Which cabin filter is better to choose for Lada vesta, xray

May 18, 2020 Lada.Online 45 063 4

According to the maintenance regulations, the cabin air filter on Lada Vesta and XRAY must be replaced once every 15,000 km. For proper operation of the interior ventilation and air conditioning system, the manufacturer recommends promptly changing the filter element. Let's figure out which cabin filter is best to buy.

Replacing the cabin filter on a Lada Vesta without removing the glove compartment (video)

If you have experience in servicing equipment, you can change the cabin filter on a Lada Vesta yourself.
If you don’t have the time or skills, contact a certified service center to order a service. The manufacturer of passenger vehicles in the operating instructions indicates an interval of 25 - 30 km. mileage In practice, the resource is not relevant for domestic transport; it is too increased. Motorists recommend “updating” the cleaning element at around 15,000 km. This is the best option, which is acceptable both for densely populated megacities and for peripheral areas.

Replacing the cabin filter for most motorists is, frankly speaking, a “trifling task”; however, on some models this task requires special skills and dexterity. For example, in order to change the interior of a Vesta, you have to disassemble the glove compartment...

However, thanks to the “handy folk” craftsmen, this work can be done much easier and faster. In this article, I will tell you, dear friends, how to replace the cabin filter on a Lada Vesta without removing the glove compartment.

The essence of the work, or rather the trick, is not to remove the glove compartment, but instead remove the plastic trim that covers the tunnel. Then, through the resulting window, we will replace the Vesta cabin filter.

Let's get started!

1. We find a plastic trim on the passenger side, such as in the photo. Then we take TORX T20 and unscrew the only screw securing this cover.

1. Now the cover is held in place by latches that need to be snapped off. To do this, you can use a plastic spatula or try to pry this pad at its bottom. We insert our fingers into the hole at the bottom and carefully snap off this decorative part.

1. Next, find the location of the cabin filter. Using two fingers, press the latches located on both sides of the cover under which the filter is located and remove it.

1. At this stage, nothing prevents you from taking out the old filter and replacing it. Be careful when taking out the filter, dirt, sand, leaves and much more may fall off it, so lay something down if you don’t want to stain the interior.

1. Installing a new filter is an unpleasant and very complicated procedure. The fact is that the filter is soft, and access to the mounting socket is not entirely convenient. Before installing a new cabin filter, make sure you install it correctly. The filter has arrows indicating the direction of the air. In general, if you are not sure, just try to fill it as the old filter was. Lightly compress the filter into an “accordion” and then carefully insert it into the mounting socket. In its place, the filter will straighten and take the correct position.

Next comes the assembly, it is done in reverse order; there is nothing complicated here, so I will not describe the process.

As you can see, there is nothing complicated! If you approach any work with intelligence and understanding, you can do anything. I have everything, write if it worked for you and what difficulties you encountered in the process of replacing the cabin filter on a Lada Vesta.

11 January 2022 LadaOnline 36,598

On Vesta and XRAY, the cabin filter (catalog number 272773016R) is located in the housing of the heating, air conditioning and ventilation unit. To gain access to it, you do not need to remove the frill (wind cover), as on other Lada cars.

Procedure

1. remove the glove compartment cover (you don’t have to remove it if you feel the tunnel lining clamps (from step 2) with your hand, putting your hand behind the shield on the engine side);
2. Remove the tunnel lining on the front passenger side by unscrewing the screw and unclipping the fasteners at the top.

Look under the panel. Remove the cabin filter cover (No. 2) by squeezing the clips (No. 3).

According to AvtoVAZ regulations, the cabin filter on Lada Vesta must be replaced every 30,000 km or once every 12 months. However, mechanics advise carrying out the operation at least once every 15,000 km, and if the car is operated in unfavorable conditions (lots of dust, etc.), it is recommended to reduce the interval by half or even three times.

The peculiarity of the domestic sedan is that its filter is located directly in the housing of the heating unit, which means that the owner does not have to remove the frill from the windshield. All work is carried out directly from the inside of the car.

Where can I buy?

Usually coal is more expensive. The most popular sites are given in the table.

As you can see, the price can vary significantly. As a rule, this depends not only on the type of cabin filter for Lada Vesta, but also on the manufacturer. For example, foreign components produced by Mann and Pilenga brands (Italy) are significantly more expensive than domestic ones and even more expensive than original components.

When to change, what interior to install

According to the technical maintenance regulations, the cabin filter on Lada Vesta is replaced at least once a year. Or when passing every 2nd scheduled maintenance, that is, every 30 thousand kilometers.

However, when used on Russian roads, within the period specified in the regulations, the cabin filter becomes quite clogged and ceases to perform its functions. Therefore, to ensure normal filtration, owners recommend cutting the time frame for replacing the cabin filter by half.

The ideal option is to change the Lada Vesta cabin filter twice a year, once in the winter season, and once before the summer season. In the spring and summer, it is better to install coal, as it copes more effectively with various allergens and unpleasant odors. And in autumn and winter, ordinary dust is enough.

Although the service book indicates specific terms for replacing the filter element, it is often recommended to carry out the replacement earlier, that is, not according to regulations, but as needed. The basis for replacement are signs of filter contamination:

• When the car is used in the summer on dusty road sections, the filter element becomes much more clogged with fine dust, as a result of which replacement may be required earlier.
• With frequent idle time in traffic jams, the element becomes clogged with small particles of exhaust soot, as a result of which it may appear relatively clean in appearance, but at the same time the surface acquires a gray color, indicating severe contamination, and permeability is reduced to almost zero.
• In the fall, leaves can get into the air ducts - even a small amount can become a breeding ground for millions of bacteria that cause an unpleasant odor. It is quite difficult to get rid of it; you will need not only replacing the filter element, but also completely cleaning the box.
• Increased air humidity in the cabin (window fogging).
• Reduced ventilation and heating system power.
• Noise appears when ventilation is turned on to maximum.

