Which cabin filter is better to choose for Lada Vesta, XRAY

Replacing the air filter on a Vesta manufactured by VAZ

To find the element we are interested in, we need to get close to the engine compartment (located next to the battery). To carry out various manipulations, it is necessary to temporarily remove the housing. So, under difficult operating conditions, installation of a new part is required every 15 thousand kilometers. Such factors include driving on rough terrain and in high gas pollution.

The manufacturer's basic recommendation is suitable if the vehicle is used in normal mode without overload.

Urgently replace the Vesta air filter if the following signs of a problem appear:

• lack of power when driving uphill;
• the engine is unstable at idle;
• increased fuel consumption;
• difficulty starting;
• acceleration dynamics are reduced;
• the accelerator pedal is “uninformative”.

You can buy a new air filter suitable for replacing a Lada-Vesta at any more or less large auto store. Ask a consultant to help you choose the right spare part if it is difficult to make an independent choice. For the same purpose, you can study in advance the forums of car owners of the same cars or consult with professionals. The original spare part is number 165460509R. But using this identifier it is possible to find both the original and an analogue. Another reference point is 16 54 605 09R Renault, which is produced at the same plant as the Lada Vesta and is completely identical.

Signs of a clogged filter

You can understand that it’s time to update the air filter in your Lada Vesta even without a thorough inspection.

If the driver feels that his car starts to jerk or pulls worse on uphill climbs, then you should take a look at the filter; it may be clogged.

Clogged air filter. Photo source: https://arhkino.ru/chto-takoe-vozdushnyy-fil-tr-dvigatelya-i-dlya-chego-on-nuzhen/

A direct indication of problems with engine “protection” is an increase in fuel consumption, as well as a drop in engine power.

An obvious sign of a clogged filter is the car braking while driving without pressing the brake pedal.

If at least one of the symptoms appears, you need to open the hood and check the cleanliness of the filter element.

Replacement frequency

We must not forget that the cabin filter is a consumable with a limited service life. The operating manual and the Vesta service regulations indicate an interval of 30 thousand kilometers. Allegedly, it is with this frequency that the interior fittings need to be changed.

But the experience of car owners clearly proves that the figure is not even close to reality. Even the highest quality filter cannot withstand 30 thousand kilometers under normal operating conditions. If we add here the constant passage of road dust, smog, exhaust gases, pollen and other pollutants through the air ducts, the interval is reduced by at least 2 times.

Most Lada Vesta owners prefer to change the cabin air filter after a maximum of 15 thousand kilometers. When a car is often forced to drive on dusty roads, the resource of consumables is limited to 7-10 thousand kilometers.

The best thing for a car owner to do is to monitor the condition of the element and replace it if signs of wear appear. Moreover, it is better to do this at the first symptoms, and not wait for development and active manifestation.

The following signs indicate that a mandatory replacement of the Lada Vesta cabin filter is necessary:

• The temperature inside the cabin begins to change. Since the purifier has already completely exhausted its resource, the heating and air conditioning system loses capacity and cannot push air through the clogged filter. Therefore, in the summer when the air conditioner is turned on, it is still hot, and in the winter it is not warm enough.
• There is an excessive amount of dust in the cabin. Yes, it can enter through open windows and doors. But when you turn on the heater or air conditioner, all the air in the cabin penetrates through the air ducts, colliding with the filter. And since the main task of the filter is to protect against dust, when it penetrates inside the car, we can accurately talk about the depletion of the resource. Need a replacement.
• Dirt and dust actively accumulate on the glass from the inside. Another characteristic sign that the cleaner is not doing its job.
• Unpleasant smell. Reminds dampness or mustiness. Almost the most objective factor indicating the need to replace a consumable.
• Rapid fogging of windows. If the windows are all closed, the air conditioner, stove or just ventilation is running, but moisture accumulates on the glass in the form of fogging, it’s definitely time to say goodbye to the filter.
• Weak air flows through the deflectors. It does not matter whether the air is hot or cold when you turn on the air conditioner or stove. It always passes through the filter first and then exits into the cabin. When the fan spins at medium or maximum speed, but the air flow is weak, the filter is probably clogged. It does not allow air flow.

The cabin filter on Vesta is directly connected to the ventilation, air conditioning and heating systems of the cabin. Without changing consumables, you increase the likelihood of failure of components of these systems.

