A smaller percentage of ultraviolet radiation penetrates through tinted glazing, reducing the likelihood of being blinded by the headlights of oncoming cars and eliminating distortion of vision due to glare. Fully tinted windshields are prohibited by law, but sticking a special stripe on the windshield in accordance with GOST is allowed. Refinement of car glazing is carried out according to the rules, if you do not follow them, you can get a fine at any time. With the help of lawyers, we carefully studied the laws and in this article described how to comply with GOST and not receive a fine when sticking a stripe on the windshield!
Stripe on the front glass according to GOST
A stripe on the windshield according to GOST cannot serve as a basis for imposing a fine. Compliance with technical regulations in controversial situations will help prove to the traffic police inspector the legality of tinting.
Standards
The strip on the windshield according to GOST 2022 should be:
- Strictly up to 14 cm wide. This applies to all parts of the sticker, taking into account the bending of the triplex;
- Pasted only from the inside;
- Made from non-mirror materials.
Compliance with the requirements is mandatory regardless of the make of the machine.
To size
According to technical regulations CU 018 of 2011, number 877, the width of the tint strip on the front window of a car in its upper part should be no more than 14 cm, regardless of the measuring point. Failure to comply with this requirement results in a fine of 500 rubles. If such a violation is detected again, the responsibility will be different.
By light transmittance
At least 70% of sunlight must pass through the windshield. However, the tint strip on the windshield, located in its upper part, can have any degree of darkness. It is allowed to have images on the feed.
Criterias of choice
The tint strip on the windshield of a West and cars of other brands can easily be applied independently, that is, without going to a car repair shop. However, you must first choose it correctly; the ease of fixation and compliance with GOST standards will depend on this. The easiest option is to purchase a standard tape, to which there will be no complaints from the traffic police.
Note! In professional auto repair shops, darkening and gluing stripes on glass are carried out strictly in accordance with the standards.
Ribbon color
Car owners often choose tapes in dark shades or tones that match the color of body parts. The stripe can be yellow, red, green or even a combination.
Mirror tape
Direct gluing of mirror-type film is not prohibited by technical regulations. But, according to the rules of the Customs Union, gluing material that does not transmit light to the windshield is unacceptable. The ban is primarily due to the fact that there is a risk of headlights reflecting from such a coating, which can lead to dazzling other road users.
Application of athermal film
The “Chameleon” athermal tape differs from the standard one in that it does not darken, but only prevents some sunlight from entering the interior. Its throughput is 70-75%, and such tinting of the windshield with a strip is not prohibited according to GOST.
Athermal tape reduces heating of the interior and, accordingly, saves fuel, which in hot weather is required to operate the air conditioner. In addition, such stripes on the windshield protect the upholstery from fading.
Necessary materials
In order to stick a tint strip according to GOST, you need to have the following materials:
- film in the size of 200 cm minimum (how much you need exactly, it is better to measure in advance);
- rubber spatula;
- soap solution;
- spray;
- sharp stationery knife;
- technical hair dryer;
- clean rags.
Once you have all the necessary materials, you can begin preparation.
Necessary tools and materials for window tinting
Rating of the best films
Sun protection strips for windshields are produced by dozens of companies from Europe, the USA, and Asian countries. You should buy tapes only from those manufacturers who guarantee the quality of their products and are popular everywhere. Little-known companies often make tinting stickers from low-quality plastic, as a result of which they can distort images, stick poorly and quickly lose their original appearance. The ranking of the best companies producing windshield stripes includes the 5 listed below.
Llumar
Llumar brand film is a product of Eastman Chemical. The service life of the brand tape is at least 5 years. The Llumar brand produces metallized, fade-resistant models; there are accessories not only for the windshield, but also for the side ones.
Windshield tinting with a Llumar strip has several advantages :
- High UV resistance;
- The width of the tape corresponds to GOST;
- No turbidity;
- Prevent glare from headlights at night.
The disadvantages include high sensitivity to burning, so use a hairdryer when applying this brand of tape carefully. Counterfeits of this brand are often found in Moscow.
Armolan
Armolan film is produced in the USA. The accessory has a metallized layer, due to which the tape can withstand any contamination and high humidity. The Armolux brand film series belongs to the premium segment, as it blocks up to 99% of harmful ultraviolet rays.
