How to install fog lights (PTF) on Lada Vesta

03 February 2018 Lada.Online 146 304 26

The manufacturer installs fog lights on Vesta only in the “luxury” configuration. The situation is similar with other AVTOVAZ models, so self-installation is one of the popular modifications. Do you know that installing PTF on Vesta is not as easy as on other modern Lada cars?

Choice of performance

First of all, you need to decide how the fog lights will be installed on the Lada Vesta - by an official dealer or independently.

Installation of PTF by a dealer - a condition for maintaining the right to warranty service - is carried out in the scope of work provided for when producing top versions of Lada Vesta, and, accordingly, including the entire list of components approved by the manufacturer. Even without taking into account the cost of performing the work, the amount turns out to be impressive.

The high cost in this case is due to the complexity of installing the Lada Vesta PTF, since the electronic support circuit of this car differs significantly from the electronics of previous models of the Lada line (Granta, Priora, Kalina) - the fog lights on Vesta are controlled from the steering column lever-switch by turning the sleeve-tip, which functions regardless of the position of the lever.

The reason for the high cost of installing a PTF by a dealer is the additional electronics unit, installed only on luxury versions of the Lada Vesta. This block is an intermediate link on the signal path from the switch to the headlights, which displays information about their inclusion on the dashboard. And the installation of this device also entails expensive changes in electrical wiring.

If the car’s warranty period has expired, then equipping the sedan with fog lights is possible using a much simpler scheme, which includes, in addition to fasteners, the ability to easily turn on/off the PTF with a button on the front panel.

Is this really necessary?

Road safety comes first! Installing fog lights on Vesta will improve this indicator (subject to proper adjustment) during bad weather conditions, when visibility is significantly reduced. Thanks to the beam angle and beam strength of these headlights, the driver can see the road better. And it’s easier for other motorists to notice such a car.

PTFs are also useful at night, they allow you to avoid dangerous situations on the roads, since the driver can see not only the space in front of the car, but also beyond the curb or side of the road.

From an aesthetic point of view, the Lada Vesta with fog lights looks more expressive and respectable.

Selection of fog lights

The standard PTFs of the luxury Lada Vesta configuration are equipped with H16 lamps with a power of 19 watts, which cannot be called the optimal option. The fog lights listed in the table below have higher performance and, especially Valeo, have proven themselves when installed instead of standard ones.

In addition to headlights, you must purchase the following materials:

• 4-pin relay – 1;
• headlight on/off button - 1;
• protective corrugated cover (tubing) for wire - 5 m;
• wire - 5 m;
• 16 A fuse - 1.

Removing the front bumper

Considering the massiveness and aesthetic component of this element in the exterior, dismantling the front bumper should be done carefully and strictly according to the instructions.

First of all, you need to disconnect and remove the battery from under the hood. Then, using a “10” head, unscrew the 2 bolts securing the air filter unit, which also hold the upper part of the bumper.

The registration numbers are removed, under which there are 2 screws securing the bumper to the central beam. Using an L-shaped TORX “20” key, unscrew these 2 screws and 2 of the same self-tapping screws that attach the bumper to the wings in the wheel arches.

Then, using an L-shaped TORX “30”, unscrew 4 screws securing the lower part of the bumper, and TORX-20 – 2 more screws securing them to the side panels on each side.

After this, the bumper is pulled forward, alternately on each side of the wheel arches, until its latches come out of the mounting sockets.

The bumper remains hanging on the top four TORX-30 key bolts, of which the central one (opposite the hood lock bracket) is unscrewed last, while keeping the bumper from falling, after which the accessory is completely disconnected from the car.

It is advisable to use this situation to simultaneously clean the radiator from insects and debris.

We dismantle the bumper on the Lada Vesta

The product is quite massive, so there is a risk of damage to the paintwork when removing it. Here we use all available precautions as much as possible.

1. Disconnect the battery and remove it.
2. We prepare the place where the removed bumper from the Lada Vesta will be placed in advance by spreading a soft cloth.
3. The lower edge of the bumper is attached to the fender liners using 4 screws. They can be twisted.
4. We also unscrew the two screws that connect the product to the lockers.
5. The upper perimeter of the bumper is held in place by six bolts, which we also remove.
6. We unscrew a couple of bolts under the license plate.
7. We pull the body element towards ourselves, gradually allowing it to disengage from the side brackets.

Preparing seats for the installation of PTF

By placing the bumper on the soft canvas with its front side, you gain access to the fastenings of the niche plugs in which the fog lights are installed.

The front bumper of the Lada Vesta Optima configuration is equipped with plugs that are not designed to attach PTF to them, and does not have any additional fasteners on the rear side.

