Replacing the air filter for Lada Vesta. expert advice on choosing


The reliability of the vehicle depends on the technical condition of all systems. Filter elements are the primary sources of protection for technical fluids, air systems, and gasoline from possible contaminants. If the car was purchased at a car dealership, the requirement to replace filters at strict intervals is mandatory. The dealer has the right to cancel the manufacturer's warranty if the terms are violated.

If the car owner decides to change the filters himself, you need to take care of a covered room with an inspection ditch and lighting. You can change the oil and fuel filters only in conditions similar to those of a car service center. For models with 1.6 l and 1.8 l engines, standardized filters are used.

An alternative to an inspection ditch is an electric lift that can hang a car to a height of 1.5-1.8 meters above ground level.

Consequences of untimely filter change

The consequences of not changing the filter do not appear immediately, and the car will continue to drive for some time. The first signs will be a drop in traction levels and an increase in fuel consumption. Due to increased gasoline consumption, black soot will form on the spark plugs. This will damage the spark plugs and require them to be replaced. And at one point your LADA Vesta will stop starting and will not be able to take you where you need to go. And often this happens when you need to hurry, when urgent matters await. So it’s better to follow the instructions provided by the factory, change worn components on time and not take risks. And it wouldn’t hurt to replace the oil filter; we have an article about this on our website.

Replacing the Lada Vesta air filter

The new VAZ can be equipped with 1.6 and 1.8 liter petrol engines. The designers decided to leave the filters the same as for foreign cars, which avoided confusion (if the Vesta is not serviced at a dealer). This filter can be replaced by anyone who has the slightest understanding of what is under the hood. For those who do not understand, but want to understand, there is a lot of literature that “chews” the work process. The manufacturer prescribes changing the filter after 30,000 km (15 when operating in dusty areas), but inspection must be carried out 3-4 times more often. This is easy to do: on a Lada Vesta car, the air filter is located in a black plastic box on the right side of the engine.

Advice: it is better to open the case when the engine is warm.

The lid latches are made of brittle plastic and may break. To open the box, use a thin screwdriver to pry up 2 latches and pull out the cleaning element without disconnecting it from the lid

Is the filter damaged or heavily soiled? Change it urgently! No normal specialist can recommend vacuuming and blowing with a compressor, then putting it back in place and moving on (we don’t take into account emergency cases like “getting to the garage/shop”)

New Generation

Today, the MANN-FILTER brand presents a new generation of air filters made using Flexline technology. These filters can be integrated into any limited space under the hood thanks to the unique flexibility of the external circuits. Laser cutting technology makes it possible to obtain filters of any configuration that can be installed in any free space. The task is not just to cut the filter material into the desired shape, but also to glue it so that it does not come apart. Today only MANN+HUMMEL does this. One of the main advantages of such filters is the ability to increase the area of ​​the filter material by 8% while maintaining compact dimensions.

Such complex filters are used on Mercedes A- and B-classes presented last year in Geneva. But perhaps soon innovative air filters will be required for other brands of cars.

Air filter: the main misconception of all (almost) drivers

Review of Manufacturer Prices

Name / Catalog articlePrice, rub.)
Original
Pilenga FA-P0443 from RenaultFrom 800
High-quality analogues
Nevsky filter NF6433From 350
NF6433C (carbon filter)From 400
TSN Citron—/—
SibTEK—/—
BIG Filter, GB9978From 450
Ekofil, EKO0441—/—
LADA Vesta/X RAY 272773016R (Vesta 1.8)—/—
Mann CU22011—/—
Patron 5454211—/—

*prices are as of January 30, 2019.

Recommendations for selection

Service center specialists strongly advise purchasing consumables with original factory catalog numbers. However, the high price of the “original” is not affordable for every car enthusiast. Therefore, they are forced to look for cheap but high-quality analogues.

Always check the integrity of the packaging, the presence of protective holograms, and quality certificates. If anything is in doubt, it is better to refuse the purchase.

Conclusion

The process of replacing the cleaning element is simple, but requires care on the part of the repairman. Prevention will take no more than 10 minutes.

It is not necessary to contact a service station, but provided that there are no major breakdowns that require the prompt intervention of a specialist. Observe replacement intervals, buy original consumables.

The best air filters from domestic manufacturers

Russian automakers produce a full set of consumables for cars of their own production. The products meet the strict standards of automakers and have domestic and European certificates. A special feature is a good balance between quality and price. Our team recommends consumables from two companies that are distinguished by good service life, precise geometric dimensions and efficiency.

Lada

The Lada brand belongs to the Volga Automobile Plant, which produces modern cars for the domestic and European markets. The main activity is the supply of products to the VAZ conveyor. Provides the manufacturer and the secondary market with spare parts that do not differ in quality from assembly line components.

In the production of air filters, materials are used that are good at retaining dust and debris, but are not an obstacle to air flow. Innovative equipment installed in the workshops ensures uniform distribution of corrugations and no gaps between the filtration material and the frame. Lada consumables take into account the specifics of operation in Russia and the large number of bad roads in the country.

Advantages:

  • Low price;
  • Easy replacement;
  • Widely represented on the market;
  • The quality is constantly improving.

Flaws:

  • Lots of fakes from Southeast Asia.

Big Filter

The Russian company supplies components to the conveyors of domestic machine manufacturers and the secondary market. Big Filter filters are used by assembly plants of European and Asian brands, which are localized in Russia. The company works with well-known manufacturers of consumables from Europe and the United States, to whom it supplies products under well-known brands.

