If the mileage of your Lada Granta car is approaching 15,000 km, then it’s time to plan to replace the cabin filter. As a rule, this procedure is performed at every maintenance service. However, it happens that for some, the filter is clogged already by 5,000 km, while for others, even after 30,000 km it still shows signs of life.
Everything depends not only on the operating conditions of the car, but also on the place where it is parked. Yes, this is not a mistake! The place where the car most often stops determines how often you will have to change the cabin filter.
This place could be a parking lot near your work or near your home. If there are a lot of trees and especially poplars around, then get ready for more frequent replacements. The fact is that poplar fluff, leaves and other small debris flying abundantly from trees can partially penetrate through the plastic grille of the JABO and end up on the filter.
If this phenomenon occurs frequently, then you will accumulate more debris in the engine compartment than usual. Now let's finish the lyrical digression and begin the replacement process.
2279-4-16-07 (Copy)
In this case, the arrow on the filter label should point down, and the word “front” should point toward the front of the car.
In this case, the arrow on the filter label should point down, and the word “front” should point toward the front of the car.
In this case, the arrow on the filter label should point down, and the word “front” should point toward the front of the car.
Replacing the cabin filter Lada Kalina, no more dust in the car interior
18.06.2018
The cabin filter serves to protect the driver and passengers from dust and other contaminants getting inside the vehicle, which, at best, can cause an allergic reaction, and at worst, lead to pneumonia and other respiratory diseases. The filter is protection against all street dirt: sand, dust, leaves, pollen and other contaminants.
How to replace the air filter on Lada Kalina.
Purpose of the cabin filter
As many believe, this type of filter material is needed in order to prevent dust and other larger particles from entering the car interior (leaving their marks on the panel, glass, seats, and upholstery). Yes, they're right. Nevertheless, the positive properties of this automotive component do not end there.
Thus, the main task of the filter is to prevent foreign particles from entering the heater engine (whose cost is approximately 2 thousand rubles, and to replace it you will have to remove the entire dashboard, for which the technicians will ask a considerable amount). Note that it is cheaper to prevent a problem than to solve it later.
The duration of replacing the cabin filter for an experienced technician will be no more than 15 minutes, for an amateur (30-40 minutes on his own).
When to change
It is recommended to replace this type of filter material every 15 thousand kilometers. Nevertheless, this figure cannot be called residual.
It all depends on where (exclusively in the city or more often on the highway) and how (with or without air conditioning) you operate your vehicle.
If in most cases you move around a dusty city, then you need to replace it after no more than 10 thousand kilometers.
Signs of a Replacement Needed
- It became harder to breathe inside the car;
- The stove and air conditioner are too loud;
- Windows quickly fog up;
- In the summer, the air conditioner does not cool properly, and in the winter the stove practically does not heat;
- The appearance of an unpleasant odor (due to the accumulation of dirt and bacteria).
Replacement feature
Replacing the cabin filter of a Lada Kalina is a fairly simple operation for a professional, which cannot be said for an amateur. Before you change the filter, you need to know where it is, how to remove it, and what tools you need to use.
Discounts on new cars! Advantageous loan from 9.9% Installment plan 0%
Tools
To get to the filter, you will need only three tools: an asterisk wrench and two screwdrivers (slotted and Phillips).
How to find it
Under the hood - with it open, look for the filter on the passenger side between the engine compartment and the windshield. It is protected by a grille made of plastic.
How to remove
When removing the cabin filter, you need to proceed according to the following “scheme”:
- first of all, remove the plastic grille by unscrewing 5 screws (2 of which are protected by plugs that can be easily removed by using a flat screwdriver);
- remove the wipers or leave them raised;
- unscrew the screws securing the casing;
- take it out;
- dismantle the filter by pushing away the plastic retainer with your fingers.
How to install
- There should be an arrow on the new filter - look for it;
- Then install the filter element with the arrow pointing towards the hood;
- Close all latches;
- Assemble the structure in the opposite order to disassembly.
We hope this article was useful to you.
We have tried to cover each question as much as possible, thereby providing you with valuable information. And as they say, “he who knows what is at stake is the one who rules.” Now you know how to remove the cabin filter on Kalina yourself and perform the replacement procedure without professional help.
Good luck!
2279-4-16-10 (Copy)
When installing the right windshield trim, the two tabs of the trim must extend beyond the front fender flange.
When installing the right windshield trim, the two tabs of the trim must extend beyond the front fender flange.
When installing the right windshield trim, the two tabs of the trim must extend beyond the front fender flange.