Suitable sizes

When choosing a filter element, owners do not always use products recommended by the car manufacturer. Everyone has their own reasons for this, some say that the original is unreasonably expensive. Some people in the region sell only analogues, so there is a need to know the sizes by which you can subsequently make a selection:

• Height: 35 mm
• Width: 200 mm
• Length: 216 mm

As a rule, sometimes analogs for Lada Vesta can be a few millimeters larger or smaller than the original, there is nothing wrong with that. And if the difference is measured in centimeters, then of course it’s worth looking for another option.

Selecting an original cabin filter

The manufacturer recommends using exclusively original consumables, which, in general, is not surprising. They themselves are of good quality and are widely available in car dealerships, but their price may seem overpriced to many car owners.

Regardless of the configuration, on all Lada Vestas, the manufacturer recommends installing a cabin air filter with article number 272773016R (dust) or 272773151R (carbon). They are also known under other articles, there are no differences in them, and they are interchangeable:

• 272770567R
• 272777764R
• 272778214R
• 272779683R
• 272889739R

It is worth noting that sometimes consumables and other spare parts may be supplied to dealerships under different part numbers. Which can sometimes confuse those who want to purchase an original product.

When choosing between a dust and carbon product, car owners are advised to use a carbon filter element. This filter is more expensive, but it cleans the air much better.

It is easy to distinguish - the paper filter accordion is impregnated with a carbon composition, and therefore has a dark gray color. The filter cleans the air flow from dust, fine dirt, germs, bacteria and enhances the protection of your lungs.

Which analogues to choose

In addition to simple cabin filters, there are also carbon filters that filter the air more effectively, but they are more expensive. The advantage of coal SF is that it does not allow foreign odors coming from the road (street) to penetrate into the car interior.

But this filter element also has a drawback - air does not pass through it well. GodWill and Corteco carbon filters are of fairly high quality and are a good replacement for the original.

However, in some retail outlets the price of the original Lada Vesta cabin filter may be greatly inflated. In this case, it makes sense to purchase a non-original consumable item. In particular, cabin filters are considered quite popular:

Conventional dust cabin filters

• MANN-FILTER CU22011 – high-tech consumables from a well-known manufacturer
• BIG FILTER GB-9978 – popular brand, good fine cleaning
• Nevsky filter NF6433 – Russian manufacturer with an affordable price

Carbon cabin filters

• MANN-FILTER CUK22011 – high-quality and thick carbon coating
• BIG FILTER GB-9978/C – activated carbon
• Nevsky filter NF6433C – normal quality, affordable price

It makes sense to take a closer look at the products of other companies - they also specialize in the production of high-quality consumables for passenger cars:

• Corteco
• Filtron
• SCT
• Sakura
• GoodWill
• Fram
• JS Asakashi
• Champion
• Zekkert
• Masuma
• Nipparts
• Purflux
• Knecht Mahle

It is quite possible that sellers may recommend replacing the Vesta cabin filter with non-original cheap substitutes with a much smaller thickness. They are not worth buying, since their filtering characteristics are unlikely to be at the proper level.

Self-installation of a large air filter on Lada Vesta

Which cabin filter is better, carbon or regular?
our comparison Attempts by LADA Vesta owners to increase engine power and make its operation more flexible do not stop. Particularly valued are methods that do not require significant processing and costs, not to mention chip tuning, to which the attitude is ambiguous.

Finalization

And now, another way has appeared - a cold intake and a large air filter on the Lada Vesta, the same as the one on the Sport modification. The peculiarity of this method is that it is suitable for both engines of the model - 1.6 and 1.8 liters.

Lada Vesta Sport has an enlarged air filter created specifically for this version. In addition, this modification has a different air intake location - it is located next to the left headlight behind the radiator grille.

Components

The entire Lada Vesta Sport air filter kit consists of a number of elements. Their names and articles are presented in the table.

Alternative

However, one of the owners of Vesta, whose name is Evgeniy and is known on Drive under the nickname gps-nav, found an alternative way of installing a large air filter on the Lada Vesta, which is several times cheaper. It involves purchasing components from different cars and their subsequent modification.

Elements:

• filter element - Filtron AP 074/3 is suitable - 330 rubles;
• air filter housing from the Ford Mondeo 3 model – 600 rubles – can be purchased under article number 4609885902;
• air filter pipe from the VAZ 2111 model – 700 rubles;
• sewer pipe 75 mm and sewer bends 90° and 67° – 220 rubles;
• fitting - 30 rubles;
• plastic ties (2 units) and a metal clamp (2 units).

After all the listed components have been purchased, you can begin work.

Work progress

Self-installation of a large air filter on a Lada Vesta begins with modification of the housing itself. First of all, it is necessary to solder the factory hole through which air is taken in.

Next you need to solder the purchased pipe. You can do this in different ways - using epoxy resin, soldering a metal mesh, using a stapler, etc. But in general, soldering using a metal mesh provides the most durable fixation.

Next you need to connect the sewer pipes and outlets.

To prevent the connector from interfering with the installation of the filter housing, it must be recessed and secured with a tie.

Then you need to move the car’s battery to the right and back until it stops, since otherwise it will interfere with the installation of the large air filter housing on the Vesta.

The case itself needs to be tightly fixed, and to do this, place it in such a way that the rear legs rest on the corrugation with wires.

