Bolt pattern for VAZ 2112 - what kind of bolt pattern for VAZ

In all modifications of the VAZ 2110, the bolt pattern in the factory configuration is 4x98. “Dozens” rolled off the assembly lines with stamped wheel disks - diameter R13, as well as with cast ones - diameter R14.

The wheels were fitted with tires measuring 175/70 R13 or 175/65 R14. However, if the sizes of wheels and tires are relatively clear values, then what a bolt pattern is is a big mystery to many.

Wheel parameters and bolt pattern for VAZ 2110, 2111, 2112

Tips for selecting stamped products

On a note.
Wheel rims that are made using a method such as stamping can easily be called the most common for cars. Frequent installation of just such wheels is associated with the simplicity and low cost of manufacturing products of this type. VAZ 2112 on stamped rims with plastic caps

Forged wheels are not attractive in terms of design and have poor performance, but are inexpensive.

As for installation requirements, in this case they are identical to cast products. It is necessary to ensure that the parameters and dimensions of the fasteners and overhang match.

Preparing for adjustment

Most often, the VAZ 2110 camber and alignment are installed at a service station, but you can do it yourself. First of all, check whether there is play in the bearings and whether the steering is loose. At the same time, check the diameter and absence of deformation of the disks, air pressure in the tires, and tread wear.

VAZ 2110 front suspension assembly diagram

Naturally, if a wheel is loose, action will need to be taken, and one with improper tread wear may need to be replaced. Wheels standing on the ground need to be pulled relative to the vertical. If you find any play, have a helper apply the brake and check the play again.

If it disappears, the bearing needs to be replaced. If after this the size of the play not only does not disappear, but only decreases slightly, the suspension needs to be checked, repaired, and sometimes replaced.

Front wheel hub diagram

After this, hang the wheel and check the play again. It is possible that the play has disappeared, but the wheel turns jerkily or is simply difficult, then you need to slightly expand the diameter of the bearing installation site.

Rear suspension

If you hear a grinding noise, the bearing needs to be replaced.

VAZ 2112 2112x 2006 1.8i

Wheel and rim sizes for the Lada Granta all wheel parameters: pcd, offset and rim size, drilling
Generation: 2112xEngine: I4, GasolinePower: 98 hp
(72 kW) Wheel bolt pattern parameters

What wheel sizes does the manufacturer recommend to install?

The VAZ 2112 2112x 2006 1.8i is equipped with 5Jx14 ET35 rims assembled with 175/65 R14 82H tires as standard. Where:

• 5J - rim width in inches;
• 14″ — tire diameter in inches;
• ET35 - disc offset in millimeters.

The vehicle tire marking 175/65 R14 is deciphered as follows:

• 175 — profile width (cross section of the tire) in millimeters;
• 65 — profile height as a percentage of its width;
• R - radial cord winding;
• 14 is the tire diameter in inches.

In addition, information about its load capacity and speed parameters can be printed on the rubber - load index and speed index. The load index is a two- or three-digit number; the speed index is indicated in Latin letters, for example 82H:

• 82 - maximum permissible tire load 475 kg;
• H — maximum permissible vehicle speed is 210 km/h.

Using the recommended tire sizes will help you avoid problems with handling, safety and other difficulties. What non-standard sizes can be supplied? Refer to the table; it indicates possible acceptable alternative sizes for tuning. Although there are other options that we have not described in the table. For example, wider discs of the same diameter. Or install wheels of the same width, but with a larger diameter, which is quite popular among car owners. The choice of discs is huge; you can find copies with the same parameters, but with an overhang 1-2 millimeters more or less. It is not possible to list all the options.

At the same time, the bolt pattern for all types of wheels is the same - 4x98. Thus, all disks are mounted on four bolts and the distance between them is exactly ninety-eight millimeters. The diameter of the car's hub is 58.6 mm.

Standard tire pressure is 2 MPa.

Why is it important to choose the right size?

The most popular wheel sizes for installation are R14 and R15. This is due to the fact that they can be easily selected in a store and installed on a car. The main thing is to comply with the required dimensions and bolt pattern parameters specified by the manufacturer. If products with dimensions different from the factory ones are selected, then special adapter rings should be used. They often come with the product.

You might be interested in this About the bolt pattern characteristics of Mazda wheels

Adapter rings for wheels for VAZ 2112

Note!

The main problem that prevents the installation of large products is the size of the wheel arches.

If you exceed the dimensions and do not modify the wheel arches, then the rubber will touch the body structure itself during maneuvers, which leads to increased wear of all suspension components and parts and a decrease in safety.

To avoid these difficulties, it is necessary to install products only with guaranteed suitable parameters and dimensions. For the VAZ 2112, these are the diameters R14 and R15, which have factory parameters and meet all safety requirements and other characteristics.

Wheels of this size will give the car the best level of driving comfort.

As for increasing the size of the rim, their operation has its positive and negative sides, which every car enthusiast needs to know. However, the decision to purchase and replace disks should be made only by the owner of the machine.

Pros:

• Good car behavior in the lane;
• Improving the exterior of the car;
• The best road qualities, including dynamics and handling;
• Maximum absorption of potholes and road defects;
• When using rubber with a high profile, the wear resistance of chassis parts increases;
• Reducing the braking distance.

Minuses:

• Reduced level of comfort in motion. This is due to the high sensitivity of the chassis to road defects;
• Difficulty in parking and driving on poorly paved roads;
• Increased requirements for pressure control in low-profile tires;
• Increased gasoline consumption, which is associated with the increased difficulty of driving the wheels;
• High price.

What is a bolt pattern?

Lada Priora wheel size, rims, tires

4 bolt holes are 4

• The first number “4”
  indicated in the parameters indicates the number of holes located on the hub, intended for screwing wheel bolts into them.
• The second number “98”
  indicates the diameter in millimeters of the circle in which those same mounting bolts are located.

Wheels from Logan (bolt pattern 4*100)

Based on safety requirements, wheels with such a bolt pattern cannot be installed on a VAZ-2112. But, some drivers use spacers or eccentric bolts

install such disks.

