Tired of creaking hinges or seals - 6 minute life hacks

Eliminating door squeaks on LADA cars

When driving on an uneven road, extraneous noise from plastic trims, linings or linings (popularly “crickets”) can appear in any part of the cabin, regardless of the make of the car.
One of the most common problems is squeaking doors. Using the example of LADA cars, we will understand how, in this case, it is better to refine the design and get rid of the “crickets” once and for all. Soundproofing doors

. This is a comprehensive measure aimed at eliminating squeaks from the door trims, as well as reducing road noise and improving the sound of acoustics. See how to make it yourself.

If the door handles squeak

. On some LADA models (for example, Lada Vesta, Granta, Kalina or XRAY), the internal door handles can be a source of “crickets”.

There are several ways to eliminate squeaks:

• Remove the linings (pry them off with a screwdriver) and glue the rubbing areas with anti-squeak (for example, Madeleine).

• Remove the overlay, cut a rectangular piece of spunbond and insert it around the perimeter. Snap the handle and cut off the excess material (what sticks out) with a sharp knife. We push the visible parts of the material inside with a toothpick.

• Cover the door handles with vinyl film. See how to do it.

If the door linings squeak

. According to reviews from owners of the Lada Vesta sedan, the source of the squeak can be plastic linings that are located in the upper part of the door trim. We deal with them in the same way. To remove the cover, pry it off with a plastic spatula. To reinstall this trim, you will need to remove the door trim, otherwise the plastic fasteners will not be able to snap into place.

By the way, sometimes it’s enough just to spray silicone grease into the gap. Have you encountered creaking in the doors of LADA cars? How did you solve the problem?

Source

If the rubber bands squeak

One of the reasons for this negative phenomenon is the loss of elasticity by rubber seals. This occurs due to exposure to aggressive detergents, temperature changes, frost, and solar heat.

In addition, the elastomers are negatively affected by the incorrect position of the doors when closed. Due to their sagging under their own weight, the adjustment gets lost. This can happen even after a minor accident. You can solve the problem using simple methods.

Cooler

This liquid has an oily base, so it can be used as a lubricant for creaking surfaces. If you lightly treat the seals with antifreeze liquid, the squeaks disappear. In the winter season, such a film provides excellent protection against freezing.

This method is recommended to be used only as a last resort, since antifreeze evaporates quickly and is not enough for a long time. Silicone grease will do the job better, but if you don't have it on hand, you can use coolant.

Aligning the door position

When the movement of the car is accompanied by squeaking rubber seals, you can diagnose their position.

To do this, you need to grab the door handle and pull it towards you. If as a result of this the creaking disappears, this indicates that the door is not adjusted correctly.

With such signs, you can suspect that it is sagging or damaged as a result of an accident. A misalignment can be determined visually by comparing the gaps. In addition, a normal door should open and close without the slightest effort. Otherwise, we can talk about a violation of its regulation.

It is quite difficult to adjust a car door on your own, so to solve this problem you need to contact specialists.

Creaking doors on LADA Vesta, how to get rid of it?

One of the weak points of this fairly popular car is the weak locking and creaking of the doors.

The car enthusiast decided to share his method of how he solves this problem. He himself said that one of the car service workers shared this method with him. The option turned out to be quite cheap. I needed to purchase a small piece of baby soap. The cost of such a piece will be 15 - 20 rubles.

First you need to thoroughly clean the door opening limiter. To do this, take a piece of natural cloth or an ordinary towel. Thus, it is necessary to remove any remaining factory lubricant from the surface. After this, you need to take a bar of soap and thoroughly rub all the parts and mechanisms with it, from all sides. Moreover, the soap does not need to be wet, that is, it must be dry. After this procedure, LADA Vesta doors will creak significantly less. In addition, the soap will also serve as a lubricant for the limiter. The soap will dry and will not slide much on the surface on which it is applied. Door locking should also improve noticeably.

What is the best way to lubricate car door hinges?

And yet, what is the best way to lubricate car door hinges? We select suitable and high-quality lubricant for hinges according to the following criteria:

• good penetration;
• long lasting effect;
• wide temperature range;
• anti-corrosion properties;
• ensuring a minimum friction coefficient;
• good price-quality ratio.

And further. The consistency of the lubricant must be such that it can combine not only high penetrating properties, but also not have fluidity, otherwise it will not be so easy to get rid of contamination of the body and interior. Of the above lubricants for the hinge mechanism, you can use any one except “Vedashka”. The often proposed alternative option - lithol, in our opinion, is outdated, and besides, it strongly attracts dust later. Also, lubrication with conventional motor oil is used only in extreme cases. If from the list of products there is no special one intended exclusively for lubricating hinges, locks and stops, then choose from the category “ greases ”! The principle of their action. Part of the product has high penetrating ability and is designed to effectively deliver the main part of the lubricant. After evaporation, a dense film remains, which not only eliminates the creaking of hinges, but also extends their service life.

It is worth mentioning products based on molybdenum disulfide . Yes, they are good for transmissions, engines and bearings. But such lubricants are not suitable for solving our problem, since a layer of dirt quickly forms, and besides, this product is very easily soiled.

Silicone lubricants for car door hinges are good, but they are poorly resistant to washout and high temperatures. It’s a completely different matter if silicone is part of a multi-component product - it has almost no drawbacks.

How to get rid of squeaking Lada Vesta doors

Gentlemen, whoever's front lamp clangs on bumps, please read this carefully.

First, of course, you need to check the tightness of the bolts securing it to the roof by removing the outer frame (the frame is on clamps, it’s not difficult, you need to press something on the front clamp and gently pull it down). This helps some people. In my case, this reduced the frequency of the sounds made, but did not get rid of them.

Experimentally (I removed the outer frame and hit the sun visor on the roof) I found that the housings of my SIDE diodes, which are made in the form of hemispheres, are rattling (the central diodes do not have housings). What I did next:

1) I unscrewed two screws, released the latch and let the lamp hang on the wires (don’t worry, it’s light, nothing will happen to it) 2) I discovered that the electronic board itself is attached to the plastic case using solders, so in case of a malfunction the lamp is always replaced , restoration is not provided in the service 3) I found translucent solders (2 pcs.) in each of the hemispherical housings of the side diodes. The reason for the chatter is the play between the solder cap, which prevents the case from falling out, and the circuit itself, and the play there is literally a fraction of a millimeter. 4) Carefully coated all solder joints with Moment-gel glue or similar, rubbed it with a toothpick or match along the perimeter of the solder joint 5) That’s it! The annoying rattling noise has completely disappeared!

I can’t attach a photo yet, but I described everything in sufficient detail. As soon as you start doing it, you will immediately understand everything.

In my case, on one of the diode housings the backlash was much stronger than on the other, from which I conclude that someone may not have it at all - apparently just a manufacturing error. And I myself had the lampshade replaced under warranty; I don’t remember this happening on the old one. Well, for those who are pretty annoyed with the rattling of the lampshade, I hope my method will help you.

Eliminating squeaks in the cabin

#elimination of squeaks Good day, I decided to write about cricket squeaks in the Vesta salon. Yes, I’m not the first and I won’t be the last, but still. Car