3 types of windshield wipers for winter: which ones to choose?

The length of the left wiper (driver's) is 600 mm (60 cm, 24 inches), the length of the right wiper is 410 mm (41 cm, 16 inches). Rear wiper - from 360 mm to 406 mm (36 cm - 40.6 cm, 14 - 16 inches).

REMOVAL AND INSTALLATION (REPLACEMENT)

Clean dirty brushes with a rag moistened with water or a special product. If the brushes are very dirty or covered with ice, they should be removed and cleaned. To do this, move the lever with the brush away from the windshield.

Press the brush locking tab.

. and move the brush down from the hook of the lever so that the brush lock comes out of the hook.

Remove the brush from the lever.

If you need to replace the brush retainer.

. move it from the brush axis and remove it.

Similarly, remove the other brush, as well as the rear one, if present.

Install the brushes in the reverse order until they click.

CHOICE OF “WIDERS”

Car wipers are such a simple and uncomplicated thing that the date is somewhat surprising in our time of high technology. And really, how much easier is it? Previously, they were generally driven manually from the driver’s cabin, then an electric motor with a trapezoid appeared, but the essence did not change.

Well, really, how much can you scrape on glass with mechanical devices? Is it really impossible to come up with something new? Attempts have been and are being made, but things are still not going well. Ubiquitous dirt, which has recently acquired another component - sticky and sticky oil fractions that are difficult to clean, the sheer amount of dirt on the roads, which is constantly increasing (environmental pollution, nothing can be done). Seasonal phenomena and rising average vehicle speeds continue to force automakers to use mechanical cleaning methods to avoid blinding the driver. Why haven’t you tried it! Vibration of glass in a certain, ultra-high range, special compositions for processing that prevent wetting, but. for now everything remains largely the same. It is possible that chemists or physicists will eventually come up with something, but for now engineers have come from the other end: rain sensors have appeared, algorithms for the operation of the system as a whole have been improved, and, of course, developers are constantly trying to improve the final link - the windshield wiper blades themselves.

So, according to their design, wipers are divided into four classes: frame, hybrid, frameless and winter. In principle, winter brushes can be called any brushes covered with thin rubber on top, which, in the opinion of designers, prevents freezing.

The cheapest and most versatile at the moment are ordinary frame brushes. They are over 60 years old, but, as we have already noticed, in some cases, especially in this one, the timeless classics are in no hurry to retire and show very good results. By the way, despite the emergence of new designs, the main fleet of cars is still equipped with frame windshield wipers. What are the benefits?

There are quite a lot of them: 1. Affordable price. Since brushes of this type have been produced for a very long time, production facilities are working at full capacity, all the know-how has long been introduced, and mass production is fully established, including in car exporting countries.

2. Versatility. The design itself ensures an acceptable fit of the entire surface of the blade to the windshield of almost any configuration, so you only need to focus on the required length, since branded products always come with a set of adapters that allows you to install the frame structure on almost any car.

3. Currently, such brushes are equipped with aerodynamic spoilers, which helps them maintain contact with the working surface even at high speeds.

Quick comparison

I offer brief recommendations for wipers. Choose what is more important to you and buy. A detailed description, installation video and price comparison are below.

Frameless windshield wipers for Kalina

An excellent option is the Bosch Aerotwin Retrofit AR 601 S kit (article number 3397118907). This is a pair of brushes of the “native” size and fastening. Cleans well in any weather, quiet, durable. They are produced in Belgium. Find out more about Bosch Aerotwin.

Champion piece brushes 600 mm (item ER60/B01) and 400 mm (item ER40/B01). They are easy to install and clean glass well. Read more about Champion Izivision.

SWF piece brushes : 600 mm (article 119860) and 400 mm (article 119840). Asymmetrical spoiler, excellent cleaning, easy to install. Read more about SVF windshield wipers.

Also pay attention to the Kamoka (article 27E09) - frameless Polish wipers. Read more about Kamoke.

How to install brushes on Kalina

Watch the video on how to install Bosch wipers correctly:

Before choosing, it will be useful to become familiar with the types of wipers on the market that apply to the Lada Kalina in order to understand which ones are better. For this model, there are only two categories of these products on sale today:

• frame;
• with no frame.

Each type has its own advantages, but both of them are not without disadvantages.

Frameless options have great durability. The materials used for their production are high-quality rubber and durable plastic. Time on this type of product does not have a strong effect and does not cause significant wear. The cleaners are characterized by soft operation and no squeaking. They are also not afraid of temperature changes.

Now about the disadvantages. There is only one – high cost.