In this case, it is necessary to purchase brackets for installing fog lights (2 pieces included - right and left).

If fasteners are present, they must be removed to get to the plugs.

After dismantling the PTF mounting brackets, remove the plugs held in the grooves by latches and self-tapping screws.

In the removed plastic plugs, using a drill with a core drill, holes are cut out with a diameter corresponding to the existing contour or selected headlights, after which the cut edge is processed with fine sandpaper and the parts are installed in their standard places.

Let's sum it up

Do-it-yourself installation of such an element in a car as PTF in LADA Vesta allows you to save a lot of money (more than tens of thousands). Auxiliary materials and devices for installing fog lights will require the owner to part with 5-6 thousand rubles. The procedure will take several hours to complete, but now the car will not only look good, but will also provide improved visibility in bad weather and at night.

A fog lamp (FFL) is a necessary part of the external image of a car. More importantly, such lights should illuminate the road space for the driver even in heavy rain and snowstorms. The part must dissipate a white or light yellow tone, which forms a horizontal beam spreading over the route. Their design is such that they do not affect the upper layers of fog, and, therefore, improve visibility. In the event of a breakdown and the desire to repair the lights on their own, the owner will need a kit for connecting the PTF to Vesta with wires, relays and special buttons. This also includes the bracket.

Most of the latest products from AvtoVAZ have holes and fasteners for installing PTFs, but the plant itself practically does not install them. There have been numerous complaints about fog lights from the manufacturer. Car owners note that the lighting from them is very weak. Hence the rational solution: it is better to buy high-quality PTFs for Vesta and install them yourself.

Connecting fog lights

The PTF power button is conveniently located on the central part of the console or to the left of the steering column in an existing recess. The hole for the button, depending on its configuration, is drilled or cut out, followed by careful processing of the edges without damaging the finish.

The wiring from both headlights should be brought into the cabin in the area of ​​the pedal assembly; for this, it is convenient to route the wire of the right headlight along the transverse box between the side members.

To connect the headlights, it is advisable to use the classic circuit used in previous models of the Lada line (Priora, Kalina, Granta), simplified - take the power from the clamp bolt of the positive terminal of the battery.

This method will minimize interference with the vehicle’s electrical circuits and the cost of purchasing components.

Tuning daytime running lights

On the Lada Vesta, the manufacturer uses double-filament lamps in the side lights and daytime running lights. If instead of them you install LEDs modified in a certain way, then the yellow color of these lights, which is ineffective during the day, will change to a brighter white with blue.

Before performing this operation, you need to familiarize yourself with the pinout of the Lada Vesta daytime running lights sockets, since on this sedan it is non-classical:

• on one side of the cartridge there should be a “-” in the form of two contacts or one common one;
• on the opposite side - “+” for side lights and “+” for daytime running lights.

When purchasing LEDs, you must ensure that the polarity of the lamp base and the Vesta socket match. If such LEDs could not be found, a way out, which is not always harmless, may be to bend the contact pins of the elements according to the indicated pattern.

Headlamp device

A block headlight is a design development that allows you to combine lamps in a single housing, each of which would do its own job. The light bulbs on the Vesta in the headlight unit have their own fastening elements, as well as places for installation.

Headlamp unit. Photo source: https://deilo.ru/chelabinsk/transport/lada-vesta-fara-perednyaya-levaya-402370297079657.html

The headlight contains the following lamps:

• halogen low beam;
• halogen high beam lamps;
• turn signal lamps;
• daytime running lights and dimensions.

The convenience is that, if necessary, the owner can replace each light bulb with his own hands without removing the entire headlight, and there is also the opportunity to buy a complete headlight unit without purchasing individual elements.

What kind of high and low beam lamps are on the Vesta?

Lada Vesta bulbs for high and low beam meet international standards and are not inferior in quality to foreign analogues. AvtoVAZ uses the following lamps on Vesta:

• near – H7;
• distant – H1.

The consumption of both is 55 W. Despite the general power rating, they differ in base.

Lamp socket for headlight

Lada Vesta light bulbs have their own markings. Their designations are certified according to EEC:

• near – H7;
• distant – H1;
• turn signal – PY21W;
• daytime running lights (DRL) and dimensions – W21/5W, brand – Vanssi;
• PTF – H16.

These names are easy to find in automotive stores or service centers.

PTF selection

It’s one thing if you decide to install LED daytime running lights on Vesta - here the choice will be much less hassle. However, when installing DRL on a Lada Vesta, it is necessary to take into account certain standards, for failure to comply with which the driver faces a fine. We talked in more detail about all the nuances of choosing DRLs in this article.