All car enthusiasts come into contact with the installation or replacement of wheel rims. Sooner or later, for various reasons, most car enthusiasts were faced with the problem of choosing new wheels. The reasons may be different - damage to the standard disk, tuning in the form of installing disks of larger diameter, other reasons.

When replacing, you should be guided by certain compatibility parameters; not every disc, even one of a suitable radius, will fit any car model. One of the important parameters when choosing rims is their bolt pattern.

conclusions

It’s not at all difficult to understand such parameters, the main thing is to remember them and choosing suitable wheels ceases to be a difficulty.

Dull VAZ stamped wheels are often hidden behind elaborate plastic caps. And for good reason. Every owner of a VAZ-2110 wants his car to stand out from the mass of gray and black dozens.

One of the ways to improve the appearance of a car is deservedly considered to be replacing the wheels. Not many people think that when selecting a replacement disk, you need to take into account not only the number of mounting holes. Today we will look into the bolt pattern of VAZ-2110 wheels and select several options for a simple and bloodless replacement.

VAZ 2112 2112x 2003 1.5i

Tire and wheel sizes for Lada Priora 2008

Generation: 2112xEngine: I4, Gasoline Power: 77 hp
(57 kW) Wheel bolt pattern parameters

What wheel sizes does the manufacturer recommend to install?

The VAZ 2112 2112x 2003 1.5i is equipped with 5Jx13 ET35 rims assembled with 175/70 R13 82T tires as standard. Where:

• 5J - rim width in inches;
• 13″ — tire diameter in inches;
• ET35 - disc offset in millimeters.

The vehicle tire marking 175/70 R13 is deciphered as follows:

• 175 — profile width (cross section of the tire) in millimeters;
• 70 - profile height as a percentage of its width;
• R - radial cord winding;
• 13 - tire diameter in inches.

In addition, information about its load capacity and speed parameters can be printed on the rubber - load index and speed index. The load index is a two- or three-digit number; the speed index is indicated in Latin letters, for example 82T:

• 82 - maximum permissible tire load 475 kg;
• T — maximum permissible vehicle speed is 190 km/h.

Using the recommended tire sizes will help you avoid problems with handling, safety and other difficulties. What non-standard sizes can be supplied? Refer to the table; it indicates possible acceptable alternative sizes for tuning. Although there are other options that we have not described in the table. For example, wider discs of the same diameter. Or install wheels of the same width, but with a larger diameter, which is quite popular among car owners. The choice of discs is huge; you can find copies with the same parameters, but with an overhang 1-2 millimeters more or less. It is not possible to list all the options.

At the same time, the bolt pattern for all types of wheels is the same - 4x98. Thus, all disks are mounted on four bolts and the distance between them is exactly ninety-eight millimeters. The diameter of the car's hub is 58.6 mm.

Standard tire pressure is 1.9 MPa.

What non-standard sizes can be supplied?

Wheel parameters and wheel bolt pattern on a Chevrolet
Installing wheels with a diameter and width greater than the standard size may cause a malfunction. Before purchasing, you must ensure that the installation is safe. A good solution is a preliminary “trying on”. You should install the wheels before purchasing

It is especially important to check the front tires: they should not touch the fender liners or the car body

Often, too high a tread height leads to contact with the fender liners. This can have serious consequences:

• damage to the plastic of the wheel arches;
• mudguards become damaged and cease to perform their function;
• Cavities and rust appear at the points of contact between the tread and the paintwork.

The latter is especially dangerous. Since unprotected metal rots quickly, literally within 1 winter. AvtoVAZ cars have never been famous for their high-quality anti-corrosion treatment. Also, increasing the weight of the wheel by literally a few kilograms will lead to accelerated wear:

• wheel bearings;
• shock absorber struts and other suspension elements.

The manufacturer allows the installation of the following non-standard tire diameters on VAZ 2110 vehicles and modifications:

• R15;
• R16;
• R17.

The diameter of R14 is typical and relatively small. It is allowed to use tires with a tread width of up to 185 mm and a height of up to 75-80. Tires with a diameter of 15 inches are also usually installed on this car without any problems. R16 is a tire that requires some driving skill. Since this diameter is not standard, the machine is not designed for this weight and size.

R17 and R18 can only be installed after some modification using a special roller - the wheel arches simply “roll out”. This will avoid contact between tires and body parts. Also, constant friction of the tread on the fender liners will cause the pattern to quickly wear off and lead to deterioration of the wheel’s grip on the road.

Manufacturers

The domestic industry produces several types of rubber suitable for LADA 112. Tires that are in good demand today are:

• Kama - in Russian and European versions.
• Cordiant.

Many VAZ 2112 owners prefer to put foreign-made tires on their car. The most popular are:

• Yokohama,
• Bridgestone
• Goodyear
• Nokian Hakka Green,
• Michelin.

When choosing tires, it is very important to consider the quietness of the rubber. If it makes a loud sound, the ride comfort will be lost.

It must be said that when choosing tires, it is also necessary to take into account what roads the VAZ will drive on, driving style and travel distance.

Rules for selecting Torus alloy car wheels

R13 wheels: what they are, which wheels are best to choose
The Torus casting may not require replacement for many years, but only if the components are chosen correctly. Most consumers are interested in the diameter, this is a mistake. Alloy wheels "Turus" have many subtleties that affect not only the strength of the product, but also traffic safety. The quality of components determines:

• tire service life;
• hub endurance;
• endurance of neighboring technical hubs.

Mistakes are fraught with force majeure on the road and rapid wear of car components. The main mistake car owners make is purchasing a set of tires that are too large.

Disc offset

In the race to follow trends for non-standard solutions, car owners neglect the advice of specialists. As a result, the rubber is too large and simply begins to wear off on the body of the vehicle. The problem also concerns the negative impact on body elements. And painting a car is an additional level of spending money

When choosing, it is important to consider the operating characteristics and materials. It is important to remember about wheel offset, which can be:

A suitable cast version does not need to be adjusted. Otherwise, after just a couple of days of use, the element will begin to bend, and the car’s handling will become significantly worse.