Dirty cabin filter that needs to be replaced

Analogs

Judging by the reviews of car enthusiasts, it is not necessary to buy an expensive imported model; it is enough to supply goods from a domestic manufacturer. Analogues also cope well with the task.

The most common analogues:

• model from the company BM-MOTORSPORT - BM FA2180 with a cost of up to 200 rubles. This inexpensive copy is in no way inferior to the original Vesta filter;
• Pilenga FAP2180 is next in the price category (400 rubles). There is one significant drawback - the padding polyester layer is too thin, so the filter element does not fit tightly enough to the body;
• MANN-FILTER C27030 – when using this element, the price increases to 1000 rubles. Fits perfectly and is of high quality.

Air filter Lada Vesta, X-Ray, RENAULT Duster (1.6), air filter element OE

Lada Vesta cars have been produced since the beginning of 2015. This model is equipped with a VAZ-21129 engine, which is equipped with a rectangular filter, the housing of which is mounted on top of the engine. The factory code for the air filter is 165460509R.

The Lada Vesta engine air filter plays an extremely important role in supplying the car with a high-quality fuel-air mixture. It serves to purify the atmospheric air necessary for the engine to form a combustible mixture. Prevents dust, moisture, and foreign objects from entering the combustion chamber, which contribute to increased wear of parts of the cylinder-piston group.

Air filter 165460509R Italy, the most affordable in price, does an excellent job due to high-quality materials and advanced technologies. Thanks to the presence of pre-cleaners made of synthetic material and reliable fixation of the curtains, they provide maximum air purification.

To form a combustible mixture, the VAZ-21129 engine requires approximately fifteen times more air than fuel. That is, if you burned ten liters of gasoline in a day, the air filter had to process a volume of one hundred and fifty liters. The combustion of this mixture in the engine cylinders directly affects the power of the car engine.

As the filter is used, the working surfaces of the replaceable air filter element become dirty, it cannot pass a sufficient amount of air, which leads to:

• reduction in power and deterioration in the dynamic characteristics of the vehicle. A mixture that is too rich will not allow the engine to operate optimally;
• increased fuel consumption. The lack of air in the combustion chamber will be compensated by increasing the injection of gasoline, which will not burn completely, but will be released into the atmosphere along with the exhaust gases;
• Excessive fuel consumption will lead to an increased content of harmful substances in the vehicle exhaust. Prolonged operation in this mode contributes to the formation of carbon deposits on the pistons and spark plugs.

A car with a clogged air filter loses its power, and you start spending extra money on wasted fuel.

In accordance with the regulations, the replaceable element of the air filter of a Lada Largus car is replaced every 15 thousand km.

It should be taken into account that the air filter should be replaced not simply based on the mileage of the car after the previous maintenance, but depending on its condition and operating conditions.

If your Largus has to travel a lot on roads with dirt, crushed stone or gravel surfaces, which are characterized by increased dust formation, then filter maintenance should be carried out much more often. In the intervals between replacements, it is recommended to clean the element by carefully knocking out dust and blowing with compressed air.

[pp_youtube src=»https://www.youtube.com/embed/JGhuGexOw9c?feature=oembed» ]

When operating a LADA X-Ray, Vesta, ENAULT Duster in a dusty area, the mileage between element replacements should be reduced by 1.5–2 times. A deformed or damaged element must be replaced regardless of mileage.

The quality of our roads and their cleaning leave much to be desired; these intervals often have to be shortened.

It should be taken into account that operating a car in winter and in humid climates causes less damage to the filters. Accordingly, dry, dusty summers and sandy terrain will put it out of action much earlier.

Taking into account all these factors, it is necessary to replace the filter elements.

A damaged or heavily contaminated air filter element can cause severe wear and loss of engine power.

If the filter is not replaced, the engine begins to “choke” and take on oil, which negatively affects the condition of the cylinder-piston system. As a result, carbon deposits may appear on the pistons, and this is a direct path to major repairs.

It is necessary to regularly check the condition of the working surfaces of the air filter and, if necessary, replace the replacement element.

You can replace the filter on all LADA X-Ray, Vesta, ENAULT Duster cars yourself, even for an untrained driver, thanks to the simple design of the filter housing and accessible location. To perform the operation, just carefully open the latches on the case.

Before starting work, it is recommended to remove the wire from the negative terminal of the battery.

Other article numbers of the product and its analogues in catalogues: 165460509R.

Any breakdown is not the end of the world, but a completely solvable problem!

Which is the best cabin filter to choose on Vesta?