But when buying a PTF, you also need to take into account certain nuances, including:

1. Appearance of optics. Everyone knows that in our market today it is very easy to fall for a fake, the operating efficiency of which will be significantly lower than that of the original headlights. Before purchasing, carefully inspect the fog lights - their housing in any case should be as airtight as possible and tightly fixed. Also pay attention to the material itself - it must be durable, since it will have to work in different operating conditions.
2. Lenses. If we talk about lenses, they should be glass. Don’t even think about choosing a PTF with plastic lenses, because if even the smallest pebble gets on them while driving, the lens may crack.
3. Filter color. As for the light filter, it is desirable that it be yellow. As practice shows, yellow fog lights can better cope with cutting off the long light stream that appears during fog. But it should be borne in mind that a yellow tint can ruin the appearance of the vehicle, so, as an option, you can use special lamps in the PTF.
4. Disassembly of the headlight. Another point that you need to pay attention to is the possibility of disassembling the headlight yourself. Sooner or later, any car owner will have to face the need to replace lamps, so if it burns out, you just need to replace it. If the headlight is not collapsible, then it will have to be changed completely (the author of the video about the development of LED headlights by domestic designers from Barnaul is the VESTI ALTAI channel).

How do fog lights work?

The presence of fog lights in a car gives the driver the opportunity to feel calmer while driving in poor visibility and fog. Due to the location of the PTF in the lower part of the bumper and below the level of the head light (and fog, as you know, spreads above half a meter from the road), the light passes through the curtain and is visible to other road users.

LED fog lights for Vesta. Photo source: https://www.drive2.ru/l/476399147935597172

Also, such headlights have a clear cut-off line due to their placement and the shape of the reflector, and the light-optical design has a screen of direct rays that prevents light from scattering and reflecting from small drops.

Installation and connection of PTF

If everything is clear with the choice of fogs, then let’s move on to their installation. Please note that installing optics involves connecting them to the unit, so if you do not have experience in this, it is better to immediately contact an electrician.

So, how to install fog lights on a Lada Vesta:

1. First of all, the battery is disconnected and the front bumper is dismantled, and then it is necessary to remove the plugs installed at the location where the PTF is installed. After removing the plugs, holes are cut; for this purpose, you can use a regular stationery knife. Just do everything carefully to prevent scratches on the bumper.
2. Next, the optics are fixed to the plugs; for this you can use simple self-tapping screws.
3. Now you should install a button to activate the optics in the center console of the cabin. Choose any convenient place for us, as an option, the button can be placed on the steering column, on the left, near the trunk control button.
4. After the installation steps are completed, the optics must be connected correctly. The wiring from the right lamp must be laid in a steel box, after which all cables must be pulled through a special technological hole located next to the pedal assembly. If we talk directly about the connection diagram, then for this you can use the universal option presented below. It is necessary to take load power from the battery through the bolt, which is supplied to the relay through the safety element.
5. The “+” terminal is taken from the side light fuse directly in the block; for this you can also use the plus from the cigarette lighter. As for the direct installation of the relay, it is done either in the engine compartment or in the passenger compartment.

How to install fog lights on Vesta with your own hands

Replacement or initial installation of PTF on Vesta should be carried out in specialized workshops, but if it is not possible to go there, then you can do the work yourself:

1. Remove the button cover on the central panel above the climate control and dismantle the board.
2. Replace the board with a four-button one and install all the buttons in place, including the new one for controlling the fog lights
3. Remove the bumper by unscrewing 2 screws on the fender liners, 4 screws near the wings and the same number in front of the protection below.
4. Next, unscrew the 2 screws numbered and 5 under the hood, but leave one to hold the bumper.
5. By removing the clips under the headlights and disconnecting the ambient temperature sensor, you can unscrew the last screw of the bumper and remove it completely.
6. In place of the plugs, install the cladding assembly.
7. Attach the brackets to the press washers, and the headlights themselves to the screws, but the bottom one should be shorter so as not to damage the frame.
8. First install the bumper and, using a set of radio components and electrics, connect the wiring according to the formula.
9. Install a square-shaped relay, pulse if desired, into the fuse block, making a tap from fuse f10.
10. Finally install the bumper.

When performing these operations, inexperienced car enthusiasts may encounter a number of problems.

Headlight tuning: options

Now let's briefly talk about optics tuning. As a rule, car owners are faced with the need for tuning if they want to improve the appearance of the vehicle.

So, PTF tuning options can be like this:

1. Installation of lensed xenon lights. Installing xenon involves installing an additional unit. This tuning option will improve the visibility of the fog lights. But it should be borne in mind that it is better to install xenon if the headlights in your car are xenon.
2. Installation of LED bulbs in lanterns. A cheaper, but no less effective option compared to xenon.
3. Installing eyelashes on lanterns. This option is one of the most budget-friendly and simplest.

Review of Manufacturer Prices

Why don't you have fog lights?

On modern domestic cars, such additional equipment is installed exclusively in luxury configurations or as an additional option. If our Vesta did not have foglights when we purchased it, then we will need to do the installation ourselves.

It is important to remember one immutable truth - even installing such a small thing as a pair of headlights automatically leads to loss of warranty.

There can only be one way out, try to perform the so-called re-equipment to a configuration an order of magnitude higher than the existing one. You will need a standard kit from AvtoVAZ, which includes:

• Two headlights ( 261500097R );
• Front wiring kit in harness (8450006983);
• Left fastening element (8450006277);
• Right fastening element (8450006276);
• Switch kit (8450006924);
• Body electronics unit ( 231A08052R );
• Instrument panel wiring harness kit (8450030715).

PTF installation cost

It would be good to first think about how much such a procedure would cost, because on Vesta an installation of this kind is a rather complicated and time-consuming task.

The cost of pleasure, at the time of writing, is approximately 50,000 rubles . If you have somewhere to add 15-20 thousand, then you can safely go to the dealer and install it on site. If something happens, you can always fix any damage under warranty. Has the desire to save money taken over? We do everything with our own hands.

Cost of installing a PTF at a dealer?

Official representatives of AvtoVAZ consider the installation of lighting equipment as an upgrade of the equipment of the Lada Vesta car to the level of the maximum configuration. The cost of the procedure reaches 60 thousand rubles.

The exorbitant price is explained by the complexity of performing the process using the dealer method, which also involves the use of original production parts. The cables alone will cost the owner about 20 thousand rubles. Therefore, many car owners are interested in how to install headlights themselves.

Do-it-yourself installation allows you to achieve significant cost savings. The only unpleasant moment here may be the possible cancellation of the warranty.

Preparation for equipment installation

The main difficulty is that the electrical system design of this machine is significantly different from previous versions.

The lighting will be controlled using a switch mounted under the steering wheel, but does not have suitable positions for fixing the light output. The electrical signal comes from the lever through an additional unit, available only in the luxury version. So the most acceptable solution is to install a kit with a separate connection and a special button output.

List of tools needed for installation:

• pliers;
• screwdriver with Phillips bits;
• self-tapping screws;
• 76 mm bit for drilling holes;
• stationery knife;
• a set of keys for removing the bumper and installing optics.

What difficulties does the master face during installation?

Unlike previous generations, Lada Vesta has a new system of electrical power supply, distribution, processing and signal transmission.

Standard control of fog lights is implemented via the steering wheel paddle. The activation signal does not go directly to the fog lights, but to the EMM control module. After which the unit redirects the signal via the CAN bus.

Installation according to the described scheme is quite expensive; the cost of the service including consumables reaches 55 – 65 thousand rubles. The price is prohibitive for most car enthusiasts. In this regard, owners are forced to install PTF themselves.

Beginning the installation of the lighting kit

This is how we will carry out the work in a simple and reliable way, while using a separate electrical circuit.

We remove the front bumper, carefully cut out holes with a diameter of 76 millimeters in the places where the plugs are located.

A sharp knife with a harder blade or a metal crown of the appropriate size will come in handy. We insert the headlights into the holes, securing them to the right and left brackets using self-tapping screws 15–20 millimeters long.

We install a switch button inside the car; you can use a standard VAZ one from LADA 2114, placing it next to the vertical adjustment wheel for the optics. You can draw a conclusion to the standard switch from Vesta, which will be without fixation, located just below the audio system.

We lead the wiring from the headlights through a metal corrugated box to the hole located in the area where the pedals are located. From there we draw output to the button.

Wiring diagram

We use the same principle as when installing Priora and Granta equipment.

The 12V load power for the relay must be taken from the battery using an M6 bolt, directly through the fuse.

Plus it will be possible to take it where the size fuse is located in the mounting block, from the cigarette lighter.

We mount the relay where it is most convenient: in the engine compartment or inside the cabin. So we got off with a “slight fright” - we interfered minimally with the electrical part, maintaining the warranty on Vesta.

Installation diagram for LUX version

conclusions

This article discussed the simplest, but most expensive method of installing anti-fog equipment.

In practice, especially if your Lada Vesta is no longer under warranty, everything can be done at much lower cost using plastic corrugation, simpler wiring, a 16-amp fuse, and a 4-pin relay. In general, the installation sequence will not differ.

By choosing the most suitable method, you can equip your car with enough light for comfortable driving in the dark, when visibility is very limited.

Fog lights, like the main optics of a car, play an important role in creating high-quality lighting. Fog lights are especially important in poor visibility conditions. For example, during rain, heavy fog or snowfall. As for the Lada Vesta, the situation here is such that fog lights are provided only in the “luxury” configuration. Therefore, installing PTF is relevant for this family of cars. If you are determined to install fog lights yourself, then this review is for you.

It must be said that installing PTF on Vesta yourself is somewhat more difficult than on other Lada cars. On the other hand, you will thus save quite a decent amount. So, for example, an official dealer can charge you up to 10 thousand rubles for installation, depending on the region. If you do not have such an amount, then it is better, of course, to carry out the installation yourself. Therefore, be patient and have enough time.

To install fog lights on Vesta you will need to purchase:

1. The fog lights themselves - here you have a choice: take Original Valeo PTFs or a good quality analogue or Tune-auto PTFs (and look for bulbs) or take Chinese ones of dubious quality (there were precedents when they simply melted).
2. Brackets for installing PTFs are actually what the fog lights are directly supported on. It is very difficult to find original brackets; AvtoVAZ does not release them on the free market. Analog brackets are very suitable; they are of decent quality, completely replicate the geometry of the original ones, and they are always in stock.
3. PTF facings. Here the situation is simpler - you can cut holes in your trims for fog lamps with a diameter of 76 mm, or purchase luxury trims for fog lights.
4. Wiring. You will need a set of wires to connect PTF Vesta. Everything is more complicated here, since there are no special buttons or space for a button to turn on the PTF in the cabin.

The first thing you will encounter when connecting is the electrical circuit, which is completely different from Grants or Priora. First of all, on Vesta the foglights are controlled via a steering column switch, which does not have a fixed position for turning off the PTF. At the same time, the signal to turn on the fog lights does not go directly to the headlights, but through a special unit, which is present only in luxury cars. Therefore, in order not to damage the car and not waste an extra couple of hours, we recommend adding a separate button for the PTF.

Now you can proceed to the direct installation of the PTF. First, remove the bumper and replace the existing PTF trims with “luxury” ones or carefully cut out the plugs using a utility knife or a 76 mm crown. Then take the fog lights and secure them to the brackets using self-tapping screws, and the bracket directly to the bumper.

Connection is the next and very important point. To do this, stretch the existing wires from the kit to each of the fog lights, the free end is connected to the relay (it can be installed in the mounting block or in the engine compartment). Now we connect according to a universal scheme, like Kalina or Priora. Take the “+” from the battery to the relay, and you must use a fuse. There you can take the “-” mass directly from the “negative” terminal, or it is better to find a nut nearby and screw it to it. The control plus on the relay comes from a button from the passenger compartment. Now stretch the wire for the button into the interior and install the button (the most convenient button for turning on the PTF 2109) on the decorative cover of the fuse box next to the headlight adjustment unit.

Finally, do not forget to check the functionality of the PTF and put the bumper in place.

Using such a circuit, you will minimally interfere with the electronics of the Lada Vesta, which means you will not harm it. The basic rule for installing PTF is to try to be as careful and attentive as possible, then you will get a positive result. Properly installed fog lights will provide you with not only proper visibility on the road, but also safety.

Lada Vesta Furia Roja › Logbook › Replacing the factory PTF with PTF Osvar.

Let's start with the fact that there were few factory PTFs, and I wanted a little more light from the PTF. Readings on various forums suggested three options: installing bi-lenses with xenon instead of PTF, installing PTF with N11 lamps, and installing Russian-made PTF with N1 lamps. Of course, I wanted the first option since it was a very bright + long-range mode, but the price tag here was 6 thousand+ in total and perhaps a little communication with traffic police officers, which I didn’t really want. The second option was more affordable, but the dubious quality of the PTFs themselves and the high cost of N11 lamps, compared to N1 lamps, gave rise to some doubts. The third option is the Russian PTF Osvar for the H1 lamp base. High-quality housing, iron reflector and glass diffuser. Of course, the third option won, so to speak, cheaply and angrily! And so let's start, ordered: Lada 8450006276 right fog light bracket Lada 8450006277 left fog light bracket Hella 4RA 933 332-101 relay, operating current Osvar 36023743 -2 pcs. fog lamp renault logan/sandero/duster Osram 64150NBU-HCB incandescent lamp, high beam headlight; incandescent lamp

I ordered everything on emex

relay from hella

I ordered the relay from Hella, I don’t know why), apparently Bosch were expensive. I used the relay to unload the standard wiring, since the standard PTFs had H16 lamps with a power of 19 watts, I didn’t take any risks and took the power from the battery, the standard PTF wiring is only controlled.

PTF themselves from OSVAR

On the left is Osvar, on the right is Valeo (factory)

The PTFs look very high quality and well assembled; the PTFs already have lamps. But he still advised me to coat the glass with sealant; after 10 thousand runs, a little sand appeared in the right PTF when I washed it generously. There were already lamps in the PTF.

simple lamps and standard brightness

Brackets for PTF

I ordered the brackets specially, because I knew that they needed to be modified, and I didn’t want to disfigure the factory ones.

Bracket already with PTF

As it turned out, you need to modify it a little, filing the plastic a little and the PTF fits like a family!

There is nothing special to explain about connecting the wiring; relay contacts 85.86 are taken from the wiring going to the PTF power supply; contact 87 is taken from + to the battery through the fuse. Contact 30 goes to the PTF power supply

I also threw a mat under the battery, purchased earlier for 50 rubles

We also purchased brighter lamps in PTF, high and low.

In the PTF I installed the previously installed PHILIPS H1 X-TREME VISION +130 in the far range, and in the far range I installed the OSRAM H1 NIGHT BREAKER +110. I haven’t installed the neighbor one yet, but they are waiting their turn PHILIPS H7 X-TREME VISION +130

And so, we begin removing the bumper to install the PTF

photo from the Internet Installing fog lights PTF Lada Vesta

We unscrew all the bolts that are shown in the picture, unclip the bumper from the wings, carefully and slightly pull the bumper towards you and turn off the temperature sensor in the bumper. Next, we place the bumper on a flat surface and dismantle the standard PTFs, which are held on by 2 screws, and also installed the new PTFs on 2 screws

In many places, IZH Full size is stamped on the plastic; in the back, there were different lamps from the factory. on the left was GE, on the right was Philips (the lights were the same)

For the experiment, only one PTF was installed and the new PTF was adjusted using the factory PTF

Full size, passenger side OSVAR, driver's side VALEO

We configure the PTF and see the difference

Full size difference in light on face

I made the adjustment the next day and installed the second PTF and also adjusted it.

And now night photos of the headlights:

Only PTF

Full size light more white

PTF + Middle

Full size headlight low beam lamps are still factory

PTF+Near+Far

Full size satisfied with the lighting

I am pleased with the result of the work done! The lighting just got better! I recommend! Thank you all for watching, like and repost!) Criticism is welcome!)

Fog lights are an invariable attribute of a modern car. Unfortunately, AvtoVAZ equips models with pre-installed PTF only in luxury versions. Owners of basic modifications are forced to upgrade the car themselves and order paid services from a service station.

What is the reason for installing fog lights?

• road safety in fog, snowfall, and reduced visibility;
• aesthetic appearance: the car looks completely different, a certain element of tuning, modernization.

Benefits of fog lights

These headlights got their name because they are able to provide visibility in foggy conditions. This natural phenomenon minimizes visibility and can easily lead to an accident. It is also difficult for the driver to do without fog lights in rain, snow or blizzard conditions.

The design of such lighting devices as dimensions, low and high beams does not allow leveling the effect of fog. This fact remains evident even when installing the most powerful types of lamps (LED, xenon). The action of the above light devices does not help due to the fact that the rays collide with microscopic drops of H2O in the form of steam or snowflakes, and are reflected or scattered from this. As a result, a translucent veil is formed and significantly impairs visibility. In addition, a dazzling effect is created. Fog lights have trump cards and advantages over main lighting. After all, PTFs are located almost at ground level. But the fog condensate does not reach this level. Therefore, we get the effect that the headlights are directing light under a veil of fog. In addition, the upper beam received from the PTF light has a clear boundary horizontal level and does not allow reflection at all from drops of fog that fall into the driver’s field of vision.

Another advantage of fog lights: they have a wide lighting spectrum. Due to this, the side of the road remains illuminated even during fog, which makes driving on roads with sharp turns much easier. Also, these lighting devices allow drivers of oncoming vehicles to see the dimensions of the car during bad weather. The color of the flashlight does not affect the quality of dispersion, because during fog all colors from the spectrum are scattered similarly. Because of this, the fog appears white or gray in sunlight.

Due to the above advantages, we can conclude that the presence of fog lights is practically necessary for every car. Two main advantages from installing this lighting equipment:

• improving driving safety;
• exterior decoration.

The driver drives calmer and more confident, knowing that in case of bad weather visibility will not be limited. PTFs also help with night driving. They can be used as an additional lighting device. And the fact that fog lights decorate the exterior of a car is especially relevant in the case of the Lada Vesta. After all, with them the design of the sedan is solid and complete.

Most Vesta consumers, when purchasing a non-top version, tend to equip the car with foglights.

Replacing the lamps inside the headlights

The original halogen high and low beam devices on the Lada Vesta stand out for their high-quality assembly and good light. The headlights illuminate the entire road in front of the car and at some angle on the sides. When replacing them, remember that halogen lamps must not be touched with hands. All manipulations are carried out with gloves on your hands, or even better, holding the base. Otherwise, there are no difficulties when replacing light bulbs or headlights. To do this, you don’t even have to remove the headlight itself, the bumper, or perform complex manipulations.

Open the hood and approach the headlight from behind. You can see 2 lamp covers (low and high beam). They are very easy to unscrew by turning clockwise. Then you need to disconnect the wiring and release the socket from the spring retainer, remove the socket and replace the burnt out lamp. The DRL, turn signal and side light bulbs are much easier to replace. To gain access to the bulb, turn the socket clockwise and then remove it. The burnt out lamp is ready to be replaced. Assembly is carried out in reverse order. Now in more detail about all types of lamps.

Difficult installation situation

You need to figure out how to install PTF for Vesta. If the driver decides to install fog lights on Vesta from an official representative of AvtoVAZ, the price of the issue will be very high. In other words, the dealer’s installation of additional lights is carried out in the only possible way: partial modification of the vehicle’s equipment to a top-end one.

This procedure will cost the customer more than 60 thousand rubles. Such an exorbitant price is due to the fact that it is necessary to purchase original factory parts that make up the PTF system.

If you add up the price of all the components, you already get a tidy sum. We should not forget about the cost of installing this equipment. In total we get the same 60 thousand. The installation of lighting devices on Lada Vesta by an official VAZ representative is carried out only in this way.

The complexity of equipping foglights at a dealer lies in the complexity of the circuit, which was designed by VAZ electronics specialists. The scheme for switching on this lighting in Lada Vesta differs from previous models and is more complex. In Vesta, the fog lights are controlled using a switch located under the steering wheel. This switch does not have a fixed on/off position.

In addition, as mentioned above, Vesta has an auxiliary body electronics unit, to which a signal is primarily sent from the steering column lever. The block transmits a signal to the headlights. Most drivers who purchased a Lada Vesta not in the highest configuration are unlikely to have an additional 60 thousand rubles. for the installation of fog lights.

The way out is to equip the car with headlights yourself and bypass the difficulties by assembling a separate headlight switching circuit. To do this, we use a separate button to turn it on/off.

Lada Vesta. Replacing lamps - part 1

For normal operation of the lighting and light signaling system, use the lamps specified in Appendix 2,

Note. You can replace the lamps yourself using the methods described below. If replacement seems difficult, it is recommended to contact your dealer.

ATTENTION!

Before replacing a lamp, make sure the associated signal light is turned off.

Block lights

To remove the low beam lamp, do the following:

— remove cover 2 (Fig. 11) by turning it counterclockwise;

— disconnect the wire block 7 from the lamp;

— remove the antenna 8 of the spring clamp from the groove;

- remove the lamp;

— Install the new lamp in the reverse order.

To remove the high beam lamp, do the following:

— remove cover 1 by turning it counterclockwise;

— disconnect wire block 6 from the lamp;

— remove the antenna 5 of the spring clamp from the groove;

- remove the lamp;

— Install the new lamp in the reverse order.

To remove the turn signal lamp, do the following:

— turn socket 4 counterclockwise and remove it from the seat assembled with the lamp;

— remove the lamp from the socket by turning it counterclockwise;

— Install the new lamp in the reverse order.

To remove the daytime running light and side light bulbs, do the following:

— turn socket 3 counterclockwise and remove it from the seat assembled with the lamp;

— remove the lamp from the socket;

— Install the new lamp in the reverse order.

Rice. 11. Headlamp

Tail lights

Replacing the turn signal and brake/side light bulbs on the exterior fender light.

To replace the turn signal lamp 4 you must:

— open the trunk trim hatch located in the rear light installation area, providing access to the socket connector 4 of the turn signal lamp;

— turn patron-connector 4 counterclockwise and remove it from the seat assembled with the lamp;

— remove the lamp from the socket by pulling it towards you.

Reinstall the cartridge connector in the reverse order.

To replace the brake/side light bulb 3 you must:

— open the trunk trim flap located in the rear light installation area, providing access to the socket-socket 3 of the brake signal/side light lamp;

— turn the socket-socket 3 counterclockwise and remove it from the seat assembled with the lamp;

— remove the lamp from the socket by turning it counterclockwise.

Reinstall the connector cartridge in reverse order.

