Replacing the ignition switch and contact group on a VAZ 2108, VAZ 2109, VAZ 21099

Welcome! The ignition switch breaks quite rarely, but it still happens. After a lock breaks, it of course needs to be replaced with a new one, but how to do this, you ask? Some people still know the answer to this question, but some do not. For those who don’t know, we have prepared this article, which will describe in detail the process of replacing the ignition switch. And at the end of this article you will find a video clip that will describe in detail the process of replacing this lock. Note! To replace the ignition switch, you will need the following tools: First, you will need screwdrivers. When do you need to change the ignition switch and contact group? It must be replaced if it breaks, as well as if the key is lost, and even if the cylinder in the lock stops turning and is stuck in one place. The contact group must be replaced if it is deformed, and even if, after turning the key in the lock, the car’s engine stops starting.

Note! Before you immediately say that the contact group of the lock is to blame for everything, first check the contacts of its wire blocks for functionality. (How to check the contacts of the contact group, see below in the section: “Checking the contacts of the wire block”)

How to replace the ignition switch, check the contact group and replace it on a VAZ 2108-VAZ 21099?

Replacing the ignition switch:

Removal: 1) Starting with “The battery is a rechargeable battery,” unscrew the nut that holds the “-” terminal on the battery and then remove the terminal.

2) Then remove the steering column cover and both steering column switches.

Further, for clarity, the operation will be shown with the steering wheel removed, but you can still remove the ignition switch without removing the steering wheel.

3) Next, insert if the lock allows it, then insert the ignition key into it and put it in position “0”.

• Home
• Auto garage
• How to change the ignition switch on a VAZ 2109

Replacing the ignition switch and contact group on a VAZ 2108, VAZ 2109, VAZ 21099

Welcome! The ignition interlock breaks quite rarely, but it still happens. After breaking the lock, it must be replaced with a new one, but how do you ask? Some people still know the answer to this question, and some don't. For the ignorant people, we have simply prepared this article, which describes in detail the process of replacing the ignition. And at the end of this article you will find a video clip that details the progress of replacing this lock.

Ignition switch device VAZ 2109

ZZ is found in old and new designs. The old one has 4 positions, a long key and a relay. The new one does not have a relay, it has 3 positions and a short key.

The ignition switch of the VAZ 21099, like other models, performs two functions:

• mechanical – locks the steering wheel without a key;
• electrical - closes contacts depending on the position of the key.

ZZ car 2109

Scheme

The ignition switch diagram represents the position of the key in the lock and can be presented in the form of a table:

PURPOSE AND DEVICE

The main purpose of the lock was initially to protect the car from theft, however:

• Today, as can be seen from practice, in order to start and steal a car, car thieves do not necessarily need to have a key or a duplicate of it
• To put it more clearly, the protection from the castle used to justify itself, but today it is “so-so”
• Advanced car thieves, equipped with modern technologies and devices, are able to hack the electronic protection of the most modern anti-theft systems in just a few seconds.
• And on the VAZ 2109, the lock cylinder or the VAZ 2109 lock itself, or its domestic analogue can generally be called entertainment for beginners
• In fact, the ignition switch is an ordinary switch that, when you turn the key, opens or closes a certain group of contacts
• The appearance of a malfunction in the ignition switch increases the likelihood of vehicle theft several times, in addition, it creates great trouble for you and, according to the law of meanness, at a completely inappropriate moment for this
• The design of any ignition switch is similar; it consists of a lock and its contact group
• And the contact group consists of two separate plates, fixed and movable
• The movable plate moves when the key is turned in the lock and the contacts are closed in the required sequence
• Already now, switches that have the same design and order of contact closure are successfully used on all domestic cars

Reasons for replacement

As a rule, replacement of VAZ 2109 lock cylinders is carried out in the following cases:

• When they tried to steal a car and the lock cylinder was damaged in the process
• If the owner of the car has lost his keys
• Breakage of the larva during operation