Replacing the cabin filter of the Lada Vesta is an important event on which driving comfort depends. Therefore, the choice of model must be taken responsibly

The best option is a factory filter, which is made specifically for this machine.

Article number and price of the factory filter

The catalog number of the original cabin filter is 272773016R. The price of the new model is 900 rubles. The device dealer is , which also provides models for the Renault car brand. The material is a special nanofiber.

Analogues: articles and prices

Many drivers do not want to spend money on original spare parts, so they prefer to buy cheaper analogues.

The most popular official analogue of the factory filter is MANN CU22011. You can buy it for your Lada Vesta for 600 rubles.

Another analogue used when replacing the cabin filter on Vesta is Pilenga FA-P0443. The average cost is 180 rubles. Despite the low price, it is famous for its good quality filter element. Therefore, many drivers choose this product.

An excellent carbon filter option is Finwhale with article number: AS433C. For this model you will have to pay 350 rubles.

Instructions for Lada Vesta

Procedure

:

1. remove the tunnel lining on the front passenger side by removing the screws;
2. Remove the glove compartment lid (if necessary).

Look under the panel. Remove the cabin filter cover (No. 2) by squeezing the clips (No. 3).

To remove the filter element from the stove body, pull it down by the bottom edge (the hole in the body is smaller than the size of the filter). Clean the seat from dust and debris (for example, dried leaves). Installing the cabin filter is carried out in the reverse order, observing the markings indicating the direction of the air.

The replacement process is also shown in the video:

Self-installation of a large air filter on Lada Vesta

Attempts by LADA Vesta owners to increase engine power and make its operation more flexible do not stop. Particularly valued are methods that do not require significant processing and costs, not to mention chip tuning, to which the attitude is ambiguous.

Finalization

And now, another way has appeared - a cold intake and a large air filter on the Lada Vesta, the same as the one on the Sport modification. The peculiarity of this method is that it is suitable for both engines of the model - 1.6 and 1.8 liters.

Lada Vesta Sport has an enlarged air filter created specifically for this version. In addition, this modification has a different air intake location - it is located next to the left headlight behind the radiator grille.

Components

The entire Lada Vesta Sport air filter kit consists of a number of elements. Their names and articles are presented in the table.

Alternative

However, one of the owners of Vesta, whose name is Evgeniy and is known on Drive under the nickname gps-nav, found an alternative way of installing a large air filter on the Lada Vesta, which is several times cheaper. It involves purchasing components from different cars and their subsequent modification.

Elements:

• filter element - Filtron AP 074/3 is suitable - 330 rubles;
• air filter housing from the Ford Mondeo 3 model – 600 rubles – can be purchased under article number 4609885902;
• air filter pipe from the VAZ 2111 model – 700 rubles;
• sewer pipe 75 mm and sewer bends 90° and 67° – 220 rubles;
• fitting - 30 rubles;
• plastic ties (2 units) and a metal clamp (2 units).

After all the listed components have been purchased, you can begin work.

Work progress

Self-installation of a large air filter on a Lada Vesta begins with modification of the housing itself. First of all, it is necessary to solder the factory hole through which air is taken in.

Next you need to solder the purchased pipe. You can do this in different ways - using epoxy resin, soldering a metal mesh, using a stapler, etc. But in general, soldering using a metal mesh provides the most durable fixation.

Next you need to connect the sewer pipes and outlets.

To prevent the connector from interfering with the installation of the filter housing, it must be recessed and secured with a tie.

Then you need to move the car’s battery to the right and back until it stops, since otherwise it will interfere with the installation of the large air filter housing on the Vesta.

The case itself needs to be tightly fixed, and to do this, place it in such a way that the rear legs rest on the corrugation with wires.

This completes the independent installation of a large air filter on the Lada Vesta.

Effect

If you consider the reviews of the owners who went through with this modification, it becomes clear that the effect is quite noticeable. They note that the engine begins to “breathe”, and not only at the bottom, but also works more vigorously after 3,000 rpm.

The engine revs noticeably easier up to 5,000 rpm. Those who often drive in traffic jams claim that the car has stopped shaking in traffic jams.

In general, installing a large air filter on your Lada Vesta yourself is completely worth it, especially if you don’t buy branded products.

Other options

Below are modification options from other West owners, using several other components. All details can be viewed in their logbooks.

