the rims and the height of the tire profile. One of the options for tuning a VAZ 2114 is to install wheels with the most suitable wheel diameter and minimum tire profile height.

On the VAZ 2114 you can install wheels with a diameter of 15″,

but you will have to install low-profile tires and you can install 14″ (14 inch) wheels and a tire width from 5″ to 6″. This is clearly written in the LADA VAZ 2114 passport.

What tires can be installed on 14″ wheels?

For such wheels, only two tire markings are suitable:

185/60 R14. This size is preferable.
175/65 R14.

Replacing standard wheels provided by the manufacturer with 15-inch ones may prevent you from passing technical inspection. Because the car's passport states that it is not recommended to install wide wheels on this car. This is what a four looks like with 15 wheels.

Calculation, index, code, marking

Few people understand codes and markings. So, for example, the designation with the Latin letter R means radial, and the number that is stamped after R means the diameter of the disk.

You can calculate the parameters of wheels and tires with your own hands, or rather with your own head.

Let's start deciphering the tire markings. For example, let's take the factory tire designation for the VAZ 2114 - 175/70 R13:

175 is the width in millimeters;
70 - height of the rubber profile in relation to the width in percent;
R13 is the tire type - radial, and 13 is the diameter in inches.

Anyone who wants to learn how to drift with front-wheel drive in the summer, do not forget to prepare the car: wide tires forward, narrow tires back.

Calculation of rubber profile height

To calculate the height of the rubber profile, you need to multiply 175 mm by 0.7 (this is 70% divided by 100). The profile height is 122.5 mm.

You can decipher a car’s VIN code yourself, or you can use online services.

Calculation of diameter (conversion from inches to cm or mm)

To find out how many centimeters in diameter the disk is, you need to multiply 13″ by 2.54 cm = 33 cm = 330 mm.

Calculation of the total wheel diameter (disc + tires)

122.5 + 330 = 452.5 mm. This is the factory size for the “four”.

The recommended wheel sizes for the VAZ 2114 are R13 and R14.

The car's passport indicates what size wheels can be installed on this model. These are: R13, R14.

If you install 15-inch wheels on this car and tires that are not low profile, then on bumps during shock absorption the rubber treads will touch the wheel arch liners or the wings themselves.

If you still decide to install R15 wheels, then you need to choose the following tires:

185/55 R15;
190/50 R15 (this option needs to be checked to see if the width is suitable or not).

Classification of disks by manufacturing method:

Stamped. The simplest and most common method of making wheel rims.

The steel sheet is pressed into a given shape. Hence the name “stamping”. The cheapest way to produce parts of various shapes. They can also be improved by painting. For example like this:

Or like this:
Repairable. Since they do not crack, they can be straightened to their original shape.
Cast. Manufactured by casting.

slightly, but reduce fuel consumption;
tires last longer;
variety of shapes, which makes them popular among fans of tuned cars.

Flaws:

high price;

fragility - such discs burst under sudden strong impacts.

Forged. Manufactured by forging.

And this is a Lada Priora with forged white wheels.

They have all the advantages of stamped and cast wheels. They have one mine - a very high price. Forged wheels are manufactured by VSMPO.

Classification of disks by manufacturing method

Wheels for VAZ 2114 cars can be manufactured using different technologies, so before purchasing it is important to consider all the options available:

Stamped. This is the most common option, which combines various technical and practical features. Low cost combined with high quality are the main advantages that made the products popular in the automotive market for the VAZ 2114.

Among the advantages of stamped discs, we can highlight such qualities that have become the basis for the development of wide consumer interest: due to their softness, such discs are smoothly deformed, so the driver will not encounter unexpected cracking of the disc while driving; Considering that the discs do not burst, but bend, they can be easily restored.

Cast. You can even more often find cars on die-cast ones, since they are the personification of durability, reliability, quality and attractiveness. But you will have to spend a lot of money on such a model, since, taking into account the peculiarities of the technological process, the cost increases significantly.

