In the factory configuration, the Lada Vesta model is equipped with a rod-type hood support. Fixation method: inside the engine compartment cover. The design is impractical and partially limits the working area of the engine compartment.
Gas struts for hood
An effective solution is to install gas stops. Let's look at how to do this with your own hands using the Lada Vesta as an example.
Sequence of actions during installation
- key to "17";
- head, knob, knob extension;
- rags;
- additional lighting as needed;
- set of supports with two metal bases.
Algorithm for installing shock absorbers to lift the hood:
- We turn off the engine.
- We squeeze the handbrake and engage neutral gear.
- Open the hood.
- We unscrew the two nuts from the lower clamp at the base of the wing.
- We put a metal base on the bolts.
- Unscrew the two nuts at the top fastener and fix the shock absorber rod.
Where can I buy?
In addition to stationary auto stores, you can also buy hood stops for Vesta via the Internet. There are a lot of options, so there are no difficulties in this matter. The most popular offers, along with prices and articles, are reflected in the table.
| Manufacturer | vendor code | Price, rub.) |
| Rival | AB.ST.6011.1 | 2 970 |
| A-Engineering | KU-LD-VS00-00 | 2 050 |
| AutoUpor | ULAVES011 | 2 100 |
| Golden eagle | LVST.G2 | 2 300 |
| LADA | 99999218003300 | 2 290 |
| ATLANT | A60071 | 1 550 |
| TM | 8450008288G | 2 333 |
As you can see, prices can vary by almost 1000 rubles, depending on the manufacturer.
Recommendations for choosing gas struts for the hood
When purchasing, give preference to domestic products. In terms of workmanship, they are not inferior to foreign analogues, but the price is 20–25% cheaper.
The final decision is up to the owner of the technical device, but it is still necessary to listen to the advice of the experts.
Conclusion
The process of installing the stops is not at all difficult; the task is feasible for a car enthusiast without experience in servicing equipment. Before installing accessories, be sure to consult with service station specialists. Make sure the part is compatible with your car model.
Advantages of stops
Vesta hood shock absorbers have many strengths.
Height
The hood lid rises high enough so that the owner of the car does not hurt himself on it. There are no difficulties with access to the engine compartment. And the presence of shock absorbers will not allow it to rise above the required level.
The presence of stops allows you to raise the hood high.
Convenience
You can lift the Vesta hood with minimal effort, in any weather, and not worry about the cleanliness of your hands or clothes.
Fast installation
The manufacturers of this accessory saved the owners of the Russian sedan from the need for independent alterations and improvements. In addition, shock absorbers do not require maintenance or adjustment.
Attractive design
With such a device, Vesta immediately looks more respectable.
One of the Drive members, Schoolboy11, expressed his opinion about the stops in a story about his car Lada Vesta Red Menace
Reviews
| № | Positive |
| 1. | Sergey Ivanovich , 44 years old (otzovik.com): I use the standard mount, hood latch, there is more than enough functionality. |
| 2. | Fedor Stepanovich , 40 years old (www.zr.ru): I heard that you can install stops on the hood, but the price is steep for a quality product. I don’t think it’s necessary to purchase cheap analogues. |
| 3. | Vitaly , 22 years old (autobann.su): props are a good thing, but they also have a limited service life. |
| 4. | Daniil , 33 years old (lada-vesta.net): I looked at shock absorbers for the hood, the manager recommended domestic ones, and assured me of positive customer reviews. |
| 5. | Vitaly Semenovich , 43 years old (otzovik.com): I’ve been using the stands for a year and a half, I have no complaints, I also recommend it to my friends. |
| 6. | Stepanovich , 44 years old (www.zr.ru): satisfied with the purchase of racks, installed it myself, completed it in half an hour in total. |
| 7. | Vasilyevich , 20 years old (autobann.su): I bought domestic racks, I was right. They've been in service for two years and are in like new condition. |
| 8. | Tolik , 43 years old (lada-vesta.net): my positive review of the hood struts, six months have passed since installation, three-year warranty. |
| 9. | Stepan Nikolaevich , 39 years old (otzovik.com): they work properly, there are no drips, the rod has no play. |
| 10. | Konstantin , 43 years old (www.zr.ru): bought imported ones, good quality, five-year warranty. I use it with pleasure. |
| 11. | Anton , 35 years old (autobann.su): I can’t say anything bad, the supports are of average quality, they work quietly. |
| Negative | |
| 12. | Dmitry Viktorovich , 44 years old (www.zr.ru): shock absorbers leaked a year after installation, replaced under warranty. |
| 13. | Sasha , 37 years old (otzovik.com): in the second year of service they started to creak, I’ll contact the store for a replacement under warranty. |
| 14. | Nikolai Vasilyevich , 46 years old (autobann.su): I regretted that I bought supports, money thrown away. |
Criterias of choice
It would seem that such a simple accessory would be easy to choose. However, it is necessary to take into account some features so as not to be disappointed with the purchase later.
High-quality products are made only from high-strength steel, which guarantees their reliability. They should also be galvanized and powder coated on top - this will ensure no corrosion in the future, regardless of weather conditions.
Installing stops does not require dismantling the standard rod, which is used as a backup option, as well as changes in the design of the car or independent modifications. Therefore, there is no need to worry about losing your right to warranty service.
Quality products are guaranteed for a period of 3 years.
Video - Replaces the standard hood stop
It is usually necessary to open the hood of a car infrequently, however, AvtoVAZ’s decision not to install gas hood stops on the Vesta does not suit many people.
From the factory, the Vesta hood is fixed with a regular support (rod), which is initially attached to the hood itself. But this is inconvenient for 2 reasons:
- Sometimes your hands are full and you can hold the hood with one hand, but you can’t install a support with the other.