[14 Lada Granta maintenance operations that will help you save]
[How to save money on scheduled maintenance of Lada Granta] [Maintenance of Lada Granta at 2.5 thousand km] [Maintenance of Lada Granta at 15,000 and 105,000 km] [Maintenance of Lada Granta at 30,000 and 60,000 km ] [Maintenance of Lada Granta at 45 thousand km] [Maintenance of Lada Granta at 75 thousand km] [Maintenance of Lada Granta at 90 thousand km] [Carrying out maintenance yourself - general recommendations] [Safety rules for doing it yourself carrying out maintenance] [Tools required for maintenance of Lada Granta] [Lamps used in the Lada Granta car]
Lada Granta: changing the cabin filter and cleaning the drainage hole of the plenum box
How to replace the cabin filter on a Lada Kalina photo, video, articles
One of the simplest repair operations on the Lada Kalina is considered to be replacing the cabin filter. As a rule, the manufacturer skimps on such things and initially the owners themselves have to install it. As written in the maintenance and repair manuals, the cabin filter should be replaced every 15 thousand kilometers, and ideally 2 times a year.
Detailed video on replacing the cabin filter on a Lada Kalina:
Filter replacement process
Cabin filter produced by AvtoVAZ
So, in order to replace the cabin filter, you will need some tools and knowledge of the location of the product in the car. Tools you need:
- Accordingly, the new filter itself.
- A T-20 screwdriver, which is found in almost every tool kit.
- Phillips and flathead screwdrivers.
- A rag.
When you are finished with the tools, you can proceed directly to the replacement process. Let's take a step-by-step look at how you can change the cabin filter:
- Open the hood.
Open car hood - Under the plastic protective grille there is a cabin filter.
It needs to be dismantled. You can remove it by unscrewing the screws, of which there are 5 pieces. Unscrew the 5 screws that are hidden under the plugs - But before you get to the screw itself, you need to remove the plug.
This can be done by prying it with a screwdriver or other sharp object. Use a screwdriver to pry off the plugs to get to the screws - Carefully, so as not to break anywhere, remove the grille.
After the screws are unscrewed, move the grille - We dismantle the stove casing.
To do this, you need to unscrew the two screws that secure it. Remove the stove casing by first unscrewing the fastening screws - Now you can see the old filter itself.
Unclip the fasteners and carefully remove it. We dismantle the old filter - Install a new filter.
We install a new filter instead of the old one - We carry out assembly in the reverse order from disassembly.
Now, a new cabin filter is installed, and you can forget about it for the next 15 thousand km.
Selecting a filter for Lada Kalina (original and analogues)
11180-8122010 is the original catalog number of the cabin filter for the Lada Kalina. It is produced at the AvtoVAZ plant under the model range 1117-1119. There are analogues of this part, which are produced by the companies Livny, Citron and Neva, under identical article numbers.
Carbon cabin filter produced by Livny
Nuances when you need to change the filter
Because it changes after the winter period, when dirt mixed with water has accumulated in it and it is forgotten and does not allow air to pass through well. Before winter, because in summer there is a lot of dust and dirt on the roads and the filter involuntarily gets clogged.
This is what a very used cabin filter looks like, you breathe it in!
The cabin filter is changed because dust and foreign objects that enter the car interior are automatically inhaled by a person, and this can have a detrimental effect on health. This air can cause quite a lot of diseases, including cancer and pneumonia, so you shouldn’t skimp on your health and the health of your passengers.
conclusions
Replacing the cabin filter on the Lada Kalina is quite easy and simple. Every car enthusiast can easily carry out this operation, which does not require special knowledge and skills.
Replacing the cabin filter Lada Kalina step by step instructions. Leading auto portal
The interior of the second generation Lada Kalina has become more modern: the original seats with a heating system are easily adjustable and can be folded out comfortably. Positive changes also affected the instrument panel. One thing is bad - new plastic panels, upholstery and finishing varnish emit several dozen volatile toxic compounds, including carcinogenic substances (benzene, formaldehyde).
Harmful substances are also contained in exhaust gases that enter the cabin from the environment while driving or standing in traffic jams. They can cause various diseases, such as headaches, allergies, bronchitis, pneumonia, and even cancer.
The only protection against toxic substances is the cabin filter and the tightness of the car door seals. A conventional filter can only capture large dust particles. It is preferable to install carbon filters, but they also have disadvantages:
- The efficiency of air purification in the cabin due to the filter does not exceed 5%, according to experts.
- Short service life of carbon filters to neutralize harmful substances.
Signs of an urgent need to replace the cabin filter.
- 1. Fogging of car windows.
- 2. Poor air circulation in the cabin when the fan is on.
- 3. The appearance of unpleasant odors.