The high cost makes such wheels not affordable for every buyer, but you can count on the following positive aspects: low weight, which makes the car easier to drive;

We recommend: Changing the engine oil

fuel consumption is slightly reduced; there is a large assortment of shapes to choose the most attractive option; The integrity of the tire is preserved, as it is protected from negative external influences.

Forged. Such discs are created by mechanical forging, so they have a solid structure. As a rule, these are white models with characteristic stylistic features.

Photos and technical characteristics of each option are an opportunity to choose the most attractive and high-quality type for equipping your vehicle.

Peculiarities

For the fourteenth Lada model, there are several wheel options, the choice of which for a long time depended on the vehicle’s configuration - luxury or standard.

At the beginning of the production of the new model, the manufacturer decided not to offer a wide range as he considered that the car was budget and its owners would not spend money on additional, expensive accessories. Therefore, the VAZ 2114 was “put” on the usual “stamping”, which for more expensive representatives were equipped with special decorative caps.

In 2009, when the restaling was carried out, the range of wheels expanded greatly and was replenished with simple and complex “castings”, which were included in the luxury package.

Installation of non-factory wheels on a VAZ

If you want to install a wheel rim of a different design on a VAZ car, you should pay special attention to the offset value. The conventional marking of this value indicates the distance from the plane of contact of the wheels to the conditional center of the rim. This indicator is measured in millimeters.

The most suitable one can be called the ET36 departure. Of course, the PCD, or more precisely the diameter of the circle on which the wheel rim mounting holes are located, must be in accordance with factory requirements.

On VAZ-2114 cars, this value is 98 millimeters. In technical documentation, this parameter is noted as PCD = 4 × 98 millimeters, this is the bolt pattern.

The optimal ratio of the width of wheel rims, the bolt pattern of which is 4×98 mm:

175/65R14 – wheel width 5.5J;
185/60R14 – 6J;
185/55R15 – 6J;
195/60R1 – 6.5J.

You can change the wheels on a VAZ car yourself. For many Russian car owners this is not a problem. But if there is no practice, there is no need to rely on resourcefulness and ingenuity. The brake and disc systems of any car do not tolerate amateurs, since human safety is at stake.

From time to time, it is better to carry out diagnostics using certified equipment, and you can change the brake pads yourself. Moreover, such work is not carried out often.

Wheel rims can last approximately 40 thousand kilometers. However, if the owner takes good care of his own car, then this period can be extended to 100 thousand kilometers. The size of rims for VAZ cars, as well as their type, is at the request of the owner. The most important thing is that the choice of wheel rims should not contradict the characteristics specified by the manufacturer. So, when visiting an auto parts store and buying new rims, all of the above must be taken into account.

Causes and consequences of damage

Driving on poor quality roads in Russia forces car owners to look for a new windshield at least once every year and a half. Even a very small pebble flying from under the wheels of a car can lead to damage to the part.

There are two types of damage:

Chips. If only a chip appears on the surface, the driver is lucky. This means that the first layer is damaged; it is not necessary to install a new spare part.
Cracks. You can't hesitate. At any moment, glass can crumble into pieces due to a hole in the road, and this will lead to an accident.

What can you do

If the driver fails to change it in time, there are several popular tips:

Using a glass cutter, make perpendicular cuts 0.5 cm long along the edges of the “web”.
Drill small holes with a thin diamond drill bit. The work requires accuracy, patience and attention.
“Weld” the crack. It's better to contact specialists. Without experience it will be difficult.

A little history

AvtoVAZ has prepared several wheel rim options for the “fourteenth” model. The installation of one or another depended on the configuration - standard or luxury. The manufacturer did not specifically offer a wide variety, since he understood that for such a simple car, buyers are unlikely to want to spend extra money on additional options.

After the planned restyling of the VAZ 2114, which took place in 2009, the range of wheels available for the model was replenished with cast sets. Of course, they were the prerogative of the luxury package.