The enterprise has established multi-stage quality control, received international certificates, and representatives of automakers participate in inspections of production lines every year. Our own laboratory allows us to perform all types of tests. The basis of the range is panel and round filters, the production of which uses high-quality paper. The manufacturing process is automated, which eliminates the possibility of defects.

Advantages:

  • High efficiency;
  • Easy replacement;
  • Good quality packaging;
  • No fakes.

Flaws:

  • Not the widest range.

Blue Print

The German auto industry is known not only for the quality of its products, but also for the high cost of spare parts for its cars. If a part breaks in a Volkswagen, no matter where it comes from or what its role in the overall system is, the driver is doomed to incur significant costs.

British engineers from ADL decided to simplify life for lovers of German car brands, at least partially, and developed air filters for them that are not inferior to factory ones, but much cheaper. In addition, the aforementioned ADL produces cleaners for other foreign cars.

Blue Print's standard shape is rectangular. It is noteworthy that there is a special mesh that serves as protection against large fractions of debris.

Let's start replacing the LADA VESTA cabin filter.

To access the cabin filter of new LADA models, you no longer need to remove the frill and crawl under the hood. All manipulations must be carried out inside your car:

1. It is necessary to remove the right tunnel lining using a TORX T-20 wrench and unscrew the fastening screw.

2. You may need to remove the glove compartment lid. To do this, remove the side panel trim.

2.1 Take the TORX T-20 key in your hands and unscrew the screws securing the glove compartment (2 screws are located at the bottom, and 3 at the top).

2.2 Now we need to pull the glove compartment towards us. This must be done carefully, since it is also necessary to disconnect the connector for the glove compartment lighting. After the connector is disconnected, completely pull out the glove compartment and set it aside.

3. Next, remove the cabin filter plug. To remove it, you need to squeeze two plastic latches.

4. Take out the filter. To do this, it must be slightly compressed in the vertical plane.

5. Before installing a new cabin filter, you need to clean the seat.

6. We perform assembly in reverse order.

So we learned how to replace the LADA VESTA cabin filter with our own hands.

My blog is found using the following phrases

  • replacing the parking brake cable on a VAZ 2110 torrent
  • The signal does not work on the VAZ 21099 carburetor
  • how to check mileage on a vaz 2114
  • how to correctly position the bumper of an NP VAZ 2109
  • The signal does not work on the VAZ 2109
  • how to wind up the shield of a VAZ 2110

My blog is found using the following phrases

The recommendation of the manufacturer of cars such as Lada Vesta states that the air filter must be changed every 30,000 kilometers. For owners of previous VAZ models, this interval does not seem unfamiliar, since on the same Priora or Kalina it was exactly the same. But you should not strictly adhere to this recommendation, since under different operating conditions, filter contamination may be different.

  • If Vesta is used frequently in rural areas, especially with mostly dirt roads, it can be replaced at least every 10 thousand km, since even during this period the filter element will be quite heavily contaminated
  • And vice versa - in urban mode, where there is practically no dust and dirt, it is quite reasonable to consider the manufacturer’s recommendations and change it once every 30 thousand km.

If earlier you needed at least some tools to perform this repair, now you don’t need anything at all. Everything is done with your own hands without the use of unnecessary equipment.

Basic types and design

The consumable unit is constructed of 2 shells:

  1. The outer part is a housing with holes for air flow.
  2. There is a nozzle inside that is responsible for cleaning. The structure of the inner shell material affects the performance characteristics of consumables.

The modules are supplemented with a seal along the contour to prevent the appearance of a gap for dust and dirt between the housing and the working element.

Common types of air filters:

  1. Panel. Frame design with flat surface.
  2. Frameless. Models of simple design.
  3. Cylindrical. Only frame ones, often equipped with a pre-cleaner.

The module type corresponds to the car brand. You can select a consumable item from the company catalog, indicating the necessary information.

By material

The basis can be:

  • paper;
  • foam;
  • cotton;
  • metal;
  • synthetic material.

Paper filters are widely used. Porous paper is impregnated with resinous compounds to prevent moisture penetration.

Filters made of cotton gauze reduce resistance and increase air access. Full operation of the cartridge is supported by a reinforced frame and the density of the material. This type of consumable component reduces the induction noise of the running motor.

The performance characteristics of polyester sheets are several times superior to their paper counterparts, as they trap dust particles throughout their entire thickness.

The filtration fabric includes:

  • nanofiber;
  • wood;
  • synthetic resins;
  • additional connections.

The foam base for the protective element is made into multilayers of different densities. The shape is supported by a mesh.

The basis of metal structures are multiple layers of stainless steel mesh.

By shape

Types of consumables differ in appearance and are:

  1. Panel (frame and frameless). They are given strength by a reinforcing mesh, which prevents deformation and reduces vibration. Such modules are being developed for diesel and gasoline engines with injection systems.
  2. Cylindrical (always framed, with sufficient surface area). Does not require much space for installation. It is better to install it on cars with diesel power units and on commercial cargo vehicles.
  3. Round airy. A common design for passenger cars with carburetor engines. The ring shape of the consumable element is voluminous and requires sufficient space. The metal frame ensures the strength of the structure.

Null filters

The cleaning element of the module is foam rubber or cotton cloth. At the manufacturing stage, special compounds are used to process the material, the density of which correlates with the resistance to air flow. Such a cartridge reduces the output voltage to a greater extent compared to paper. The result is an increase in engine power.