Replacing the reverse and side light bulbs on the interior light located on the trunk lid of the car

To replace the reverse light bulb 1 (Fig. 12), you must:

— unlock the two outer holders 1 (Fig. 13) of the trunk trim 2. The trim holder is a structure of a fixed base and a movable fixing “fungus” 3 (Fig. 13). When the “fungus” is raised, the holder is unlocked;

— to unlock the trim holder 3 (Fig. 13), it is necessary, for example, to slightly lift the moving part of both holders using the blade of the ignition switch key 4 (Fig. 13);

Rice. 12. Tail lights

Rice. 13. Replacing the reversing and side light bulbs on the outside lamp

— overcoming the resistance of the holders, bend the trunk lid trim to gain access to the connector cartridge 1 (Fig. 12). To avoid damage to the upholstery, bend back no more than 7-8 cm;

— turn the socket connector 1 (Fig. 12) counterclockwise and remove it from the seat assembled with the lamp;

— remove the lamp from the socket by pulling it towards you.

Reinstall the connector cartridge in reverse order.

To replace the side light bulb 2 (Fig. 12), you must:

— using the same sequence as for replacing the reverse light lamp 1, provide access to the connector socket 2 of the side light lamp;

— turn the socket-socket 2 counterclockwise and remove it from the seat assembled with the lamp;

— remove the lamp from the socket by pulling it towards you.

Reinstall the connector cartridge in reverse order.

To replace the reverse and side light bulbs in the right headlight, a similar sequence is used.

Video on the topic “Lada Vesta. Replacing lamps"

Replacing DRLs of standard Lada Vesta lamps with LEDs.

How to replace the low beam headlight bulb on a Lada Vesta

Lada Vesta. Replacing a burnt out STOP lamp in the rear light

We install PTF ourselves

Let's look at the installation process. From the list of factory items you should purchase: fog lights, a power button, inserts for attaching the lights to the bumper, a 4-pin relay, a 16-amp fuse, a wire, a plastic corrugation (at least 5 m long). First you need to dismantle the bumper and cut through the plugs where the headlights are installed. The cuts are made either with a 76-diameter crown or with a knife. We attach the fog lamp bracket with self-tapping screws. In the lower left part under the steering wheel of the Lada Vesta (near the button that opens the trunk) we install a button for turning on the fog lights. It can also be placed directly on the instrument panel. You must first cut out a receiving hole for the button.

The wires leading to the right headlight should be hidden in a metal box. From the engine compartment to the passenger compartment we lay the wire through a special hole in the pedal assembly. In this case, a simplified scheme similar to the Lada Kalina, Priora, Grant is used.

Power to the relay is supplied from the battery (necessarily through a fuse). The positive contact for controlling the button is supplied from the mounting block. Take the plus coming from the dimensions or the cigarette lighter. The device for closing the circuit can be located both inside the cabin and under the hood. We connect all the elements of the circuit according to this diagram and check the operation of the PTF using the button.

As you can see, a set of fog lights installed independently is much cheaper.

Reasons for replacing a light bulb

Fog lights in a Lada Vesta car are connected to a common network separately from the head light

Therefore, if the fog lights stop working, then you should pay attention to whether the other headlights are working

'); if("undefined"===typeof loaded_blocks_drive){loaded_blocks_drive=[]; function n(){var e=loaded_blocks_drive.shift(); var t=e.adp_id; var r=e.div; var i=document.createElement("script"); i.type=”text/javascript”; i.async=true; i.charset=”utf-8″; i.src=»https://www.drivenetwork.ru/data/»+t+».js?async=1&div=»+r+»&t=»+Math.random(); var s=document.getElementsByTagName("head")||document.getElementsByTagName("body"); s.appendChild(i); var o=setInterval(function(){if(document.getElementById(r).innerHTML&&loaded_blocks_drive.length){n(); clearInterval(o)}},50)} setTimeout(n)}loaded_blocks_drive.push({adp_id:e ,div:t})})(47602)

If the head light works, then first of all you should check the fuse on the PTF. After removing it from the fuse box, check the integrity of the wire inside. If it is intact, then the reason is different, and if a break is found on it, then simply replace the fuse.

The second, no less common cause of headlight malfunction in the Lada Vesta model may be a break in the system itself. You need to look for it either in the wiring located between the bulbs and the relay, or in the relay itself. You can check the break using an ammeter, or see visually if the wire is broken.

https://youtube.com/watch?v=WMcRhlBOK0I

If only one headlight does not light, you should look for the cause directly in it. Most likely, the light bulb has simply burned out and needs to be replaced. A more difficult situation is when, along with the PTF, the head light also does not light up. Then there can be a lot of reasons, starting from the battery power supply and ending with the head wiring.

Another reason why Lada Vesta owners replace fog lights is the quality of their lighting. From the factory, PTF bulbs are coded H-11, which is quite small in conditions of heavy fog or heavy rain. Also, the factory version has white filters, which are not at all effective when driving in bad weather.

As an option, instead of halogen lamps, xenon can be installed in the PTF, but with special curtains so as not to blind oncoming traffic.