The practical model Lada Largus has been an enviable success among car enthusiasts since its appearance. This car is a joint brainchild of Renault-Nissan and AvtoVAZ. The station wagon is distinguished by excellent build quality, but the domestic model cannot show off its exterior. Here the manufacturers were modest, giving priority to rigor and practicality. Understanding this state of affairs, owners strive to improve the appearance of their station wagons by resorting to such things as tuning.
In our material we tried to collect the most successful options for modernizing the Lada Largus.
Ignition switch illumination
Illumination of the ignition switch is a rather convenient “feature” when the car is frequently used at night in poorly or unlit places.
To modify the ignition switch and install the backlight, a minimum of parts are required, and all the work, including the connection, takes about an hour.
After some simple manipulations with the ignition switch, you will not experience any difficulties when using the car in the dark.
To work you need:
- LED of small diameter, for example, 2.5–3 mm;
- resistance 1–1.5 kOhm;
- the wire.
To install the backlight, you need to remove the lock cover. It is removed together with the immobilizer antenna, and then remove the top cover of the casing.
At the second stage, the LED is installed inside the lock housing. To ensure uniform illumination, small slits can be made in the housing, after which the casing is assembled and installed in place. The wires coming from the LED are pulled to the CEBCS unit and connected to the white connector. To connect the wires, you can use gray or white wires - this is a “minus”. For “plus”, either of the two red wires is used.
Connecting to the CEBKS unit allows you to get the lighting to work similar to turning on the interior lamp - it lights up when the Lada Largus is disarmed, when the doors are opened, and goes out either after the doors are closed or after the ignition is turned on.
CAR SERVICE
PashkaNaLargus: |
I just didn’t like it, it’s a bit low. |
Agree! A little inconvenient. .(
PashkaNaLargus: |
In place of the air ducts it would be. |
That would be just right! But it is technically impossible to do this!
ps I liked the 2DIN radios with a motorized screen! But unfortunately, “comrades” from the Middle Kingdom do not make these for LL on Android. Or at least I didn’t see them. There are ordinary radio tape recorders, but there are no such ones.
Source
Chip tuning Largus Cross - small adjustments for grandiose changes
Despite its complex design and a huge number of new products in the field of automotive electronics, everyone can perform chip tuning of the Largus engine with their own hands. All you need is a little patience, computer hardware and licensed software. The latter includes:
- Combiloader loader, updated to the latest version;
- Firmware purchased strictly from the official website. For chip tuning the Lada Largus Cross, the Bosch 7.9.7 utility or the latest version January 7.2 is perfect;
- editor for configuring and calibrating firmware;
Programs and equipment for chip tuning Lada Largus
As for the equipment, for effective work on flashing the engine ECU, you need a K-Line adapter and a laptop exclusively with Windows XP. Other software will not find the firmware, which is why you will not be able to even start chip tuning.
First in line are the loader and editor. After their successful installation, we begin to work with the firmware. To do this, install it on your computer, indicating the final location address in the previously installed bootloader. When the latter finds the firmware, you need to configure it. In the “Settings” window you will find a lot of graphs that will help you choose the optimal characteristics for your station wagon.
Lada Largus ECU firmware
Having calibrated the firmware to your liking, turn on the ignition and proceed to the most important stage of chip tuning - installing the firmware on the engine ECU. To do this, click on the “Run” window and wait for the utility installation to complete.
Once the download line reaches the end and you see the “Download Complete” window, turn the ignition back on and close the installer. Next, close the bootloader and editor and turn off the ignition. After this, disconnect the adapter from the laptop and ECU.
At the last stage, you can check the operation of your car. Provided that the characteristics are properly calibrated and chip tuning is performed correctly, you will immediately notice an improvement in car dynamics, a reduction in fuel consumption by about 20%! and more stable operation of the engine and transmission.
We recommend: How to recognize a damaged car?
Let's sum it up
Lada Largus Cross is a model that allows its owners to perform a wide variety of tuning and introduce all innovations to an unlimited extent. At the same time, you can do almost everything with your own hands. Here the main factor may be the financial component, which often determines in which direction tuning should be developed in a particular case. If this aspect does not concern the owner who is prone to transformation, then desires and preferences come to the fore.
The result of tuning the Lada Largus Cross will be not only a satisfied owner, but also a significantly transformed car; all innovations are the path to individuality, which is so rare in our time.
Say a word about Largus Cross
The Cross version is the case where changes can be kept to a minimum. If I had a choice between Largus and Largus Cross, I would without a doubt take the second one. And I would recommend this to everyone.
The car initially, if taken in a good configuration, minimizes the need for tuning. Everything I said before applies here.