Option from Ivan Kiselyov. On Drive under the nickname BAHO and his car Lada Vesta *Blues Sky*

Option from Alexander. On Drive under the nickname MiheyA and his car Lada Vesta sedan 1.8 AMT

On Drive under the nickname WaPJIaTaH and his car Lada Vesta Fantan

Other FILTRON selections for this brand

Replacing the Lada Vesta air filter

Its body is located immediately behind the battery. The cover is held in place by two latches, which should be pryed off with a screwdriver. It is better to warm up the engine to reduce the likelihood of clamps breaking - warm plastic is less fragile.

Now you can pull the cover towards you and remove the filter cassette. This must be done carefully so that dust does not fall into the inlet channel.

When you remove the air cleaner element, thoroughly clean the holder and the inner walls of the box. You can use a vacuum cleaner for this.

All that remains is to insert the new air filter and place the cassette in place so that the latches snap into place.

It is not recommended to try to clean out the old item and install it again.

Replacing the gasoline filter

The fine fuel filter is installed in a single module with the coarse filter. It fits in the gas tank. The main disadvantage of this design is the need to dismantle the fuel pump assembly. Knowing the catalog number of the fuel pump, you can order the required filter element. For Vesta it has the designation 21800113900900 or 8450008680.

To replace it, you need to remove the rear row sofa, open the service hatch and remove the fuel pump module assembly. Having disassembled the unit, the fine filter element is replaced.

Where is it located, when to change it and which cabin filter to install

On cars of the Lada Vesta family, the cleaning element is located in the center of the dashboard in the lower part. It is a mistaken belief that the filter is installed behind the glove compartment.

Place where the filter is located

To carry out preventive maintenance, temporary dismantling of the storage compartment will be required. However, experienced specialists practice replacing the cleaning element in a different way, which we will consider below.

When to change

Taking into account climatic conditions, the level of dust and gas contamination of the territory, the purifier needs to be updated every 15,000 km, with the exception of unscheduled maintenance situations.

• reducing the force of air flow from the deflectors;
• the appearance of a fetid odor and rot in the cabin, which is dangerous for the human respiratory system;
• Leaves, dust, and dirt fly out of the deflectors when the stove heater is activated;
• the onset of the time interval according to the instruction manual.

The algorithm for preventing the stove heater on Lada Vesta 1.8 is identical.

Preparatory stage:

• new cleaner;
• aerosol for cleaning the air conditioner evaporator (if necessary, its prevention);
• screwdriver with a Phillips bit, TORX key set to “20”;
• rags, plastic spatula;
• additional lighting provided that there is not enough daylight for work.

Sequencing:

1. We place the car within the perimeter of the repair area, provide priority safety measures, and squeeze the parking brake.
2. On the passenger right side, open the glove box and remove the contents.
3. We unscrew the three fixing screws and lower the glove box housing to the floor. First disconnect the lighting limit switches.
4. On the left side of the opening, we snap off the plastic cover, squeeze the cleaning element with an accordion, and remove it.
5. We blow out the cavity with a household vacuum cleaner or other device with a stream of compressed air.
6. Place the new filter in the direction of the arrow towards you.

Replacing the cabin filter of a Lada Vesta with air conditioning is carried out according to a similar principle.

The second and most rational way to replace the interior air purifier:

1. On the right side of the central channel, use a plastic spatula to pry off the cover. It is secured with three clips.
2. We unclip the cover of the filter housing and remove it, after squeezing it with an accordion.
3. We install a new cleaner.

Maintenance of the cabin air filter has been completed. We replace the carbon air element by analogy.

Location - Vesta cabin filter is located in the area of ​​the front passenger seat, on the left, behind the tunnel panel.

It would be a good idea to check and clean the filter at 15,000.

Suitable filters are original, with catalog number - 272773016R. Analogs: FRAM CF11706, BOSCH 1987435011, MAHLE LA923, MANN-FILTER CU22011.

Options instead of the original

Some car enthusiasts, after identifying the need to replace the filter element, seriously believe that there is no need to buy a new one. They remove it and clean it, some even wash it and blow it out. Externally, after such manipulations, the filter looks like it came straight from the store. But it is worth considering that the filter is a consumable material and its mechanical properties are not unlimited. This product has its own service life. A filtration element cleaned in this way may be damaged in further operation, and the throughput will increase sharply, which will negatively affect the operation of the motor.

In addition, long-term operation of a car with such a filter can lead to failure of the spark plugs and mass air flow sensor. The engine control unit will begin to incorrectly calculate the proportions of the fuel-air mixture, and fuel consumption will inevitably increase. All this can be easily avoided if you promptly replace the Lada Vesta air filter.