The frame elements are made of metal with the use of plastic parts in the design. These components are integrated inside a metal frame. Brushes have a low cost and are sold in almost any retail chain.

The disadvantages of this type of product are very varied. Production does not involve the use of high-quality materials, so the wear and tear of such products is observed with enviable intensity. Two years of moderate use render the brushes completely unusable, after which the inevitable moment of replacement comes. Creak is an eternal companion to the work of frame products. It is also possible that the working component may break, which makes cleaning much more difficult.

Why do you need glass cleaner?

One of the elements of comprehensive vehicle safety is the front and rear wipers. Its differences are minimal for different generations of Lada Kalina models. The device includes not only the usual brushes that clean organic and inorganic contaminants. A mandatory addition will be an electric drive, which is protected by a special fuse.

Without these components, the mechanism will not be able to perform its activities efficiently, which means its performance will be reduced. When the inserts burn out, the entire system unit will stop.

The correct choice directly affects the level of efficiency of the Lada Kalina windshield wiper. A good device, made to all standards from high-quality materials, will work without any extraneous squeaks. Also, the working elastic band will not break on new models.

Purifier size

This is an important criterion that has a direct impact on the selection process. The area of ​​the glass surface to be cleaned depends on the size of the product's wipers. The rear wiper for a hatchback may differ in size from the front wipers, which must be of sufficient size to maintain the required cleaning efficiency.

In practice, it has been observed that the optimal overall dimension of the windshield wipers for the front glass is 24 inches. By the way, for the “passenger” section you can safely use the 16-inch version of the product.

For the stern glass, you can choose an accessory according to the personal preferences of the owner. Many owners of the Lada Kalina hatchback version testify that the most rational size of wipers is 24 inches. With such a “unit”, cleaning the glass surface will be quite effective, since the treatment area in this case is maximum.

When purchasing wipers, you will need the attention and advice of the seller to ensure that the size of the windshield wiper blades indicated on the packaging corresponds to the actual parameters of the product. This is due to a cunning maneuver by accessory manufacturers to tend to round off digital data. This aspect does not carry a global burden, however, having reliable information will not prevent the owner from gaining confidence in the ideal applicability of the cleaners to his LADA Kalina car.

Fuel tank volume Lada Granta

Rails for Granta sedan

What are the best spark plugs for Lada Granta 8 valve

What other points to consider?

When choosing accessories for LADA Kalina, it would be useful to take into account the shape of the glass, and this applies not only to the front part, but also to the rear, as well as the size of the windshield wiper blades. If the front glass is curved outward, then the best option for it would be to purchase and install cheap brushes of a frame structure. This is caused by the inability of the frameless option to effectively clean glass of this shape. During operation, such products will leave marks on the surface in the form of stripes located on the outer edges of the cleaning zone.

Maintenance and selection of wipers for Lada Kalina

Wipers protect from dirt and rain

Windshield wipers are an important element of any car. They provide the necessary visibility from the cab during heavy rain or snowfall. Driving in adverse weather conditions with poorly functioning windshield wipers creates a potentially dangerous driving situation not only for the owner, but also for pedestrians and vehicles around him. For this reason, it is necessary to constantly monitor the performance of all parts of your personal vehicle and, if necessary, replace the windshield wiper blades.

The operating principle of the wiper mechanism on the Lada Kalina is simple. If certain difficulties arise in the operation of the device, they can be easily eliminated by any car enthusiast. The main thing is to understand a little about the design features of the windshield wiper system.

When the wipers on Kalina do not work well, first of all you need to check the mounting block and make sure that the required fuse is intact. This is the most common cause of the problem, which can be fixed even by an inexperienced driver. To carry out the replacement, you need to find and remove the fuse box cover, which is located under the steering wheel on the left side. On the back of the cover there is a detailed block diagram where you need to find the required fuse and then replace it.

Problems with the wipers

Therefore, it is recommended to constantly monitor the operation of the wipers and promptly correct various problems. The principle of operation of wipers is simple, and most problems can be resolved independently. The main question here is to know a little about the operating principle of this unit.

In the case when the wipers on the Lada Kalina start to work poorly, you first need to check the mounting block, as well as the integrity of the fuse. As noted, this reason is the most common. Even a beginner can fix it. To replace the fuse, you must remove the cover from the fuse box. It is located under the steering wheel on the left. There is a diagram on this cover that will help you figure out where each fuse is located. It must be found, checked and replaced if necessary.

Intermittent operation

In this case, attention should be paid to the relay.

Appearance of the wiper relay

Wiper relay number K6.

