Error P0343 - Step-by-Step Diagnosis and Repair Guide

What does code P0343 mean?

P0343 is triggered when the engine control module (ECU) receives a faulty signal from the camshaft position sensor (CPS).

A common cause is a faulty camshaft sensor or damaged wiring. The DPRV is installed on one of the camshafts. P0343 is a common trouble code that has been used by all automakers since approximately 2000.

Some engines have multiple camshaft position sensors. Since the camshaft must be in sync with the crankshaft sensor when starting, a common symptom is that the engine will be hard to start or not start at all.

The four-stroke crankshaft rotates two revolutions per cycle, and the camshafts rotate one revolution per cycle. Older cars usually do not have a camshaft sensor, but only a crankshaft sensor. This is because older cars don't need to know what RPM the crankshaft is at.

Each cylinder is supplied with ignition and fuel once every two revolutions of the crankshaft. To do this, the DPRV is used to determine whether the cylinder is in the intake or combustion cycle.

In older cars without a camshaft sensor, the spark plugs fire twice per revolution, this is called "wasted spark." Thus, to avoid firing the ignition coils twice per revolution when only one is required, a camshaft sensor is used.

Symptoms of malfunction

The main driver symptom of P0343 is the MIL (Malfunction Indicator Light). It is also called Check engine or simply “check light”.

They can also appear as:

1. The “Check engine” warning light on the control panel will light up (the code will be stored in the ECM memory as a malfunction).
2. Decrease in engine power.
3. Possible misfires in the engine cylinders. The car engine may also become unstable.
4. Floating speed, as well as attempts to stall at idle.
5. The engine stalls or has trouble starting.
6. Increased fuel consumption.

The vehicle will most likely run with trouble code P0343. But it may be difficult to start, and there may also be a drop in power and unstable engine operation. To avoid damage to other engine components, if this code is detected, it is recommended that the problem be repaired as soon as possible.

SYMPTOMS AND INSPECTION

Signs of a malfunctioning camshaft sensor, by which you can determine that the device has failed, are as follows:

• Increased fuel consumption;
• Problems in the vehicle self-diagnosis mode;
• Reduced acceleration dynamics;
• The “Check Engine” sign or errors 0343 or 0340 appear on the dashboard.

The “Check Engine” icon, as a rule, lights up when the DF is completely out of order. The following happens: you turn on the ignition, after which the starter starts working, at this time the ECU unit should receive a signal from the sensor, but since the DF is broken, it is not there, and the electronic control switches the engine to twin injection mode (based solely on the data received from the DKPV ), turning off the phased injection of the fuel mixture.

If you find any signs of malfunction, you need to check the DF. You can do this yourself; you only need a tester (multimeter), which can be purchased at any car store for 400-600 rubles. The device is inexpensive, but useful - you will need it several times when diagnosing a car.

On fourteenths with a 16-valve engine, DF models 21120-3706040 are installed, on 8-valve engines - 21110-3706040. Checking each of them has some features.

Scheme (for 8th grade)

1. On the multimeter probe (V1 mode), which will be connected to contact “E” on the sensor, set the voltage to 13.5 V, on the second probe (connect to contact “B”) - 0.9 V;
2. We close the probes on the corresponding contacts. We bring a metal plate to the end part of the DF (a screwdriver will do). If the device is working normally, the multimeter will show that the voltage at pin “B” has dropped to 0.4 V (should return to 0.9 when the plate is removed). Differences in readings – the sensor needs to be replaced.

Checking the DF of a 16-valve engine:

Scheme (for 16 cells)

1. We switch the tester to V2 mode. On the probe of contact “E” we set the voltage to 13.5 V, on contact “B” - 0.4 V;
2. Insert a screwdriver into the hole at the end of the DF housing. When the sensor is working, the voltage at contact “B” will increase to 0.9 W and drop back if the screwdriver is removed.

How to get rid of error p0340

Methods for getting rid of malfunctions that caused the formation of error p0340 (malfunction in the camshaft position sensor circuit) depend on the causes of their occurrence, as well as the specific car model - for example, Nissan, Ford, Chevrolet, Opel, Toyota. , VAZ (in particular, VAZ 2114). However, the general verification algorithm will be as follows:

1. Using an error scanner, check the ECU memory for errors p0340 and possible others. If only one error is detected (or related ones, for example, p0342, p0343), then you should try to reset, as indicated above. That is, remove them using software or by disconnecting the negative terminal of the battery for 10...20 seconds. If the error disappears after starting the engine, it means that it was a false response of the sensor or ECU. If the error occurs again (you should read the error number again with the scanner), then you need to continue further diagnostics and repairs.
2. Check the latch, which ensures rigid contact between the chip and the sensor body. In some situations, it can be broken off, and this leads to loss of contact between all or individual wires and contacts on the sensor.
3. Check the quality of installation of the sensor in its mounting location. In particular, check the tightening torque of the nut (usually the sensor is secured using a bolt with a nut with a diameter of 10 mm or similar, depending on the specific engine). Make sure that the engine has the correct sensor for this particular motor. In particular, not only in terms of fastening, but also in model, since sensors may differ in both geometric shape and size, and because of this, the sensitive element of the sensor will not detect the passage of a rapper near it, which will lead to the absence of corresponding signals on the ECU. If the sensor is not suitable, you need to buy a new camshaft sensor and replace it.
4. Visually check the condition of the contacts and terminals in the electrical circuit for connecting the camshaft sensor. In some cases, oxidation (rust) occurs on critical terminals, which leads to a decrease in the quality of contact. This is due to exposure to moisture and/or simply old age. If oxides are detected, you must get rid of them by thoroughly wiping the contacts. To clean difficult stains, you can use special electrical contact cleaners.
5. Using a multimeter in continuity mode or measuring insulation resistance, you need to verify the integrity of the wires coming from the computer to the camshaft sensor. Usually there are three wires. In addition to checking the integrity of the wires, it is also necessary to check the insulation resistance value in pairs between them, as well as between each of the wires and the machine body (“ground”). However, in the latter case, the ground wire will “ring” with the body. Moreover, in the process of the described test, the multimeter probes must be placed on the contacts of the corresponding connectors.

VAZ 2114: error 0343 - causes, symptoms, solutions

Error P0343 for VAZ 2114 (8 valves) indicates a malfunction of the camshaft position sensor. It indicates that this sensor emits a very high signal level that is not provided for by the automaker. This means that there is increased voltage in its circuit.

The sensor is connected to the camshaft, or more precisely, to its rotating part. When the position of the element changes, the gaps and the magnetic field change. Therefore, the tension may also become different.

Diagnosis and problem solving

First of all, you need to read all stored error codes using an OBD-II scanner. If there are no other faults, proceed to troubleshooting P0343.

It is necessary to check the wires, connectors and other electrical components of the system. If any defects are found, eliminate them. After this, you need to clear the error codes from the PCM memory again and recheck the system.

If the error code appears again, check the battery charge and also inspect the starter motor. Troubleshoot, then clear the PCM memory again and check the system to see if P0343 appears again.

This procedure must be performed every time after repair work is performed. This will help determine if the problem is resolved.

Check the camshaft sensor itself if you need to replace it. In most cases, these steps will help fix your vehicle's problem.

On which cars is this problem most common?

The problem with code P0343 can occur on different machines, but there are always statistics on which brands this error occurs more often. Here is a list of some of them:

• Audi (Audi a4, Audi TT)
• BMW
• Cadillac (Cadillac SRX)
• Chery (Chery Amulet, Jagi, M11, Tiggo)
• Chevrolet (Chevrolet Avalanche, Aveo, Lacetti, Traverse)
• Chrysler
• Citroen (Citroen C4)
• Dodge (Dodge Ram)
• Ford
• Geely (Geely MK)
• Hyundai (Hyundai Accent)
• Kia (Kia Rio, Sportage)
• Lexus
• Mercedes
• Opel (Opel Corsa)
• Peugeot (Peugeot 308)
• Skoda (Skoda Octavia)
• Toyota (Toyota Camry)
• Volkswagen (VW Beatle, Jetta, Passat, Tiguan)
• VAZ 2110, 2111, 2112, 2114, 2115
• Volga Chrysler, 31105
• Gazelle Chrysler, 405
• Lada Vesta, Granta, Kalina, Largus, Niva, Priora
• UAZ Patriot

With fault code P0343, you can sometimes encounter other errors. The most common are: P0030, P0036, P0124, P0332, P0335, P0336, P0340, P0341, P0342, P0345, P0346, P0347, P0348, P0349, P0365, P0366, P0367, P0368, P0369, P039 0, P0391, P0392, P0393 , P0394, P0606, P2122, P2138.

How to run diagnostics?

Press the daily mileage reset button and hold it. Turn on the ignition and release the button.

The arrows on the dashboard start moving - this is the entry into the mode. Press the button briefly twice and it will display an error code.

As follows:

Nothing is clear, but there is a special table that deciphers these codes. It looks like this.

Sometimes it happens that the code we need is not in the table. This is fine. If the figure is not the same as in the table, then this means the presence of two malfunctions at the same time. For example, code 6 means the simultaneous presence of codes 2 and 4. And code 10 means errors 2 and 8.