You cannot save money on purchasing discs. Car wheels experience serious overloads, especially on highways. Economy solutions with positive wheel offset quickly become scratched, cracked and deformed.

Torus branded models are reliable, the main thing is to choose the appropriate size. The company uses high-quality materials designed to withstand the heavy weight of the car and significant mechanical shocks. Experts recommend purchasing a set of 4 wheels at once - tires plus original wheels. This is an expensive option, but the car owner does not have to worry about safety on the road.

Car disk washing

The included parts have a high-quality fastening system and thoughtful design. Also, in order to preserve the discs for as long as possible, you need to take care of the elements. No special care is required; car owners should follow simple recommendations:

• Use only mild detergents when washing your car, without ammonia.
• After a car wash, cast models should be allowed to dry; if there is no time, you can wipe them thoroughly with a soft cloth.
• Water-repellent preparations or polishes can be used. Their use will protect the coating and maintain aesthetics.

Tori discs have proven themselves well. You can buy car parts in specialized stores. If you have any problems with the choice, an expert will definitely help, and the car will be “put on” with the original “Toruses”.

Wheels for Lada Priora

Lada Priora is a C-class car, manufactured in hatchback, sedan and station wagon body styles. Lada Priora has improved sound insulation characteristics, the suspension is adapted for domestic roads, the cost of parts is 10–15% lower compared to foreign analogues.

Despite a number of disadvantages in the design, the model remains the most popular in the CIS. According to theft statistics, Lada Priora also occupies a leading position.

Second generation Lada Priora

At the end of 2013, the second generation of Lada Priora was released. The updates affected not only the interior, power plants, but also the exterior. The versions remain the same “Standard”, “Norma”, “Lux”, but with minor changes.

Rim material: low alloy steel, galvanized metal. Factory warranty for anti-corrosion protection for six years.

What kind of disks can be installed?

The size of wheels, tires, disks that are installed on a car have a direct impact on its technical characteristics. In the instruction manual, the manufacturer indicates the recommended dimensions, as well as acceptable ones.

The owner of the vehicle, in our case Lada Priora, independently decides what type and size of wheels and tires to install. For the average driver who uses the car as a means of transportation to and from work, the factory rim sizes are more than enough.

In case of tuning, changes in standard characteristics, dynamic indicators, it is necessary to refit the car with non-standard wheel sizes.

List of characteristics that can be changed by installing non-standard wheel sizes:

• Controllability;
• Road grip;
• Sharp and responsive steering wheel;
• Reduced/increased aquaplaning;
• Comfort of movement;
• Noise level;
• Combined cycle fuel consumption (see photo);
• Tread wear rate.

Compatible wheel sizes for Lada Priora

R14:

• Width:175, 185, 195, 205;
• Profile height: 45, 50, 55, 65;
• Rim diameter: 14;
• Design type: R – radial.

R15:

• Width: similar to the previous parameters;
• Profile height: from 40 to 55;
• Rim diameter: 15;
• Construction type: similar to the previous ones.

R16:

• Width: from 175 to 205;
• Profile height: from 40 to 50;
• Rim diameter: 16;
• Construction type: similar to the previous ones.

R17:

• Width: from 175 to 195;
• Profile height: 40, 45.

Recommendations for storing and caring for discs

• During a routine technical inspection, check the geometry and balancing of the wheel on a special diagnostic stand. If deviations are detected, restore the integrity of the structure;
• If cracks or dents form on the rim, immediately contact a service station for preventive maintenance;
• Avoid hitting road potholes at high and medium speeds.
  Regardless of the material or workmanship, the disk will be deformed and the seal will be compromised;
• Monitor the tire pressure; it should not be lower/higher than recommended by the manufacturer. If it deviates, pump it up;
• Switch to summer/winter mode in a timely manner.
  This means that in summer the tire pressure is 0.15 atm higher, and in winter it is lower by the same amount. The parameters are specified in the vehicle operating instructions;
• Tighten the rim nuts with a torque wrench. Excessive tightening contributes to the breakage of the studs, weak - an emergency situation, unscrewing the wheel.

Care

In dry, sunny weather, cast aluminum wheels are least susceptible to external damage. But in slush, ice, when the road is strewn with various chemicals, the rim is most susceptible to corrosion. This provokes paint peeling and destruction of the molecular composition.

Wash your wheels as they get dirty. Since it is unlikely that you can clean it properly with a rag, use high-pressure compressors. Equipment of this class is available at many service stations, workshops, and service centers.

Systematic polishing allows you to get rid of scratches and burrs. First clean the wheel from dirt, dry it thoroughly, and then treat it with a chemical. Wipe several times with a microfiber cloth.

Store the wheels in a hanging position without touching each other. Pre-clean them, dry them, and wrap them in cellophane.

General background information

Ranges of possible values ​​for tires and wheels VAZ 2112 2003.
Tires

Wheel disks

Photo

Expert advice

When choosing tires for a car, you must first follow the manufacturer's instructions. Ask yourself a few questions.

• On what roads will the car be primarily used?
• Do you need increased cross-country ability?
• How much of the route will be city roads and how much will be highways?
• Will the vehicle carry heavy loads?

The answers to these and similar questions will help determine which tire parameters you need to pay special attention to.

How to choose the right wheels for a VAZ 2112 2003?

3 types of rims:

• Stamped (economical price category) - made from a sheet of iron by stamping on a press.
• Light alloy - manufactured by casting (more reliable than stamped ones).
• Forged (the highest quality and more expensive than the previous ones) - made from light alloys by stamping at high temperatures.

The choice depends on financial capabilities. However, it should be borne in mind that the quality of the road surface on which you have to drive every day must also be taken into account.

So, if it gets into a hole, a stamped disk will bend and will not cause harm to the tire, but a forged or cast one can cut it. There is a possibility that the cast disc may burst or crack.

It should also be noted that repairing “stamping” wheels is cheaper than repairing cast or forged wheels. But wheels with high-quality cast and forged disks kill the suspension less, because lighter and have more perfect geometry (better balanced).

The same wheels may or may not rub with tires on the same car - wheel alignment adjustment will help here.

What is the tire pressure?

It is the driver's responsibility to constantly monitor tire pressure. This will avoid standard problems associated with vehicle operation. An abnormal pressure value often causes:

• deterioration of management;
• uneven tread wear.

Often the car owner independently reduces the pressure in the wheels of his own vehicle. This reduces the load on the suspension, and the car “passes” various road irregularities an order of magnitude easier. But it is worth noting: a decrease in pressure even by 0.1 MPa leads to serious problems. The main ones include:

• increased fuel consumption;
• rapid wear of the outer tread segments;
• the car becomes less maneuverable.

An overinflated wheel causes no less problems. The central part of the cylinder begins to wear off quickly. In addition, at ambient temperatures of more than 60 degrees Celsius, the tire may simply explode. Which will lead to driving into the oncoming lane.

Standard wheel sizes for LADA Priora 1.6i 217x

The LADA Priora 1.6i 217x model was produced from 2007 to 2013. Table of standard and suitable wheel sizes for LADA Priora 1.6i 217x.

Disc drilling parameters are usually called bolt pattern:

• LZ (number of holes)
• PCD (hole center circle diameter)
• ET (disc offset)
• DIA (hole diameter)

Useful articles and reviews Announcements of certificate drawings among subscribers. Subscribe to VK group

Is it possible to install wheels with an unsuitable bolt pattern?

Some motorists, in an attempt to save on the purchase of spare parts with the necessary parameters, purchase products that do not correspond to the car brand. Such wheels are subjected to self-processing, the hub hole is widened, the location of the bolts is changed, and then they are installed on the car.

Theoretically, such a modification is possible, but the work must be carried out with maximum precision. It is impossible to measure a disc so correctly in a garage. And inaccurately drilled cutouts lead to wheel runout, destruction of the hub and suspension elements, and disruption of vehicle stability on the road.

Competent modification of the car in conditions close to factory ones is not economically feasible. The work will cost more than purchasing a wheel that initially matches all sizes.

When choosing rims, the owner must pay close attention not only to the diameter of the rim, its weight and design, but also to important technical parameters. One of the key parameters for the compatibility of the disk and the vehicle design is the bolt pattern parameter

This component is a value (the typical value for the vast majority of VAZ cars is 4/98) that determines the number of mounting holes (the first indicator) and the diameter of the circle of the distance between the holes (accordingly, the second indicator).

Disc options

The modern market for wheels for the VAZ-2115 is quite extensive and includes different designs and models. At the moment there are three main groups of disks:

• steel;
• cast;
• forged.

Steel wheels

As a rule, when producing cars, AvtoVAZ equips them with steel wheels. But their appearance very often confuses car enthusiasts, so they are not particularly popular. The main advantage of such discs is their low price.

Since stamped steel wheels are very cheap, but their appearance leaves much to be desired, there is a need to additionally purchase plastic or rubber caps. The technical characteristics of these wheels are truly excellent, as the car behaves confidently on the road, maneuverability increases and braking distance decreases.

You should choose such wheels based on the technical characteristics and equipment of the VAZ-2115. To install the disks, you do not need to buy anything additional, because the kit already contains the necessary bolts, nuts and studs. For a more presentable appearance, you can purchase caps.

Alloy wheels

For the manufacture of cast wheels, a light alloy with admixtures of aluminum and magnesium is used. The biggest advantage of these wheels is their appearance. A wide selection of designs allows you to satisfy any car owner. The cost of such disks is slightly higher than steel ones, but much cheaper than forged ones. Therefore, car enthusiasts are increasingly choosing these models.

First of all, when choosing alloy wheels for a VAZ-2115, you should immediately pay attention to the bolts. Often the center hole is slightly wider than the standard bolts

To avoid problems with installing disks, you must additionally purchase an instep support (spacer).

Choosing a suitable arch support is easy when you take into account two parameters:

1. The external size must match the size of the central hole of the disk.
2. The internal size should be commensurate with the hub.

For example, the central hole of the selected disks is 67.1 mm, the hub is 58.6 mm, therefore, it is necessary to purchase an instep spacer measuring 67.1-58.6 mm.

For alloy wheels, you should buy bolts with smaller heads, since regular bolts are somewhat wider and simply will not fit the holes. In any specialized store you can find a suitable option for a particular disc. Considering these nuances, installing alloy wheels will not take much time and effort.

Advantages of alloy wheels

Alloy wheels are universal and suitable for most vehicles, including the VAZ-2115. The advantages over steel models are obvious, as they:

• Lighter, self-cleaning and does not rust.
• Alloy wheels do not require caps and the car's handling becomes better with them.
• Properly distribute the load on the suspension.

Advantages over forged wheels:

• Affordable price segment.
• Wide choice of designs.
• Fairly light weight.

Forged wheels

The most expensive model on the modern market is forged wheels. They are made from light alloy material under high pressure. At the same time, to obtain the required shape, the disks are processed using special high-precision equipment.

Forged models are characterized by high strength, which exceeds established standards by almost 2.5 times. Therefore, when sports tuning a VAZ-2115, it is better to use this type of disc. If the car is used as usual, then it is recommended to opt for more budget options.

General background information

Tire and wheel sizes for VAZ 2112 2000

Ranges of possible values ​​for tires and wheels VAZ 2112 2000.
Tires

Wheel disks

Photo

Expert advice

When choosing tires for a car, you must first follow the manufacturer's instructions. Ask yourself a few questions.

• On what roads will the car be primarily used?
• Do you need increased cross-country ability?
• How much of the route will be city roads and how much will be highways?
• Will the vehicle carry heavy loads?

The answers to these and similar questions will help determine which tire parameters you need to pay special attention to.

How to choose the right wheels for a VAZ 2112 2000?

3 types of rims:

• Stamped (economical price category) - made from a sheet of iron by stamping on a press.
• Light alloy - manufactured by casting (more reliable than stamped ones).
• Forged (the highest quality and more expensive than the previous ones) - made from light alloys by stamping at high temperatures.

The choice depends on financial capabilities. However, it should be borne in mind that the quality of the road surface on which you have to drive every day must also be taken into account.