Fuse box diagram

Also, if necessary, replace the relay. It is located next to the fuses in the mounting block. If the relay is working properly, then you need to check the drive. All contacts are inspected for oxidation. If necessary, they are replaced with new ones.

If this does not help, then you will need to check the entire system with a tester. In this case, make sure that voltage is supplied to the terminals.

Causes of problems and methods for eliminating them

Wiper control mechanism

In case of intermittent operation of the windshield wipers, you need to pay attention to the functionality of the relay and, if necessary, replace it. The relay is located inside the mounting block next to the fuses.

If the wipers still do not work, you will need to check the electric wiper drive. First of all, you need to inspect the ground terminal, which is located in the Kalina body structure right next to the rack. It is necessary to dismantle it and thoroughly clean the place where it is attached. After that, install it back and check the operation of the wipers.

If there is no result, you will have to disassemble the electric drive system and check its functionality using a tester. It is necessary to make sure that the electrical wiring is intact and power is supplied to the windshield wipers. The presence of power signals that it is necessary to replace the electric motor responsible for the operation of the wipers.

To do this, you will need to disconnect the terminals from the battery and remove the protective caps from the leads. Unscrew the screws that secure the leashes and set them aside. Then unscrew the bolts that secure the grille insert that is located under the windshield frame. After this, you need to carefully remove the electric motor from the socket by disconnecting the wires. Place a new electric motor in the vacated slot and reassemble the device in reverse order.

If there is no power to the electric drive, you will need to disassemble the steering column and change the wiper controller. To do this, you need to disconnect the terminals on the battery, and then remove the plastic trim on the steering control. Remove the switch block by pressing on the fixing fasteners on both sides, and remove the switch itself. Install the new switch and reassemble the steering trim in reverse order.

The electric drive functions, but the windshield wipers do not work. In this case, you will need to inspect the trapezoid and wiper gearbox. Remove the windshield wipers and unscrew the grille insert under the windshield frame.

Now you need to make sure that the gearbox really works - its axis must rotate. If it works, but the trapezoid does not move, it is necessary to inspect the splined connection of the gearbox to the trapezoid. If the device is not seriously damaged, the nut must be tightened. But if it is worn out, you will need to replace it with a new one.

By car

It's only minus five outside. But even at this temperature, both heated wipers were unable to melt the snow that had dusted the windshield, at least in close proximity to the adjacent rubber bands. What happens if the brushes freeze to the glass after a frosty night?

We checked this too. It started snowing in the evening and froze at night. The next morning, both heated wipers were frozen to the windshield. And although the air temperature dropped only three to four degrees below zero, amperes and volts could not save the wipers from captivity. The heated wipers were partially rehabilitated during the day, when wet, sticky snow fell from the sky again: the usual transformation into a “snow woman” type windshield wiper did not happen.

Heating - a view from the inside. In the Energomash product (1), the metal plate is placed in a plastic insulator. Burner (2) looks more civilized.

Heating - a view from the inside. In the Energomash product (1), the metal plate is placed in a plastic insulator. Burner (2) looks more civilized.

Selecting wiper blades

Wipers come in different types depending on their purpose. They are distinguished by their size, degree of frost resistance and increased operating cycle. When choosing windshield wipers, you need to consider the advantages and disadvantages of each option.

Frame brushes are usually made of metal, but they have a large number of plastic inserts. With frequent use, such brushes quickly waste their resources and often become loose. These wipers deteriorate quickly when exposed to cold temperatures.

Frameless brushes are made from rubber and plastic and have an arched shape. The main advantage of such wipers is the absence of noise and increased resistance to frost. Frameless wipers serve for a long time. In addition, these windshield wipers can be easily updated, you just need to choose the right blade size.

Standard brush sizes for Lada Kalina:

• Driver's side wiper - 600 mm / 24 inches;
• Passenger side wiper - 400 mm / 16 inches.

Standard wiper brush length

When purchasing, you should pay attention to the fact that some manufacturers round the size in cm or inches.

Dimensions

When purchasing, you need to consider the overall dimensions of the wipers. They must match:

Instructions for installing wipers on Kalina

First of all, you need to remove the blades and unfasten the lock on one end of the wiper. After this, you will need to remove the rubber bands that are attached to the frame. But this must be done carefully, as they can be tightly pinched by the plastic.

Now you should compare the new rubber bands with the old ones and, if necessary, trim them. It is not recommended to use a knife or pliers for this; it is best to take scissors.

New rubber bands must be placed tightly on the windshield wipers. This can be done in 2 ways: either straighten the terminals with a screwdriver, or try to insert the rubber bands yourself. With the first option, there is a risk of damage to the terminals, and with the second, you can carry it for a long time. Everyone decides for themselves what is more convenient for them. But if you act carefully and take your time, you can try changing the rubber bands using the first method, saving time and effort.

After placing the rubber bands, you need to fix the fastening lock and lightly press the holders on the frame with pliers. You should act carefully as there is a risk of breaking the fragile plastic.

Replacing wiper blades (+ video)

The blades are removed and the lock on the end of the windshield wiper is unfastened. Next, the rubber bands that are mounted on the frame are removed. Work must be done carefully. Next, new brushes are installed. If necessary, they are trimmed. You need to use scissors for this. The new rubber bands are tightly attached to the windshield wiper. Here you may need to straighten the fasteners or push the brushes under them. In the first option, you can accidentally damage the terminals, and in the second, you can fiddle with the work for a long time. Here everyone should choose the most convenient method for themselves.

As you can see, replacing and repairing wipers is a fairly simple job. This does not require certain skills and knowledge from the driver. The main thing is to understand the design of this system and know where to look for a fault. You also need to be quite careful when carrying out work. In winter, you need to make sure that the brushes are not frozen and there is no ice on them, as this can lead to damage to the glass.

What is the size of windshield wiper blades for Lada Kalina

Let's consider an example when a Lada Kalina has larger windshield wiper blades installed than indicated in the vehicle's technical manual. In the described case, the downforce will be reduced, as a result of which the quality of glass cleaning will significantly decrease. And if their size significantly exceeds that set by the factory, then the brushes may even come out onto the glass seal when moving, which will soon lead to its wear.

If smaller brushes are installed, then due to the small cleaning area the overall glass cleaning effect will be reduced. At the same time, it is possible that a spot of water and dirt may form in the center of the windshield, which impairs visibility through the glass while driving.

Additionally, incorrectly sized windshield wipers can cause the entire windshield wiper system to malfunction. For this reason, it is necessary to constantly monitor the performance of all parts of your personal vehicle and, if necessary, replace the windshield wiper blades.

Replacement

The process of replacing old windshield wiper blades with new ones does not cause serious problems. It is only important to carry out all actions carefully, not to break the plastic fastener included in the kit. The replacement process includes the following steps:

• lift the wiper up, it is fixed in this position - perpendicular to the windshield;

• Next, you need to take the brush body in your hand and squeeze it, then move it down - slight swaying will simplify the procedure;

• then the brush is simply removed from the lever.

The installation process is performed in reverse. Many brush models are supplied with special adapters. They must be used carefully. Plastic is usually fragile. If it is damaged, it will be impossible to install the brush in place. Which will make it impossible to use it. When choosing a brush, it is important to focus on the brand. To date, Bosch, Champion and Denso have proven themselves to be good.

It is important to replace brushes in a timely manner, since road safety directly depends on this. Otherwise, precipitation falling on the windshield simply will not be removed in time.

How windshield wiper blades work on Lada Kalina

The mechanism of the windshield wiper and the principle of its operation are simple. If any malfunctions occur in the device, they can be eliminated without the intervention of specialists; any car enthusiast can easily understand this system. The most important thing is to understand at least a little how the wiper mechanism on Kalina works.

If a malfunction occurs with the windshield wiper system, from the very beginning it is necessary to check the integrity of the fuse responsible for this system.

In the vast majority of malfunction cases, it is the failure of the fuse that causes problems with the windshield wiper. Even the most inexperienced driver can fix this problem.

To replace a faulty fuse, you need to find and remove the fuse box cover in the car interior, on the left under the steering wheel. On the inside of the block cover is a block diagram detailing the purpose of each fuse. We find the fuse we need and replace it with a new one with the same rating.

It happens that the windshield wiper works with some interruptions. In this case, you should check the relay and, if it is faulty, replace it with a functional one. This relay is located in the fuse mounting block.

If the problem is not solved, check the electrical wire of the windshield wiper for integrity. From the very beginning, we inspect the terminal connected to ground. It is located in the back of Kalina near the counter. We unscrew it, clean the joint and the terminal itself from corrosion, lubricate it with thick oil and put everything in its place. After this, you can check the wipers for functionality.

What size to choose for Lada Granta, Kalina 2 wipers

27 May 2015 LadaOnline 129 032 6

To ensure high-quality cleaning of the windshield, it is recommended to replace the wipers with new ones every season, however, in practice, drivers do this much less often. But sooner or later everyone is faced with one question: “what is the permissible size of brushes on the Lada Granta/Lada Kalina 2.”