This completes the independent installation of a large air filter on the Lada Vesta.

Effect

If you consider the reviews of the owners who went through with this modification, it becomes clear that the effect is quite noticeable. They note that the engine begins to “breathe”, and not only at the bottom, but also works more vigorously after 3,000 rpm.

The engine revs noticeably easier up to 5,000 rpm. Those who often drive in traffic jams claim that the car has stopped shaking in traffic jams.

In general, installing a large air filter on your Lada Vesta yourself is completely worth it, especially if you don’t buy branded products.

Other options

Below are modification options from other West owners, using several other components. All details can be viewed in their logbooks.

Option from Ivan Kiselyov. On Drive under the nickname BAHO and his car Lada Vesta *Blues Sky*

Option from Alexander. On Drive under the nickname MiheyA and his car Lada Vesta sedan 1.8 AMT

On Drive under the nickname WaPJIaTaH and his car Lada Vesta Fantan

Design and principle of operation of the part

Which oil filter is best to choose for your favorite car top 10

Sample engines that are used in modern car models include a lot of mechanisms rubbing against each other. Operating in this extreme mode, the mechanisms require high-quality lubricant as motor oil. For the rational operation of the engine and its components, the use of high-quality oil filters and timely replenishment of the oil reservoir with the missing amount of liquid are required.

In order for the car to remain operational for a long time, it is necessary to monitor the condition of the spare part and the level of engine oil. Manufacturers of car parts for Vesta and other models offer a wide range of filters. They may look different, but the products do the same job, they have a single mechanism of action. The part cleans the lubricant, removes dirt and metal particles from engine parts and prevents them from getting back into the operating mechanism.

The filter component of the Lada Vesta car is visually similar to filters of other brands - it looks like a dark glass with a cleaning device in the middle. Despite its apparent simplicity, the part has a complex design.

Repair sequence

Lada xray and vesta: first kilometers on new AvtoVAZ models

To perform proper vehicle maintenance, you will need to follow a sequence of steps. It is noteworthy that replacing the cabin filter of the Lada Vesta SV Cross is carried out according to a similar scheme, without changes.

Prepare the necessary tools and consumables. Place the machine in a stable position and apply the handbrake. The filter element itself is located under the dashboard on the left side of the glove box. The filter is hidden inside plastic linings and covered with protective inserts that ensure tightness. To remove the filter, you will need to use a T20 Torx wrench and unscrew the fastening screws on the right side of the gearbox lining.

Next, you will need to use a flat screwdriver or a special spatula to pry off the three fastening clips

When dismantling, extreme care must be taken - the plastic latches are very fragile and careless movement can damage them. If the clips break, you will have to buy a new part or “collectively farm” new clips

For clarity, the fastening points are indicated in the figure with red arrows.

Similarly, pry up and dismantle the right side of the glove box lining. The screwdriver is driven into the slot and the latches are released using rocking movements.

Next, the glove compartment opens and Torx is taken. In the lower left corner there is the fixing screw itself. It will need to be unscrewed.

It is noteworthy that in different years of production and depending on the assembly, the fixing elements - bolts - can be of different configurations: for Torx, hex, screwdriver or socket wrench.

Consequently, the user may require a much wider range of tools. On numerous videos where the cabin filter of the Lada Vesta is replaced, the video does not talk about this moment.

1. Then you need to sequentially unscrew the remaining screws securing the glove box.
2. Next, carefully remove the small cargo box.
3. After the glove compartment is moved, you will need to disconnect the power terminal for the compartment illumination. After turning off the backlight, you need to disconnect the wiring harness to the dashboard. To do this, the white retainer is disassembled.
4. After this, you can completely remove the magazine rack from the machine. Next, it must be carefully placed on a previously prepared rag or special surface. Such actions are justified by the sensitivity of the casing to mechanical damage - the glove compartment is easily scratched.
5. Now you have free access to the filter itself. In many videos that show replacing the cabin filter of the Lada Vesta Cross, the video does not convey the details - many elements are not shown. The filter element cover is located right next to the bulkhead between the passenger compartment and the engine compartment.
6. To dismantle the element, unclip the plastic clips and remove it strictly to the right. It is not recommended to pull the cover in other directions - the lower part of the part moves along the guide rails.
7. The final step is to replace the filter itself. The white insert simply plugs into the socket and is just as easy to remove.
8. After the channels have fully opened, experts recommend cleaning the air channels from dirt, leaves and other debris. For cleaning, you can use a compressor or, if you don’t have one, a household vacuum cleaner. The nozzle is inserted into the air intake and debris is blown out of the system. After the procedure, you will need to clean the interior - all the dust will fly onto the panels, windows and dashboard.
9. Installing a new filter is done in reverse order. In this case, the insert itself should be removed from the factory package only immediately before installation. If liquid, dirt or foreign debris gets on the paper, this will significantly reduce its service life.

There are also some nuances during installation. There is an arrow on the top of the filter, it should be directed towards the rear of the machine.

The next nuance is installation. When installing, the part needs to be slightly crumpled, the seat is 10mm less in height. In this case, after installation the filter will straighten out and everything will be fine.

Replacement with glove box removal

This method takes a little more time, but allows you to better control your actions and the position of the element.

It is recommended for beginners who have no experience in performing such activities and cannot determine by force whether the filter is installed correctly.

Before replacing the element, the right floor covering and glove compartment must be removed.

The process consists of several operations.

1. The screw securing the tunnel lining to the floor is unscrewed (T-20 key). To make work easier, it is sometimes necessary to clean the splines from dirt.