The advantages of stripes on the windshield of the Armolan brand are:
- High elasticity, ensuring ease of gluing the tape;
- Possibility to choose an accessory by price, including luxury;
- One way visibility.
The disadvantage is the rapid fading and the hazy effect in the sun.
H3-ASWF
ASWF films are produced by the US corporation American Standard Window Film. According to the manufacturer, the tint blocks more than 99% of harmful ultraviolet radiation and reflects at least 78% of the sun's light. The tapes have an anti-reflective layer and several levels of light transmission. The glue used is absolutely transparent, which eliminates distortion. The outer surface is coated with Dura-Slide for a smooth, scratch-resistant finish.
Advantages of ASWF stripes on the windshield:
- Ease of fixation;
- Wide range of colors;
- No distortion;
- High degree of protection against damage.
drawback – the price is too high.
Suncontrol
Tinting with accessories retains up to 75% of solar heat, thereby reducing interior heating in summer. The Suncontrol brand produces metallized and athermal options, two-layer tint strips, and films with protection from infrared and ultraviolet rays.
Pros of Suncontrol models:
- No burnout for at least 3 years;
- A wide range of;
- The presence of a finishing coating that protects against scratches;
- High quality - there are practically no defects in lots of accessories purchased directly from the manufacturer.
The downside of Suncontrol tinting tapes is their high price; products with black spots cannot be ruled out.
H3-Global
Tinting the upper part of the windshield according to GOST is possible when using H3-Global brand products. This brand produces two-layer films made of polyester with a metallized layer. The shade of the tape resembles charcoal or can be graphite greenish.
Advantages of H3-Global films:
- High degree of UV protection;
- Protection of the interior from heating;
- Long-term preservation of film shade;
- Ease of molding.
Basically, H3-Global products are used on expensive cars, since their price is high.
Why car stickers?
Car stickers on German self-adhesive film are tens of times cheaper than airbrushing of the same size. For example, vinyl printing on a hood costs about 5,000 rubles, but for airbrushing you will have to pay a much larger amount.
We make custom car stickers, and you can transfer any high-quality image in digital format to the film - just find the picture on the Internet, download it and send it to us. The flight of fancy is not limited - there are billions of images on the Internet today, and almost any of them can decorate your car.
If you feel like an artist, you can draw a picture for a sticker yourself or take a photo and send it to us to make a sticker for your car. And then your car is guaranteed to be different from all others.
To place a sticker on a car, no special knowledge or skills are required. Just read the instructions “How to glue stickers on cars?” and watch video materials in the corresponding section of our website.
Rain, snow, heat and bad weather are not scary for stickers. If the sticker is glued correctly, then even multiple passes through the car wash will not harm the quality of the image. At the same time, removing the sticker will not be difficult. Using a regular household hair dryer makes removing the sticker much easier.
The stickers retain their color saturation for a long time and are guaranteed to stay on the car for at least five years.
But that's not all!
How to properly tint the top of your windshield
Traffic police inspectors have the right to peel off the strip on the windshield if they determine that it does not comply with the standards. This can be excluded if the tinted strip on the windshield has acceptable dimensions. The dark stripe on the windshield of Priors, like on other cars, is glued according to rules, compliance with which will prevent the accessory from peeling off and the formation of bubbles and cloudy spots.
Tools
Tinting the windshield visor according to GOST will not cause any difficulties if you first prepare all the consumables and tools that may be needed during work:
- The film itself. Its dimensions should correspond to the width of the windshield, to which 3-4 cm are added from each edge;
- Spatula made of rubber or soft silicone;
- Soap solution placed in a spray bottle;
- Stationery knife;
- Clean soft rags;
- Technical hair dryer.
Preparation
At the preparation stage, it is necessary to thoroughly wash the glass with soapy water or car shampoo. It is advisable to degrease the place of the sticker itself, that is, the upper part. Then the glazing is thoroughly dried with a hairdryer. The prepared clean surface should not be touched with hands.
Materials
The tinting strip on the windshield according to GOST involves gluing a film that:
- Does not distort the image - the clarity of the material should be such that the stars in the night sky are clearly visible through it;
- Has a shade that does not change when exposed to light;
- Shows stability when molded.
The measurement of the strip on the windshield according to GOST is carried out before gluing it, since otherwise, if the size does not match, the film will have to be peeled off.