So, if it gets into a hole, a stamped disk will bend and will not cause harm to the tire, but a forged or cast one can cut it. There is a possibility that the cast disc may burst or crack.

It should also be noted that repairing “stamping” wheels is cheaper than repairing cast or forged wheels. But wheels with high-quality cast and forged disks kill the suspension less, because lighter and have more perfect geometry (better balanced).

The same wheels may or may not rub with tires on the same car - wheel alignment adjustment will help here.

What is the tire pressure?

It is the driver's responsibility to constantly monitor tire pressure. This will avoid standard problems associated with vehicle operation. An abnormal pressure value often causes:

• deterioration of management;
• uneven tread wear.

Often the car owner independently reduces the pressure in the wheels of his own vehicle. This reduces the load on the suspension, and the car “passes” various road irregularities an order of magnitude easier. But it is worth noting: a decrease in pressure even by 0.1 MPa leads to serious problems. The main ones include:

• increased fuel consumption;
• rapid wear of the outer tread segments;
• the car becomes less maneuverable.

An overinflated wheel causes no less problems. The central part of the cylinder begins to wear off quickly. In addition, at ambient temperatures of more than 60 degrees Celsius, the tire may simply explode. Which will lead to driving into the oncoming lane.

Wheels for VAZ 2112

Size

Lada 2112 or in common parlance Dvenashka was equipped from the factory with 13 and 14-inch wheels. Stamped and light alloy.

Factory tire sizes - 175/70 R13 and 175/65 R14

Wheel parameters: bolt pattern - 4X98, width - 5.0 and 5.5 J, offset - ET40-37, centering hole - CO 58.5

As a tuning option, you can install tires measuring 195/50 R15 and 205/45 R16 on wheels of larger diameter - R15 and R16.

Radius

VAZ 2112 always has 14-inch wheels. 13 won't work for her. There is a brake disc with a diameter of 14 inches. Because all 2112 are 16 valve. And only 14-inch wheels come with 16 valves.

Replacement

If a wheel is damaged, you must stop immediately in a safe place. Stopping your vehicle to change a tire on a busy road or on the side of a busy road can be dangerous.

If a wheel is damaged, turn on the hazard warning lights and move slowly and carefully along the side of the road or along the far right lane until the nearest exit to a suitable area sufficiently distant from the roadway

1. Place the car on a flat horizontal platform with a hard, non-slip surface at a sufficient distance from the roadway. Move the gear shift lever to reverse position. Apply the parking brake. If you are towing a trailer, it should be disconnected.

2. Ask passengers to get out of the car and move away from the roadway.

3. Place a jack under the car in a specially designated place next to the damaged wheel. If the car is parked on soft ground, place a wide and fairly solid support (for example, a board) under the lower support of the jack.

Note The jack must be installed only in specially designated points on the body (indicated in the figure), otherwise the body may be deformed or the vehicle may not be secured securely.

WARNING Make sure the jack is stable, otherwise the vehicle may fall off and cause personal injury. It is strictly forbidden to stand under a vehicle that is raised by a jack alone or to place your hands or feet under it.

4. Under the wheel located diagonally from the damaged one, it is necessary to place wheel chocks on both sides or, if there are no chocks, stones large enough to prevent the vehicle from moving.

5. Using a wheel wrench, loosen the wheel bolts by half a turn.

6. Using a jack, raise the car to a height sufficient to remove the wheel, and completely unscrew the wheel bolts, then remove the damaged wheel from the car. Please note that wheel bolts can be heated to high temperatures. Temporarily place the removed wheel on a platform near the car with the outer side facing up.

7. Before installing the spare wheel, thoroughly clean the adjacent surfaces of the wheel disk and hub from dirt using a clean rag.

WARNING Use caution. As a result of braking, the parts being wiped could heat up to a high temperature.

As a result of braking, the parts being wiped could heat up to a high temperature.

8. Install the spare tire. Tighten the wheel bolts by hand. Then tighten the bolts using a wheel wrench. Tighten the bolts in several approaches in a crisscross pattern. The wheel should be pressed tightly and evenly against the hub flange. Do not fully tighten the wheel bolts on a suspended wheel.

9. Lower the car and remove the jack.

10. Fully tighten the wheel bolts in a cross pattern. It is not recommended to tighten the wheel bolts by pressing the key handle with your foot, as this may cause the key to break off and damage the wheel rim or cause injury.

11. Place the damaged wheel, tools and jack in the trunk.

Note It is recommended to check the tire pressure of the installed wheel at the first opportunity and, if necessary, adjust it.

https://vazweb.ru/desyatka/hodovaya/razboltovka.htmlhttps://pk-motors.ru/tyuning/razboltovka-kolesnyh-diskov-vaz-2110.htmlhttps://bolt-taxi.com/razboltovka-diskov- i-kolyos-na-vaz-2112-parametry-foto/https://carfrance.ru/kakaya-razboltovka-kolyos-na-vaz-2112/https://myducato.ru/vaz/razboltovka-na-vaz- 2112.html

Review of the best summer and winter tires

It is better to acquire separate sets of summer and winter tires in advance. Pirelli Cinturato P1 Verde tires are ideal for the warm season. Their cost is relatively high (from 3,500 rubles per 1 tire). However, they perform excellently on wet asphalt and are highly resistant to wear.

• Continental Conti Premium Contact 5 is well balanced. There are a large number of special drainage channels - they make it easy to drain water from the contact patch. This kit will cost slightly less than the one discussed above.
• Goodyear EfficientGrip Performance provides good grip and low fuel consumption. However, the tread thins out quite quickly - especially during intense driving. The rubber is soft and handles well. Despite its softness, it is difficult to damage it redder.
• Dunlop Sport BluResponse is relatively cheap compared to all the options discussed above. However, it has its weaknesses. For example, on wet asphalt the wheels slip a lot and handling deteriorates.

• Semperit Comfort-Life 2 is a rare guest on Russian territory. However, on dry asphalt at positive temperatures it performs more than well. However, rubber is distinguished by its noise.
• GOODYEAR 175/70R14 UG ICE ARCTIC D-STUD - studded tires at a relatively low cost. Regardless of the ambient temperature, it retains its flexibility and softness. Cost – from 4,000 rubles.
• HANKOOK 175/70R14 W429 is a more budget option. Cost – from 2,800 rubles. Thanks to the deep tread and flexible design, the driver can feel completely safe on the road.
• KUMHO 175/70R14 WI31 84T usually costs several hundred rubles cheaper than the modification discussed above. The presence of studs makes this tire safe on almost any road.

• VIATTI TIRES 175/70R14 BRINA NORDICO is manufactured using rubber mixing technology. Reinforced lugs make this model indispensable not only in winter, but also on dirt roads in summer.
• SAVA 175/70R14 ESKIMO ICE MS is the most profitable option. It has a relatively low price (from 2,000 rubles). There are no thorns. However, the deep tread and its shape provide high-quality, reliable contact with any surface.

Choosing suitable tires for the VAZ 2110 is a relatively simple process

However, it is important to familiarize yourself with the intricacies of tire selection in advance. Wheels that are too large can easily damage the vehicle body

Corrosion protection

For reliable operation of the chassis, everything is important: the bolt pattern, the dimensions of all components, the alignment/camber settings, and even the protection of the arches from corrosion. It is the arches that are more susceptible to adverse factors than other parts of the body - from ordinary moisture during rain to reagents on winter roads

To ensure reliable protection of the arches, it is best to install lockers (fender liners) on the VAZ 2110. Such protection will cost much less than subsequent repairs of rusted arches

It is important to choose the correct size of the lockers and ensure their tight fit in the area of ​​the arches

https://youtube.com/watch?v=o2FUAvK29RU

We hope that by completing all the repair work yourself, you will provide your VAZ 2110 with many years of trouble-free service on the road.

Self-adjustment

Next, you need to stand on a level surface and load the machine, as recommended by the manufacturer. That is, about 320 kg in the cabin and 40 kg in the trunk.

The first adjustment is to set the pitch angles of the turning axis. The second is camber, the third is toe.

In this case, the camber angle in the loaded state should be 0°30'+-30'. The toe-in should be within 0°15'+-10', and the pitch angles of the steering axes should be 0°20'+-30'.

Remember that camber and other wheel adjustments are necessary in all cases when you in any way interfere with the operation of the front suspension of the VAZ 2110.

Wheel alignment

After replacing wheel rims, the dimensions and bolt patterns of which differ from those provided for by the design of the VAZ 2110, it is necessary to make all the necessary adjustments in order to ensure reliable protection of the entire chassis, as well as tires and arches.

Correct alignment angles are required for each front wheel. There are three parameters that require correct installation: wheel toe, caster angles of the steering axles, and camber angles of each wheel.

Wheel installation options

The rules by which the parameters of the front wheel are set are as follows:

1. You won't go far if everything hangs out the way it wants, and the car is pulled to the side when it should be going straight. To ensure the stability of each front wheel, they are installed strictly at the required angles to the body and suspension elements. This is called the longitudinal inclination angles of the turning axis. Installation dimensions are indicated in the instruction manual;
2. Camber is the angle between the plane in which the wheel rotates and the vertical. The camber bolt helps install it (it secures the telescopic strut and steering knuckle). If the camber is installed incorrectly, the car “steals” and the tire tread wears out more on one side;

   Wheel installation options

3. The angle between the longitudinal axis of the car and the plane of rotation of the wheel is called toe. It is toe that is responsible for the controllability of the front wheel when cornering and at different speeds. If the toe is set incorrectly, there is severe lateral tire wear, tires squeal when cornering, and even increased fuel consumption.

Installing 4*100 disks

Let's consider several methods used by car craftsmen to install disks from foreign cars on a VAZ 2110:

1. Sometimes holes are drilled into the disc hub on a lathe so that it will be possible to install the discs you currently have. Both 98 and 100 bolt patterns are suitable. And if you need to replace the disk, then this is also not difficult to do. The bolt sizes are standard;
2. The simplest, but not the best way is to install the disk using extended bolts of regular diameter for wheels. But don’t be surprised later that this replacement led to the disc dangling, wheel play appearing, and it is impossible to establish the correct camber and toe, as well as the longitudinal inclination angles;
3. A popular, relatively safe method is to install standard size bolts with an eccentric on a VAZ 2110 (an option is also possible if the bolt has an offset center). Today, online stores offer many sets of such bolts;

   
   Wheel bolt with eccentric

4. Some people use special spacers. But in this case, the wheel offset will definitely increase by the width of the spacer. For safety, the width must be at least 20 mm. A compensating measure could be the installation of discs that have a short offset;

   
   Spacer mounted on the hub

   
   Spacers SS20 15mm

   
   OZ Racing spacer kit

   
   Spacers

   
   Spacers

   
   Spacers

5. The worst way is to install the disk not on 4, but on 3 extended bolts. What then can be the protection of wheels from “flying”, and road users from death in an accident? Never do this!

If you replace the standard wheels of a VAZ 2110 with those with a 4x100 bolt pattern, then when you gain speed you will find that the wheel dangles, and during sharp braking it may even fall off, and how this “adventure” will end is unknown.

Standard wheel sizes VAZ 2112 1.6i 16V 2112x

The VAZ 2112 1.6i 16V 2112x model was produced from 2004 to 2009. Table of standard and suitable wheel sizes for VAZ 2112 1.6i 16V 2112x.

Sizes of used disks:

5x13 ET35 PCD 4x98, 5.5x13 ET35 PCD 4x98, 5x14 ET35 PCD 4x98, 5.5x14 ET35 PCD 4x98, 6.0x14 ET35 PCD 4x98.

Important: the diameter of the central hole of the disk (DIA) of most modifications of the VAZ 2112 is 58.6 (mm)

Disclaimer: Although the data represents official manufacturer figures, the information above is for reference only and is not guaranteed to be completely accurate.

This is interesting: What is the bolt pattern on the Lada Vesta - wheel size

Calculation of parameters

To more accurately calculate the compatibility of different types of disks with different indicators and car models, there are special compatibility tables. To select the indicator correctly, the owner needs to know exactly the factory parameters.

Compatibility tables of various types contain information on most existing models (for VAZ cars there are tables certified by the manufacturer).

Finding such tables is not difficult; there are a lot of compatibility tables on the Internet. Here is an example for domestic cars.

The photo shows the wheel bolt pattern and compatibility table:

These tables indicate several important parameters:

• Disc offset
  (a specific parameter is individual for each model), it is indicated by the letters (ET);
• Bolt pattern
  - PCD. The parameter is common for VAZ cars and is adopted by a single standard for front-wheel drive families as 4/98. This index is relevant for the vast majority of cars of the AvtoVAZ family (with the exception of sports modifications (Kalina NFR, where wheels from French models are installed and the bolt pattern has different data);
• Disc diameter
  – DIA. This parameter indicates the permissible diameter value. On VAZ cars, the maximum value for most models is 14 inches, but for several models this value is 1 inch more. The maximum diameter for 14 inches is VAZ 2114, 2115, 2113, 2110, 2111, 2112, that is, a line of cars
• Serial production of which has been discontinued
  . The maximum value of 15 inches is typical for models - Kalina, Granta, Priora. For Vesta and Kalina NFR models, the maximum value is 16 and 17 inches, respectively.

On the video, the bolt pattern of the wheel rims:

Based on the value of the table for various models, the owner will be able to correlate the parameters of the new disk and the factory settings to select a product with the optimal value. In some cases, the diameter of the bolt pattern is slightly larger than the factory one.

In this case, special weights are hung on the disks to maintain optimal alignment. However, this method soon loses its effectiveness and the disc begins to mechanically interact with the hub, subsequently leading to breakdowns.

In the case of tables from AvtoVAZ, owners can trust the manufacturer’s data, since during the production and design process the model undergoes many tests, the main thing is that the table data be officially presented by the Tolyatti automaker.

The production of the domestic car Lada Priora was carried out from 2008 to 2022 inclusive. Over such a long time, the owners have redesigned some components of the car, the main ones of which are the wheels. At the moment, replacing discs is a common issue for most Lada Priora owners.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! This may be due not only to the visual component, but also to the technical one, since factory wheels on old Prioras tend to become outdated

This article will discuss the problem of replacing disks with both standard ones, which are installed by the manufacturer, and non-original ones, purchased for the purpose of tuning the car.

This may be due not only to the visual component, but also to the technical one, since factory wheels on old Prioras tend to become outdated. This article will discuss the problem of replacing disks with both standard ones, which are installed by the manufacturer, and non-original ones, purchased for the purpose of tuning a car.

Wheel selection rules

For the “ten”, the original wheels are 13- or 14-inch with a 4x98 bolt pattern, where 4 is the number of holes, 98 is the diameter of the circle on which they are located.

In fact, there is nothing complicated about it. It is not necessary to put your life in danger by installing discs with a drill even 1 mm more or less than permissible. Any wheels from Italian and some French cars are perfect for cars of the tenth family. Of course, with the same bolt pattern.

Here are just some of these cars:

• Ford Ka produced after 2009;
• Lancia Delta;
• Lancia Lybra;
• Lancia Musa;
• Lancia Ypsilon;
• Peugeot Bipper;
• Alfa Romeo 145, 146, MiTo;
• Citroen Nemo;
• a huge number of Fiat car models.

Table with bolt pattern 4x98.

It is worth noting that new VAZ cars have changed the Italian size to French. This happened with the arrival of the French B0 platform on the assembly line, on which Vesta, Largus, and Xray are built. Their disc drilling parameter is 4x100 mm. Select the right discs and do not forget about safety!

Features of wheel sizes for the most popular VAZ models

Among several dozen VAZ modifications, the most popular models over the entire 50 years were only 2 of them, as can be judged by the number of copies sold. The wheel sizes for these cars had the following parameters, which varied depending on the year of manufacture, technical equipment and equipment of the car:

VAZ is the latest modification of the “classic”, produced on the plant’s conveyors for 30 years: from 1982 to 2012. During this time, it never changed its appearance, and the disc bolt pattern was the same - 4x98 with a central hole diameter of 58.6 mm.

The width of the rim varied slightly depending on the model year.

If in 1982 the plant produced models with tire dimensions ranging from 5J to 5.5J, then at the end of production the concern increased the permissible size to 6J.

The radius of the wheels invariably varied from R13 to R15, which made it possible to alternate them by season, periodically changing the side profile of the tire, or immediately use all-season tires with a diameter of R14.

The VAZ 2107 tire size invariably consisted of only 3 main parameters - 175/70/R13, 185/60/R14 and 185/55/R15. The last of the listed parameters was actively in demand among lovers of fast driving on smooth city roads.

On a note.

As for the R13 rubber, it allowed the driver to feel as comfortable as possible when driving over rough terrain, as well as in winter, when the high cord profile took part in adhesion to the road surface. But the most popular parameter remained the universal size R14 and the largest number of tires were sold in this dimension.

If we look at the concern’s earlier cars, we can see that the wheelbase of the Zhiguli has remained virtually unchanged for more than 40 years. This leads to moral backwardness of the technical equipment of the plant's products. At the same time, the lack of new developments greatly reduces both the speed of release from the assembly line and the cost of engineering equipment, which leads to a very attractive retail price for the vehicle.

VAZ 2114. Produced in a smaller range - from 2001 to 2013. The car was just a restyled modification of the classic “nine”. The legacy of the outdated model did not affect the high popularity of this Lada, and all the wheels that were installed on hubs in the basic version had the same traditional bolt pattern 4x98, DIA 58.6 mm.

European standard bolt pattern 4x100 for Lada X-Ray

Like the bolt pattern of the VAZ 2114, the width of the wheel rims was not much different from the “seven” and fluctuated between 5J – 6J for the entire production period. As for radius, the concern has completely eliminated the 15-inch diameter from the factory equipment, without prohibiting drivers from installing this parameter as an option. The bolt pattern of VAZ 2114 wheels in the current size also made it possible to install standard 4x100 wheels in accordance with the sizes usual for Europe.

Not a single Lada model has ever looked aggressive; the hallmark of the product was practicality and reliability in operation. The concern did not use extreme overhang indicators, and the wheels were always hidden under the body arches. The average ET limit values ​​for both VAZ 2107 and 2114 were ET25...35 mm, and deviations from this characteristic obligated drivers to install additional mudguards on the side parts of the body and change the design of the hubs, making them more durable to avoid deformations.

The bolt pattern of the VAZ 2114 wheels, as well as all other dimensions of the hub and disks, were used on the brand’s followers - Kalina and Priora. With the arrival of new management at the domestic concern, this parameter ceased to exist altogether, since the plant had a new orientation to the West and possible import of products to the nearest CIS countries.

5 studs on VAZ 2121 wheels

14-inch wheels Kia Rio

It should be noted that the same options for using discs of different diameters are also implemented on crossovers. For example, on the previous generation Nissan X-Trail you can install 16-inch wheels, which is clearly evidenced by the re-rolling of this diameter. And the car came off the assembly line with 17- and then 18-inch wheels. Although there are known cases of using wheels up to 20 inches. Here, too, the only question is what do you want to get: a car that gravitates towards an SUV or a tough “sports barn”. The main thing is to know moderation in everything, because the engine and gearbox are not changed.

What has VAZ changed?

Now let's talk about how VAZ betrayed its size. Even on the progenitor of the first Zhiguli, the FIAT-124, the diameter of the circle on which the holes for the bolts were located was 98 mm. And since then, this size has been strictly observed on all VAZ cars, except Niva and Oka.

By the way, Italians are also faithful to traditions. For example, on the FIAT Albea, which was officially sold in Russia, it was possible to attach a wheel from a VAZ.

Tires for VAZ 2107

Tire and wheel sizes for Daewoo Nexia 2005

The safety of the car driver and his passengers depends even more on the characteristics and condition of the car’s tires. Their choice must be approached very carefully, and in no case should you skimp.

Types of tires by seasonal use

According to seasonal use, tires are divided into:

The first ones are made of soft rubber and have a special tread. At the same time, each manufacturer tries to increase the tread area, because the larger it is, the better the tire will perform on winter roads.

Summer tires are rougher, and their tread pattern is designed more for better grip on wet surfaces and drainage of water from the plane of contact between the tire and the road.

All-season tires are a generalized version of the first two types. If the “all-season” tire is really of high quality, then in winter it copes with its duties normally, but in the summer it is significantly inferior to summer tires in terms of the quality of grip on wet surfaces.

VAZ 2107 tire parameters

Like wheels, car tires have their own parameters. These include:

• profile width (the width of the tire itself, measured in millimeters);
• height (expressed as a percentage of the profile height to the width, measured as a percentage);
• landing diameter (determines the inner diameter of the tire, measured in inches);
• load capacity (indicates the maximum load per tire, measured in kgf);
• permissible speed value (indicates the estimated maximum permissible speed, measured in km/h).

VAZ 2107 leaves the assembly line of the plant shod with thirteen-inch radial tires with a profile width of 175 or 165 mm and a height of 70%. Standard tires are designed for 190 km/h and a load on one wheel not exceeding 470 kgf.

It is impossible not to mention the tire pressure, because the vehicle’s cross-country ability, its driving performance, and fuel consumption depend on it. The manufacturer of the VAZ 2107 recommends observing the following pressure indicators.

Table: recommended tire pressure for VAZ 2107

The choice between beauty and functionality of wheels should be based on how you use the car. If it is intended for city car rides, or participates in exhibitions of tuned cars, festive motorcades, then alloy wheels and low-profile tires are an ideal option. If the car is used daily in our off-road conditions for work, then it is better to install “stamping” on it with standard tires.

What is the bolt pattern on 7 4 by 98?

NEVER put hundred square meters in the wrong place. Better 98 zbs

0 0 Answer rating: 0

0 0 Answer rating: 0

Tire pressure VAZ 2107

The nominal tire pressure depends on the type of tire and the load on the vehicle. If the wheels are overinflated or low, the contact patch between the tire and the road changes. This causes deterioration in controllability and an increase in braking distance. In addition, uneven accelerated wear of the tread begins. Over-inflated tires increase wear on the center of the tire, while under-inflated tires increase wear on the edges.

It is recommended to check tire pressure after 500 km, but in practice it is better to do this more often. Small tire punctures, disc and spool defects cause air to escape from individual tires. In this case, the car may drift off course, especially when braking.

The nominal pressure in VAZ 2107 tires depends on the tire size:

• 165/80R13 - 1.6 for front, 1.9 for rear wheels;
• 175/70R13 - 1.7 for front, 2.0 for rear wheels.

In hot weather and when driving, tire pressure increases. With an aggressive driving style, taking sharp turns at high speed, the pressure can increase to 3-4 atmospheres. The tire material is designed for this and can withstand such changes. But if there is a hernia or cut on the tire, it may explode. A front tire explosion is especially dangerous, after which it is very difficult to keep the car on the road.

As pressure decreases, rolling resistance increases, which leads to increased fuel consumption. The tire also bends and the car becomes less responsive when maneuvering.

If the tire pressure is too low, the tires may even fall apart when cornering sharply.

Features of sidewalk parking

Since a catastrophic situation has arisen in cities due to a lack of parking spaces, municipal authorities allow cars to be parked on the sidewalks in certain situations. So-called sidewalk parking lots are formed, and two main conditions must apply here.

Firstly, these are specially designated places.

Secondly, such places must be marked with permitting signs. A “Parking” road sign is installed, as well as explanatory signs indicating how to install the machine.

Information on signs

Special signs may indicate the option of identifying a vehicle for parking.

1. On the road near the curb. The sidewalk runs parallel.
2. Full access to the sidewalk. The street is parallel.
3. Driving onto the sidewalk with the rear wheels or the front wheels.
4. Parallel to the roadway. You can drive onto the sidewalk with side wheels (any pair).
5. On the road surface. The front part is directed towards the road, the car is located perpendicular to the street.
6. Full access to the sidewalk. The car is positioned perpendicular to the movement, the front side is directed either towards the houses or towards the road.