All other error codes are deciphered in the same way. True, this system is quite primitive. Normal diagnostic tools have more detailed information about faults. The codes would look, for example, like this:

“P0303” - 03 means misfire, and the second 03 is the cylinder number. That is, the engine is tripping.

Error codes on the dashboard provide little information. It is much better to use special diagnostic equipment. Even the cheapest one can scan almost all Chevrolet Niva engine errors.

It may happen that an unknown combination of numbers and symbols appears on the dashboard, this indicates that the on-board computer is warning you that there are certain malfunctions in the car, and in order to correctly decipher the error codes on the Niva Chevrolet car and make the necessary repairs, you need to know what this or that information warns about. This article will help you with this, as in it we will look in detail at what different combinations of numbers mean and how to correct them.

But before we look at what errors there may be, let’s figure out how to detect and decipher them in general. In order to do this, you must first of all diagnose the car itself, since you can’t do without it. One of the simplest diagnostic methods is the information that appears on the dashboard, but in addition to numbers, certain phrases can also be displayed, but the car owner cannot always understand the translation of this message.

To find out in more detail about the causes of a breakdown on a Niva Chevrolet car, you can use a special scanner. It is a laptop computer with special software installed, thanks to which self-diagnosis occurs without any problems.

Now let's take a closer look at what errors can appear in the Chevrolet Niva SUV and what they mean.

Troubleshooting table for P0343

ErrorDescription Causes Remedy

Recommended Tools to Fix P0343

• To read fault codes - FOXWELL NT301. For advanced troubleshooting, you may need a more advanced scanner.
• Car charger: with battery repair function or simple.
• To check the integrity of the wiring and sensor, use a regular digital multimeter or a more expensive device.
• For an extended check of the signal from the camshaft sensor, use an oscilloscope.

Previous post Error P0300 - what it means, symptoms, causes, diagnosis, elimination

Next entry AlfaOBD diagnostics Fiat Group

How to replace a phase sensor with your own hands

If you are absolutely sure that the phase sensor is faulty, you can replace it yourself. It is located at the end of the cylinder head next to the air filter.

Replacing the phase sensor begins by disconnecting the power from the battery. In this case, the control unit memory will be reset.

If this is not done, it will continue to operate in the same mode as with a faulty phase sensor. Normal operation will begin after a few engine starts.

The tool that will be needed is just a ten key and sealant. Next, disconnect the wires from the phase sensor and remove it using a key.

The new sensor needs to be coated with sealant, the layer should be small, and it should be left for about five minutes before installation. We install it on the seat and connect the wires.

Next, connect the battery, start the engine and see if the check engine light comes on. If it no longer lights up, then the sensor is installed correctly.

What are the errors that determine the malfunction of this mechanism?

Error code - 0340

A fairly common phenomenon occurs when the “meat grinder” on the dashboard (check engine) lights up. This process appears like this: when starting the engine, the starter works for several seconds, and then phase sensor error 0340 is displayed. The thing is that when starting the car, the electronic unit The engine control waits for a certain signal from the phase sensor. If it is absent, the control unit does not send an impulse to the ignition system and fuel supply system. Consequently, the engine does not start, and the engine control lamp comes on, indicating “error 0340” on the VAZ 2114. You can diagnose the breakdown using the car’s on-board computer, or contact a specialized service center.

Check engine error on VAZ 2114

Symptoms of this problem:

Working principle of the camshaft position sensor

There are three types of DPRV:

• Magnetic (inductive type). The principle of operation is based on the passage of a metal object (tooth) in a constant magnetic field. Magnetic sensors usually have two terminals.
• Based on the Hall effect. Records changes in the magnetic field around the sensor. Such sensors usually have three terminals.
• Optical. The principle of operation is based on recording the reception and interruption by a photocell of a beam of light emitted by a source.

The most common DPRVs are of the first two types. Optical ones are used only in some brands of cars (for example, cars based on the Mazda GE platform). Some car models may have two or more sensors installed. And perhaps of different types.

Integral sensor

Hall effect sensor

A rotor made of ferromagnetic material rotates together with the camshaft. The Hall IC is located between the rotor and the permanent magnet, which produces a magnetic field vertical to the Hall element. When a tooth passes the sensor's sensing element, the magnetic field strength changes. Due to this, a voltage is induced and a digital signal appears in the Hall IC. Thus, rotation of the camshaft pulse sensor gear changes the Hall voltage in the Hall IC at the sensor head. The changing voltage is transmitted to the control unit and analyzed.

Operating diagrams of various sensors

The sensor is integral, that is, it includes a sensing element and a secondary signal converter. The main function of the sensor is to record the cylindrical phases of intake and exhaust. That is why it has a second name - phase sensor.