The car engine may not start due to poor contact. It’s not at all difficult to check this; to do this, it’s enough to have an ohmmeter on hand, or a multitester with an ohmmeter function and five minutes of time:

• Disconnect the “-” terminal from the battery
• Remove the lower casing from the steering column

Removed the casing and opened the contacts

• Disconnect the contacts and check the resistance with an ohmmeter
• Serviceable contacts should have minimal (zero) resistance
• Otherwise, you need to replace either the contact group or the entire lock

We measure the contact resistance using an ohmmeter

Typical faults

Since the ignition switch on the VAZ 2109 performs two functions, the nature of the faults can be divided into mechanical and electrical, although most often the lock breaks down in starter mode:

1. A mechanical malfunction includes jamming of the core in any position: it is physically impossible to turn the key. In this case, you can inject a little silicone lubricant inside. If this does not help, you will have to remove the ignition switch and replace it with a new one.
2. Electrical faults can occur at a certain position of the key when the integrity of the electrical network in the switch is broken. If there is no contact, all system components will not work. If there is contact, but the circuit does not occur where it is needed, this is fraught with a short circuit and overheating of the circuit breaker. It may melt and a specific smell will appear (video author - MAQS MAC).

What is

First, let's look at the structure of the castle. Let's find out what it looks like, what it consists of, what its operating principle is, and so on:

• As mentioned, the ignition switch is a very important element of the VAZ 2109 car, because almost all available equipment is connected to it.

Note. Although there are components that do not depend on the lock in any way. Here they are: license plate lights, brake lights, parking lights, hazard lights, interior lights and lights on the dashboard.

• There are different types of ignition switches: new or old type. The first version without a relay has three positions and a short key, the second with a relay has four positions and a long key.

Scheme

Below is a typical diagram of the ignition switch on the “nine”.

Video “Replacing ZZ”

This video demonstrates the repair of the ignition switch of a VAZ 2109 (the author of the video is Vitaly Rau).

Schematic electrical diagrams, connecting devices and pinouts of connectors

The ignition switch in cars of the VAZ family fails from time to time due to weakening of the contact posts or burning of the contacts inside it. It also happens that the cams of a plastic roller are produced. You can disassemble the lock and clean it, but it’s better to just replace it with a new one, considering that it costs pennies compared to imported locks.

But if connecting the wires together did not result in the starter operating (or it did not turn on the first time), check the solenoid relay on the starter. The contact spots on it may also burn out, which will prevent the circuit from closing normally. Alternatively, you can use a screwdriver to short-circuit the two large terminals on the solenoid relay (before doing this, put the car in neutral and use the handbrake). When closed, the starter should begin to spin vigorously. If this happens, remove and change the solenoid relay. If the starter rotates “sluggishly” when it closes, you will have to remove it and check the condition of the brushes.

All operations are performed with your own hands, without the help of car service specialists. Moreover, the price of an ignition switch on a VAZ2106 is up to 100 rubles. To replace it, you will need to know the pinout of the wires coming from it, for which the editors of the site 2 Schemes.ru have prepared a large reference material.

The ignition switch is designed not only to start the engine - it performs several functions at once:

1. supplies voltage to the vehicle’s on-board network, closing the circuits of the ignition system, lighting, sound alarm, additional devices and instruments;
2. at the driver’s command, turns on the starter to start the power plant and turns it off;
3. turns off the power to the on-board circuit, preserving the battery charge;
4. protects the car from theft by fixing the steering shaft.

Repair and replacement instructions

Basically, the protection zone can be repaired. Repair usually consists of replacing the core or contact group. If the problem remains after repair, then the ignition switch needs to be replaced.

Core of ZZ VAZ 2109

On a VAZ 2109, replacing the core consists of the following steps:

1. First, the protective and decorative cover is removed from the steering column, as well as the windshield washer and turn switches.
2. The lock is secured with screws and a hook latch. There may be problems with unscrewing the screws, since their heads are cut off. To remove them, you first need to loosen them with chisels and then unscrew them with pliers. You can carefully drill out the screws.
3. Next, we disconnect the clamps, disengaging them.
4. By pulling out the side pin, you can remove the core. If that doesn’t work, the core can be drilled out using a thin drill. In extreme cases, you will have to dismantle the entire assembly.
5. The next step is to disconnect the connector, wire plug, and ground wire.
6. By releasing the latch, you can remove the cover and contact group.
7. We insert a new core and check the work. When you turn the key, all processes should work.

The steering wheel lock should also be checked. If the steering wheel does not lock when turned fully, you need to adjust the position of the lock on the column.

Contact group ZZ

Replacing the contact group of the VAZ ignition switch comes down to dismantling the ignition switch: the removal diagram is described above.

When performing the procedure, the following recommendations should be followed:

• before disconnecting contacts, it is advisable to assign numbers to them, this will help to avoid errors when connecting;
• If there is a retaining ring in the design of the contact group, you must first remove it using an awl.

Knowing how the ignition switch on a VAZ 2109 works, and having at least a little experience, you can carry out the repair yourself without resorting to the help of specialists. This way you can save on maintenance costs.

Pinout of the ignition switch VAZ-2101 - VAZ-2107

The ignition switch on these cars is located to the left of the steering column. It is fixed directly to it using two fixing bolts. The entire mechanism of the device, except for the upper part in which the keyhole is located, is hidden by a plastic casing.

On the visible part of the ignition switch housing, special marks are applied in a certain order, allowing inexperienced drivers to navigate the lock activation mode when the key is in the hole:

• “ ” – a mark indicating that all systems, devices and instruments that are turned on using the lock are turned off (this does not include the cigarette lighter, interior lighting, brake light, and in some cases the radio);
• “ I ” is a mark informing that the vehicle’s on-board network is powered from the battery. In this position, the key is fixed independently, and electricity is supplied to the ignition system, to the electric motors of the heater and windshield washer, instrumentation, headlights and light signaling;
• “ II ” – engine start mark. It indicates that voltage is applied to the starter. The key does not lock in this position. If you release it, it will return to the "I" position. This is done so as not to subject the starter to unnecessary loads;
• “ III ” – parking mark. If you remove the key from the ignition in this position, the steering column will be locked with a latch. It can only be unlocked by inserting the key back and turning it to position “0” or “I”.

Preparation

At the preparation stage, you will need to collect the necessary tools near you, which will be useful in the process of dismantling and installing a new ignition switch. You will also have to remove the steering cover and steering column shifters. Doing this is quite difficult, but we will tell you step by step about all the nuances of these preparatory activities. So you can easily figure out for yourself how to remove the ignition switch on a VAZ 2114.

Tools you will need:

• Phillips strong screwdriver;
• Open-end wrench 10 millimeters;
• Chisel;
• Hammer;
• Pliers or pliers;
• New ignition switch assembly;
• Lock mounting screws (4 pieces).

Now let's move on to the casing and switches. For more convenient work, many advise removing the steering column switches and the steering wheel itself. Dismantling the casing is performed in the following sequence:

1. Disconnect the negative cable from the battery. Nobody has yet canceled the requirements for personal safety and protection against electric shocks;
2. Unscrew the three screws securing the two parts of the casing. A screwdriver is useful for this;
3. Unscrew the screw that connects the housing to the connector of the steering column switches;
4. Remove the two screws that hold the lower housing to the steering column;
5. The lever that fixes the column at the corner leads down;
6. The steering wheel also goes down;
7. The lower casing is then removed;
8. The power supply from the emergency lights must be disconnected;
9. Now you can remove the top casing;
10. To dismantle the steering column switches, you need to act one by one;
11. Simultaneously press both latches and thereby remove the elements from their seats;
12. Disconnect them from the power supply.

Pinout of lock VAZ-2108, VAZ-2109, VAZ-21099

Pinout according to the old type

Pinout of the VAZ-2109 ignition switch with unloading relay:

1. comes +12V in position I, II, III (parking)
2. comes +12V in position I, II, III (parking)
3. comes +12V in position III (parking)
4. position I, +12V goes out after turning on the ignition (contact 15/2), disappears at start (II);
5. position I, +12V goes to the starter (pin 50);
6. position I, +12V goes away after turning on the ignition (pin 15), does not disappear when starting II;
7. +12V comes from the battery (pin 30);
8. comes +12V constantly.