The module is designed for reusable use, but requires compliance with the rules of care.

It is better to install zero consumable modules on sports cars. Passenger car engines will require expensive, thorough modifications.

By number of filtration levels

Consumable modules can have different degrees of air flow purification:

  1. One degree of protection is provided by a device that contains special paper or other dust-absorbing material. The load falls on only one layer.
  2. Two degrees of protection provide for the installation of a pre-cleaner in the path of the paper absorbent element. High-quality synthetic material is used. A rational choice for operating a car in difficult conditions.
  3. Three degrees of filtration are designed with the addition of pre-treatment by cyclonic rotation of the atmospheric mixture at the entrance to the sorbing system. Solid particles settle in the container or on the body of the device.

Replacing the cabin filter on Lada Vesta

Below we will consider when to change the cabin filter correctly, what is required for this, and what components are best to use.

Briefly about the purpose

The cabin filter is an element necessary to filter dust and dirt passing through the air flow from the outside. Such products are installed at the manufacturer’s factory, and are later replaced at a service station or by the car owner.

Common replacement options are a dust or carbon filter element. The latter provides a “deeper” cleaning from phenols and benzenes. The disadvantage of a carbon filter is its higher price.

Replacing the cabin filter of Lada Vesta 1.6 is simplified by the fact that the necessary element is located inside. This means “finishing” work, but with the dismantling of some parts.

Experts distinguish two options - with removing the glove compartment or without performing this work. The second method is preferable because it requires less time. For the purity of the “experiment” we will consider both ways.

Timing for replacing the cabin filter on Lada Vesta

Replacing the cabin filter on a Lada Vesta, provided that a high-quality part is installed, is needed after 15-20 thousand kilometers. Car developers set more flexible deadlines - 30 thousand kilometers.

But the manufacturer clarifies that its recommendation implies operating the vehicle in conditions of minimal air pollution.

In current realities, it is almost impossible to achieve this state, because in urban or rural conditions the level of dust is very high. That’s why it’s better not to delay the work and make a replacement after 10-15 thousand.

Signs of a malfunctioning cabin filter on Lada Vesta

In order not to waste time and money, it is important to identify the problem in time. Many car owners wait until the Lada Vesta service to replace the cabin filter.

This approach allows you to increase the time of use of the part and money. But in some circumstances it is better not to take risks and do the work right away.

Replacing the cabin filter on a Lada Vesta with and without air conditioning is necessary when a number of symptoms appear.

Let's highlight the main ones:

1. Deterioration in airflow quality when the corresponding function or heating system is activated. The malfunction is diagnosed by poor operation of the stove, which does not produce the required portion of warm air flow. In such a situation, the cause of the malfunction may not only be the filter element. Sometimes cleaning the air intake is enough to fix the problem.

2. The appearance of unpleasant “odors” in the cabin. The main sign indicating that the filter in the Lada Vesta is dirty is a stench when you turn on the blower or heating. This indicates that the filter device does not perform direct functions of air purification. To avoid illness or other consequences, a failed part must be replaced.

3. A layer of dust on the “tidy”. This is another sign that the cabin filter is not doing its job.

4. Fogging of windows. This symptom indicates a deterioration in the quality of the ventilation system, which is often caused by a dirty filter.

Consequences

If you ignore the problem, dust, small rubber elements, exhaust gases, harmful bacteria and other dangerous elements will enter the cabin, and then into the lungs of the driver and passengers.

In addition, contamination of the cabin filter is fraught with problems in vehicle operation:

1. The air flow deteriorates, which leads to a high load on the heating system. The motor operates at the peak of its capabilities, and this is fraught with overheating and failure. To change the stove, you will have to spend more time and money. It is not always possible to cope on your own, so you have to involve experts in the work.

2. Dust that accumulates on the air conditioner evaporator collects water. As a result, optimal conditions are created for the development of rust and the proliferation of dangerous microorganisms.

What to change for

Before starting work, you need to select and buy a cabin filter suitable for the Lada Vesta. The manufacturer supplies the simplest dust version (made of paper).

To install a similar part, it is important to know the catalog number (the original from the factory is Renault 272773016R). If desired, you can install another analogue or spend money on a higher quality carbon filter element

How much does a filter cost on Vesta - analogues

Advanced car owners know that original spare parts are more expensive than those with similar characteristics due to the “stamp” of the automaker. Manufacturers of spare parts and consumables for motor vehicles produce exact copies of parts installed on the assembly line, but for some reasons they set the price slightly lower than the products sold by dealers. Their characteristics are no worse (we don’t recommend taking the cheapest ones made in China, but it’s worth considering analogues from branded companies). At a similar cost to original components, few people will buy “non-original” ones, because it is not profitable to fool one’s head. In some cases, replacement parts will be even better quality than those installed by the factory and supplied to dealer services. We consider it useful to name the most popular replacements for Vesta filter elements from third-party manufacturers along with catalog numbers (next to the names):

The best air filters from Asian manufacturers

Companies from Japan, South Korea, Taiwan and China produce products that are supplied to Asian automakers and to the used car spare parts market in Europe and North America. The consumables are of high quality; innovative technologies and original materials are used in the production of air filters. Our experts recommend two of the best air filter companies from Asia, whose products are widely used in the European market due to their quality and effective air purification.

