Sometimes motorists are faced with the fact that the wipers turn on by themselves (on the VAZ 2114 and other cars of the family). This problem especially often occurs in damp weather or after washing.
The reason for this lies in the fact that the common fuse block on VAZ cars is not installed very well, and its tightness leaves much to be desired.
When water hits the common unit, including the wiper relay, it closes their contacts, resulting in the switching on.
Windshield wipers VAZ 2114
When you turn on the ignition, the wipers of the VAZ 2114 turn on
Good afternoon everyone. VAZ 2114 wipers work in the off position, which could be the case. The wipers of the VAZ 2114 turn on themselves.
Similar articles
21 comments on “The wipers of the VAZ 2114 turn on themselves. The wipers of the VAZ 2114 work in the off position, which could be”
relay Although no, probably still the shift knob.
Maybe it's just a VAZ))))
This usually happens when water gets into the mounting block.
This relay closes, a little drying with a hairdryer helped me. Water got in
Water got into my black box! And the wipers also worked in off mode! try drying and sealing
Maybe water got into the motor connection plug and shorted it out. This happens
Take the relay out, dry it and put it back in
Be glad they work
The relay or block is wet. Let the photos dry overnight. I covered the top with foil to prevent water from getting in.
This is a relay, feel free to change it, it was already
I had it in 2112 because of the switch on the steering wheel
Either a relay or switch on the steering wheel
water probably washed the car
The mounting block got wet... Remove, disassemble, dry-clean and varnish the boards... Passed...
Relay contact stuck
Install a new relay and voila
Great everyone! I have a huge problem, when the ignition of my car is turned on, the wipers do not turn off and work in the first mode! replaced the switch, relay, checked the fuse box, all dry, no short circuits, where else could it be?
Often, after a car wash or rain, such a disaster as the windshield wipers turning on randomly occurs. This is especially true for cars of the Samara family. The problem is that the mounting block (fuse box) is not located in the best place, and its sealing leaves much to be desired.
As you may have guessed, water enters the block, through no power it reaches the control leg of the wiper relay, (a couple of volts are enough there) the relay is activated and the wipers begin to move. To troubleshoot the problem, you can go the long way: Disconnect the battery, unscrew the two 10 nuts (attaching the MB to the car body), lift the unit, disconnect all the plugs, remove all the fuses and relays, unscrew the screws, clean the area under the Ш 11 connector from glue. , (the place where the top plug is inserted), halve the MB and carefully pick out the board itself, then wipe it with gasoline, dry it with a hairdryer and reassemble everything in the reverse order. We take out the wiper relay, the wipers will only work in the last mode, but they won’t turn on randomly, we wait another day, the mounting block will dry out naturally and after a day the other relay can be put back. An integral attribute of every home is a chandelier. And if you are choosing an original means of hall lighting for a new apartment, then you can inspect and order on the Svetilniki website.
Com. Ua. A wide selection of manufacturers will allow you to appreciate our experience and purchase a truly valuable and beautiful chandelier. .
Sometimes motorists are faced with the fact that the wipers turn on by themselves (on the VAZ 2114 and other cars of the family). This problem especially often occurs in damp weather or after washing.
The reason for this lies in the fact that the common fuse block on VAZ cars is not installed very well, and its tightness leaves much to be desired.
When water hits the common unit, including the wiper relay, it closes their contacts, resulting in the switching on.
Good day to all! People help! When the ignition is turned on, the front wipers constantly work. The wiper intensity switch works, but cannot be turned off. I pulled out the fuse, I'm driving without wipers and without windshield washer for now because everything is connected to one fuse. Hellp, who has encountered such a glitch! It’s already spring outside, everything is running and melting, there’s enough clean glass for 100m, without wipers and washers it’s a complete mess. As I understand it, there is a short somewhere, most likely water got in somewhere. I can’t catch up, maybe someone had something similar. Tell.
Take the steering column switch apart and clean it, it should help
Put the toggle switch on and it’s like on an airplane: click and the brushes work