But in practice, only some of the improvements are really useful in this case. I explain my position. The Cross version initially offers:
- original body kits;
- wheels with a diameter of up to 16 inches with beautiful designs;
- roof rails, regardless of configuration;
- rear parking sensors, regardless of configuration;
- improved suspension struts (with them it’s not so scary to drive off-road);
- modified seats with good lateral support and increased comfort compared to the regular Largus;
- beautiful door cards and panels;
- interesting dashboard along with the dashboard;
- leather steering wheel;
- The standard audio system already has 6 speakers (but I would still install multimedia).
Yes, most car owners don’t need more. The main thing is to initially buy a car with a rich configuration. Then tuning your Largus Cross comes down to a minimum set of modifications.
Don’t forget that AvtoVAZ offers several features for Cross from the factory. Namely:
- tourist roof box for 10 thousand rubles (excellent quality and appearance);
- off-road tires (approximately 3-6 thousand rubles);
- standard tinting (complies with GOST, does not raise questions from the traffic police, costs about 10 thousand rubles).
By paying about 30 thousand extra, you get a car in full combat readiness.
This is not an exemplary SUV, but an all-terrain station wagon. But considering the price of the car, its technical characteristics and level of comfort, it completely justifies itself. What do you think, is it worth doing tuning in the case of the Lada Largus and what changes are you ready for?
https://youtube.com/watch?v=LPHwXlcTy7c
(6 ratings, average: 4.67 out of 5)
Subscribe to updates and receive articles by email!
We guarantee: no spam, only new articles once a week!
Lada Largus is a family car, which is a joint development of our automobile industry and the Renault-Nissan alliance. Regardless of the type of body (station wagon, minivan or van), this model is assembled of very high quality, but rather “raw”. Apart from reliability, which is already loved by many, Largus cannot be noted for literally anything. Given this state of affairs, the desire to tune their car among owners of this model is very common. Having collected the most successful solutions for modernizing Largus, our resource presents today’s material to its readers.
Is it worth tuning Lada Largus for a sports car?
Lada Largus tires which come from the factory
The Lada Largus is a family car, a conservative and stable car, the expression “angry and cheap” fits it.
This is the first “foreign” model to roll off the Tolyatti assembly line in June 2011, after the cars were produced under license from Fiat.
The newly created VAZ brand has a foreign analogue - Dacia Logan MCV.
Lada Largus is produced in three versions: a passenger station wagon, a station wagon with increased capacity and a cargo van. Moreover, passenger versions can have either five or seven seats.
Therefore, although the line of VAZ models is very often liked to be modified and subjected to aggressive tuning, it makes no sense to turn a new excellent “workhorse” for family trips, traveling with a large group and transporting cargo into a sports model using tuning.
And if you simply install body kit parts and sills on the car, they will indeed provide the car with a sporty look, but can slightly reduce the cross-country ability and spoil the ground clearance. It's up to the car owner to decide.
Largus interior tuning
Interior tuning here has the goal of the event, which comes down to improving the interior not only from an aesthetic, but also from a functional perspective. The following areas of activity are available to each owner:
- replacing covers with more modern models or installing new seats instead of standard seats;
- covering interior panels with new materials (leather, Alcantara, etc.);
- replacing the steering wheel with a sports-style analogue is also a kind of tuning of the interior;
- installation of more aesthetic regulators, switches, overlays, lighting sources, including additional ones (for example, for legs);
- armrest installation;
- replacing door handles with analogues and installing backlighting;
- soundproofing of the cabin space.
Such interior tuning should be done carefully and slowly, which will allow, upon completion of all manipulations, to acquire a stylish and beautiful interior, also made with high quality.
More about multimedia
This is another stage included in interior tuning. It involves replacing standard multimedia elements with more advanced and functional audio components. All work can be done with your own hands.
Transformations of this nature are subject to:
- head units;
- speakers (both replacement and installation of additional speakers);
- connecting and installing a subwoofer;
- TV installation.
Here, when performing tuning, it is possible to interfere with the design of some standard elements of the body and interior, which will have to be taken into account in advance and prepared for. We continue to study all the innovations for the popular Largus model.
Lada Largus (interior tuning)
Describing changes to improve the car with your own hands, we will first consider working with the interior. We’ll start tuning the interior of the Lada Largus by installing such an irreplaceable element as armrests. By the way, when tuning a VAZ 2109 you can also install armrests, they will look very cool.
The armrest is an indispensable element of the cabin, which allows you to give your arms a rest during a long journey. At the same time, some versions of this element still act as a small box when open. The armrest can be purchased assembled and then installed in the interior of your car.