Sakura

The brand belongs to the ADR Group, the brand's factories are located in Indonesia. The company annually produces more than 100 million spare parts, which are supplied to the secondary market in Europe and the United States. Sakura has existing contracts with car manufacturers in Japan and South Korea. All spare parts are certified according to international standards.

In the production of consumables, thick paper with highly effective filler is used, which ensures the maximum degree of cleaning. Reinforced screen ensures durability of parts. Silicone-based anti-drainage material withstands high temperatures well.

Advantages:

  • Low price;
  • Good protection against counterfeiting;
  • High accuracy of geometric dimensions;
  • High-quality air purification;
  • Service life 10-12 thousand km.

Flaws:

  • There are many fakes on the market.

Masuma

The Japanese concern owns 80 enterprises in Japan, China, South Korea and Taiwan. The products are aimed at the assembly lines of Toyota, Honda and Nissan, and at the secondary market in Eastern Europe. The consumables are distinguished by the impeccable characteristics of filter paper, precise placement of corrugations, and good sealing of all joints. The filter material consists of fibers located at an angle of 90 degrees to each other. This design ensures the retention of the finest dust and does not impede the passage of air.

Masuma offers oil-based air filters that offer improved efficiency. Oil impregnation improves dust retention. In the production of frames, impact-resistant plastic is used, which increases the reliability of consumables and resistance to vibration loads.

Advantages:

  • Low defect rate;
  • Exact size match;
  • Good quality packaging with protection against counterfeiting;

Flaws:

  • Overcharge.

Replacing the Lada Vesta air filter

Its body is located immediately behind the battery. The cover is held in place by two latches, which should be pryed off with a screwdriver. It is better to warm up the engine to reduce the likelihood of clamps breaking - warm plastic is less fragile.

Now you can pull the cover towards you and remove the filter cassette. This must be done carefully so that dust does not fall into the inlet channel.

When you remove the air cleaner element, thoroughly clean the holder and the inner walls of the box. You can use a vacuum cleaner for this.

All that remains is to insert the new air filter and place the cassette in place so that the latches snap into place.

It is not recommended to try to clean out the old item and install it again.

Stages of replacing the cabin filter on Vesta

We will need

  1. flat and Phillips screwdrivers
  2. Key T-20 (asterisk)

Using a T-20 sprocket, unscrew the side screw securing the decorative cover

and using a regular screwdriver, carefully pry it up and remove it. (remove the cover slowly without breaking the plastic latches)

Now, using a flat screwdriver, carefully remove the plastic decorative side panel

Using the T-20 sprocket, unscrew the lower screws securing the glove compartment, as well as the 2 upper ones

Next, disconnect the backlight plug and move the glove compartment to the side

On the left we will see the filter housing closed with a lid. By pressing the latches we remove it

We take out the old filter and install a new one.

When installing the filter, pay attention to the arrow on the filter itself; it should be directed to the rear of the car, that is, in the direction of the wind flow. When installing a new filter, you need to bend it slightly to fit it into the housing hole.

When installing a new filter, you need to bend it slightly to fit it into the hole in the housing.

We reassemble in reverse order.

According to technical regulations, the air filter in Lada Vesta must be replaced every 30 thousand kilometers. When operating a car in bad weather conditions, the filter should be changed every 15 thousand kilometers. A clogged air filter affects engine life and power. The air passes through it worse, therefore the engine power decreases.

Which filter is installed from the factory?

The manufacturer equips Vesta with the original Lada filter 165460509R, its cost is about 800-900 rubles. However, if its cost seems too high to you, you can install cheaper analogues:

  • Pilenga FAP2180 price from 400 rub.
  • Ekofil EKO01200 price from 300 rub.

A regular non-charcoal filter is installed from the factory.

Dimensions of the filter

Instructions for replacing the air filter on Lada Vesta

Open the hood and see the air filter housing on the right side behind the battery.

Using a screwdriver, pry up the two latches of the cover and remove it.

Next, carefully remove the holder along with the filter.

We clean the housing and the holder itself from dust and install a new filter element.

We reassemble in reverse order.

Tips for operating the air filter on Vesta

  1. The old used filter must be disposed of; blowing it out and installing it back is not recommended.
  2. Replace the filter in accordance with the technical regulations or earlier, do not neglect the rules
  3. It is not necessary to use only the original filter; analogues also perform their functions perfectly.
  • How to replace the cabin filter on a Priora
  • How to change the oil in a VAZ 2114 engine yourself
  • Self-replacement of the cabin filter on a Lada...

Why does an engine need a filter?

The filter is of great importance for the proper operation of the car engine.
For 100% combustion of the combustible mixture, an increased air content is required: it must contain 20 times more air than the fuel itself. A standard car is capable of consuming about two hundred cubic meters of air mass over a run of one hundred kilometers. And all the air needs to be cleaned, since any suspension from it gets into the engine and clogs it. This provokes premature failure. Thorough, trouble-free operation prevents engine clogging. Some additional features are useful:

  • noise suppression;
  • regulation of fuel temperature level in gasoline engines.

During operation, the device gradually becomes clogged, and its ability to resist air flow increases.

As a result, less air gets in, and the mixture does not burn completely. The result is a concentration of toxins in the exhaust gases, reducing engine power.

Timely filter replacement will help maintain engine performance, health and safety. It is important to know which company has the best air filters and how to choose the right devices. Then the part will be as efficient as possible and will last a long time.

