Wheels for Lada Vesta Cross: choice, size, bolt pattern

Lada Vesta Today, there are various wheels for Lada Vesta on the market. The main differences between them are the materials from which they are made, methods of manufacture and fastening, and sizes. To choose the right components for your car, you should know their standard sizes, presented in the table below.

T – permissible speed index within 190 km/h;

N – permissible speed index within 210 km/h;

88 – load capacity index from 88 to 560 kg, 91 – from 91 to 615 kg;

ET – rim offset, indicating the distance from the mating surface of the disk to the middle of its rim;

partial load – the presence of three adults in the cabin, without cargo in the trunk;

full load - the presence of more than three adults in the cabin, or the presence of three adults in the cabin and luggage weighing 50 kg or more (depending on the capacity of the luggage compartment).

The wheel is secured to the car hub using four bolts through the holes on the disk. It has four holes centered on a diameter of 100 mm.

Removing and installing the hub: front and rear

This part is always hidden behind the wheel, so first, lift the rear or front of the car and remove the wheel. To do this, unscrew the bolts with little effort, moving from one to another in order, so that dismantling occurs as quickly as possible. Before doing this, the car needs to be stopped in place; it is better to do this using wheel chocks.

To replace the hub on the front wheel of a Lada Vesta:

1. Lower the brake fluid level in the reservoir.
2. Press down the brake cylinder piston carefully so as not to damage the protective casing. Separate the pads.
3. Using a 18 mm socket, unscrew the bolts securing the disc to the steering knuckle, hang the disc brake on the suspension spring. Do not remove it far, place it away from the sharp ends of parts so that the brake hose is not damaged.
4. Unscrew the casing mounting bolts and remove the casing.
5. Closer to the center of the car, the wheel speed sensor wire is connected to the top - disconnect it. Before doing this, unscrew the bolt next to it. Take out the wiring harness.
6. Unscrew the ball pin fastening nut and disconnect the steering rod from the steering knuckle.
7. Unscrew the remaining steering knuckle nuts and remove the bolts. First, remove the front wheel drive shaft, and then remove the steering knuckle assembly.
8. Replace the part, reassemble everything in reverse order.

To work with the rear wheel of a Lada Vesta, the process looks like this:

1. Unscrew the hub fastening nut, and then remove the drum along with the bearing, retaining ring, and magnetic ring from the axle.
2. To remove the bearing, press the magnetic ring with a three-arm puller.
3. Place the drum on the press table, place the mandrel 78.7853-9728-1 on the bearing.
4. Press the bearing out of the drum.

To install the bearing, thoroughly clean all parts from dust and dirt for excellent adhesion, and carry out the work in the reverse order.

Basic characteristics of wheels on Lada Vesta

Lada Vesta is a domestically produced sedan, which has been produced by the VAZ plant since 2015. A special feature is the Lada Vesta wheel size with parameters R16-R17, in contrast to earlier models, which are characterized by the use of standard sizes R13-R14.

Initially, this model was released on the market with wheels size 185/65/r15. Gradually, the manufacturer decided to switch to wheels on the Lada Vesta of an increased size, reaching 16 - 17 inches. The decision to install wheels of a different size made it possible to significantly increase Vesta’s handling and stability on the road.

General background information

Ranges of possible values ​​for tires and wheels Lada Vesta 2019.
Tires

Wheel disks

Photo

Expert advice

When choosing tires for a car, you must first follow the manufacturer's instructions. Ask yourself a few questions.

• On what roads will the car be primarily used?
• Do you need increased cross-country ability?
• How much of the route will be city roads and how much will be highways?
• Will the vehicle carry heavy loads?

The answers to these and similar questions will help determine which tire parameters you need to pay special attention to.

How to choose the right wheels for Lada Vesta 2022?

3 types of rims:

• Stamped (economical price category) - made from a sheet of iron by stamping on a press.
• Light alloy - manufactured by casting (more reliable than stamped ones).
• Forged (the highest quality and more expensive than the previous ones) - made from light alloys by stamping at high temperatures.

The choice depends on financial capabilities. However, it should be borne in mind that the quality of the road surface on which you have to drive every day must also be taken into account.

So, if it gets into a hole, a stamped disk will bend and will not cause harm to the tire, but a forged or cast one can cut it. There is a possibility that the cast disc may burst or crack.

It should also be noted that repairing “stamping” wheels is cheaper than repairing cast or forged wheels. But wheels with high-quality cast and forged disks kill the suspension less, because lighter and have more perfect geometry (better balanced).

The same wheels may or may not rub with tires on the same car - wheel alignment adjustment will help here.

What is the tire pressure?