Considering that the cost of this component on Vesta is not that high, there is no point in washing or blowing the product. As a last resort, you can purchase not the original consumable, but an analogue. It costs much less, and in addition, analogues of air filters are presented in sufficient quantities on the car accessories market. You can use a standard air filter, which is recommended by the AvtoVAZ plant. At the same time, analogues are not inferior in their characteristics to the original.

Products allowed for installation on Lada Vesta

Of course, you always want to save money and extend the service life of components. But in any case, even the cheapest air filter will be better than one you clean yourself. A new product always lasts longer and is more reliable than a used one.

What air filter should I install?

Replacement intervals

every 20 thousand km.

For LADA (BA3) X-RAY (1.6 16V), FILTRON recommends the following air filters: AP 135/7. You can see the detailed characteristics of these filters in our catalog. The air filter completely cleans the air that enters the engine; this is a very important function in any car, including the LADA (BA3) X-RAY (1.6 16V)

The air that passes through the filter goes straight into the combustion chamber, so it is very important that it is clean. FILTRON AP 135/7 filters allow you to purify the air by more than 99%

Since the air that passes through the filter can be hot, and dust particles can be hot, air filters have fire-fighting properties, so we think that you have no questions left about which air filter to install in the LADA (BA3) X-RAY (1.6 16V).

Selecting an original cabin filter

The manufacturer recommends using exclusively original consumables, which, in general, is not surprising. They themselves are of good quality and are widely available in car dealerships, but their price may seem overpriced to many car owners.

Regardless of the configuration, on all Lada X-Rays, the manufacturer recommends installing a cabin air filter with article number 272773016R (dust) or 272773151R (carbon). They are also known under other articles, there are no differences in them, and they are interchangeable:

• 272770567R
• 272777764R
• 272778214R
• 272779683R
• 272889739R

It is worth noting that sometimes consumables and other spare parts may be supplied to dealerships under different part numbers. Which can sometimes confuse those who want to purchase an original product.

It is easy to distinguish - the paper filter accordion is impregnated with a carbon composition, and therefore has a dark gray color. The filter cleans the air flow from dust, fine dirt, germs, bacteria and enhances the protection of your lungs.

Top 5. GOODYEAR GY1102

Rating (2021): 4.30

The best balance of price and quality Finnish filter material, tight fit, bypass and check valves - everything for effective cleaning and timely oil supply. Quality at a reasonable price.

• Characteristics

  Average price: 286 rub.

• Country Russia
• Height, mm: 70
• Weight, g: 332

This model uses Finnish filter material Ahlstrom, which is widely used in many countries. The bypass valve ensures rapid supply of oil in the required quantity even in cold weather, when its viscosity increases significantly. The pressure in the filter quickly builds up due to the check valve. You can do the replacement yourself using special keys and pullers. Drivers consider this model a worthy analogue, not inferior in quality to the original ones. But even here there are fakes.

Advantages and disadvantages

• High-quality filtration
• Pressure builds up quickly
• Affordable price

• There are fakes

Air filter selection

Most car owners try to purchase original spare parts when replacing. But not everyone has the opportunity to get them for various reasons, for example, there are no official sales points nearby, or lack of funds to purchase an original part. Therefore, such drivers often turn to analogues, and there is nothing wrong with that. The main thing is to choose the right product correctly.

A clean filter element is the key to good car acceleration, fuel economy, and efficient engine operation. Some motorists themselves negatively affect engine performance by violating the regulations for checking the replacement of the air filter. Any driver can cope with its replacement without special knowledge and experience in carrying out similar work. On auto sites you can find many videos about replacing this element. But you should be as careful as possible, since any error during installation can lead to the supply of clogged air to the engine.

Suitable sizes

When choosing a filter element, owners do not always use products recommended by the car manufacturer. Everyone has their own reasons for this, some say that the original is unreasonably expensive. Some people in the region sell only analogues, so there is a need to know the sizes by which you can subsequently make a selection:

• Height: 35 mm
• Width: 200 mm
• Length: 216 mm

As a rule, sometimes analogues for Lada Xray can be a few millimeters larger or smaller than the original, there is nothing wrong with that. And if the difference is measured in centimeters, then of course it’s worth looking for another option.

Types of cabin filters

There are only 2 types of filters, so even a novice car enthusiast can understand their features.