- Many people believe that placing the rod on the hood is not entirely correct, since you can inadvertently catch the edge of the wing, which sometimes happens. In this case, it would be more appropriate to place it on the body.
Purchasing and installing hood stops on the Lada Vesta solves this problem - with them you only need to slightly push it up and it will lock itself. Thanks to the pneumohydraulic system, they can improve the consumer qualities of your car. After installation, you will no longer need to hold the hood with your hands, thereby getting your hands and clothes dirty. With a hydraulic stop, just lift it slightly, and then the hydraulic mechanism will do all the work for you.
The ease of installation allows you to mount the gas struts yourself; you do not need any modifications (drilling the body) or additional costs for components; everything necessary for fastening and installation instructions are included in the kit.
Equipment:
- shock absorbers 880018 – 2 pcs;
- wing bracket – 2 pcs;
- hood bracket – 2 pcs;
- special nut – 2 pcs;
- washer 8 – 2 pcs;
- corrugation – 2 pcs;
- clamp – 2 pcs;
Gas hood stops for Lada Vesta, SV and Cross
The price is per set!
Warranty 3 months
Our store in St. Petersburg offers gas struts for the Lada Vesta car of excellent quality!
By installing these stops, you will be able to open the hood with minimal effort in any weather conditions, without fear of getting your hands or clothes dirty. The hood lid with these stops rises quite high and is securely fixed in the upper position.
Standard support
From the factory, the Vesta hood is fixed with a regular support (rod), which is initially attached to the hood itself. But this is inconvenient for 2 reasons:
- Sometimes your hands are full and you can hold the hood with one hand, but you can’t install a support with the other.
- Many people believe that placing the rod on the hood is not entirely correct, since you can inadvertently catch the edge of the wing, which sometimes happens. In this case, it would be more appropriate to place it on the body.
Purchasing and installing hood stops on Vesta solves this problem - with them you only need to slightly push it up and it will lock itself.
How to install hood stops
As previously noted, installation of gas shock absorbers is simple. The procedure takes a minimum of time and tools, as it does not require drilling additional holes. Manufacturers have taken into account all the nuances to facilitate the operation of the stops. It is necessary to carefully study the installation instructions and follow all instructions from specialists.
You should start working by securely fixing the hood, as a fall can lead to deformation and injury. Next, we proceed to install the brackets, for which we need to unscrew the bolts from the wing mounts. The procedure is repeated with the hood canopy, after which the bolts are inserted into place. After pumping the stops several times, we connect them to the brackets. The same steps are repeated with the second pair of fasteners.
It would seem that this completes the installation work, but it is worth considering a number of nuances. The most common problem when installing fasteners is compression of the hose through which water flows into the glass washer nozzles. It is important to carefully adjust their position. Very often, when closing, gas shock absorbers rest against the edge of Vesta’s plastic frill. Experts advise trimming the edge.
Based on the price and ease of installation, we conclude: the driver can afford such minor modifications to his car.
Hood stops
Automotive stores offer a wide selection of gas struts to suit any budget. You can purchase them at any auto supply store, or place an order online with subsequent delivery to a convenient address. Popular offers, along with prices and articles, are reflected in the table.
| Manufacturer | vendor code | Price, rub.) |
| A-Egineering | KU-LD-VS00-00 | 1950 |
| Rival Lada Vesta | A.ST.6007.1 | 2340 |
| AvtoBronya | ULAVES011 | 2100 |
| Vesta—shop | A60071 | 1800 |
| RS—motor.ru | rs-0004-upor | 1690 |
| Patriot | PTU 48.02 | 1900 |
The difference in price between the models is within 1000 rubles. Having added up all the pros and cons, it’s easy to choose the right model. The main thing is to study all the information on the topic and follow the advice of knowledgeable people.
Gas struts on the hood of the Lada Vesta have the following advantages:
- the hood opens without additional effort with one hand, which is convenient if the other is busy;
- you should not be afraid of hitting your head, since the hood opens to its maximum height and locks in this position;
- clothes and hands remain clean in any weather;
- From time to time, drivers look into the engine compartment to check the oil level; this topic is especially relevant in the winter, when they often have to top up anti-freeze. How to open the hood with one hand, without unnecessary inconvenience? It's simple - installing gas shock absorbers will make your life much easier.
Analogs and price
The range of manufacturers offering analogues to the stops listed in this article is wide. When choosing gas struts for your car, pay attention to the following nuances:
- You should choose a model designed for your car, designed taking into account its features and technological holes, to avoid drilling the body;
- It is important to choose a galvanized model coated with powder paint. If left untreated, the part will corrode, which significantly reduces its service life;
- A well-made part has the advantage of a warranty period.
Installation
Self-installation of Lada Vesta hood shock absorbers is very simple. There is no need to drill any holes - everything is mounted in standard places.
First you need to open the hood and lock it securely. Next, all that remains is to unscrew one or two wing mounting bolts (depending on the design of the stop brackets) and place the bracket under them, and then tighten the bolts. Next, the bolts from the hood canopy are unscrewed, under which the bracket is also installed, after which the bolts are screwed into place. The second pair of fasteners is installed in exactly the same way.
This video shows the installation of hood stops on Vesta:
All that remains is to bleed the stops 3-4 times, and then install them on the brackets. That's it, the independent installation of Vesta hood shock absorbers is complete.
However, some difficulties may arise. Sometimes the stop pinches the hose supplying water to the glass washer nozzles. If this happens, you need to move its mount a little. In addition, sometimes you have to trim the edges of the sedan's plastic frill a little so that the products do not rest against them when the hood is closed. It is the moment with the frill that is demonstrated in the video:
