External door handles (set of 4 pieces) for VAZ Vesta, X-Ray

Lada Vesta is rightfully considered the best Russian car...

...and is increasingly popular with customers. But this modern model is not immune to problems with door handles, which are typical for all cars produced by the AvtoVAZ concern. Let's look at the main malfunctions of Vesta's door mechanisms and learn how to fix them ourselves.

Typical problems with Lada Vesta door handles

• Most often, door handles on Vesta jam or do not return to their original position. This is especially true for the driver's door, which is used more intensively. This problem sometimes occurs immediately after purchasing a new car. The manufacturer knows about this defect and replaces these parts in the warranty service without problems, so if such a malfunction occurs, you can simply contact the service center, where they will fix it for you. But you can cope with this problem yourself.
• In addition to jamming, many drivers are worried about such a nuisance as the constant squeaking of internal door handles. This intrusive sound can be eliminated by installing additional insulating material or sealant from the inside, which will require dismantling and disassembling the internal element.
• Another common problem is damage to the paintwork near the outer trim. To prevent them from scratching the paint, it is necessary to fix the gasket between the moving element and the body, which can sometimes not be held securely. In order to do this, you need to glue the gasket under the rubbing parts using double-sided tape.

What to do if the handle does not open - reasons

Sometimes problems with the external elements of Vesta lead to the fact that the door completely stops opening from the outside. The reason may be one of the malfunctions that we mentioned above. In this case, you will have to change the part under warranty or yourself.

The second reason why a car door does not open or close is a malfunction of the lock itself. Even with the rod working normally, it cannot be lowered and raised smoothly, since the lock mechanism is jammed. To solve the problem, it is often enough to lubricate the rod a little and design the part properly so that the lubricant reaches its destination.

Removing the door handle on a Lada Vesta car

We will consider the process of removing the external handles, which must be done in case of any type of breakdown, in stages.
Link on topic: Head unit MMS Lada Vesta.

1. Looking at the handle from the outside, it seems that it does not have any fastening elements and it is completely unclear how to dismantle it. In fact, access to the fasteners is located under a rubber plug at the end of the door.

This plug must be carefully pryed with a hard object and pulled out.

1. There is a bolt inside under the plug. It needs to be unscrewed using a T15 key. There is no need to completely unscrew the screw; you can simply loosen it a few turns - this will be enough.
2. Next, you need to carefully pull out the plastic stopper.

It should come out easily, without any extra effort. The plastic here is quite fragile, so you need to act carefully. If the element does not slide out, you can spray a little liquid lubricant, such as VD-40, into the gap and try again.

1. After the corner is removed, the door handle must be moved slightly back and towards you. First the back part is released, and then the front. You also need to act carefully, with smooth movements.

The process described concerns the passenger handle. If you need to remove the driver's, then first you need to disconnect it from the lock that is located in it. To do this, the door cards are removed to open access to the door rods, and the fastenings are carefully disconnected.

The rear elements are removed in the same way, only the plug is located under the door seal, which can simply be bent a little.

How to remove interior door handles on Lada Vesta?

Internal handles often bother drivers with squeaking and unpleasant squeaking noises while driving. This problem can be solved by using a gasket inside the Madeleine part or automotive sealant. You must act in the following order:

1. Remove the plastic cover. To do this, you need to carefully pry it over the edge with a flat object and remove it. It is better to use special plastic spatulas that will not damage the decorative coating of the door. This interior element does not have any fasteners in the form of screws or bolts, so it is very easy to remove. The main thing is to act carefully so that the thin plastic does not break.

Related link:

Features of replacing the windshield on Lada Vesta

1. After the handle is dismantled, you need to carefully glue the joints with insulating material. To do this, you can use madeline, a special anti-creaking noise-insulating tape that is sold in car dealerships, or fabric electrical tape. It is necessary to glue along the entire perimeter, excluding the clamps, so that the part can hold on. Some drivers use sealant instead of insulating material, but after this treatment it will be difficult to dismantle it again if necessary, and it may need to be completely replaced.
2. Reinstall the handle in the reverse order. After gluing it will snap tighter, and you need to tighten it well and press it. We check that everything is done correctly by closing and opening the doors several times.

Internal handles

Vesta interior door handles
To change interior door elements, you will have to spend even less time than on external ones. Let's look at the step-by-step instructions for the driver's door:

• Decorative trim is completely removable;
• Next, the screws are unscrewed to secure the part to the door;
• The handle is carefully removed from the door panel;
• The drive rod is removed from the holder;
• Disconnect all wires and remove the element;
• To install a new part, proceed in reverse order.

Before starting work, make sure that there is really a need to completely remove it from the door. Very often, troubleshooting problems in interior elements requires only removing its top cover, and further work is carried out on the inside of the part. This is the method that is used if it is necessary to eliminate the creaking of opening elements.

How much will it cost to replace Lada Vesta door handles?

Many Vesta car owners prefer to completely replace them instead of repairing them. Sets of new parts are sold in car dealerships everywhere, and purchasing the required color is not a problem. You can order the necessary spare parts on the Internet, for which you need to know their article number.

Marking and cost of Lada Vesta door handles:

Related link:

Review of the Lada Vesta car

The cost of a set for four doors is approximately 2500-2700 thousand rubles, depending on their color and point of sale. Craftsmen charge an average of 500 rubles for installing door handles, but knowing how to remove a Lada Vesta handle, you can make the replacement yourself.

Handle price and article number

Vesta comes equipped with European-style handles as standard. If replacement is necessary, you can order the same kit in the store or from any official dealer. The price of a set of 4 painted external parts will range from 750 to 2200 rubles. To order, use article number 8450007739.

Salon handles can be sold as a set, but in two pieces, or individually. The average price of 1 part is 400-600 rubles. The article numbers of the interior unlocking elements differ according to the side on which they are installed. To purchase right handles you need to use the number 8450007743, and to buy left handles - 8450007744.

When ordering a set, pay attention to the color of the purchased parts. If interior elements are sold in silver, then the exterior ones can be matched to the color of the car, avoiding additional repainting.

conclusions

Making minor modifications to the door handles of a Lada Vesta car is not particularly difficult. This does not require any special skills or complex tools, so anyone can cope with the task. The driver just needs to remember that removing external and internal elements requires care and caution, since the plastic on Vesta is quite fragile.

Complete replacement of handles if necessary is also not a problem. In online stores or on shelves, you can purchase sets of a suitable color, or cover parts that have lost their appearance with plastic covers.

Door handle covers

Often, in order to hide defects that have appeared during operation, car enthusiasts install chrome plates on the door opening elements of Lada Vesta. Such a decorative element is inexpensive, but gives the car a fresh look. The linings are sold as a set, and you can find them for external and internal ones.

Installing the element does not require special knowledge or skills. The cover is attached to the factory part using double-sided tape, sealant or other adhesive material. Be careful during installation to avoid problems in the future. If the chrome door handle trim is not installed tightly enough, dirt and moisture can get into the resulting cracks, which means there is a risk of rust.

Before purchasing items, study the offers of different stores. Some companies seriously inflate the price and instead of several hundred rubles, you have to pay a couple of thousand for them. However, the quality does not change. You can only pay a large amount for linings made of stainless steel, since their service life is long and their wear resistance is superior to chrome ones.