Step-by-step instructions for replacing the cabin filter Lada Kalina 2
1. Select and buy a new cabin filter.
It is advisable to purchase a filter in a plastic case and with an additional seal, which will ensure that debris does not enter the cabin heater.
The data in the table will provide assistance in choosing a carbon filter at an affordable price from different manufacturers.
Table 1.
| Cabin filter brand | ||
| Cost of 1 piece (in rubles) | 151 -183,97 | 669-810 |
Sometimes it is not possible to find a replacement standard cabin filter. In this case, you can use filters from the Chevrolet Niva (Filtron 1229 costing 340 rubles) or an analog cabin filter from other manufacturers Mann and NF (see table). You can find out how to install non-original filters and what problems may arise by watching the video.
2.Remove the supply ventilation grille (frill).
We fix the windshield wiper blades in a vertical position.
We take out two plugs from the right side of the frill.
Unscrew the five screws.
Carefully pull out the plastic grill (jabot).
3.Remove the waterproof filter housing.
To do this, unscrew the three screws, then move the casing to the right and pull it at an angle and towards you.
4.Pull out the old filter.
We press on the side latches that hold the filter in the box and carefully pull out the filter.
5.Insert a new cabin filter.
6.Reassemble the removed parts in reverse order.
7. Write down the date of filter replacement and speedometer mileage.
Replacing the cabin filter for Lada Kalina 1 and Lada Kalina 2 differs only in the removal of the protective casing. On second-generation cars, removing the waterproof cover requires unscrewing two screws, not three.
After replacing the filter, not only the air quality inside the car improves, but also the operation of the interior heater - in cold weather, the air in the car heats up faster.
Replacing the cabin filter on Kalina
The essence of replacing the cabin filter on Kalina is clear; all that remains is to figure out how to replace the filter correctly. The whole process is described to the smallest detail in this short photo session, to which we can only add that to dismantle the grille you will need a Torx bit, which every motorist most likely has.
Goals and tasks that we solved
We looked at how to replace a part called the cabin filter. In principle, you can not change anything, but simply clean it and return everything to its place. How best to accomplish this, the owner will decide for himself. Also, the instructions will be useful if the owner decides that it is necessary to change the stove radiator. First, the filter is removed, then the dashboard is removed, and then access to the radiator appears.
When dismantling the filter element, be careful. All kinds of debris or dust should not get into the compartment under the filter. It will no longer be possible to remove them from there, and the debris will end up on the fan of the heater unit.
The filter element, if not changed for a long time, can crumble from any touch. In such cases, there is no need to take unnecessary risks. For those who are not confident in their abilities, it is easier to entrust all actions to professional repairmen.
It is better to solve an existing problem rather than create additional ones. And in some cases, it is more advisable to contact a service station rather than try to fix everything yourself. We open the compartment, we see the destroyed filter - then we return everything to its place and go to the service center.
When to change the cabin filter on Kalina
The more often the better. The manufacturer recommends replacing the filter element every 15 thousand, but it is not the manufacturer who breathes, but we who breathe. Therefore, it is better not to bring the situation in the air ducts to such a state until it begins to show signs of poisoning:
- unpleasant smell in the cabin;
- heavy drawing of air through the filter by the stove engine in heating or ventilation mode;
- rapid fogging of interior windows;
- decrease in the performance of the ventilation and heating system.
To avoid the first signs of smelly germs, it is best to replace the filter ahead of time rather than hanging up a new fragrance. Based on experience, the cabin filter already requires replacement when exhaust gas odors penetrate into the cabin. This is the first sign. It’s better not to wait for the rest of the flock, but to spend these couple of hundred wisely and protect yourself and your passengers from allergies and other diseases. And being in a fresh car is much more pleasant.
How to select a filter element
In addition to the original VAZ “salonnik”, there are many analogues with different prices and properties. For example, there are carbon elements that have more effective air purification.
Most good quality filters are coated with a special solution that kills bacteria and prevents any diseases from entering the car. But the same filter may have different catalog numbers, such as the original:
- Coal - 11180-8122010-83.
- Regular - 11180-8122010-82.
If we talk about specific manufacturers, it is recommended to pay attention to the following companies:
- Original Lada. The price is 364 rubles - the best value for money.
- Filtron. Price 857 rubles.
- MANN. Price 872 rubles.
There are also cheaper analogues. But you need to choose a filter taking into account the operation. You can choose the road when using a car in a city where there is no dust and the likelihood of introducing bacteria into the car is higher.
In dusty areas, cheaper analogues should be used, since they will have to be changed much more often. The choice of manufacturer always falls on the shoulders of the car owner.