The most interesting way to improve the interior is to organize the illumination of the handle. This improvement can be called very necessary, because at night, if a person is in your car for the first time, it will be difficult for him to find the door handle. This leads not only to increased discomfort, but also to damage to the handle itself in some cases.
Photos of the Lada Largus interior tuning can delight many car enthusiasts. To successfully tune the interior of the Lada Largus, we will need the following necessary elements:
- microswitches;
- 4 LEDs;
- special connectors and adapters;
- 4 resistors with a resistance of 510 Ohms.
Tuning work for the Lada Largus interior
To begin work, you need to remove the casing. To do this, just unscrew several screws hidden under the plastic tabs and remove the clips. After this we disassemble the handle. We attach an LED to its moving part, for which several holes are made at a certain angle using a small drill. Next, we connect the wires to the LEDs and push them through the holes formed.
Do-it-yourself tuning of the Lada Largus, which concerns the installation of the handle illumination, is carried out in several stages, and there is no need to rush when carrying out the work, since a mistake during such work can lead to the loss of the handle itself.
After installing the LEDs in their places, we assemble the handle and connect the connectors. We pass a wire with positive polarity through a resistor (this produces a current of 20 mA at the output). To increase the reliability of fastening connections, we use sealant. Next we connect the microswitch.
The most important step is connecting the microswitch. To ensure its stable operation, we glue it next to the lock rod, or use self-tapping screws. Next, take the stranded wire and attach it to one end of the microswitch. We fasten the free end of the wire to the lock rod using zip ties. Wrap the free wire with electrical tape.
The operation of this switch is as follows: when the lock is closed, the wire bends slightly, which causes the switch to turn off. When the lock is closed, the backlight will go out and only work when the side lights or headlights are on.
Tuning and modification of the Lada Largus may also involve changing the engine, clutch, suspension, appearance, or installing alloy wheels. At the same time, we note that changing the interior increases the comfort of driving the car. Among all the possible modifications to the interior, we note the following:
- installation of new door panels made of higher quality materials;
- installation or modification of the instrument panel;
- installation of a new instrument panel;
- replacing seats with versions with lateral and other supports;
- carrying out sound insulation and using vibration-absorbing material;
- installation of various lighting.
When carrying out work, it is worth remembering that without creativity, patience and perseverance it is very difficult to create a truly memorable car.
Here's how to make glowing wheels on a Lada Largus:
And finally, notes on how older VAZs can be modified:
, , , , Tuning VAZ 2108, , Tuning VAZ 21099, Tuning VAZ 2110, , , , , , , ,
Aesthetic tuning Lada Largus
Tuning can also come down to “simple aesthetics”, which does not particularly affect the performance of the car, but changes the appearance of its interior, making the interior comfortable, improves the exterior of the car, turning the car into “special”.
In this case, the desire to “pump up” the car is just a desire to stand out, be atypical and show individuality.
Aesthetic tuning of Lada Largus, aimed at creating an individual style, provides comfort and influences perception. It may consist of:
- tuning the interior of a Lada Largus car
- changes in the appearance of the car
- installation of audio systems
It is worth noting that the Lada Largus first underwent an “official” modification at the manufacturer in 2013, the car was given alloy wheels, and changes took place in the interior.
The easiest and most affordable way to change the aesthetic characteristics of the Lada Largus is to replace the wheels, equip the car with LED optics, redo the interior and install original bumpers.
It is possible to cover the fog lights in body color, as well as cover the bumper
The aesthetics of the appearance and some of the aerodynamic characteristics of the model will change when replacing the radiator grille, after inserting a new front bumper, installing thresholds, organizing covers on the mirrors and taillights, installing a spoiler and diffuser.
Improvement of the Lada Largus interior may include:
in replacing door panels with similar, but better quality ones; in the modification or installation of a new instrument panel; in replacing or modifying the instrument panel; in improving sound insulation performance; in stopping the additional illumination.
Automatic door locking when a certain speed is reached
It is worth noting that this function is available in many additionally installed alarms, however, Lada Largus owners can activate it themselves, using only the standard car system.
To activate the automatic door locking function, minimal intervention in the standard wiring of the car is required, as well as the presence of a special adapter for connecting the UCH (central electronic switching unit in the cabin) to the computer and special software.
Automatic door locking while driving is very convenient
So, at the first stage, you need to send a signal from the speed sensor to the UCH. To do this, connect a wire from pin 22 of the left connector of the instrument cluster to pin 6 of the brown insert on the black UCH connector. Using this wire, when a +12V control signal is applied to it, when the speed determined in the next step is reached, the doors will be locked.
Now it is necessary to determine the speed threshold, upon reaching which the locking will occur.
To do this, connect a computer or laptop using an adapter to the diagnostic connector and in the running program (for example, DDT2000), the door locking function is enabled, and the speed threshold is set.
The feature is now enabled, but not yet activated.
To activate the function in Lada Largus, you need to press the lock button located on the instrument panel and wait for a sound notification (about 5 seconds), which indicates successful activation. To turn off the automatic locking of the locks, you must perform this operation again by pressing, on the contrary, the unlock button.
About other modernization methods
In addition to the engine and body, the Lada Largus also has a sufficient number of components to which the owner can “offer” improvements.
Depending only on his own needs and preferences, the owner of a Russian station wagon can perform the following transformations:
- in the cabin, changing the appearance of panels and interior components;
- in a multimedia complex by installing more powerful speaker systems or a head unit;
- in the suspension due to the use of reinforced elements.
Installation of wheels with a larger radius
Largus comes standard with 15R wheels. Many motorists choose the 16 or 17 radius option instead of the one proposed by the factory. Additionally, this makes the car's exterior more attractive. However, this option also has a significant drawback, namely the unstable position of the car when driving, as well as malfunctions in the ABS system and some related sensors.
Installation of spacers
The most budget option (and popular) is to install special spacers, which are sold at any auto parts store. The only thing that is required from the car owner is the removal of the suspension struts. The parts themselves are unified and suitable for many VAZ cars. Spacers are installed between the rack and the body bowls (as an option - between the beam and the rack).
Replacing strut parts
One of the best methods for increasing ground clearance is to install stiffer springs and longer shock absorbers. As a rule, such racks are approximately 20 mm longer than standard devices. In combination with reinforced springs, they are able to significantly increase ground clearance, and the car does not sag all the way when transporting the maximum permissible weight of cargo. The only drawback is the higher price of such kits.
Improving the suspension
This direction of modernization can also improve the driving performance of the car. Here, options for action can relate to a variety of goals. Here are some of them:
- the use of reinforced chassis components in order to increase their service life;
- increased ground clearance;
- decreased clearance;
- installation of parts with improved characteristics (shock absorbers, stabilizer, etc.).
This type of modernization is also quite expensive, so this factor should be taken into account before the implementation of the event begins.
Malfunctions and ways to eliminate them
During its operation, the suspension can cause not only all sorts of sounds in the form of knocks and squeaks, but also direct problems with the steering. If this part behaves suspiciously, it should be immediately fully diagnosed.
Noise and knocking while driving
The main reasons for the suspension failure of the Lada Largus are related to uneven roads. For example, a knocking sound in the front suspension of a Lada Largus begins after the car falls into a hole or hits a bump.
In addition, the inexperience of the car owner is not the last circumstance that leads to repair of the chassis. Having noticed a pothole belatedly, the brake pedal is pressed, which only increases the load several times and aggravates the situation.
The problem may be faulty shock absorbers, worn ball joints, loose fastening bolts, or lack of lubrication. If worn parts need to be replaced, this should be done immediately. When a malfunction of the suspension is associated with the fixing force or lack of lubricant, tightening them and appropriate lubrication will correct the situation.
If there is noise or knocking in the rear suspension, in addition to rubber seals and torque rods, attention should be paid to the condition of the exhaust pipe. A detailed analysis of the entire mechanism allows you to accurately determine the cause of the breakdown and eliminate it in a timely manner.
Departure of a vehicle from straight-line motion
Most often this is due to different tire pressures, incorrect wheel alignment or incorrect bearing clearance. These problems are resolved by checking and adjusting the characteristics to suit normal operation.
In some cases, even disassembling the suspension using specialized equipment is required. For example, if the front suspension arm of a Lada Largus is severely deformed, then the entire axle will need to be replaced.
It is worth noting that tire defects may not be immediately noticeable, so you should swap the wheels of the front of the car. If the direction of care changes, then the problem is in the condition of the rubber. When the loss of strength of one of the springs is to blame, it will immediately compress, affecting the visual tilt of the car body.
Vertical oscillation of the front wheels
This situation most often develops during braking or accelerating to maximum speed. The passenger car begins to tilt, and under the influence of road unevenness it makes oscillatory movements. This is justified by a possible imbalance of the wheels, settling of the suspension springs or failure of the shock absorbers.
In this case, the anti-roll bar may simply not work during acceleration and braking. Here you should check the condition of all parts and, if they are worn, replace them by securely tightening the fixing bolts.
Such vertical vibrations are unacceptable, since the chassis and steering perceive them as natural dynamic loads, which ultimately leads to loss of controllability.
Modification of the rear wiper
Unfortunately, the rear wiper operating mode on the Lada Largus does not have an intermittent mode - when turned on, it works constantly.
To switch the wiper to work with a variable pause, use:
- wiper relay marked 723.3777;
- standard 4 or 5-pin connector for automotive relay;
- round terminals;
- terminals 3 mm wide (“male + female”);
- pieces of wire;
- heat shrink tubing for insulating connections.
To connect an additional relay, ground wires are used that have black markings on the steering column switch block (third from the right on the side of the wires), as well as turning on the rear wiper (white, second from the right) and turning on the rear washer (gray, far right).
The rear wiper of Lada Largus can be modified by installing an additional relay
An additional relay is installed in the gap between the block and the wire route. At the same time, in order for the electrical circuit to be returned to its original state without any problems, standard connectors and terminals are used to connect an additional relay.
The principle of the modification is that when the rear wiper is turned on, the voltage previously supplied to it directly is now supplied to an additional relay, which, after modernization, controls the operation of the wiper, providing the necessary pause between strokes.
An additional advantage of using this relay is that when the rear washer is turned on, the wiper automatically switches to continuous operation mode, and after 3-4 cycles it again switches to pause mode.
The entire structure is mounted next to the steering column switch and secured with plastic clamps.
Modernization of the body of the Largus model
We have seen that in some cases it is not difficult to transform the characteristics of a motor, although an infusion of a certain financial resource is required.
What should an owner do if he is “satisfied” with the modernized engine, but is not satisfied with the appearance of the body? Here the saving measure will be a transformation in the exterior of the Lada Largus.
In this case, you can also lean towards two courses of action:
- perform structural transformation of body components;
- so-called cosmetic modification.
The first option involves replacing some body elements with new products, usually of an individual design. Note that a well-executed modification of this nature can not only significantly transform the exterior of the car, giving it speed and sportiness, but also significantly improve aerodynamic performance.
The most common structural modifications that most owners of Lada Largus Cross are inclined towards are the following:
- spoiler installation;
- installation of body kit on the hood (linings, buckets, intakes, etc.);
- replacing head and rear optics with more advanced and powerful lighting designs;
- the use of reinforcing components around the perimeter of the body (front grille, protective linings, skirts, etc.);
- installation of new wheels complete with tires instead of standard products;
- replacement of bumpers, exterior mirrors, etc.
Naturally, such transformations cost a lot of money and require the allocation of significant time resources.
A simpler version of the transformation will be cosmetic tuning. It involves the implementation of activities in the following areas:
- updating the paintwork of the body;
- tinting of glass, as well as optical devices;
- airbrushed designs on body panels;
- wrapping the body with various polymer materials (carbon films, vinyl, etc.);
- use of additional LED lighting sources.
Such events can provide the Lada Largus Cross with an updated look, allowing it to stand out in the gray mass of traffic. The main advantage of this method is its low cost.
Mechanical conversions
If the owner is interested in global improvements to the unit, then he should resort to the mechanical upgrade option. Such a modification can significantly improve the characteristics, and this is a “plus” of 10-40% to the standard parameters.
This transformation is carried out by replacing some parts in the unit. As a rule, the following components are subject to modification:
- fuel supply system;
- elements of the gas distribution mechanism;
- injection components;
- parts of the cylinder-piston group and the block head.
Here we recommend taking into account an important aspect: components should be replaced only with analogues that are structurally compatible with this unit. Otherwise, there is a risk of motor damage.
Tuning Lada Largus - photo
One of the fruits of the joint cooperation between AvtoVAZ and the Renault/Nissan alliance is another clone of the Renault Logan car. This time in Togliatti they firmly grasped the Logan station wagon design and decided to replenish their model range in this way. The car was named Lada Largus. We will talk about improvements and improvements in it today.
Largus or Logan?
Of course, every car has something to improve, and Tolyatti models, like no other, require not just tuning, but radical improvements. Tuning the Lada Largus, the photo of which we presented on the page, is simplified by the fact that the car in its design uses virtually the same components and assemblies that are installed on numerous Dacias and Renaults, as well as Ladas. This also leads to a huge number of kits for external tuning, for tuning the interior and for refining the main problem components of the car.
Since Largus is a relatively modern model, first of all it’s worth understanding the electronics and engine control systems.
You won't get a sports car from a Lada, since a station wagon is not the best object to give it sporting characteristics. The main thing about it, perhaps, is efficiency with acceptable dynamics.
Let's try to use chip tuning to improve these qualities.