It is the driver's responsibility to constantly monitor tire pressure. This will avoid standard problems associated with vehicle operation. An abnormal pressure value often causes:

• deterioration of management;
• uneven tread wear.

Often the car owner independently reduces the pressure in the wheels of his own vehicle. This reduces the load on the suspension, and the car “passes” various road irregularities an order of magnitude easier. But it is worth noting: a decrease in pressure even by 0.1 MPa leads to serious problems. The main ones include:

• increased fuel consumption;
• rapid wear of the outer tread segments;
• the car becomes less maneuverable.

An overinflated wheel causes no less problems. The central part of the cylinder begins to wear off quickly. In addition, at ambient temperatures of more than 60 degrees Celsius, the tire may simply explode. Which will lead to driving into the oncoming lane.

Alternative wheel sizes for Lada Vesta SV Cross: characteristics

Many owners strive to enlarge the wheel rollers in order to give the appearance a more aggressive appearance and visually enlarge the car. Low-profile tires are almost always installed on such wheels, and they are highly sensitive to uneven roads. Therefore, the comfort of movement is lost, but for many, appearance is more important.

An alternative solution for the Lada Vesta SV cross is r17 wheels, visually they are several times larger than the standard size of fifteen-inch wheels. The cost is no more than five thousand rubles for one skating rink, but if we talk about foreign goods and exclusive design, the price can quadruple. If the Lada Vesta Cross has 235\45 tires, then you can even install eighteenth-sized wheels. They are able to visually make the car truly sporty and dynamic. The cost of products starts from nine thousand per disc.

Purpose and features

First of all, the rim allows the car to move on the road because it holds the rubber tire. In addition, they can serve as an additional decoration for the appearance. The tire does not fly off thanks to the ring protrusion. It cannot be too heavy and must meet the geometric requirements that are imposed during production.

Wheels affect handling and overall dynamics.

If you choose different wheel sizes for the Lada Vesta, you can change the operating parameters of the car. Firstly, a larger diameter has a positive effect on the quality of vehicle control and trajectory retention. On the other hand, there is a feeling of discomfort when moving over uneven surfaces. Secondly, a wider one will make driving more comfortable, but will increase fuel consumption. Thirdly, control also depends on the choice of tire size: the wider, the better. However, the wider the tire, the higher the fuel consumption, and also the resistance to aquaplaning decreases and the noise level increases.

Decoding Lada Vesta tire sizes

The tire sizes given in the tables are encrypted in the form of numbers and letters, which do not mean anything to the uninitiated person. In order to understand what parameters a tire has, you need to be able to read their markings correctly.

For example, let's take the standard size for Lada Vesta Cross 205/50 R17 89V. You can decrypt it this way:

• The first number indicates the width of the tire in millimeters. In our case it is 205 mm.
• The second number, which is written separated by a slash, indicates the ratio of the tire width to its height as a percentage. If this value is 50, then the tire width will be 102.5 mm.
• The letter R does not denote the radius, as most drivers believe, but the radial type of tire. Most modern products use this type of internal structure.
• After the letter R, the manufacturer indicates the rim diameter (also known as the inner diameter of the tire, measured in inches). In our example it is 17 inches.
• The next number indicates the maximum load on the wheel. The index, which in our case is 89, means that the maximum load should not exceed 580 kg. Data on this can be seen in the table below:

After the load index comes the speed indicator. You can also determine it using the table.

In addition to this basic information, additional information is also indicated on the tires. For the average motorist, an important indicator will be the company and country of manufacture, as well as the seasonality of the tires. Tires intended for winter have a snowflake pictogram and the designation W or M+S (M&S, Mud + Snow). Summer tires are sometimes designated with a “sun” pattern, but do not have a letter designation.

Vesta SV wheels from the factory

The standard dimensions of the slopes of the basic West SV assemblies coming off the AvtoVAZ assembly line have parameters such as 185/65/R1588Н . Some batches of these vehicles may be equipped with T-series tires. In this case:

• 185 – means the width of the slope in mm;
• 65 is the percentage of the tire profile compared to its width. If in millimeters, then it will be 65/100*185=120.25;
• R15 is not the radius, but the diameter of the rim intended for this tire in inches;
• 88 – this digital index indicates the tire’s permissible load capacity of 560 kg;
• H – means permissible speed up to 210 km/h. While T is 190 km/h.

Alloy wheels

Popular alloy wheels on the Lada Vesta are distinguished by a wide selection of designs and diameters. They are made from a special alloy. In addition to the base metal aluminum, the alloy contains magnesium, strontium and titanium additives. The casting process occurs under high pressure, which promotes rapid hardening of the workpiece. Using computer modeling and milling, the part receives its final shape.

Alloy wheels

The multi-level manufacturing process of alloy wheels explains their high cost. They are lighter in weight, but have less resistance to mechanical damage.

Lada Vesta casting is presented by the manufacturer in two versions:

• r15 rollers are recommended for tires with dimensions 175/70 R15 and 205/60 R15;
• R16 wheels are suitable for tires with dimensions 185/60 R

Alloy wheels 15 radius on the Lada Vesta are provided when purchasing a car in the “luxury” configuration. For an additional fee, alloy wheels 16 radius can be installed as additional equipment on the Lada Vesta.

You can buy alloy wheels for Lada Vesta in specialized centers and online stores, the websites of which contain photographs of the products. The average price for casting with a radius R15 is 2500 - 4000 rubles, depending on the manufacturer and design. 16-inch rollers will cost the car owner more - from 3,500 to 6,000 rubles apiece.

Alternative wheel sizes

In pursuit of beauty and unusual appearance, Lada Vesta owners install skating rinks of seventeenth and eighteenth radii. They include low-profile tires, which are very sensitive to the slightest irregularities in the road, which makes driving a car less comfortable.

Wheels r17

Quite often there are Vesta cars with wheels with a radius of R17. They look noticeably larger than the standard fifteen inches. Recommended tire sizes for this type of casting are 175/55 R17, 195/50 R17. External features are presented in the photo of Lada Vesta on 17 disks. You can buy such shoes for cars for 5,000 rubles apiece; foreign-made goods with an exclusive design will cost 15-17 thousand.

Wheels r18

For the first time, rollers of this size were presented on the Lada Vesta concept with 235/45 tires. A photo of the Lada Vesta on 18 rims clearly demonstrates the sporty design and dynamics of the car. R18 castings are much more expensive than their “younger brothers” - from 9,000 rubles apiece.

Interesting color solutions

Recently, it has become very popular to combine contrasting colors in car design. This fashion trend contributed to the release of skating rinks in different colors. On the Internet you can find many photographs with various combinations of car body colors and disk rims.

It is recommended to install rims on a white Lada Vesta in a contrasting black color. The black casting looks good against the background of the white body. Using the same principle, you can choose wheels for a black Lada Vesta

White skating rinks will stand out brightly and attract the attention of others. Classic silver casting fits cars of any color and is a universal option

Among the numerous design innovations, Vesta wheels with a bright red edging along the edge of the rim and on the spokes attract attention. They fit any car body color, but it is preferable to install them on a red car

This combination gives the car a sporty look and unique personality. Even in dense city traffic, the car will stand out from the crowd and attract the attention of others.

Installing larger diameter discs

Large rims not only change the appearance of the car, but also affect its dynamics, maneuverability, and stability on the highway, and not always for the better.

When deciding on their installation, you should know the basic principle - the larger the diameter of the disk, the lower the height of the tire profile, because the size of the outer diameter of the wheel is tied to the size of the wheel arch - when turning, the tire should not touch or rest against anything at all steering wheel rotation range.

Testing the Lada Vesta over the course of a year showed acceptable wheel size options:

17-inch wheels were installed on the Concept version of the Lada Vesta. Technically, this sedan can also be equipped with R18 wheels, but the outer diameter of this wheel (669 mm), as well as the tire width (235 mm), differ significantly from the factory values ​​and cannot be considered in the real conditions of Russian roads due to the too low profile as practical - defects in the road surface will quickly damage both tires and wheels, the price of which, due to their size, is several times higher than the cost of standard ones.

The effect of large-diameter wheels and low-profile tires on a car

• increasing the style of the car and the effectiveness of the exterior;
• improvement of driving qualities - dynamics, road stability, steering sensitivity;
• better “absorption” of potholes compared to a smaller radius;
• with a tire profile from 55 – increased durability of the suspension;
• reducing the braking distance;
• increasing the efficiency of ABS and ESP.

• uncomfortable driving due to sensitivity to road surface defects;
• restriction of use on roads with defective surfaces;
• the need for increased pressure control;
• greater need for kinetic energy at the start - higher fuel consumption;
• higher cost.

Low profile tire pressure

This parameter, ignored by novice car enthusiasts, is very important when operating cars with any tires, and especially with low-profile ones. The required tire pressure is always indicated by the vehicle manufacturer in the operating instructions and in an accessible place on the body, for the Lada Vesta - on the B pillar on the driver's side.

Low profile tires require increased attention to pressure, as insufficient pressure will make the wheels and suspension even more vulnerable to potholes and rocks on the road.

As many years of experience have shown, the pressure in low-profile tires must be maintained 15% higher than that specified by the manufacturer for wheels of the recommended size.

Selection of disks for Vesta

The quality of Russian roads leaves much to be desired, so sooner or later the rollers will have to be replaced, since they wear out much faster on such roads. Another reason for replacement is the desire to change stamped to casting or choose a different design.

In such cases, there is no point in recommending standard wheels with a radius of 15; it would be better to choose R16 or R17. For 16's you can use tire sizes 175/70 and 205/60. For 17's the optimal tires are 175/50 and 195/50.

The following discs are recommended by the manufacturer:

But that doesn't mean others aren't suitable. There is a huge arsenal of discs of various types and at different prices. When choosing them for Vesta, you should take into account that the bolt pattern (the distance between the wheel bolts) differs from that used on other VAZ cars. As before, there are 4 bolts for fastening, but if previously the diameter between them was 98 mm, then on Vesta the bolt pattern is 4/100.

At the same time, aesthetically the car will look original. But with such rollers you will have to use low profile tires. And this, given the condition of the roads, will make everyday trips unpleasant.

Rating of alloy wheels for Vesta

For convenience, this shortlist is compiled from bottom to top, i.e. the best brand will be at the end. The top casting includes the following brands.

1. LS Wheels. Manufacturer from Taiwan. The products are certified by Rosstandart and adapted to Russian operating conditions. Pros: a wide variety of castings, attractive design and low cost. Of the minuses: not the best quality.
2. Alcasta. This brand is preferred by connoisseurs of classics and strict design. The company's products have been sold in Russia since 2013. They are distinguished by excellent balancing from the factory, light weight and low price. The disadvantages include the softness of the metal and poor paint coverage.
3. LegeArtis. Stylish and high-quality alloy wheels, despite the fact that they are made in China. Production is carefully controlled at every stage, products undergo multi-level testing. Modern technologies are used, but the quality of the metal leaves much to be desired; at high speeds and when falling into holes, cracks and other mechanical damage may appear.
4. Replica. A brand that produces copies of original wheels from the world's leading automakers. The quality of the discs depends on the factory, and there are several of them. Over the course of many years of history, the company has gained an impeccable reputation. In addition to high quality and a large selection, car enthusiasts will be pleased with low prices. However, on some copies, namely those included in the kit, there are different weights and incorrect geometry.
5. Dotz. One of the world's best disc manufacturers from Germany. The company is narrow-profile and deals exclusively with car wheels, so the product is of a high level. All products comply with international standards and are tested at every stage of production. In addition to quality and beautiful design, the brand offers a range of prices and a wide variety. Oddly enough, there are virtually no shortcomings.
6. K&K. The products are characterized as high quality, inexpensive and reliable. This is a Russian product, and it is the wheels of this manufacturer that AvtoVAZ uses. Parts are manufactured using modern equipment and meet international standards. There are no minuses as such; the pluses include an interesting design.

What wheels can be installed on Vesta

What wheels does the automaker propose to install on the Lada Vesta? AvtoVAZ does not recommend changing the tire size or offset, suggesting that only wheels with increased or reduced width be used.

Wheels with a diameter of 15 inches can be installed in widths from 5 to 6.5 inches (remember, the base has 6 inches). And wheels with a diameter of 16 inches can be from 5.5 to 6.5 inches wide (the base is 6.5 inches). The same applies to 17-inch wheels on the Vesta Cross or wheels on the sports Vesta - if you wish, you can install narrower wheels, 5.5 and 6 inches wide, without violating the requirements and warranty policy of the automaker.

As for tires, AvtoVAZ allows the use of tires with other speed and load capacity indices. Standard 185/65R15 88H tires can be replaced with tires with load capacity index T. And 16-inch tires 195/55R16 91H can be with speed index 87 and/or load index T. Wheels on the Lada Vesta Cross size 205/50R17 89V can be replaced tires with a lower load index H.

What non-standard wheels will fit on the Lada Vesta

Although most car owners tend to enlarge their wheels to improve the appearance of the car, sometimes the opposite happens. For example, it is common practice to drive on larger diameter alloy wheels in the summer, and then take smaller wheels and a larger tire in the winter to make the car more controllable and softer on snowy roads. The best option for such a replacement is to install 185/65R15 wheels from the basic configuration. It is not recommended to install wheels smaller than 15th diameter, and we have not seen examples of such a replacement.