Analogues of the filter element for LADA Vesta

It often happens that car parts similar to the original ones are sold at lower prices. And we are not talking about cheap Chinese filters, but about products from branded companies. Often, such spare parts are not inferior in quality to the original ones, and in some cases surpass them in characteristics. Of course, if the price of the original and the analogue spare part does not differ much, most buyers will prefer to purchase the one installed by the manufacturer.

However, if it is not possible to contact a dealership for service, you will have to use a non-original spare part. It is for this case that we will list the most popular analogues of the LADA Vesta air filter, indicating the catalog number next to the name:

Mann Filter C27030

The filter element is from a German manufacturer, not inferior in quality to the original. But its height is 4 millimeters less than the one installed at the factory, but this does not prevent it from falling into place without any problems. The price of this filter is within 800 rubles.

Pilenga fap2180

The cheaper analogue, however, is quite popular. This filter element uses paper that is not of such high quality. In addition, after installation there are gaps between the filter and the seat. At the same time, the price of this product is much lower than the original - about 300 rubles.

BM fa2180

This product is manufactured by BM-Motorsport. It is the most popular due to its low price and decent quality. The characteristics of the filter correspond to the original ones. The price is within 180 rubles.

TSN (9.1.1736) and SCT SB295

They are high-quality analogues at a lower price. The average cost of these filters is 300 and 400 rubles, respectively.

It is worth paying attention to other analogues. However, before purchasing, in any case, you need to read reviews about a specific product on the Internet.

This will help you avoid buying low-quality products that will lead to costly breakdowns.

Options instead of the original

Some car enthusiasts, after identifying the need to replace the filter element, seriously believe that there is no need to buy a new one. They remove it and clean it, some even wash it and blow it out. Externally, after such manipulations, the filter looks like it came straight from the store. But it is worth considering that the filter is a consumable material and its mechanical properties are not unlimited. This product has its own service life. A filtration element cleaned in this way may be damaged in further operation, and the throughput will increase sharply, which will negatively affect the operation of the motor.

In addition, long-term operation of a car with such a filter can lead to failure of the spark plugs and mass air flow sensor. The engine control unit will begin to incorrectly calculate the proportions of the fuel-air mixture, and fuel consumption will inevitably increase. All this can be easily avoided if you promptly replace the Lada Vesta air filter.

Considering that the cost of this component on Vesta is not that high, there is no point in washing or blowing the product. As a last resort, you can purchase not the original consumable, but an analogue. It costs much less, and in addition, analogues of air filters are presented in sufficient quantities on the car accessories market. You can use a standard air filter, which is recommended by the AvtoVAZ plant. At the same time, analogues are not inferior in their characteristics to the original.

Products allowed for installation on Lada Vesta

Analogs Peculiarities
BM FA2180 from BM-MOTORSPORT.Perhaps the most popular among car owners. Mostly due to the low price, but in terms of its characteristics it is no worse than the factory one.
MANN-FILTER C27030 from MANN FILTER.A high-quality product, differs from the original in a smaller (4 mm) height, but retains all the necessary properties.
Pilenga FAP 2180 from Pilenga.It is in the middle price range, but has some disadvantages. The padding polyester layer is too thin and does not allow a tight fit to the inner walls of the case. The transmitting material is also not of the best quality.

Of course, you always want to save money and extend the service life of components. But in any case, even the cheapest air filter will be better than one you clean yourself. A new product always lasts longer and is more reliable than a used one.

Frequency of replacing the oil filter in Lada Vesta

The oil filter element performs an important function in the car - it cleans the incoming engine oil from chips and contaminants for optimal engine performance. Therefore, you should not neglect the manufacturer’s recommendations regarding the established replacement schedule.

As practice shows, the first replacement of the engine lubricant and filter device, according to the manufacturer’s instructions, is necessary after running in a new car, that is, after 3 thousand kilometers. The changing process is required in order to get rid of the chips that formed from grinding in the parts.

The Lada technical instructions indicate the need to change the filtration every 15 thousand kilometers or once a year, whichever comes first.

Since the operation of the car, as practice shows, often occurs in not the most favorable conditions, the repair period is significantly reduced - to 7,000 - 8,000 km.

You can understand that the Lada Vesta needs to replace the oil filter if at least one of the following symptoms is present:

  • intensive consumption of the fuel mixture;
  • difficulties when starting the engine for the first time;
  • the movement of the car is accompanied by jerks on small inclines;
  • spontaneous inhibition;
  • Traces of oil remain on the asphalt, which indicates a leak and clogging of the filter.

Often, the filter element is changed along with the engine oil itself.

Replacing the air filter on a Lada Vesta - algorithm

To carry out the work, you will need a new element, a clean, lint-free cloth, a blower (such as a vacuum cleaner) and good lighting (use additional lighting equipment if natural light is not enough). The sequence of actions itself is as follows:

  • install the car on an overpass (or just a flat surface);
  • block the rear wheels with “shoes”;
  • activate the parking brake;
  • turn off the engine and open the hood;
  • find the filter housing cover (refer to the manufacturer’s documentation);
  • press the latches to remove it;
  • dismantle the purifier;
  • carry out visual diagnostics of its condition;
  • install a new spare part (the cut should be on the front, the rubber edging should be on the back).