New pinout type

Pinout of the new VAZ-2109 ignition switch:

1. comes +12V constantly
2. comes +12V constantly
3. +12V arrives after turning on the ignition (pin 15), does not disappear when starting II;
4. +12V arrives after turning on the ignition (contact 15/2), disappears at start (II);
5. position I, +12V goes to the starter (pin 50);
6. +12V arrives after turning on the ignition (pin 15), does not disappear when starting II;
7. +12V comes from the battery (pin 30);
8. comes +12V constantly.

Power-up modes used

Lada 2105 Bright White 15 R Logbook Installation of steering column switches for a Chevrolet Niva ignition switch for a VAZ 2110
At each of the turns, the connection of certain devices is provided. There are markings in a circle in front of the socket indicating the position to which a certain mode corresponds.

Null

To activate this mode, just insert the key into the “secret”. In this case, devices that are directly connected to the battery remain active.

Additional consumers will be put into operation after the larva is rotated at a certain angle. Voltage is supplied to pins 30/1 and 30.

The first is “ignition”

In the first position, the driver can turn on the front lighting, such as the low and high headlights. The tidy and interior light up responsively. The connection diagram for the VAZ-2109 ignition switch is activated during this turn, releasing current to the 30–INT pair.

When there is a connection between terminals 30/1 and 15/1, the rear lights, reversing lights, turn signals are operational, and the generator excitation winding is energized. The XX solenoid valve also receives power.

In this position, contacts 30/1 and 15/2 are closed, which ensures the operation of, in addition to the head light optics, the functioning of the fog lights, the rear window wiper and its heating. The headlight cleaners, heater fan and engine cooling system propeller are connected to this contact.

The second is the “starter”

By moving the key to the current position, the driver does not block the connection of electrical consumers that were started in the previous “ignition” position. This fully applies to both the closed contacts of the pair 30/1 - 15/1, and to the pair 30 - INT.

The main change that the VAZ-2109 ignition switch connection diagram provides in such a situation is the activation of a pair of contacts 30–50. This allows the starter to start.

Third – “parking”

At this angle of rotation, consumers started in the “ignition” position and closed contacts 30 – INT remain activated. A closed pair 30/1 - P is also added. It is responsible for the parking lighting.

Pinout of lock VAZ-2110, VAZ-2111, VAZ-2112

Pinout of the ignition switch VAZ-2110:

1. comes +12V for the microphone of the sensor of the inserted key;
2. the mass comes when the driver's door is open;
3. +12V goes to the starter (pin 50);
4. +12V goes out after turning on the ignition (pin 15);
5. +12V goes out when the key is inserted to pin 5 of the BSK;
6. comes +12V to illuminate the lock cylinder;
7. +12V comes from the battery (pin 30);
8. not used.

Installing a new device

Now you can finally proceed directly to replacing the broken or worn out ignition switch on your VAZ2114 car.

Removing the ignition switch

To do this, follow the following sequence of actions:

• Insert the key into the new lock and turn it to the first position. This will allow the latch, which is responsible for locking the steering shaft, to hide inside the housing structure;
• Insert the lock into place following the reverse dismantling sequence;
• Install the four retaining bolts and tighten them slightly.

Pinout of lock VAZ-2113, VAZ-2114, VAZ-2115

Pinout of the ignition switch VAZ-2113, 2114, 2115:

1. comes +12V for the microphone of the sensor of the inserted key;
2. the mass comes when the driver's door is open;
3. +12V goes to the starter (pin 50);
4. +12V goes out after turning on the ignition (pin 15);
5. +12V goes out when the key is inserted to pin 5 of the BSK;
6. comes +12V to illuminate the lock cylinder;
7. +12V comes from the battery (pin 30);
8. not used.