Engine chip tuning
Like most modern cars, Largus has an electronic engine management system. If you make some changes to the ECU software, you can slightly increase power and reduce fuel consumption. This will be relevant both for new cars and for cars that have already passed more than one kilogram of road dust through the filter.
An unconditional condition for chip tuning of the Lada Largus is the complete serviceability of all engine systems and components. If during diagnostics the computer shows errors or deviations from the nominal characteristics, it is worth first eliminating the faults and only then proceeding with flashing the computer.
The effect of engine chip tuning
Reconfiguring the parameters of the electronic control unit can only cause harm if the car’s ignition is not set, the fuel supply system is not adjusted, the air filter is clogged or the oil filter does not perform its functions.
Chip tuning should only be performed by a professional auto programmer, and the original ECU settings should be saved for the possibility of subsequent restoration if the need arises.
The result of successful Largus chip tuning can be:
- reduction in fuel consumption by 0.8-1.2 liters per hundred;
- reducing the load on the transmission due to increased engine elasticity;
- slight increase in power;
- idle speed stabilization.
However, you should understand that Largus is a station wagon with a lot of weight and a not very aerodynamic body, so you shouldn’t expect miracles from chip tuning.
Tuning Largus optics
Largus is not very original in appearance and the desire of the owners to change some decorative elements of the car is quite natural. Various companies produce a lot of elements for external tuning of Largus. These are kits for tuning bumpers and radiator grilles, side trims. One of the most popular areas of tuning a simple station wagon has become the replacement of standard optics.
An excellent solution to this issue would be to install French-made lensed optics, although it is not cheap. Headlights with domestically produced lenses for Largus will be cheaper, but they can also increase visibility at night, as well as make the lighting more concentrated.
Body kits and deflectors
Excellent sets of chrome body kits are produced for Largus. They not only look decent, but are also functional.
Additional chrome-plated steel sills will provide excellent protection for the body, and stylish roof rails will help place a load weighing up to 75 kg on top of the trunk.
The price of such a kit is higher than 5,000 rubles, but the functionality of the car will become wider, and such an investment will support the market value for a long time upon sale.
In addition to the fact that this is not entirely aesthetically pleasing, rear visibility is reduced, and the rear-view mirrors that are installed on the doors cannot always give an objective picture.
The solution to this issue will be the installation of a spoiler-deflector, which can direct the air flow from top to bottom and repel drops of road suspension that settle on the rear door windows.
If you approach tuning the Lada Largus correctly, the car will become a good household assistant, a stylish and modern car for little money. Successful and straight roads to everyone!
Skoda Yeti - technical specifications
Installing a handbrake warning light
The parking brake, according to reviews from Lada Largus owners, is quite powerful for this car. So attempts to move with the handbrake raised usually end in failure.
Although slightly releasing the handbrake, even after several tens of meters of movement, does not add life to the rear pads.
To protect your brake pads, install a handbrake warning light.
In order to avoid such curious mistakes when starting to drive, especially since the standard “handbrake raised” alarm lamp is not very informative, some motorists install an additional handbrake alarm unit.
The unit itself is commercially available, and its connection is quite simple.
The unit itself has four wires for connection. They all connect to a black connector that matches the instrument cluster.
Color coding and connection:
- the positive from the ignition is connected to pin 10 (yellow wire);
- a speed sensor is connected to pin 22 (green wire);
- the remaining two gray wires are connected to slot 16 (gray wire).
Now, if you start driving with the handbrake raised, a buzzer will sound and the parking brake lamp on the instrument panel will begin to blink.
Do-it-yourself modification of the Lada Largus. Let's bring this station wagon to perfection"
Do-it-yourself modification of the Lada Largus. Bringing this station wagon to perfection
Improving the family VAZ car - modifying the Lada Largus with your own hands - is accessible and necessary, probably, for almost every owner. Poorly hidden family ties with Renault are, of course, a very positive thing, affecting both driving dynamics and reliability.
However, the exterior and interior of a good family car requires possible improvements related to various components of the car (applying the finishing touches, so to speak). Moreover, there really is something to add and improve to the basic configuration!
Do-it-yourself modification of Lada Largus
It is usually produced not at all in order to make a racing car out of it.
Still, it is necessary to remember that this is a family station wagon, which was created to solve other tasks assigned to it: leisurely trips over long and short distances, out of town, with the whole family.
Here, in this model, it is rather recommended to take care of additional comfort of movement and enhanced economic performance.
This procedure is quite common for this VAZ model. With its help, you can achieve a reduction in fuel consumption and. Firmware can be useful not only for a used car, but also for a completely new one, just purchased. Before carrying it out, you need to make sure that the engine itself is in good working order by diagnosing the ECU.
If the motor is unstable, the computer will see a malfunction, even a minor one. Chipping should not be done until the flaws are eliminated. And what's the point of flashing an engine that is unstable?
With normal indicators
generated by the sensors, a new setting is uploaded to the on-board computer, allowing you to control injection, ignition timing, and other parameters that greatly affect the dynamic performance and power of the engine.
Ask that the previous programming option be saved as well, just in case. Thus, with the help of chipping we can eliminate “short” gears, achieve smoother acceleration of the car, and more confident “pickup”.
This saves the life of the engine and clutch.
What can we say about gasoline consumption? It can decrease by 1.5 liters! When tuning, complaints about the air conditioner should disappear, which, before changing the settings, usually “presses” the engine under load.
Related article:
«».
However, we should not forget that a station wagon with a heavy body, not very aerodynamic, with a 1.6 gasoline engine naturally has an increased fuel appetite. So tuning can only improve, and not radically change, the situation.
Firstly, they improve the car's optics. Instead of the standard one, which is both more powerful and will significantly increase the safety of night driving. And yet, such an innovation brings the exterior to a modern standard.
Secondly, it is glued on, giving the body a more original, modern look and, moreover, protecting it from minor bruises and scratches. It should be remembered that you should not get carried away with carbon. Everything should be in moderation. It is enough to paste over the hood and body pillars - and your car will no longer be recognizable!
Among the most popular innovations are the front end trim and the replacement of the radiator cap (for those who like a more solid appearance of the car). It is also possible (it is also good from a practical point of view - it protects the coating from chips and cracks).
You can also install chrome body kits, sold as a set. And there are roof rails on the roof. And also spoilers that perform aerodynamic functions.
To external tuning
can also be attributed to Largus. Some are additional and even bottoms. But this is already entertainment for lovers of night walks around the city. Using an LED strip attached to parts, you can achieve a stunning “cosmic” effect.
A real family car should be quite comfortable inside too. Such a modification of the Lada Largus can be added to the basic assembly with your own hands.
- Install an instrument unit with data digitalization;
- Additionally, illuminate the huge trunk using LEDs;
- Replace the driver and passenger seats with sports ones, with lateral support, more comfortable for long trips especially;
- Modification of the air conditioner - installation of a cabin air filter;
- Factory sound insulation leaves much to be desired. Therefore, you can make an additional one so that less noise penetrates into the cabin.
Operation of electric windows when the ignition is turned off
Quite often, Lada Largus owners complain that the power windows do not work when the ignition is off or the key is in ACC. This can be corrected by a small modification of the car's electrical circuit.
Video on how to make power windows work on a Lada Largus without ignition:
To perform this work, you must remove the interior fuse box.
It is worth recalling that this modification, like the previous one, must be carried out with the battery disconnected!
First of all, you need to find fuses F13–F16, which are responsible for the functionality of the ESP, after which, carefully bending the terminal clamps and pulling out the plastic clip, remove the power supply strip.
The removed strip is divided transversely into two parts. The first part returns unchanged to the place corresponding to fuses F15 and F16.
A thick copper wire with a cross-section of approximately 1.5 squares is soldered to the remaining second half, which, in turn, is soldered (screwed) to any thick wire that receives power when the key is turned to the ACC position (or has constant voltage - as you like).
The modified half of the strip is installed in place, the mounting points are isolated, the fuses are returned to their place and reassembly is carried out in the reverse order of disassembly.
Hello, dear friends! Today we will be a little creative, reflect and prepare the ground for further action. And why all? Yes, because the topic of our conversation will be tuning the Lada Largus.
This is a popular car in Russia and the CIS countries, which is closely associated with the French auto company Renault and received a lot from it. Therefore, the current Lada Largus compares favorably with outdated domestic station wagons.
Yes, Largus is a full-fledged station wagon or van, as some are used to saying. Even the presence of the prefix Cross in the name does not make it a full-fledged crossover.
I would like to discuss with you possible improvements for the Lada Largus, and also separately tell you a little about the Cross version. If you are ready, then we can begin.
Tuning the station wagon's interior
Let's start with the driver's seat. What interior elements come into the driver's field of vision most often? One of them is the instrument panel. Unfortunately, it doesn’t look very modern on Largus, so a more stylish solution is offered as an alternative. The photo shows an instrument panel with digital data display.
Another way to modernize the interior is to install additional lighting in the trunk of a station wagon. This solution will significantly simplify the loading/unloading procedure at night. As a rule, this task can be accomplished using a cheap LED strip, which is powered by the standard luggage compartment lighting.