Vesta on 19-inch wheels

As for the maximum diameter, the critical height of the wheel assembly for Vesta is 660 millimeters. Therefore, not only the original 17-inch wheels are installed on the car, but also wheels with tires with a diameter of 18 inches. In this case, the tires should be no larger than 225/45 R18, and for some car owners they already cling a little to the wheel arch liners. True, on drive2 there is a case with installing 19-inch wheels, but this will require improvements in the suspension design. And in the case of installing 18-inch wheels, some tire sizes also allow you to lower the car, which many do. In any case, when choosing wheels and tires, you will need a calculator. Just sit down and calculate whether your purchase will fit into the wheel arches or not. Or look at our table below.

Is it possible to reduce the offset and install wider wheels? Do not forget that the manufacturer already recommends installing 17-diameter tires on 6.5-inch wide wheels with an offset of 43. That is, there are not many options here. The maximum permissible width of wheels on a Vesta is 8 inches with an offset of 38. In this arrangement, the wheels practically do not stick out and do not touch the arches. Anything more requires modification of the machine design. By the way, don’t forget that a smaller offset reduces the life of your wheel bearings. So you will have to either change it more often, or buy more expensive parts.

We also remind you that any replacement of wheels with non-standard sizes has advantages and disadvantages. By installing larger tires and wheels you will definitely improve the appearance of your car, its dynamics and stability. But you will have to pay for this with less comfort on bad roads and a possible increase in fuel consumption

In the case of low profile tires, which will most likely have to be placed on large rims, you will also have to get used to constantly monitoring the tire pressure, because the tires are more sensitive to this important parameter, as well as to shaking on uneven roads

Alternative wheel options for Lada Vesta are in the table.

Review of the best summer and winter tires

For a comfortable ride, you should have two separate sets of tires - for driving in the summer and winter. If you have a limited budget, the Sava Adapto HP MS tire will be the optimal solution for summer. Its cost will be no more than 3,800 rubles per cylinder. At the same time, it is durable and can be used even in winter.

If you have enough money, you should purchase Michelin Crossclime+ tires. Its price is slightly higher - from 4,500 rubles. The wide contact patch makes it easy to keep the car on the road in any weather conditions. The tread has many channels to drain water from the contact patch.

Goodyear Vector4Seasons tires will cost slightly less than Michelin. However, they will make the movement of the car no less comfortable. However, unlike the model discussed above, the rubber composition does not contain silicon. Which makes the protector less durable and wears out quickly.

Hankook RA33 has a bi-directional tread, so if necessary, the wheels can be easily switched sides. This model will be relatively cheap. The price will be approximately 3,500 rubles. The maximum permissible speed is 190 km/h. There are as many as 4 longitudinal grooves - they help avoid hydroplaning of the car.

Pirelli Cinturato P1 tires are the optimal solution for driving a car in the summer. The wheel can easily withstand a load of 610 kg. Therefore, this model is perfect for cars used to transport families.

Pirelli Winter Formula ICE studded tires provide a high level of comfort and safety - regardless of operating conditions. Even when driving on ice, the car stays confidently on the road.

Hankook W429 tires with steel studs allow you to move at high speed in the cold season. Thanks to the unique composition of rubber, it does not harden at low temperatures.

Nokian HKPL-9 – business class studded tires. Thanks to the unique fastening of metal dumbbells, they remain in place throughout the entire period of operation.

Gislaved Nord Frost is distinguished by its low cost (no more than 4 thousand rubles for 1 wheel) and durability. Maximum speed – 190 km/h. Using such tires, the driver will not have to worry about his safety on the road in winter.

Continental Ice Contact will cost 4,500 rubles or more. This model was introduced back in 2015. However, it is still considered relevant.

You can install any tires or wheels that fit your size on your Lada Vesta car. Installation of R14 is also allowed. However, you must first make sure that there are no compatibility gaps.

Tires and their parameters

High-quality summer and winter tires are important for any car. Even if you have a Russian Lada Vesta car, its wheels should be reliable and strong, and its tires should have good treads. Often car enthusiasts are not interested in what tires were installed on the car from the factory. They put the cheapest option. The position is incorrect, because the driving safety, driving properties of the car, and its stability depend on the parameters of the wheels and their quality.

The manufacturer of the Lada Vesta specifies specific characteristics for wheels, and people rely on them to select the right model. It should be noted that Vesta, which has been produced since 2015, uses wheels with R16-R17, previously the plant practiced installing smaller sizes. The wheels had dimensions 185/65/r15. Now the size of the disks has increased, Vesta’s stability in motion has increased. After reading the article you will understand which wheels should be on the Lada Vesta.

When purchasing 15, 16 or 17 inch wheels for your car, don’t expect them to last forever - they won’t. In time, the question of replacement will arise. Russian roads force even expensive wheels to break quickly. Some drivers are not satisfied with the parameters of the wheels or tires, so they change them.

If the time for replacement has come, many parameters must be taken into account. These are wheel size, rim type, rim offset (ET), wheel bolt pattern, diameter and other parameters. Products with the following technical data are suitable:

• casting with wheel size 175/70/R16 or 205/60/R16;
• alloy wheels 175/55/R17 and 195/50/R;
• for the Lada Vesta SV Cross station wagon, 18-inch wheels are needed;
• tires are used exclusively on 16 and 17 inches.

AvtoVAZ uses a number of wheels produced by K{amp}amp;K. If you take them, drilling, bolt patterns and other parameters will converge. A good option would be to install r16 and 17 Phoenix wheels.

The plant recommends choosing narrow winter tires for the Lada Vesta. This is necessary to increase stability when driving on slippery roads in sub-zero conditions.

Before purchasing wheels, pay attention to the bolt pattern. On the Lada Vesta it has changed somewhat; not all wheels will be compatible with it. The rims are secured with 4 bolts, the diameter of the mounting holes is 100 mm. The wheels of Korean cars have similar characteristics.

We do not recommend installing wheels with a significantly larger diameter. This will make driving less comfortable. It will be less resistant to driving on uneven roads.

At the factory, alloy wheels are installed on luxury trim levels. If you have seen a Lada Vesta in the photo with 15 alloy wheels, it means that the driver of the car installed them himself, or it is a luxury one. Typically, the manufacturer installs products from the Russian company K{amp}amp;K. It is a leading manufacturer of die-cast wheels.

Lada Vesta is equipped with high-quality factory wheels. They have practical performance characteristics and most buyers do not change them for many years. But some people see the Lada Vesta in the photo on 17-inch alloy wheels and want to install these for themselves. Be aware that then you will have to install low-profile tires, the ride will become less comfortable. But the solution has advantages, discussed earlier.

Before choosing tires, the driver must understand that the size of car tires very seriously affects various characteristics of the car. Perhaps the grip will improve, the car will stay on the road perfectly at speeds of up to 210 km per hour, others increase the load capacity and speed index. Of course, the manufacturer indicates factory values ​​that are considered optimal for a particular model.

• factory recommended tire size is 185/65 R15 and 195/55 R16;
• if the wheels are 15 inches, the tire size is 175/70 R15 and 205/60 R15;
• for 17-inch wheels choose tires 175/55 R17 and 195/50 R17.

The manufacturer puts optimal tires on its Lada Vesta cars. These are Belarusian Belshina tires. They are designed specifically for AvtoVAZ and have high reliability and good quality. If you are puzzled by the choice of winter or summer tires, you can install the products of the Belarusian plant. Tires for Lada Vesta belong to the ART Motion brand, which is of Spanish origin. This means that the quality of the wheels has been tested according to the standards of the country of origin - Spain.

No matter how good the wheels on the Lada Vesta are, sooner or later they have to be changed. The harsh conditions of our roads negatively affect the life of any wheels. Also, some car owners want to replace the standard wheels of a new car with alternative ones with a different design.

In such cases, the following types of wheels and tires for tire fitting can be recommended for Vesta:

• exclusively 16 or 17-inch tires;
• alloy wheels 175/70/R16 or 205/60/R16;
• alloy wheels 175/55/R17 or 195/50/R

The latest model is different in size, which changes the stability of the car for the better.

If winter tires are required for the Lada Vesta, then it is better to choose narrower ones, as they have higher stability at low temperatures and slippery roads typical of winter conditions.

When buying rims for Lada Vesta, you should pay attention that the Lada Vesta bolt pattern is somewhat different from that previously used. Wheel compatibility depends on which bolt pattern is used. These wheels are designed to be mounted with four bolts, and their sizes correspond to the sizes of bolts for Korean cars, which significantly expands the range of wheels for this car. The diameter of the mounting holes is 100 mm.

If there is a need to install wheels made of light alloys, then we can recommend the products of the company PDW, which specializes in the production of forged and cast wheels for domestic brands of cars. Therefore, the parameters of PDW disks correspond to the maximum possible extent to the standards adopted by VAZ.

It should be remembered that installing wheels of an inappropriately large diameter significantly reduces ride comfort, especially when driving on potholes and other uneven surfaces. Increasing the width increases almost all qualities of the wheel, except stability on wet roads.

Alternative to standard disks for Vesta

Mainly just to give the car a more attractive appearance, many motorists install larger wheel rims on the Lada, namely R17 and R18. This means using tires with a low profile, which is associated with discomfort when driving over uneven surfaces. However, some car enthusiasts prefer to sacrifice convenience for the sake of beauty.

17th radius

R17 are considered the most popular alternative rollers for Vesta. They stand out against the background of the standard 15s. For these, tires with sizes 175/55 and 195/50 are suitable. Of course, the larger the radius, the higher the price. Therefore, on average, you will have to pay about 3,000 and 5,000 rubles for stamped and cast ones, respectively. Products of top-rated foreign manufacturers, namely castings with a beautiful and unusual design, can be valued at 15,000 or more.

R18

They were first shown in the concept version. Later, rollers of such a large size appeared on the Lada Vesta Sport and in the Exclusive configuration. The cost of disks is much more expensive than standard ones, so castings with an 18 radius are estimated at at least 9,000 rubles. Tires for such rollers have a size of 235/45, their price can also be expressed in large numbers.

Alternative color combinations

The latest fashion trends have been to combine different colors to create a contrast with the body shade. It is not surprising that now you can find products not only of all kinds of designs, but also of various colors.

For example, black discs are installed on a white Vesta for contrast. And, conversely, white ice skating rinks look great against a black background. Silver (classic) is suitable for cars of any color, as it is a universal option.

Today you can find fashionable solutions in the form of colorful edging around the circumference of the rim, most often a bright red color is used. The option is also universal; it gives the car sportiness and individuality, allowing it to stand out in dense city traffic.

The best manufacturers of alternative drives for Vesta

Among the manufacturers of rollers with a radius of 17 and 18 for Vesta there are both Russian companies and foreign ones from different countries. Among them we will highlight the most popular.

If desired, you can choose alternative wheel sizes depending on your financial capabilities, design preferences and other requirements.

Should AVTOVAZ be blamed?

First of all, the wording “it turned out” in the reader’s question is unclear. The dimensions of tires and wheels allowed by the manufacturer are indicated in the operating instructions, which are posted on the official website in the public domain.

If spending on consumables for a car is so important for the future owner, it is advisable to conduct a price analysis before purchasing the car

It is worth admitting that with the price of the original 17-inch wheel (about 7,500 rubles), AVTOVAZ was really greedy. After scouring a dozen of the largest wheel sales sites, I really only found one perfect option - the KiK Flanker. It is cheaper by a thousand rubles, which saves 4,000 rubles per set. Which, in my opinion, is not so little.

After all, there is no obligation to necessarily start a complete winter kit. Are the wheels too expensive? Buy only tires. For the money that a Lada dealer asks for one disc, you can change the shoes of the entire car three or four times.

And to be completely honest, AVTOVAZ is by no means alone in the desire to make a little money. If you look for it, a similar “scam” for extra money can be found in almost any car! And the case with Vesta Cross is not the worst: for an attentive buyer it is obvious even before purchase.

Without going too far from the topic of the chassis, two examples come to mind off the top of my head. For a long time, French cars used light alloy wheels without a center hole. It is impossible to balance them on a standard tire machine. I had to look for a workshop with rare equipment. To someone in the regions - I'm sure! — there was only one way, to the official dealer with its queues and draconian prices. And for Citroen’s proprietary Hydractive suspension, non-original struts were not produced. And this despite the fact that on the last generation C5, their “snotty” and knocking could not be corrected for years, and the owners of the cars changed several sets in a row.

Finally, a little tip: write complaints and suggestions if you are not satisfied with something. Just not to the magazine “Behind the Wheel”, but directly to the manufacturer. In recent years, AVTOVAZ has demonstrated more than once that it listens to customers. Perhaps, when the number of requests reaches a critical volume, 16-inch tires and wheels will be certified for Vesta in the Cross version.

The list of the main characteristics of the car also includes the tire size, since this parameter is not only an element of the exterior, but also a factor influencing the handling, dynamics and cross-country ability of the car. Let's consider the size of the wheels of the Lada Vesta sedan, which is increasingly found on the roads.

What wheels were installed on different bodies and configurations?

It's time to look at the two main configurations of the Lada Vesta Cross and understand what the main differences in wheels and tires are.

Lada Vesta Cross 2022 with an engine capacity of 1.6 liters:

• the diameter of the central hole is 60.1 mm;
• type of fastener - bolts;
• the tightening torque is in the range of 89 – 121 Nm;
• Mounting dimensions M12 x 1.5.

Lada Vesta Cross 2022 with an engine capacity of 1.8 liters:

• the diameter of the central hole is 60.1 mm;
• type of fastener - bolts;
• the tightening torque is in the range of 89 – 121 Nm;
• Mounting dimensions M12 x 1.5.

Inexpensive and very popular are models with small wheels in size R15. Despite their attractive appearance, such wheels are not inferior in quality and differ only in their dynamic characteristics. These models can be purchased from official Lada representatives for a fairly reasonable price.

Also, when driving on such wheels with such discs, the driver will notice that the smoothness and comfort of the ride significantly exceeds the large dimensions. The disadvantage of disks of this size is their appearance. Since in the stamped steel version they do not look attractive.

Alloy wheels on the Lada Vesta Cross cost one and a half, and sometimes twice as much as stamped steel ones. But this is due to the fact that such discs are lighter due to the presence of aluminum alloys in them. When driving on such discs, you can notice increased maneuverability and controllability of the car, since the overall weight can drop quite significantly. When installing alloy wheels with a large radius, you should understand that the level of comfort will decrease, but in return the dynamic characteristics will increase.

If the Lada Vesta Cross was purchased for a family, then it is worth completely switching to R15 wheels, because this will greatly increase the overall comfort of travel. Another factor to consider is the engine power. After all, the weight of the discs directly affects the acceleration and braking of the car.

Unsuitability of disks of other Lada models

Wheel rims of size 185/55/R15 from the AvtoVAZ Grant, Priora and Kalina models cannot be installed on the Lada Vesta, even though at first glance they seem suitable. The diameter of the hole for the wheel hub of these cars is 58.5 mm, that is, 1.6 mm less.

But, even if this hole is bored on a lathe to the required size, the bolt pattern (PCD) of these products is 4x98, not 4x100, and 3 of the four mounting bolts will not be centered relative to the mounting holes, accordingly, the disk will not be aligned with the hub, and its rotation will be accompanied by beating.

About standard disks

Two types can be installed on Vesta: stamped and cast. Standard size recommended by the manufacturer: R15 and R16. Each type has its own characteristics, pros and cons.

Stamped

Stamped R15s are provided as a factory option as standard. The tire size is 175/70 R15. Choose stampings both from an official dealer and in many specialized stores.

Vesta alloy wheels

They are made from special alloys based on aluminum plus additives for rigidity and strength (strontium, titanium, magnesium). The manufacturing process for alloy wheels involves high pressure to produce a durable design. The final shape is achieved on a high-tech milling machine. The higher cost of alloy wheels is due to the complexity of production. Casting is lightweight, but the products are less resistant to mechanical damage.

Depending on the configuration, the Lada Vesta can be equipped with two cast and stamped wheels of different sizes:

• in the basic configuration R15 with tires of 175/70 and 205/60;
• in more expensive versions of the R16, stamped or cast (Luxury and Cross equipment) with 185/60 tires.

Casting can be ordered as a separate option for any configuration or purchased in specialized stores. If for stamped ones you need to pay no more than 2,500 rubles (on average 1,500), then the cost of alloy wheels starts from 3,000 (R15) and 4,000 rubles. (R16) for one copy. Depending on the manufacturer, the cost can increase several times.

Stamped discs

Stamped wheels
The simplest and cheapest option is stamped steel wheels for the Lada Vesta. They are made by stamping with a mold. External differences in parts depend on the characteristics of the stamp; in accordance with its shape, the product takes on its final appearance. The main advantage of stamping is strength and resistance to external influences: abrasions, impacts, scratches.

R15 steel wheels are provided by the manufacturer when purchasing a car as standard. Recommended tire sizes are 175/70 R15. You can purchase stampings in many service centers and stores by pre-ordering them on the store’s website, where photographs and prices are presented. The retail price in Moscow starts at 1,300 rubles per piece and can reach 2,500 rubles.

Important!

When purchasing disks, you should first check whether fasteners are included in the purchase price. Sometimes fasteners need to be purchased separately.

Appearance of Lada Vesta Cross: choice of roller

In stamped rollers, the appearance depends on which stamp was chosen for their manufacture, while in cast rollers, milling and computer graphics are used. Often, owners find other ways to make the car original, for example, installing r16 wheels instead of 15 on the Lada Vesta SV Cross. This leads to the following:

• The steering becomes better, the car holds better on the road, but when driving on uneven roads, the ride comfort decreases;
• The traction indicator in dry weather increases, but fuel consumption increases, tires wear out faster, noise insulation and stability during aquaplaning decrease.

What does the size of tires and wheels affect?

Increasing the size of tires and wheels will affect the operation of the Lada Vesta as follows:

• Increasing the disc diameter has a positive effect on the quality of steering and road holding, but reduces the level of comfort on uneven roads.
• Increasing the width of the rim will also improve steering and road holding, but will increase fuel consumption.
• Increasing the tire width will also have a better effect on handling, including on uneven roads and will improve traction (in dry weather). At the same time, gasoline consumption and tire wear will increase, and resistance to aquaplaning will suffer. The noise level will increase.