Requirements for performing the work
The tint tape should be applied in a dry garage. This cannot be done outdoors, as it is possible that small debris will get under the glue, which will lead to deformation of the accessory. It is better to carry out the work wearing fabric gloves, this will prevent any skin oil from getting on the clean glass.
Step-by-step instruction
After preparing the car, tools and space in the garage, cut a strip of the required width (not forgetting about 3-4 cm allowances at the edges). The sticker is applied in stages:
- The rear view mirror is removed;
- The protective layer is removed from the tape;
- The strip is brought to the glass and smoothed from the center with a spatula or soft rag;
- An incision is made with a stationery knife at the place where the glass is attached;
- Excess parts of the tape are cut off.
The items listed above are required. Additionally, on the hood side, the glass can be heated with a technical hair dryer, this will ensure better straightening of the strip and improve its adhesion. After 5-6 hours you can put the mirror back. Drying completely occurs within 48-72 hours, during which time all stains and areas of cloudiness should disappear.
Note! Installation must be continuously monitored, maintaining a 14-centimeter offset from the top edge.
DIY glass tinting
Since car tuning is not cheap, many owners prefer to do it themselves. To work they will need:
- quality material;
- soap solution and spray bottle;
- rubber spatula;
- sharp knife;
- lint-free napkin;
- hairdryer
Before starting work, it is necessary to dismantle the windshield of the VAZ 2115, although not everyone does this; in principle, you can glue the film right away. If the glass remains in place, then the seals should still be removed. To stick the strip on the top of the windshield, you also do not need to dismantle it. The surface is thoroughly washed, paying special attention to corners and places where more dirt collects. After degreasing, wipe dry with a non-woven lint-free cloth and check to see if there is any dust left.
Spray the surface with a solution from a spray bottle and apply a pre-cut film blank, gradually separating the transparent layer. When the film is placed on the glass, movements from the center to the edges begin to remove air bubbles, as well as excess water. In this case, use a rubber spatula or your own hands.
If the glass has a curved shape, it is advisable to use a hair dryer. With its help, the film can be given the desired shape, and the pasting will be of better quality.
When the tint is applied, the protruding edges are trimmed. A sharp knife is held at an angle of 30 0, while acting slowly.
How to remove tint film
If the permitted strip on the windshield requires replacement or does not comply with GOST, then it should be removed. This can be done hot or cold. The first involves using a hairdryer. Warm up the work surface with a stream of hot air and carefully remove the tape, picking it up from the edge with a sharp thin knife.
When choosing the cold method, first the strip must be soaked with a soapy solution. In both cases, at the final stage, the glass is degreased to completely remove the glue.
Preparation
It is more advisable to carry out all work in a room with low humidity. If there is none, and the procedure will take place outdoors, then wait for warm and windless weather. Moisture that gets under the tint will cause streaks and peeling. The car needs to be washed and the areas where the film is applied should be treated with a soap solution. In difficult cases, you can use a special car shampoo or degreaser for smooth surfaces. Afterwards the glass must be dried with a hairdryer. Do not touch the clean surface with your hands or other objects, otherwise greasy stains may appear.
Penalty for incorrect stripe
The sun strip on the windshield protects the driver's eyes, increases confidence on the road, and reduces the heating of the car. Such glazing improvements are not prohibited, but only if they comply with the law. Otherwise, a fine will be imposed.
Cause
The fine is imposed due to non-compliance with GOST, which defines the standards for gluing tint tape. They are given in document TR CU 018, number 877 of 2011.
Size
The fine for the first time a violation is detected is 500 rubles. It’s better to pay for it right away - there is a 50% discount in the first 20 days.
Car enthusiasts' expectations
So, when deciding on tuning a VAZ 2115 with your own hands, the owner assumes that he will receive:
- protection of personal space from prying eyes.
- protection of interior parts from exposure to sunlight (the parts heat up 60% less, which means they do not emit harmful substances, and the paint does not fade).
- Reducing glare from headlights of oncoming cars and reflections from snow.
- protection during a possible accident from crumbling small glasses.
In order for these expectations to be fully met, you need to carefully select the material, having first studied its features. It is also worth paying attention to the fact that it is not advisable to have the transparency coefficient of the film below 85%, otherwise the car owner may be fined.