How to choose the right cabin filter

Autoreview experts tested 10 cabin filters in the Lefortovo tunnel and laboratory. They recommend following the following rules when choosing a cabin filter:

  1. Buy a cabin filter only with the original article number.
  2. The less the filter deforms in your hands, the better: the lower the likelihood of incorrect installation.
  3. The filter material must have a laminated coating on the side facing the fan so that fluff from the filter does not enter the ventilation system.
  4. The filter must be marked with the direction of air flow.
  5. The carbon filter does not necessarily have to be sealed in polyethylene: activated carbon “works” only with air circulation, which is virtually excluded inside the box lying in a warehouse or store.
  6. When the size of the box is much larger than the filter itself, this is not evidence of a fake. Many manufacturers prefer to save on packaging in this way: due to a smaller number of standard box sizes.
  7. The carbon filter must be selected by weight: a heavier one should be preferred - it contains more activated carbon.

Test results of ten cabin filters

:

Some test results for cabin filters according to ISO/TS 11155-1
FilterFlow velocity from deflectors, m/sFlow resistance, PaFiltration efficiency, %Dust capacity, g
TSN4,091461,718,3
Bosch4,132679,742,6
Delphi3,962878,937,3
Filtron4,122778,927
Mahle4,053279,947,2
Mann4,153379,946,8
RAF3,971848,721,5
Valeo42558,327,5
Volkswagen (coal)3,992779,340,7
Volkswagen (dust)4,091879,327
Some test results of cabin filters in the Lefortovo tunnel
FilterFilter weight, gHydrocarbons (methane-hexane), mg/m³Nitrogen dioxide, mg/m³Alcohols (isopropanol), mg/m³
TSN98,22,950,1111350
Bosch308,71,420,001424
Delphi226,61,450,036952
Filtron146,73,030,059800
Mahle290,61,570,004340
Mann306,21,610,004532
RAF164,43,190,0871143
Valeo157,71,430,035630
Volkswagen (coal)263,71,410,008763
Volkswagen (dust)81,93,040,11300
Used filter (Mann)328,43,130,019704
Without a filter3,210,1341378

Bold

The filters that turned out to be better than others are highlighted.

As a result, experts came to the conclusion

that a regular (dust filter) filter saves on your own health. But activated carbon can soften the blow to your health from inhaling nitrogen dioxide and unburned hydrocarbons.

Keywords: Lada Vesta filters | lada xray filters | air conditioner lada xray | air conditioner Lada Vesta | stove Lada Vesta | Lada Xray stove

5 1

Found an error? Select it and press Ctrl+Enter..

Recommendations for selection

Purchase consumables mainly at official points of sale. Do not use the services of unverified suppliers who sell products at reduced prices.


New filter

Check the tightness of the packaging, the presence of holograms, barcodes, dates and batch numbers. If you have any doubts about the quality and origin, do not purchase.

Conclusion

A clean air filter means good acceleration dynamics, low fuel consumption, and stable engine operation. Car owners often violate the replacement intervals for the cleaning element, thereby reducing the efficiency of the equipment.

Any car enthusiast without experience or skills in servicing a technical device can cope with replacing the air element. However, be extremely careful, as incorrect installation will lead to depressurization and the intake of untreated air from the outside. If you are experiencing difficulties or do not have free time, contact the specialists in the workshop for additional help and advice.

Where is the filter located

On cars of the Lada Vesta family, the cleaning element is located in the center of the dashboard in the lower part. It is a mistaken belief that the filter is installed behind the glove box. Place where the filter is located

To carry out preventive maintenance, temporary dismantling of the storage compartment will be required. However, experienced specialists practice replacing the cleaning element in a different way, which we will consider below.

When to change

In accordance with the manufacturer's recommendations, maintenance of the interior cleaner is carried out every 30,000 km. As applied to the CIS, Russia, among others, the interval is large.

  • reducing the force of air flow from the deflectors;
  • the appearance of a fetid odor and rot in the cabin, which is dangerous for the human respiratory system;
  • Leaves, dust, and dirt fly out of the deflectors when the stove heater is activated;
  • the onset of the time interval according to the instruction manual.

The algorithm for preventing the stove heater on Lada Vesta 1.8 is identical.

Preparatory stage:

  • new cleaner;
  • aerosol for cleaning the air conditioner evaporator (if necessary, its prevention);
  • screwdriver with a Phillips bit, TORX key set to “20”;
  • rags, plastic spatula;
  • additional lighting provided that there is not enough daylight for work.

Sequencing:

  1. We place the car within the perimeter of the repair area, provide priority safety measures, and squeeze the parking brake.
  2. On the passenger right side, open the glove box and remove the contents.
  3. We unscrew the three fixing screws and lower the glove box housing to the floor. First disconnect the lighting limit switches.
  4. On the left side of the opening, we snap off the plastic cover, squeeze the cleaning element with an accordion, and remove it.
  5. We blow out the cavity with a household vacuum cleaner or other device with a stream of compressed air.
  6. Place the new filter in the direction of the arrow towards you.

The second and most rational way to replace the interior air purifier:

  1. On the right side of the central channel, use a plastic spatula to pry off the cover. It is secured with three clips.
  2. We unclip the cover of the filter housing and remove it, after squeezing it with an accordion.
  3. We install a new cleaner.

Maintenance of the cabin air filter has been completed. We replace the carbon air element by analogy.

The best air filters from American manufacturers

The products of the American automobile industry are in demand all over the world. Companies from the United States produce high-quality consumables for cars of their own and European brands. Leading manufacturers are actively working in the global market, developing new segments.