2. The facing panel is removed. It is held in place by three latches; you need to find their location, press the latches and carefully pry the panel into the slot. You should work carefully, especially on old cars - plastic's intermolecular bonds weaken over time, it loses its plasticity and can easily break off. This is a problem, rattling will appear, you will have to come up with new methods of fastening. There are three latches on the panel; if desired, you can slightly reduce the height of the hooks to facilitate repeated dismantling, but this must be done wisely. It is better to use a heated metal object and constantly check the grip. This method allows, if necessary, to return the original geometry of the elements.

3. In the same way, carefully remove the side of the dashboard on the right side. Use a slotted screwdriver or a knife to locate the clamps and press the protruding teeth one by one.

4. The glove compartment is removed; to do this, unscrew the holding screws with a T-20 bat. It is necessary to remove the lower left and right screws and the three upper ones.
   1 of 4

   — +

   1.

   2.

   3.

   4.

5. The backlight is disconnected. The box is moved back a little and the connector is removed.

6. The filter cover is removed. It is secured with two plastic clips; the lower part of the element slides in grooves along the housing guides and is removed.

7. The air filter is removed. If it is tight, then to facilitate the process you need to perform oscillatory movements, and if necessary, compress it a little at the top. It is advisable to pay attention to the condition of the filter, taking into account the operating conditions of the vehicle. This will help you more accurately determine the time of the next element replacement.

8. The location of the filter is thoroughly cleaned of dust using a vacuum cleaner.

The installation process is done in reverse order. Before starting work, you need to check the dimensions of the element and pay attention to the position of the arrow. It indicates the direction of air movement and should face the cabin.

Replacing the cabin filter on Lada Vesta

Below we will consider when to change the cabin filter correctly, what is required for this, and what components are best to use.

Briefly about the purpose

The cabin filter is an element necessary to filter dust and dirt passing through the air flow from the outside. Such products are installed at the manufacturer’s factory, and are later replaced at a service station or by the car owner.

Common replacement options are a dust or carbon filter element. The latter provides a “deeper” cleaning from phenols and benzenes. The disadvantage of a carbon filter is its higher price.

Replacing the cabin filter of Lada Vesta 1.6 is simplified by the fact that the necessary element is located inside. This means “finishing” work, but with the dismantling of some parts.

Experts distinguish two options - with removing the glove compartment or without performing this work. The second method is preferable because it requires less time. For the purity of the “experiment” we will consider both ways.

Timing for replacing the cabin filter on Lada Vesta

Replacing the cabin filter on a Lada Vesta, provided that a high-quality part is installed, is needed after 15-20 thousand kilometers. Car developers set more flexible deadlines - 30 thousand kilometers.

But the manufacturer clarifies that its recommendation implies operating the vehicle in conditions of minimal air pollution.

In current realities, it is almost impossible to achieve this state, because in urban or rural conditions the level of dust is very high. That’s why it’s better not to delay the work and make a replacement after 10-15 thousand.

Signs of a malfunctioning cabin filter on Lada Vesta

In order not to waste time and money, it is important to identify the problem in time. Many car owners wait until the Lada Vesta service to replace the cabin filter. This approach allows you to increase the time of use of the part and money

But in some circumstances it is better not to take risks and do the work right away

This approach allows you to increase the time of use of the part and money. But in some circumstances it is better not to take risks and do the work right away.

Replacing the cabin filter on a Lada Vesta with and without air conditioning is necessary when a number of symptoms appear.

Let's highlight the main ones:

1. Deterioration in airflow quality when the corresponding function or heating system is activated. The malfunction is diagnosed by poor operation of the stove, which does not produce the required portion of warm air flow. In such a situation, the cause of the malfunction may not only be the filter element. Sometimes cleaning the air intake is enough to fix the problem.

2. The appearance of unpleasant “odors” in the cabin. The main sign indicating that the filter in the Lada Vesta is dirty is a stench when you turn on the blower or heating. This indicates that the filter device does not perform direct functions of air purification. To avoid illness or other consequences, a failed part must be replaced.

3. A layer of dust on the “tidy”. This is another sign that the cabin filter is not doing its job.

4. Fogging of windows. This symptom indicates a deterioration in the quality of the ventilation system, which is often caused by a dirty filter.

Consequences

If you ignore the problem, dust, small rubber elements, exhaust gases, harmful bacteria and other dangerous elements will enter the cabin, and then into the lungs of the driver and passengers.

In addition, contamination of the cabin filter is fraught with problems in vehicle operation:

1. The air flow deteriorates, which leads to a high load on the heating system. The motor operates at the peak of its capabilities, and this is fraught with overheating and failure. To change the stove, you will have to spend more time and money. It is not always possible to cope on your own, so you have to involve experts in the work.

2. Dust that accumulates on the air conditioner evaporator collects water. As a result, optimal conditions are created for the development of rust and the proliferation of dangerous microorganisms.

What to change for

Before starting work, you need to select and buy a cabin filter suitable for the Lada Vesta. The manufacturer supplies the simplest dust version (made of paper).

To install a similar part, it is important to know the catalog number (the original from the factory is Renault 272773016R). If desired, you can install another analogue or spend money on a higher quality carbon filter element

Replacement frequency

We must not forget that the cabin filter is a consumable with a limited service life.
The operating manual and the Vesta service regulations indicate an interval of 30 thousand kilometers. Allegedly, it is with this frequency that the interior fittings need to be changed. But the experience of car owners clearly proves that the figure is not even close to reality. Even the highest quality filter cannot withstand 30 thousand kilometers under normal operating conditions. If we add here the constant passage of road dust, smog, exhaust gases, pollen and other pollutants through the air ducts, the interval is reduced by at least 2 times.

Most Lada Vesta owners prefer to change the cabin air filter after a maximum of 15 thousand kilometers. When a car is often forced to drive on dusty roads, the resource of consumables is limited to 7-10 thousand kilometers.

The best thing for a car owner to do is to monitor the condition of the element and replace it if signs of wear appear. Moreover, it is better to do this at the first symptoms, and not wait for development and active manifestation.

The following signs indicate that a mandatory replacement of the Lada Vesta cabin filter is necessary:

• The temperature inside the cabin begins to change. Since the purifier has already completely exhausted its resource, the heating and air conditioning system loses capacity and cannot push air through the clogged filter. Therefore, in the summer when the air conditioner is turned on, it is still hot, and in the winter it is not warm enough.
• There is an excessive amount of dust in the cabin. Yes, it can enter through open windows and doors. But when you turn on the heater or air conditioner, all the air in the cabin penetrates through the air ducts, colliding with the filter. And since the main task of the filter is to protect against dust, when it penetrates inside the car, we can accurately talk about the depletion of the resource. Need a replacement.
• Dirt and dust actively accumulate on the glass from the inside. Another characteristic sign that the cleaner is not doing its job.
• Unpleasant smell. Reminds dampness or mustiness. Almost the most objective factor indicating the need to replace a consumable.
• Rapid fogging of windows. If the windows are all closed, the air conditioner, stove or just ventilation is running, but moisture accumulates on the glass in the form of fogging, it’s definitely time to say goodbye to the filter.
• Weak air flows through the deflectors. It does not matter whether the air is hot or cold when you turn on the air conditioner or stove. It always passes through the filter first and then exits into the cabin. When the fan spins at medium or maximum speed, but the air flow is weak, the filter is probably clogged. It does not allow air flow.

The cabin filter on Vesta is directly connected to the ventilation, air conditioning and heating systems of the cabin. Without changing consumables, you increase the likelihood of failure of components of these systems.

Dirty cabin filter that needs to be replaced

Replacing the cabin filter of Lada Vesta with your own hands

Signs of a malfunctioning cabin filter:

• in hot weather, the car interior gets too hot inside, and this is felt much more strongly than when the filter is working;
• foreign odors, previously unnoticed, become very pronounced;
• The dashboard and windshield of the car become dirty very quickly, and regular cleaning inside the car is no longer enough to keep the car clean;
• Regardless of the time of year, car windows regularly fog up.

The appearance of even one of the above symptoms indicates the need for urgent filter replacement. It is also recommended to install a new interior cleaner while preparing the car for the summer season. You should not ignore signs of malfunction of this spare part and delay the replacement, which must comply with the regulations, since such carelessness in the future can lead to serious health problems.

Installing a new filter

When installing a new cleaning element, you need to pay attention to the fact that the existing arrow on it corresponds to the direction of the air flow, namely to the rear of the car. Please note that you can insert a new cleaner only by bending it slightly diagonally. The reason for this is that the filter is taller than the niche intended for it

There is no need to fear damage to the part; when the filter is in place, it will straighten out as needed without losing its function

The reason for this is that the filter is taller than the niche intended for it. There is no need to fear damage to the part; when the filter is in place, it will straighten out as needed without losing its function

Please note that you can insert a new cleaner only by bending it slightly diagonally. The reason for this is that the filter is taller than the niche intended for it. There is no need to be afraid of damaging the part; when the filter is in place, it will straighten out as needed without losing its function.

All that remains is to install the filter cover, moving it until the latches engage along the lower guides.

Further assembly is done in reverse order.

Replacing the cabin filter of the Lada Vesta SV Cross is the same important procedure as replacing other consumables. Unfortunately, many people neglect this procedure, thinking that the cabin filter does not affect anything. Actually this is not true. The cabin filter plays a big role in the design of the car.

Firstly, the degree of air purification in the cabin depends on the quality and cleanliness of the cabin filter. And this is the air that we breathe. If it is poorly cleaned, then we will get sick with various viruses more often, and in general it is not very hygienic.

Secondly, the efficiency of heating and air conditioning systems depends on the cleanliness of the cabin filter. If the filter is clogged, then in the cold season the heater in the cabin will not work well, and in the hot season the air conditioner will not work fully efficiently.

Thirdly, if the cabin filter is clogged, then in rainy weather the windows in the cabin will fog up very much, which greatly impairs the view.

All these reasons point to one thing - it’s time to change the cabin filter. And it’s best not to put it off until later. Today we’ll talk about how to do it yourself.

Where is

Like most other cars, the cabin filter of the Lada X-Ray is located in the passenger compartment on the passenger side. The filter housing is located under the dashboard, so getting it out requires a little fiddling. At a car service center they will charge you about 700 rubles for a replacement, which is quite a lot for a 15-minute procedure.

The cabin filter makes the ride comfortable, so if a plug is installed, it is recommended to remove it and install a cleaning element. Much less dust will accumulate in the cabin. If you use carbon filtration, the air quality inside the car will become even noticeably better.

Signs that replacement is needed

The cabin filter itself does not in any way affect the driving performance of the car, and many car owners often forget that it also requires maintenance.

The manufacturer recommends changing the cabin filter at least every 15,000 km, and if the air is too dusty or polluted, then every 5,000 km. However, replacement may be required sooner. The need to change the carbon filter can be recognized by the following signs:

• Windows fog up more often, especially when it rains;
• there was a foreign unpleasant odor in the cabin;
• Dust settles faster on the dashboard elements;
• The stove works worse in winter, and heats up too much in summer.

