Lada Granta how to remove front and rear door trim

Published: 10/30/2020

Replacing the front or driver's door trim
HOW TO REMOVE THE COVER. VAZ 2114
Removing the trunk lock drive
Removing the rear door trim
How to remove the door trim on a Lada Granta
Removing the rear door interior handle
Front door diagram. Catalog numbers of parts
Replacing the front door trim
How to remove the front driver's door trim on a Lada Granta
How to remove the door trim of a Lada Priora yourself
Remove the front door trim of the Lada Granta
Removing door trim on Grant
Removing the front door trim of the Lada Granta
Replacing the bearing of the input shaft of the VAZ 2107 gearbox

Replacing the front or driver's door trim

To remove the door trim on a Lada Grant, you need to remember the location of the screws that hold it in place. There are five of them in total:

under the lock button;
in the armrest;
immediately under the armrest;
two from the bottom of the panel.

They are not difficult to find. Next we proceed to dismantling:

We unscrew the door lock button, pick up the plug and unscrew the screw.
We unscrew the screw in the armrest from above (in the pocket) and from below.
Same with the two on the bottom of the trim.
We pry up the upholstery with a screwdriver to pull it off the rear view mirror adjustment knob.
We pry up the upholstery and slowly (so as not to break it) remove it from the clips (8 in total). We recommend starting this from the bottom right corner.
The last step is to turn off the electronics (if you have speakers or power windows).

This completes the dismantling. To install a new panel, follow these steps in reverse order.

HOW TO REMOVE THE COVER. VAZ 2114

Removing the casing

front door

. Vkontakte community. Subscribe! Xiaomi Redmi Note 3 Pro.

4) Also, usually there is a speaker, it is attached to 2.4 bolts, to be honest I have seen one. Unscrew, there are cross-shaped bolts from the factory. We are deleting.

5) At the top we twist the locking “bolt”, it just turns like a bolt.

6) All removed, now we need to separate the cover, this is a little more difficult. You can pull the corners out and you can pick up the screwdriver and pull yourself out. The main thing is not to break, carefully trying to separate. If some rivets are broken (and it will be 100%), don't worry, we bought new ones

This “analysis” concludes, as you can see, nothing complicated, and they still believe that the front part is complex. Watch video.

Everything is much simpler behind.

Removing the trunk lock drive

To remove the lock drive, you need to disconnect the lock rod from the drive (see above)

Using a marker or felt-tip pen, outline the position of the lock drive relative to the trunk lid

Using a wrench or a socket 8, unscrew the two nuts securing the lock drive to the trunk lid

Removing the lock drive

Use a screwdriver to pry it off and remove the retaining ring.

Removing the pressure lever

And remove the fixing plate

Remove the pusher with washer and spring

We take out the cylinder lock mechanism

Removing the rear door trim

The process of removing the trim from the rear door of the Lada Granta is somewhat complicated. Additional handle fastenings are installed to close the door. It is attached to the car body using two “10” bolts.

Carefully pry off the plastic cover of the door handle. It is better to do this with a polymer material, a plastic card. It is strictly forbidden to use metal objects, as the edge will be damaged.
Using a Phillips screwdriver, unscrew the two bolts securing the handle and remove it.
We twist the latch flag.
Unfasten the plastic clips around the perimeter of the card.
In the cavity of the opening, we disconnect the blocks with wires that go to the speaker.
We replace the door card, carry out preventative maintenance, and connect the electrical wiring. We install new auxiliary equipment as necessary.
The assembly of the structure is carried out in the reverse order.

By analogy, we remove the trim from the rear door on the opposite side.

LEATHER INTERIOR ELEMENTS for Lada cars at the best price

Leather interior elements (gear shift knobs, handbrake handles, interior door handles, edgings, armrests and covers) with different stitching variations of your choice.

All elements are made of high-quality eco-leather and blend perfectly with the interior of Lada Granta, Kalina-2, Priora, Datsun, Vesta, Xray, Largus cars.

Central glove box for Lada Kalina-2 and Granta FL, covered in leather. Material – auto eco..

Inserts (liners) in door cards for Lada Granta, Kalina-2 and Datsun cars. Material – leather..

How to remove the door trim on a Lada Granta

It came to covering the rear roof pillars, unfasten the back of the rear seat and lower it for convenience, then unscrew one screw.

We also place our fingers under the upper part of the casing and pull it towards ourselves.

This is what we have, under the plastic

We do the same on the other side, and for the convenience of removing the trim, we pull off the rubber bands of the doors where required.

Next is the most interesting thing, I won’t show the location of the ceiling lining pistons, they can’t be seen with the naked eye anyway, but you can remove them in different ways, one way carefully and the other barbarously, we choose the middle one, since for such providential work there is no necessary tool and there is no way to buy it washed off for one-time use, used the material at hand, what was lying badly, used an old smear from a Chinese toner...

I cut it by eye.

We insert it between the piston and the trim, and pull it towards ourselves without damaging the ceiling trim.

something like this.)))

The casing is intact

And so we continue until there are 8 pistons in our hands, and here it is, although I couldn’t take a photo of myself as I pull out the headliner, it is pulled out through any rear door, having first lowered the front seat of the side through which you would drag the trim, I pulled it out through the back left.)

And this is what we have

Well, so to speak, to get the full picture, I removed the trim of the rear shelf, it is held on by three pistons.

Recommendations

Comments 81

I want to tighten it the same way. Tell me, how did you make the reddish line? I can’t figure out how to guess the location of the line?

How much does this beauty cost? Is it possible to order it for you? Don’t you think it would be more attractive if the leather was blacker in color?

not cheap! but great! It’s a pity you don’t have any patterns! and in Surovoe they do both the ceiling and the racks, it costs 15,000

If I had something, I would gladly make it myself. Leather, glue, threads, tape, marker, knife, hands, brain (the central part of the nervous system of animals, usually located in the head of the body and representing a compact accumulation of nerve cells and their processes)

, time.

that's right my congratulations! It’s not bad, I’ll tell you! beautiful!

Maybe you can find a pattern)))

There is not. they were thrown away, look in the post above, I noted where the seams are, I think it won’t be very difficult to create them yourself))

Pass! Template in PM))))

Pattern no, I sent a couple of photos to the group, take a look

The view is rubbish! definitely cover the pillars, but think about the roof, it’s quite a pain, but if someone does it then literally YES! WORLD!