Ford

The American company supplies its own assembly line with spare parts and produces consumables for premium cars. The concern's production facilities are located in 30 countries around the world. Ford has a developed network of representative offices, which allows you to have at your disposal any components and the necessary technical support.

The concern has one of the most powerful research centers that develops innovative materials for air filters. Consumables have low resistance to air flow, but retain debris and dust well. The materials used are resistant to high temperatures. The installation housings completely coincide in geometric dimensions with the original spare parts.

Advantages:

  • Increased resource;
  • Easy replacement;
  • Good protection against counterfeiting;
  • Available on the market.

Flaws:

  • The quality varies between factories.

BIG Filter

Air filters of the Big Filter brand are produced on the territory of the Russian Federation, in St. Petersburg. Judging by reviews and tests, it is one of the best air filters for domestic VAZs. Including the ratio of price and quality of air purification. So, the filter housing is of high quality, the seal is made of high-quality polyurethane. However, in some cases it is cast unevenly, but this is allowed by the manufacturer. The sizing is high-quality, the filter paper is thick, and has phenolic impregnation. Among the shortcomings, one can note only inaccurate cutting of the paper itself, which significantly spoils the impression and raises doubts among car owners about its effectiveness.

Real-life tests have shown that the new filter only allows about 1% of the dust passing through it. At the same time, the operating time of the filter is very high. The range of Big Filter air filters is quite wide, and the price of one set as of the beginning of 2019 starts from 130 rubles (for carburetor engines) and above.

Fram

The American company Fram occupies a leading position in the filter market, producing more than 4 thousand products. The catalog contains three series of products with increased service life. The maximum service life of Fram air filters reaches two years, even in off-road conditions.

When creating consumables, a filter element made of synthetic fiber, cellulose and fiberglass is used. The material has low resistance to air flow, but retains mechanical particles well. The adhesive roller secures the corrugations, ensuring maximum contact area with air throughout its entire service life.

Advantages:

  • Resource more than 20,000 km;
  • Easy replacement;
  • High strength of all structural elements;
  • Good protection against counterfeiting;
  • Developed network of representative offices.

Flaws:

  • High price.

Champion

The brand is well known to car owners for its spark plugs, which are supplied to the production line of leading Japanese, American and European manufacturers. Air filters are not inferior in quality. A special feature of the product is the absence of models with paper corrugations. In production, only synthetic fabric is used, which is characterized by high strength, durability, and low resistance to air flow.

Champion cylindrical air filters have a service life of 20,000 km, but often last significantly longer. In the brand's catalog you can select consumables intended for vehicles used in off-road conditions. The products are well protected from counterfeiting: there are holograms on the parts and packaging, and the high quality of printing and coding are noteworthy.

Analogues of the filter element for LADA Vesta

It often happens that car parts similar to the original ones are sold at lower prices. And we are not talking about cheap Chinese filters, but about products from branded companies. Often, such spare parts are not inferior in quality to the original ones, and in some cases surpass them in characteristics. Of course, if the price of the original and the analogue spare part does not differ much, most buyers will prefer to purchase the one installed by the manufacturer.

However, if it is not possible to contact a dealership for service, you will have to use a non-original spare part. It is for this case that we will list the most popular analogues of the LADA Vesta air filter, indicating the catalog number next to the name:

Mann Filter C27030

The filter element is from a German manufacturer, not inferior in quality to the original. But its height is 4 millimeters less than the one installed at the factory, but this does not prevent it from falling into place without any problems. The price of this filter is within 800 rubles.

Pilenga fap2180

The cheaper analogue, however, is quite popular. This filter element uses paper that is not of such high quality. In addition, after installation there are gaps between the filter and the seat. At the same time, the price of this product is much lower than the original - about 300 rubles.

BM fa2180

This product is manufactured by BM-Motorsport. It is the most popular due to its low price and decent quality. The characteristics of the filter correspond to the original ones. The price is within 180 rubles.

TSN (9.1.1736) and SCT SB295

They are high-quality analogues at a lower price. The average cost of these filters is 300 and 400 rubles, respectively.

It is worth paying attention to other analogues. However, before purchasing, in any case, you need to read reviews about a specific product on the Internet.

This will help you avoid buying low-quality products that will lead to costly breakdowns.

The best air filters for passenger cars

There are no ideal and completely universal air filters. Not every design is suitable for a specific car or its operating conditions, the year of manufacture and the level of wear of the car, and the high cost of consumables does not always guarantee maximum functionality and a long shelf life.

Therefore, we have compiled a rating of the 10 best air filters, in our opinion, taking into account a certain number of criteria - the reliability of the manufacturer, the presence of a wide model range of the brand, the adequacy and advantages of technical parameters, the balance of price, quality, performance and durability.

Nipparts

The filters are manufactured in Indonesia, are very precisely assembled and have virtually no defects. The designs are distinguished by a durable body, reinforced with stiffeners, providing fine filtration with a minimum coefficient of resistance. Allows you to significantly reduce fuel consumption.

The products are optimal for replacing original consumables with a wide range of popular foreign cars; they correspond to them in terms of performance characteristics, but are significantly cheaper. High quality packaged in durable polyethylene and a durable box, can be stored for a long time.

WIX


American premium class filters made of high quality materials, with integrated innovative technologies.
The products meet international quality standards, are certified and protected by a brand guarantee. They have the highest level of air filtration (9 membrane folds per inch) and can be used on vehicles operating under high loads and in conditions of high air pollution. Since they have a price “above average”, they are not in mass demand in the Russian Federation, but they offer the widest possible range of models (up to 5 thousand models) and are popular in the USA and the EU. Effectively replace original consumables on Opel, Volkswagen, Suzuki, Toyota, Nissan models, and are installed on Nascar racing cars.