Signs of an error

There are a number of indirect signs by which you can determine that there are problems with the camshaft position sensor or its wiring. The situations described below may indicate other breakdowns, so if they occur, additional diagnostics with an error scanner (for example, the popular ELM 327 device or its equivalent) is needed. So, when a sensor error p0340 occurs:

It is worth noting that the listed changes in the behavior of the car are not so relevant for engines running on gasoline. The loss of power and increase in fuel consumption are not so great. The only inconvenience that can be noted is that the car starts worse, you have to turn the starter for a long time.

But as for cars equipped with gas-cylinder equipment, here the problems described above can manifest themselves “in full.” The loss of power and increase in consumption will be significant. Another trouble will await owners of cars that have modern gas equipment installed, in particular the fourth generation. So, this equipment has its own electronic control unit. And if a phase sensor error 0340 occurs (as the DPRV is sometimes called), there will be a constant disruption of the operating parameters. Because of this, gas-cylinder equipment, firstly, will need to be constantly reconfigured, and secondly, despite all the adjustments, it will still work in a non-optimal mode, consume more fuel and cause the driver problems with loss of power of the car, constantly stall and etc.

Chevrolet Niva error codes: decoding and description of meanings

The popular Russian-made model is very widespread in the CIS countries due to its optimal cost and increased cross-country ability, which is critically important in the conditions of domestic operation. Motorists buy cars for off-road travel and small towns, where the quality of roads leaves much to be desired.

The disadvantages of the car include weak wiring - when the load increases to the design limit, on-board electronic systems often fail, which causes software failures. Chevy Niva error codes appear on the dashboard display or are detected using special equipment, but the common thing is that they all indicate a malfunction of a specific component.

Error P1602

P1602 (Court Controller, Power Loss) is another common Chevrolet Niva error.

Code P1602 is entered if the following conditions are met:

The codes should be cleared using a scan tool. If the code is entered again, check the power supply circuit from the battery to pin “12” of the controller.

What errors have you encountered on Chevrolet Niva? You will find other reference information on ChevyNiva here.

Keywords: Niva on-board computer | Niva engine | esud niva

Share on social networks:

Found an error? Select it and press Ctrl+Enter..

Replacement

Unfortunately, it is not always possible to determine “by eye” whether the VAZ 2114 camshaft sensor is working. Sometimes it is necessary to dismantle it to inspect or replace it.

The main safety rule when carrying out work to replace the sensor is to disconnect the battery. If you break the rule, not only the sensor can burn out, but also the entire electrical wiring of the car, which is quite expensive.

The replacement procedure in 8-valve models is slightly different from 16-valve models, so if you have this option, you will have to read this paragraph separately.

The algorithm for carrying out work on an 8-valve engine is as follows:

1. We find the sensor on top of the engine, on the right near the air filter.
2. Using a 10mm wrench, unscrew the only bolt securing the device.
3. We remove the sensor.
4. We close the nest from which the device was removed to prevent debris and foreign objects from getting into it. This is necessary so that you don’t have to clean it after replacing it, and so that the new sensor doesn’t malfunction due to the fact that you won’t be able to clean it.
5. Wipe the device with a rag, remove any remaining dirt and oil, and clean the contacts. The rags must be dry. After cleaning, put the device back in place; perhaps the problem was due to contamination (which happens very often).
6. If after cleaning the device the situation with errors and problems has not changed, you will have to fork out for a new phase sensor.

FakeHeader

Comments 37

Yes, you can set everything without marks at all, use a screwdriver for the lower part, but it’s more difficult to use the upper part, you have to remove the cover

When replacing the kV rear oil seal, remove the flywheel. And sometimes they put it wrong. Then think about why problems appear

first think about what you wrote

I understand this perfectly well; on the former 11th, the marks on the timing belt did not coincide with the mark on the flywheel. On my Priora I only look at the kv mark by looking at the flywheel

Class. Continue in the same spirit, as long as no one follows you. No offense, but the mark on the flywheel is only for minimal imbalance and does not affect the timing in any way.

How to reset faults on Grant

1. Warm up the engine to operating temperature, without exceeding the threshold of 2000 rpm.
2. Remove the terminals from the battery and leave the car without power for 15 minutes.
3. Return the terminals to their place and turn the key to position 2.
4. After 1 minute, turn off the ignition.

Diagnostic codes on Grant fully reflect the picture of possible breakdowns. Diagnostic codes help to accurately determine the location of the malfunction and quickly eliminate it.

Specialization : Graduated from the State Automobile University, worked for 20 years at GAZ-56, now I drive a Zhiguli.

Source