Self-replacement of LEDs in the turn signal of a Lada Vesta mirror

Cars of the Lada Vesta and Lada XRAY family are equipped with turn signal indicators. The first model has pre-installed LEDs, the second has standard incandescent lamps.

According to the manufacturer, the turn signal repeaters are disposable; if the diode burns out, the unit must be replaced as a whole (assembled). However, craftsmen have found other ways to replace diodes at minimal cost.

Step-by-step instructions for replacing the turn signal in the Lada Vesta mirror

1. We place the car within the perimeter of the repair area.
2. On the driver's side we snap off the plastic housing with the speaker.
3. Unscrew the screws.
4. Disconnect the terminals with the wires.
5. Remove the mirror assembly.
6. Let's break it down into its component parts.
7. We replace turn signal repeaters.
8. We install new ones.
9. We assemble the structure.

A complete list of lamps installed on Lada Vesta, their articles, prices are indicated in the article: https://remont-avtovaz.ru/kakie-lampy-ispolzuyutsya-na-lada-vesta/.

Other (spare parts, maintenance) Lada Vesta

Products from the Dustershop77 range on the topic of the article:

How to disassemble the side mirror on a LadaVesta. Step-by-step instruction

Required materials and tools:

• Phillips head screwdriver;
• plastic spatula;
• new diode strip or its analogues, substitutes, block assembly;
• additional lighting as needed.

Related link:

The five most common causes of suspension knocks

Algorithm of actions:

1. We turn off the engine and release the parking brake.
2. Open the driver's door.
3. We snap off the plastic casing with the built-in speaker.
4. We remove the blocks with wires.
5. Using a screwdriver, unscrew the three screws - self-tapping screws.
6. We remove the module - side mirror (hereinafter referred to as BZ).

1. We disassemble it into its component elements: insert, reflector, turn signal, cover.
2. Unsnap the left turn signal repeater and remove the turn signal repeater (hereinafter referred to as PP).

1. We install (replace) the turn signal in its original place, assemble the structure in the reverse order, if there are no other breakdowns or defects.

Conclusion

Changing a side mirror and installing a turn signal is easy. When purchasing LED products, carefully check the catalog numbers for compatibility with your car model.

If you find defects in cable and wire products or damage to the insulating layer, replace sections and update the contacts of the block with the wires. If necessary, seek advice from service station auto electricians and auto store managers.

Description of fuses on a Lada Vesta car: location, diagram, price

Lada Vesta cars are equipped with knife-type modules in the following modifications:

• Mini;
• JCase

The manufacturer abandoned the installation of cylindrical modules 7 years ago due to the obsolescence of the model.

Relay-breaker layout diagram

Lada Vesta fuse installation diagram

Causes of fuse failure

• Failure to comply with the scheduled technical inspection schedule;
• Installation of non-original spare parts;
• Unprofessional installation;
• Mechanical damage to adjacent mechanisms and units;
• Short circuit in the wiring;
• Damage to the insulating layer;
• Oxidation of contacts;
• Loose fixation of terminal blocks;
• Condensation formation, moisture penetration into the structure.

Reviews

Related link:

Lada Vesta car door handle repair

Work progress

Dismantling

First of all, you need to remove and disassemble the side rear view mirror itself.

First, remove the plastic trim from the front pillar inside the car. It is held in place by 3 clamps. The top one must be snapped off, and then the remaining two fasteners at the bottom must be disengaged.

Afterwards, the wiring plugs are disconnected and the mirror itself, which is secured with 3 screws, is unscrewed. They can be unscrewed with either a 10 mm socket or a TorxT20 bit.

Next, the process of disassembling the mirror begins. First, the mirror component must be rotated to the side.

This creates an opening through which the mirror component can be snapped off and removed from the mirror housing. Everything is done with a flat-head screwdriver, but you need to work carefully.

The cover itself is made of plastic. It is held in place by latches, and therefore can be removed simply by prying it with a screwdriver or knife, without dismantling the mirror component.

Everything is clearly shown in the video.

How to turn on heated mirrors

Starting in 2016, AvtoVAZ equipped the 2180 with the additional function of “electric drive and electric heating of side reflectors.”

This function is activated only after starting the engine (so as not to damage the battery) and switching on the heater to the window blowing mode (windshield and side). After this, you need to press the button on the climate console, which is responsible for heating and blowing the reflectors, rear and windshields.

To activate this function on the luxury version of Lada Vesta, you need to press the leftmost button at the bottom on the car’s climate control unit with the inscription “MAX”.

At 20-degree frost (which is usual for an Eastern European winter), the following happens:

1. after 1 minute the ice on the reflectors begins to melt;
2. after 2-3 minutes the ice melts completely;
3. after 4 minutes the mirror is clean and dry.