Anti-dust air filter

Visually and technically it resembles a classic engine filter (you can compare it by opening a photo on the Internet). It is shaped like a geometric rectangle. It contains synthetic or cellulose fiber.

The advantage of this air filter on Vesta is that the price of such models is affordable (from 100 rubles). But if we talk about neutralizing unpleasant odors, then this species is noticeably inferior to its competitor.

Carbon filter

The filter element in this type of device is activated carbon. Synthetic fiber is also used.

The carbon filter includes 3 levels of protection:

• The initial level of cleaning allows you to prevent large-sized debris from entering the Lada's interior.
• The medium level of protection traps smaller particles because it is made of microfiber.
• The last level partially absorbs some types of harmful substances, as it contains activated carbon.

If you choose between two types, it is better to give preference to a carbon filter, since it differs in that it protects not only from leaves, insects and dirt, but also from harmful fumes and the smell of unpleasant gases. A regular air plane does not have this level of protection.

https://youtube.com/watch?v=07mBKC82vmI%3F

The spring and summer period is associated with the appearance of a large number of insects and active flowering of plants, so professionals advise installing a carbon filter at this time of year. In winter, you can save money and purchase an anti-dust filter device.

The price of this cabin filter can reach 3,000 rubles.

Where is

Like most other cars, the cabin filter of the Lada X-Ray is located in the passenger compartment on the passenger side. The filter housing is located under the dashboard, so getting it out requires a little fiddling. At a car service center they will charge you about 700 rubles for a replacement, which is quite a lot for a 15-minute procedure.

The cabin filter makes the ride comfortable, so if a plug is installed, it is recommended to remove it and install a cleaning element. Much less dust will accumulate in the cabin. If you use carbon filtration, the air quality inside the car will become even noticeably better.

Replacing the cabin filter on Lada Vesta

Below we will consider when to change the cabin filter correctly, what is required for this, and what components are best to use.

Briefly about the purpose

The cabin filter is an element necessary to filter dust and dirt passing through the air flow from the outside. Such products are installed at the manufacturer’s factory, and are later replaced at a service station or by the car owner.

Common replacement options are a dust or carbon filter element. The latter provides a “deeper” cleaning from phenols and benzenes. The disadvantage of a carbon filter is its higher price.

Replacing the cabin filter of Lada Vesta 1.6 is simplified by the fact that the necessary element is located inside. This means “finishing” work, but with the dismantling of some parts.

Experts distinguish two options - with removing the glove compartment or without performing this work. The second method is preferable because it requires less time. For the purity of the “experiment” we will consider both ways.

Timing for replacing the cabin filter on Lada Vesta

Replacing the cabin filter on a Lada Vesta, provided that a high-quality part is installed, is needed after 15-20 thousand kilometers. Car developers set more flexible deadlines - 30 thousand kilometers.

But the manufacturer clarifies that its recommendation implies operating the vehicle in conditions of minimal air pollution.

In current realities, it is almost impossible to achieve this state, because in urban or rural conditions the level of dust is very high. That’s why it’s better not to delay the work and make a replacement after 10-15 thousand.

Signs of a malfunctioning cabin filter on Lada Vesta

In order not to waste time and money, it is important to identify the problem in time. Many car owners wait until the Lada Vesta service to replace the cabin filter.

This approach allows you to increase the time of use of the part and money. But in some circumstances it is better not to take risks and do the work right away.

Replacing the cabin filter on a Lada Vesta with and without air conditioning is necessary when a number of symptoms appear.

Let's highlight the main ones:

1. Deterioration in airflow quality when the corresponding function or heating system is activated. The malfunction is diagnosed by poor operation of the stove, which does not produce the required portion of warm air flow. In such a situation, the cause of the malfunction may not only be the filter element. Sometimes cleaning the air intake is enough to fix the problem.

2. The appearance of unpleasant “odors” in the cabin. The main sign indicating that the filter in the Lada Vesta is dirty is a stench when you turn on the blower or heating. This indicates that the filter device does not perform direct functions of air purification. To avoid illness or other consequences, a failed part must be replaced.

3. A layer of dust on the “tidy”. This is another sign that the cabin filter is not doing its job.

4. Fogging of windows. This symptom indicates a deterioration in the quality of the ventilation system, which is often caused by a dirty filter.

Consequences

If you ignore the problem, dust, small rubber elements, exhaust gases, harmful bacteria and other dangerous elements will enter the cabin, and then into the lungs of the driver and passengers.

In addition, contamination of the cabin filter is fraught with problems in vehicle operation:

1. The air flow deteriorates, which leads to a high load on the heating system. The motor operates at the peak of its capabilities, and this is fraught with overheating and failure. To change the stove, you will have to spend more time and money. It is not always possible to cope on your own, so you have to involve experts in the work.

2. Dust that accumulates on the air conditioner evaporator collects water. As a result, optimal conditions are created for the development of rust and the proliferation of dangerous microorganisms.

What to change for

Before starting work, you need to select and buy a cabin filter suitable for the Lada Vesta. The manufacturer supplies the simplest dust version (made of paper).

To install a similar part, it is important to know the catalog number (the original from the factory is Renault 272773016R). If desired, you can install another analogue or spend money on a higher quality carbon filter element

Stages of replacing the filter element Lada X-Ray

Compared to most other cars, replacing the cabin filter in the Lada X-Ray is relatively simple. Relatively, because the filter is not located in the most convenient place for replacement. Simple - because no special preparation is required for this operation. All you need is the new filter element itself.

It is pointless to dispute the benefits of salon tea, especially when it comes to coal ones. Therefore, it is not surprising that self-installation of filters on cars has become common. This is a routine and fairly simple procedure for periodic maintenance, there is nothing complicated about it

According to the regulations, replacement of the cabin filter is provided every 15,000 km, that is, every scheduled maintenance. However, depending on the operating conditions of the vehicle, the replacement period can be reduced to 8-10 t.km. mileage The more often you change the filter in the cabin, the cleaner the air will be and the better the air conditioner or heater will work.

Where is

Like most other cars, the cabin filter of the Lada X-Ray is located in the passenger compartment on the passenger side. The filter housing is located under the dashboard, so getting it out requires a little fiddling. At a car service center they will charge you about 700 rubles for a replacement, which is quite a lot for a 15-minute procedure.

The cabin filter makes the ride comfortable, so if a plug is installed, it is recommended to remove it and install a cleaning element. Much less dust will accumulate in the cabin. If you use carbon filtration, the air quality inside the car will become even noticeably better.

Removing and installing a new filter element

First, you need to make a reservation that you can use the official instructions for replacement by removing the glove compartment. But this makes no sense other than wasting time. This method is less convenient, but very fast.

Replacing the cabin filter of the Lada X-Ray is a routine and fairly simple periodic maintenance procedure. There is nothing complicated about it, so replacing it yourself is quite simple. To make the operation easier, you can move the front passenger seat all the way back.

The filter plug can be seen behind the center console when viewed from the glove compartment, and to remove the filter it is enough to:

1. We get to the installation site (Fig. 1). Fig.1 Installation location
2. Access to the filter plug is open. To remove it, you need to squeeze the protrusions shown in the photo. The effort required for this is small, they give in easily. After this, simply pull the lid towards you (Fig. 2). Fig.2 Compressing the protrusions
3. Pull the filter by the lower part, moving upwards, so that the upper part of the filter disengages. The filter element itself is larger than the hole where it should be inserted. Therefore, it is pulled out according to the accordion principle (Fig. 3).

   
   Fig.3 Pull it out by the bottom part

4. When the installation cavity is empty, it is advisable to clean it of dust and various contaminants. If you can use a vacuum cleaner with a narrow attachment, this would be the best option. There is a more radical method, turn on the airflow to full. In this case, the inside will be clean, but you will have to remove dust from the interior (Fig. 4).

   
   Fig.4 Niche for installation

5. Next, install the new cabin filter in the reverse order. First, fully insert the upper part of the filter, and then push the lower part. It seems a little confusing, but the installation process makes it easy.

   
   Fig.5 New filter element

6. Now all that remains is to install the cover in its place until it clicks. By the way, for some users the latches on the plug break off. In this case, it can be secured with 2 self-tapping screws, for which there are already holes.

When installing, pay attention to the arrows shown on one side of the filter element. They show the direction of air movement, and installation must be done according to them. The arrow should be in the direction from the engine to the passenger compartment.

When removing the filter, as a rule, a large amount of debris spills onto the mat. It is worth vacuuming the inside of the stove body itself - the size of the slot for the filter makes it quite easy to operate with the narrow nozzle of the vacuum cleaner.

On cars with air conditioning, replacing the cabin filter should be combined with cleaning it. On sale you can find many aerosol compositions for cleaning and disinfecting honeycombs. A flexible nozzle is inserted through the filter installation hole.