Replacing the air filter on a Vesta manufactured by VAZ

To find the element we are interested in, we need to get close to the engine compartment (located next to the battery). To carry out various manipulations, it is necessary to temporarily remove the housing. So, under difficult operating conditions, installation of a new part is required every 15 thousand kilometers. Such factors include driving on rough terrain and in high gas pollution.

The manufacturer's basic recommendation is suitable if the vehicle is used in normal mode without overload.

Urgently replace the Vesta air filter if the following signs of a problem appear:

• lack of power when driving uphill;
• the engine is unstable at idle;
• increased fuel consumption;
• difficulty starting;
• acceleration dynamics are reduced;
• the accelerator pedal is “uninformative”.

You can buy a new air filter suitable for replacing a Lada-Vesta at any more or less large auto store. Ask a consultant to help you choose the right spare part if it is difficult to make an independent choice. For the same purpose, you can study in advance the forums of car owners of the same cars or consult with professionals. The original spare part is number 165460509R. But using this identifier it is possible to find both the original and an analogue. Another reference point is 16 54 605 09R Renault, which is produced at the same plant as the Lada Vesta and is completely identical.

Replacing the LADA Vesta air filter

The car is produced with petrol engines of 1.6 and 1.8 liters. Air filters in LADA Vesta are similar to those used on foreign-made cars. This was done in order to facilitate self-service. Any owner of a LADA Vesta should know how to replace the air filter. If he lacks knowledge and skills, then he can turn to specialized literature that describes in detail the operation of the engine. Despite the fact that the manufacturer prescribes changing the filter every 15 - 30 thousand km, it must be regularly inspected for contamination.

You can find the filter on the LADA Vesta to the right of the engine, in a black plastic box. To open the air filter cover, you need to pry the fasteners with a thin screwdriver and remove the cleaning element along with the cover.

Care must be taken not to break the fragile fasteners. If the filter is heavily soiled or has changed its shape, it must be replaced urgently.

You should not try to extend its service life by blowing it with a compressor or vacuum cleaner.

Air filter selection

Most car owners try to purchase original spare parts when replacing. But not everyone has the opportunity to get them for various reasons, for example, there are no official sales points nearby, or lack of funds to purchase an original part. Therefore, such drivers often turn to analogues, and there is nothing wrong with that. The main thing is to choose the right product correctly.

A clean filter element is the key to good car acceleration, fuel economy, and efficient engine operation. Some motorists themselves negatively affect engine performance by violating the regulations for checking the replacement of the air filter. Any driver can cope with its replacement without special knowledge and experience in carrying out similar work. On auto sites you can find many videos about replacing this element. But you should be as careful as possible, since any error during installation can lead to the supply of clogged air to the engine.

Which filter is installed and which one to choose?

Lada Vesta and X-ray are equipped with a Renault 272773016R cabin filter costing from 400 rubles. The original Renault packaging contains a Mann CU22011 filter costing from 500 rubles. If you do not want to overpay for a cabin filter, you can choose either the original Renault or other analog filters.

• AIKO AC0203C from 220 RUR
• AMD AMDFC738C from 200 rubles carbon
• BIG Filter GB9978 from 130 RUR
• Bosch 1 987 435 011 from 350 rub.
• Filtron K 1321 from 200 rub.
• Fortech FS146 from 150 rub.
• FranceCar FCR21F090 from 150 rubles coal
• Goodwill AG449CFC from 360 coal
• LYNXauto LAC1925 from 300 RUR

A good carbon filter purifies the air better than a regular paper filter, so when purchasing a filter element, pay attention to this point

Replacing the cabin filter on Lada Vesta

Replacing the filter The tools you need are two different screwdrivers, as well as a T-20 wrench. A video of filter replacement can be seen below.

1. Unscrew the screw that secures the decorative cover to the side. Using a regular screwdriver, we slowly engage and remove it, being careful not to damage the plastic latches. The plastic sidewall also needs to be removed.
2. The glove compartment has two self-tapping screws on the top and bottom. We unscrew them using T-20. After disconnecting the backlight wire, remove the glove compartment.
3. On the left side is the filter we need, hidden under the cover. It is held in place by conventional clamps. We replace the new Lada Vesta filter with a new one and put the glove compartment and decorative cover in their places. You must remember to blow out the niche where the device is located. Replacing the cabin filter on Vesta turns out to be a completely simple process.

Most Lada Vesta owners are skeptical about air purification devices. It is necessary to understand that this part, in good condition, retains dust from the roads and reduces the penetration of pathogenic bacteria inside. The Lada Vesta filter article number is Mann CU22011. You can buy a cabin filter from dealers and in the catalog of an online store, and replacing it takes just a few minutes.

Where is it located, when to change it and which cabin filter to install

On cars of the Lada Vesta family, the cleaning element is located in the center of the dashboard in the lower part. It is a mistaken belief that the filter is installed behind the glove compartment.

Place where the filter is located

To carry out preventive maintenance, temporary dismantling of the storage compartment will be required. However, experienced specialists practice replacing the cleaning element in a different way, which we will consider below.

When to change

Taking into account climatic conditions, the level of dust and gas contamination of the territory, the purifier needs to be updated every 15,000 km, with the exception of unscheduled maintenance situations.

• reducing the force of air flow from the deflectors;
• the appearance of a fetid odor and rot in the cabin, which is dangerous for the human respiratory system;
• Leaves, dust, and dirt fly out of the deflectors when the stove heater is activated;
• the onset of the time interval according to the instruction manual.

The algorithm for preventing the stove heater on Lada Vesta 1.8 is identical.

Preparatory stage:

• new cleaner;
• aerosol for cleaning the air conditioner evaporator (if necessary, its prevention);
• screwdriver with a Phillips bit, TORX key set to “20”;
• rags, plastic spatula;
• additional lighting provided that there is not enough daylight for work.

Sequencing:

1. We place the car within the perimeter of the repair area, provide priority safety measures, and squeeze the parking brake.
2. On the passenger right side, open the glove box and remove the contents.
3. We unscrew the three fixing screws and lower the glove box housing to the floor. First disconnect the lighting limit switches.
4. On the left side of the opening, we snap off the plastic cover, squeeze the cleaning element with an accordion, and remove it.
5. We blow out the cavity with a household vacuum cleaner or other device with a stream of compressed air.
6. Place the new filter in the direction of the arrow towards you.

Replacing the cabin filter of a Lada Vesta with air conditioning is carried out according to a similar principle.

The second and most rational way to replace the interior air purifier:

1. On the right side of the central channel, use a plastic spatula to pry off the cover. It is secured with three clips.
2. We unclip the cover of the filter housing and remove it, after squeezing it with an accordion.
3. We install a new cleaner.

Maintenance of the cabin air filter has been completed. We replace the carbon air element by analogy.

Location - Vesta cabin filter is located in the area of ​​the front passenger seat, on the left, behind the tunnel panel.

It would be a good idea to check and clean the filter at 15,000.

Suitable filters are original, with catalog number - 272773016R. Analogs: FRAM CF11706, BOSCH 1987435011, MAHLE LA923, MANN-FILTER CU22011.

Review of Manufacturer Prices

*prices are as of January 30, 2019.

Recommendations for selection

Service center specialists strongly advise purchasing consumables with original factory catalog numbers. However, the high price of the “original” is not affordable for every car enthusiast. Therefore, they are forced to look for cheap but high-quality analogues.

Always check the integrity of the packaging, the presence of protective holograms, and quality certificates. If anything is in doubt, it is better to refuse the purchase.

Conclusion

The process of replacing the cleaning element is simple, but requires care on the part of the repairman. Prevention will take no more than 10 minutes.

It is not necessary to contact a service station, but provided that there are no major breakdowns that require the prompt intervention of a specialist. Observe replacement intervals, buy original consumables.

What to prefer?

VAZ manufacturers equip vehicles with a filter component model such as Mann. The catalog number is recorded in the technical documentation.

It is not necessary to use the same model for replacement. After all, a huge number of products are put up for sale that are suitable for completing the Lada vesta interior. So, you can use elements from brands such as BIG, Ekofil, Nevsky. The cost of such products varies.

When selecting a filter, the article number is checked. Taking it into account eliminates the difficulties and problems associated with selection and installation.

In order for the replacement of the cabin filter to be successful, the features and recommendations of specialists, which are recorded in the technical documentation, are studied.

Replacing the cabin filter Lada Vesta

Before installing a new cleaning element, carry out comprehensive diagnostics to identify the breakdown or malfunction. There are often cases where, due to a lack of professionalism, the mechanic owner replaces a part that is not at all necessary. To avoid this, we carefully check the main components of the car and carry out troubleshooting.

Preparatory stage: consumables to be installed, a set of automotive tools, a flat-head screwdriver. Where is the cabin filter located: in the center of the dashboard, on the top right side.

Sequencing:

Car enthusiasts practice two replacement methods: with and without dismantling the glove box. Both methods are acceptable and both are used. The only difference between them is that in the second case, the “update” will take more time, since it is necessary to remove the auxiliary equipment.

• We place the Lada Vesta on a flat platform and open the front passenger door. There is no need to use an inspection hole; there is no need to use an electric lift. In our case this is of no use;
• in the lower part of the central channel on the right side, unscrew one fastening bolt securing the plastic decorative panel. We remove it from its regular place, having first unfastened the three plastic clips;
• A little higher on the top left is the cabin filter compartment. On the outside it is covered with a plastic cover. Unfasten it, remove the cleaning element, and place a new one. Putting the structure together.

Finally, we start the engine, activate the stove heater, and check the strength of the air flow coming from the deflectors.

This is not indicated in the instruction manual, but it is advisable to clean (blow out) the housing yourself with a stream of compressed air using a compressor or household vacuum cleaner before installing a new filter. Often, the remains of leaves and debris inside prevent the free circulation of oxygen in the system. As a result, 10 minutes of time and we restored the functionality of the mechanism with our own hands. Subject to following the algorithm of actions, the subsequent replacement of original parts is no earlier than after 15,000 km.

How often should I replace?

The manufacturer of passenger vehicles in the operating instructions indicates an interval of 25 - 30 km. mileage In practice, the resource is not relevant for domestic transport; it is too increased. Motorists recommend “updating” the cleaning element at around 15,000 km. This is the best option, which is acceptable both for densely populated megacities and for peripheral areas.

Not all owners share this point of view. Continue to install the new filter element strictly in accordance with the specified interval.

In what cases does the purifier need to be replaced:

• recommendation of the service station master;
• the onset of the time interval specified in the operating instructions;
• overhaul of the machine;
• the appearance of a fetid odor, dampness, and rottenness in the cabin;
• There is a weak air flow from the deflectors, despite the open position;
• no outside air comes in at all due to severe contamination of the cleaning fiber;
• mechanical (technical) damage to the filter due to an accident, impact, or collision. And also, violation of the dismantling / installation procedure due to lack of experience and skills.

What analogues of the original Lada Vesta filter are there?