Why did we combine these two cars? The fact is that the second generation Lada Kalina 2 is produced only in hatchback and station wagon body styles, and the Lada Granta is considered a sedan in this line. That is why Lada Kalina 2 and Lada Granta have a lot in common, including the same windshield wiper blades (1118-5205072 and 1118-5205070), windshields (2190-5206012), etc.

The operating manual indicates the standard size of windshield wiper blades for Lada Granta and Kalina 2:

• driver's (left) - 60 cm.
• passenger - 41 cm.

We decided to find out what is the maximum possible length of the wipers of the Lada Granta/Kalina 2. It turns out:

• If you install a 61 cm long brush instead of the standard one, it will touch the body, creating a knock. Maximum - 60 cm.
• But the passenger side allows you to install a larger brush, the maximum possible length is 45 cm.

maximum size of windshield wiper blades for Lada Granta/Kalina 2maximum size of windshield wiper blades for Lada Granta/Kalina 2maximum size of windshield wiper blades for Lada Granta/Kalina 2

Thus, the maximum size of the wiper blades of these two cars is 600x450 mm. With this length, both blades on top of the windshield will be at the same level. Unlike the standard one, the longer passenger brush will completely clean the glass in the upper part, without touching the body.

Let us remind you that these Lada cars have common not only windshield wipers, but also “diseases”, for example, both cars have a squeaking clutch pedal.

Keywords: windshield wipers Lada Kalina 2 | glass Lada Kalina 2 | windshield wipers for Lada Granta | Lada Granta glass | Lada Granta accessories | Lada Kalina 2 accessories

what kind of
wipers are installed
on viburnum How to change wipers

on viburnum. When you put them back, you will need this information.
If you put them in the wrong position, they can hit the bottom of the pad during operation, scratching it and damaging the brushes. Well, there’s another problem that occurs on Kalina, the brush on the driver’s side hits the edge of the driver’s door. Someone also sets it to 40cm, but in this case it will be necessary to increase the limit of the wiper stroke. Buy frame fin whales for 250 rubles (there are just 2 brushes in the box, 60 and 40 cm) for Kalina , and don’t load your head with crap like diagrams of the torsion and twist of the “windshield wipers” during And what leashes should be installed on the VAZ? That’s the problem, and not only with the VAZ. Alex.ru. boils down to replacing the rear wiper with a wiper from Kalina
1. Someone tried to rivet the wiper mounts, installed different springs. I simply bent the rear wiper handle (the steel plate on which the windshield wiper blade is held) more strongly. As a result, I installed a relay with an adjustable wiper pause on Kalina - it’s a comfortable thing, you can set the clearance between the strokes of the brushes and first Any
wipers (up to 400 rubles per set) scrape at the factory. They install some unbearably cheap brushes that they The mechanism of operation of the wipers on a Lada Kalina
is quite simple.
Even if the windshield wiper blade breaks down, every car owner will be able to fix the problem. True reviews about various brands of wipers, windshield wiper blades. Lada Kalina has excellent blades (I’ve been installing these for the summer for the 3rd year now) they are enough for about a season, but in winter they freeze up like an ordinary frame from any manufacturer lkforum.ru/showthread. php I would like to install regular blades, because the standard ones are unsafe for me and those around me - I don’t work at all, the snow sticks in general, it’s terrible, but by the way, if you want to save money, then just remove the wipers , rinse, dry and drop some engine oil into the hinges with a pipette, only the wipers . From a new perspective I have special requirements for windshield wipers.4. We place the leash vertically with the hook up and with light blows on the hook we drive the lever into the base to the required 2-2.5 cm. Thanks to the rust, it is very comfortable to evaluate, on I went to a car store, bought brushes for viburnum
(as it was written on the price tag) for 370 rubles. Goes here and there on a janitor's leash and that's it. It is not correct. (for sure).

FakeHeader

Comments 40

Hello, is it possible to go out to the car in the morning and immediately turn it on or do you have to wait until the car heats up?

I turned it on immediately, a couple of times at -20 and nothing was wrong.

Hello! Please tell me, did you accidentally measure the heating current? Doesn't it need a separate fuse?

I can’t say, I didn’t measure it.

Time has passed, how is the heating going?

everything is fine, but in heavy snowfall and if it’s more than -10 it can’t cope.

Well, it will work anyway... I still couldn’t find such stripes!

yes, it’s better than nothing))) you need to check the sites, I think there are some with delivery.

what did you buy, what are these stripes, how can I ask the store what I need?

Heated windshield in wiper area

Is there no diagram of how to connect it? And even more interesting is which wires I threw on.

There is no diagram and I don’t know how to draw it))) I described everything by wire here www.drive2.ru/cars/lada/k…ragon063/journal/2238073/