The composition is evenly sprayed over the entire surface of the air conditioner radiator, after which it quietly flows through the drain. You need to wait about 10 minutes and replace the filter.

Solving the problem of large accumulation of debris in the filter

Very often, when replacing the interior, you can find tree leaves and other large debris. Which not only spills onto the floor of the Lada X-Ray cabin when replaced. But it also prevents normal air circulation.

The culprit is the air intake hole, which is located under the hood, behind the air intake box, or in common parlance, a frill. It is practically not covered by anything. All large particles enter through it. Covering it with a fine mesh will solve the problem.

Let's figure out how to do this:

1. For this purpose, special meshes with a fine mesh are available for sale. They are attached using strong neodymium magnets (Photo 1).

   
   Photo 1 Fine mesh mesh

2. Raise the hood and remove the plastic air intake box, which is located under the windshield. To do this, you will also need to remove the wiper arms.
3. To avoid confusion with the location of the wipers when replacing the wipers, it is recommended to make marks with a marker (Photo 2).

   
   Photo 2 Making marks

4. Now that all the fasteners have been disconnected, you can pull out the frill.
5. When everything is dismantled, we see in the center a view of an air intake with a huge cell, which needs to be closed (Photo 3). Photo 3 Original air intake
6. We insert our purchased mesh and close the standard hole with it. Now large debris will not get into the cabin, and as a result, the cabin filter will become less clogged (Photo 4).

   
   Photo 4 We rejoice at the modification

We are happy with the modification and put everything back together in reverse order.

Cabin filter functions

The increase in the number of cars on the roads and the availability of a car for almost every person has led to a sharp deterioration in the environmental situation. Cabin filters have become “shields” for the respiratory tract of drivers, as well as their passengers.

The Lada Vesta cabin filter is an air purifier that removes the smallest hard particles, such as sand or soot.

There are substances (NO2, nitrogen dioxide) that poison the human body and cause irreparable harm to the health of people with chronic respiratory diseases. The Lada Vesta cabin filter, filled with activated carbon, acts as an artificial barrier, preventing these substances from entering from the outside.

A high-quality filter serves as a protector of the car air conditioner evaporator from dust adhesion, and this is the key to good operation of the entire air conditioning system.

Antifreeze vapors can also irritate a person's lungs or cause severe headaches. The carbon filter prevents the “aroma” of this liquid from penetrating inside.

Review of Manufacturer Prices

*prices are as of January 30, 2019.

Recommendations for selection

Service center specialists strongly advise purchasing consumables with original factory catalog numbers. However, the high price of the “original” is not affordable for every car enthusiast. Therefore, they are forced to look for cheap but high-quality analogues.

Always check the integrity of the packaging, the presence of protective holograms, and quality certificates. If anything is in doubt, it is better to refuse the purchase.

Which analogues to choose

In addition to simple cabin filters, there are also carbon filters that filter the air more effectively, but they are more expensive. The advantage of coal SF is that it does not allow foreign odors coming from the road (street) to penetrate into the car interior.

New Lada: Which cabin filter to install on the Lada Xray? — New Lada

But this filter element also has a drawback - air does not pass through it well. GodWill and Corteco carbon filters are of fairly high quality and are a good replacement for the original.

However, in some retail outlets the price of the original Lada X-Ray cabin filter may be greatly inflated. In this case, it makes sense to purchase a non-original consumable item. In particular, cabin filters are considered quite popular:

Conventional dust cabin filters

• MANN-FILTER CU22020 – technologically advanced consumables from a well-known manufacturer
• BIG FILTER GB-9978 – popular brand, good fine cleaning
• Nevsky filter NF6433 – Russian manufacturer with an affordable price

Carbon cabin filters

• MANN-FILTER CUK22020 – high-quality and thick carbon coating
• BIG FILTER GB-9978/C – activated carbon
• Nevsky filter NF6433C – normal quality, affordable price

It makes sense to take a closer look at the products of other companies - they also specialize in the production of high-quality consumables for passenger cars:

• Corteco
• Filtron
• SCT
• Sakura
• GoodWill
• Fram
• JS Asakashi
• Champion
• Zekkert
• Masuma
• Nipparts
• Purflux
• Knecht Mahle

It is quite possible that sellers may recommend replacing the Xray cabin filter with non-original cheap substitutes with a much smaller thickness. They are not worth buying, since their filtering characteristics are unlikely to be at the proper level.