The manufacturer of the original element for the Vesta was Renault. The filter device is made of a special nanofiber; it does not contain a carbon element. The cost of a spare part can reach 1000 rubles. You can save money by purchasing one of the high-quality analogues. One of the most popular filtration elements is the Pilenga FA-P0443 model from Pilenga. The quality material is not inferior to the original sample, but costs slightly less than the original. For car owners who prefer air purification using a carbon element, BIG FILTER and Finwhale companies offer their parts. Their main advantage is that coal retains not only dust, but also allergens, which is important for drivers with problems in the respiratory system. There are several Russian manufacturers focused on creating consumables for the Lada Vesta: Nevsky Filter, TSN Citron, SibTEK and others.

It is best to install a new element at the beginning of the summer season, for example, when replacing tires. This will prepare the car for a large amount of dust on the roads, get rid of flowering products, and improve the operation of the air conditioner. The replacement process should not be completely ignored. A low-quality part is harmful to health and affects the operation of the filtration system. Even a young car owner can handle the replacement process without turning to the help of specialists.

Preparing tools and supplies

Naturally, at the same time as changing the filter element, the oil is also changed, otherwise it would instantly become dirty. But for different modifications of Lada Vesta, different volumes will be required to fill the lubrication system:

• 1.6 l. (11189) - 3.6 l. oils;
• 1.6 l. (21189) - 4.4 l. for manual transmission, 3.2 l. for automatic transmission;
• 1.8 l. (21179) - 4.2 l.;
• 1.6 l. N4M - 4.3 l.

The work process itself must be performed with protective gloves, since we are talking about a chemically active compound. Before replacement, the car engine is warmed up - this allows you to better get rid of the remaining old oil and better clean the entire system as a whole. Accordingly, this will extend the life of the car engine.

The following is a complete list of the necessary tools and consumables that will be needed when performing the work:

• new filter element (either original or analogues from trusted manufacturers);
• container into which the waste liquid will be drained;
• hex wrench;
• set of keys with socket and cap included;
• a special puller key for unscrewing the filter element;
• stub;
• several dry rags;
• protective gloves or gloves.

Maintenance of Lada X-RAY > Remont-Avtovaz.ru

Like any car, the new crossover from AvtoVAZ called Lada X-Ray requires periodic maintenance. These measures are aimed at maintaining the car in working condition and eliminating minor faults.

Which AIR FILTER is better to choose for VAZ/LADA VESTA, X RAY. Replacing the Vesta,XRAY air filter

The automaker has drawn up a schedule for maintenance and repair of the Lada X-Ray, which includes all types of work to maintain the car in good condition. The first maintenance of the Lada X-Ray should take place after 15 thousand km, all subsequent ones – after the same mileage.

THAT. What and when to do

The list of maintenance work for the Lada X-Ray is quite extensive. But most of this work can be described as “tug, listen, check.”

That is, such routine maintenance can include such items as checking the level of technical fluids, diagnosing the suspension, checking play, tire pressure, lubrication of hinges and locks, etc.

But in the first maintenance there is also work related to the replacement of some working fluids and consumables. So, during this service the following are subject to replacement:

• Oil and filter element;
• Air filter element of the power plant;
• Cabin filter;

It is also necessary to check the level of other technical fluids (and replenish them if necessary) and the condition of the brake pads.

During TO-2, which is done after 30 thousand km, the service center performs the entire list of TO-1 work, and also replaces the spark plugs. According to the list of works, TO-3 fully corresponds to TO-1, but in addition the brake fluid is replaced.

All maintenance work is repeated up to TO-6. When hitting 90 thousand km. In addition, the accessory drive belt along with the tension roller, as well as the coolant, require replacement.

As for technical fluids, except oil, they should also be changed every 3 years if the car’s mileage has not reached the required level.

Let's summarize. Every one must be replaced:

• 15 thousand km - oil and filter, if necessary - pads;
• 30 thousand km - spark plugs;
• 45 thousand km – brake fluid;
• 90 thousand km – drive belts with tension rollers (timing and attachments);

These are the main types of work, and they must be performed. All other maintenance is mostly carried out during operation.

Nuances and features of maintenance

As you can see, the list of basic types of maintenance is not that significant, so servicing and repairing the Lada X-Ray with your own hands is a completely feasible task, especially since you can save money on it. The official service only charges from 5,000 to 10,000 rubles for services. (depending on the list of works), but you still need to buy replacement materials.

Of course, some of the other maintenance work on the Lada X-Ray cannot be done on your own. This concerns adjustments to the chassis, diagnostics of electronic components, etc. But in this case, it is not necessary to go to an official service center, because any normal service station can also perform the specified work and it will cost less.

Next, we will review what and where to look for when servicing the X-Ray yourself, because the car is relatively new and non-car enthusiasts know the design features of the power plant.

Functions that a high-quality cabin filter should perform

This list includes:

• remove the smallest solid particles;
• prevent allergenic plant pollen from entering the cabin;
• captures chemical compounds of exhaust gases (oxides of nitrogen, carbon, sulfur, compounds of heavy metals, etc.);
• minimizes the harmful effects of low-quality washer fluids (solvent vapors, alcohols).

But you shouldn’t think that cabin filters only improve the microclimate in the cabin; their use solves several other important problems.

1. Reduces the number of interior cleanings. While removing dust from plastic and leather interior elements is not difficult, cleaning fabric elements is a rather complex and time-consuming procedure.
2. Increases the reliability of all rotating pairs. This refers to electric motors that drive heating, air conditioning, and other units located in the cabin. Dust has abrasive properties and significantly increases the wear of rubbing parts.

The capabilities of filters depend on their design. The simplest and cheapest ones purify the air only from solid particles. The most effective ones for complex cleaning have, in addition to paper elements, activated carbon fillers.