Exactly three switched contacts

One line through which current is supplied, and only one ignition circuit - this solution is typical for all VAZ cars, if we talk about the “2110”, “2170” and later families. Even in Grants, produced since 2012, the additional ignition circuit did not appear. In general, with the transition to the “Ten” family, three “significant” terminals of the lock remained:

• Contact "30";
• Terminal “15” (can be designated as “15/1”);
• Terminal "50".

The ignition switch circuit looks trivial, even if we talk about the Lada 2110.

Ten and its switch , diagram Diagram and connector of the ignition switch of modern models Ignition switch connector Tens

REPLACING THE IGNITION SWITCH OF A VAZ 2109

The Tens connector has 8 terminals. And in “Priora”, as well as in “Granta” and “Kalina” this number is reduced to three

Of the 8 terminals available in the VAZ-2110 connector, the 7th and 8th simply duplicate each other. Two more are connected to the button, and another pair of terminals are connected to the lamp.

The lock connector of all VAZ models, starting from “2170”, is equipped with only three contact terminals. And the additional connector, which is equipped with a pair of terminals, is connected to the immobilizer in these cars.

The “3” mark has disappeared from the “Tens” lock cylinder. And until now, VAZ produces just such locks, where the key can be installed in one of the following positions:

The presence of the “Parking” mode, as you can see, is not provided here.

Sources:

https://granta-service.ru/remont/zamena-zamka-zazhiganiya-vaz-2109-karbyurator-inzhektor-poshagovaya-videoinsttruktsiya.html https://aforizmus.ru/raspinovka-zamka-zazigania-vaz-2109/

The structure of a car ignition switch

1. Locking rod
2. Frame
3. Roller
4. Contact disc
5. Contact sleeve
6. Block
7. Protrusion of the contact part.

The lock mechanism is connected to many wires. They continue from the battery, connecting all the electrical devices of the car into a single chain. When you turn the ignition key, the electrical circuit is closed from the “-” terminal of the battery to the ignition coil. As a result, the current passes through the wires to the ignition switch, through its contacts it is directed to the induction coil, after which it returns back to the “+” terminal. As electricity passes through the coil, it generates high voltage, which it transmits to the spark plug. Therefore, the key closes the contacts of the ignition circuit, thereby starting the car engine.

Removing the lock

In order to provide access to the lock, you just need to remove the steering column cover. The lock has a fastening in the form of a clamp or stepladder. The removable plate covers the steering column and is attached to the lock body with two or four screws with “breakaway” heads. In order to loosen them, you can use a thin chisel:

All that remains is to disconnect the wires and remove the lock. In the photo, the steering wheel and steering column switch have been removed, but there is no need to do this - it’s just that the image is more clear.

Replacing the ignition switch on a VAZ car

To carry out repair work to replace the ignition switch of a vase, we will need: a screwdriver, a tester and a thin awl. Once you have everything you need, you can begin the repair. On all classic VAZ cars, the ignition switch is located at the bottom, on the left of the steering column. To replace you need:

1. Disconnect battery
2. Remove the plastic casing by first unscrewing the screws that secure it.
3. Then unscrew the two screws securing the ignition switch to the bracket.
4. We insert the key and set it to position 0 to disable the anti-theft device.
5. Insert the awl into the hole in the bracket and press the latch. Then we take out the lock itself.
6. After removal, it is recommended to mark the contact wires so that nothing is mixed up the next time you connect.

Changing the contact group

From a cost point of view, replacing one contact group is the least expensive:

• All our actions are repeated in principle, as in the case described above with removing the lock, you will have to remove the casing, and so on
• To avoid the common nuisance associated with mixing up contacts, it is recommended to number them (or otherwise mark them) before disconnecting them.
• This measure will save your nerves and time
• Some models of locks have a locking ring in their contact group, and here we need an awl to remove it
• It’s important not to forget to put it back in place later.
• Then everything is assembled back and screwed to the steering column

That's all, all that remains is to finish watching the video and calmly change any part of the lock.