The seats... They seem to be quite good, but during long trips they make themselves felt. If you use the car in city mode, the seats do not cause any complaints. But for those who regularly have to go on trips of several hundred kilometers, we recommend that you think about buying better quality seats with good lateral support.
The Lada Largus has air conditioning, which is very good. But the problem is that the air is not filtered. The car simply does not have a cabin filter. There are a lot of tips on the Internet on how to install a cabin filter on a Largus with your own hands.
Another drawback of the car, which can be solved with the help of tuning, is the lack of high-quality sound insulation. Of course, many perform the procedure on their own, but in most cases it is much more advisable to entrust the matter to real specialists.
Autopub wrote earlier about how to improve the sound insulation of a car with your own hands:
- sound insulation of doors;
- sound insulation of wheel arches;
- hood soundproofing.
We extend the car’s equipment, improving and changing the appearance
Tuning is traditionally done either with your own hands or in a car repair shop.
New elements can be produced individually, or they can be “serial”, factory-made. But, for example, a trunk extractor shelf, which is installed at the factory only in the “luxury” version, can be installed on simpler versions of the car if you purchase it additionally.
The same interesting elements are the armrests for Largus passenger seats, which have a box and a retractable part.
And also an armrest for the Lada Largus, which is placed on the driver’s seat, dividing the space between him and the passenger.
When it comes to a new car, you need to weigh your desire to become a Kulibin many times.
Additional lighting of the floor (at the feet of passengers and the driver) and the luggage compartment, which is carried out at the place where the door opens, can be provided by an official VAZ dealer, giving a guarantee.
Returning to the “family” nature of the Lada Largus. Roof rails for the Lada Largus, designed for transporting large equipment and installed on the roof, are extremely popular among car owners who purchased a car for a specific purpose: traveling with their family.
Additionally, you can purchase and install aerodynamic cross members with a specially designed noise-free profile and an anti-vandal key.
A cargo basket on the crossbars may come in handy; it is convenient for transporting bulk or oversized small cargo over long distances.
The appearance of the car is truly changed by such a utilitarian thing as a removable additional luggage compartment, in other words, a roof box
Lada Largus car boxes differ in their load capacity, shape, size and volume. This device for cargo transportation is indispensable in adverse weather.
The list of accessories for road transport can be completed with a rack for transporting bicycles for Largus and a tow bar.
Chip tuning of Lada Largus car
This practice is quite common and most owners use it successfully. The essence of the transformation is as follows: by changing the settings of the electronic unit, we achieve adjustments to the characteristics of the motor. With proper calibration of certain parameters, you can get a very decent result, after which the car will drive noticeably more vigorously.
Chip tuning is performed by specialized workshops. They reprogram the standard firmware version to another one. Depending on the needs of the owner, you can install a program that will provide the motor with a specific set of modified characteristics. So using the firmware you can achieve the following results:
- reducing fuel consumption;
- reduction of exhaust toxicity;
- increasing acceleration dynamics.
Carrying out this procedure with your own hands is undesirable even for an experienced owner, since it can lead to a lot of side effects. Here you should entrust your car to professionals. If the modification is carried out efficiently, then the owner will say goodbye to a sum of approximately 4-10 thousand rubles, which is not a catastrophic waste.
As a result of chipping, the characteristics of the motor change, however, by an insignificant amount.
Improving the motor
When considering such a car improvement as tuning the Lada Largus model, it is initially recommended to look towards the technical characteristics. The motor should receive special attention. The power of the unit varies from 84 hp. With. up to 102 “horses”, depending on the design features of the block heads and unit settings. This is enough for family owners for everyday driving. However, among the owners of Lada Largus there are many who are not entirely satisfied with the standard engine capabilities. There are quite a lot of reviews online about the poor dynamics of this car. The existing shortcoming can be leveled out if you are thinking about tuning the engine.
Here the owner has two options available to him:
- perform chip tuning of the electronic control module, after which the settings will change;
- modify the unit mechanically, which implies constructive intervention in order to replace components with reinforced analogues.
Here we will dwell in more detail on both options for modifying the Lada Largus Cross unit. Let's start with the chip.
VAZ articles and choice of tools
The standard floor covering in a van consists of two halves. They are fastened with countersunk screws (see photo).
Body before modification
Screws 2 here are designed for Torx T40 keys. A T30 wrench will fit the small screws.
No one bothers you to unscrew a couple of screws on each side in order to press the flooring with them. The hat is hidden and you don’t have to buy anything. Part numbers: 7703008207 – T30 self-tapping screw; 7703008162 – T40 screw.