Characteristics of the Lada Vesta cabin filter

LengthWidthHeight
216 mm200 mm35 mm

You can also install one of the most popular substitutes:

  • Pilenga FA-P0443 Price — 170 rub. Manufacturer: Pilenga. Has a regular filter element (not carbon). This model has higher popularity than the original. The reason is the good quality of the filter paper and the average cost is 3 times lower than the original. The coal model is not produced;
  • GB-9978 Price – 110 rub. Manufacturer: BIG FILTER. Having a low price, spare parts from this manufacturer have good reviews from Vesta owners. The filter element is slightly stiffer than the original. Coal version - GB-9978/C. Price - 130 rubles;
  • Finwhale AS433 Average price - 300 rubles. Manufacturer: Finwhale. Advantages over the original spare part - high-quality filter element and 2 times less cost. Coal version of Finwhale AS433C. Price — 390 rub.

Cabin filter Pilenga FA-P0443

Cabin filter GB-9978

Cabin filter Finwhale AS433

The best European manufacturers of air filters

The ranking of air filter manufacturers is opened by brands from Europe. They are considered one of the best, because they combine careful quality control, time-tested technologies and not the highest prices.

Mann-filter

The German company Mann is known for the high quality of any filters. Air filters for cars from Mann regularly top quality ratings. They are distinguished by tight fit, long service life (on average 20% longer than competitors) and high quality air purification. They are often installed in the factory equipment of foreign cars. The only drawback of the products of this manufacturer from Germany is the high price, however, this is offset by the fact that the filters do not have to be changed immediately after the end of the recommended service life (usually they retain their properties well. And this is also the best option for off-road driving.

Advantages:

  • excellent fit;
  • retain their properties for a long time;
  • service life is longer than most competitors;
  • filtration level is almost 100%.

Flaws:

  • high price.

Bosch

Bosch is a company that has become synonymous with quality for domestic manufacturers, and this applies to almost all products. It is worth noting that air filters from this manufacturer meet high quality standards only if they are produced in Europe. There is also a plant in Russia, but at equal prices it copes with the task worse. Bosch filters occupy the middle segment, have a high level of filtration, as well as good performance parameters. It is worth noting that sometimes European filters “stay” in warehouses and go on sale late, which can further reduce their service life. Therefore, when buying Bosch, you need to look not only at the country of origin, but also the date.

Advantages:

  • fairly inexpensive;
  • suitable for domestic and foreign cars;
  • big choice;
  • widespread;
  • perform their task well.

Flaws:

  • Russian filters are not very high quality;
  • may last less than stated.

Mahle

German Mahle filters, on the one hand, have an improved filter layer that lasts a long time and traps almost 100% of dust and allergens, but on the other hand, these filters often suffer from ill-conceived frames. It does not have stiffeners, and the frame is sometimes too thick, which can cause an unpleasant sound during use. However, this does not always happen, so there is no need to worry too much. Mahle filters are produced exclusively in Germany; they cost slightly above average, but given the performance parameters, they are very popular on the market. Often included in ratings of air filters for foreign cars.

Advantages:

  • improved filter layer;
  • made in Germany;
  • not the highest price for high quality;
  • serve for quite a long time - on average, enough for 16 thousand km;
  • widely distributed on the market.

Flaws:

  • not the most thoughtful design - some experience discomfort due to extraneous noise;
  • wear out quickly with frequent off-road driving.

Fram

These Spanish filters are very popular due to their price and quality. They allow less than 1% of dust to pass through due to the large amount of filter paper. And their service life is almost 30 thousand km, which is one of the best indicators on the market.

What happens if you don't change the filter?

If the driver refuses to change this part, the car will not stop moving immediately: fuel consumption will initially increase, traction will decrease, which will only be the “first bell.” Then black carbon deposits will begin to form on the spark plugs from an excess of incoming fuel (this will lead to the replacement of the spark plugs). One day your “vesta” will refuse to start the engine and give the driver and passengers rides about their business. This usually happens at the wrong time - which means it is better not to neglect the advice in the service book and replace worn-out car components in a timely manner.

For the successful operation of Lada Vesta cars, the manufacturer of this dust cleaner is not as important as timely monitoring of its condition and replacement with a high-quality new spare part. It is better to replace 3 “non-original” ones every 10,000 km than one “original” every 30+ thousand.

Signs of a clogged filter

A guaranteed way to check the filter is to dismantle it and visually inspect it. You can also determine the condition of the filter element by indirect signs:

  • turn on the blower for the stove or air conditioner - if the air flow is weaker than usual, it is necessary to replace the filter element;
  • when you turn on the blower, debris flies out of the air ducts - the filter element is deformed and needs to be replaced;
  • when the windows are closed while driving from the street, unpleasant odors penetrate through the stove - perhaps the filter cannot cope with filtration or is itself the source of the smell, it needs to be replaced;
  • when driving with air conditioning and the windows closed, dust quickly accumulates on the dashboard - the filter element is clogged and needs to be replaced;
  • Increased fogging of the windshield and side windows also indicates the need to replace the air filter element in the cabin.

If any of these symptoms occur, it is necessary to replace the cabin filter. The penetration of dust into the vehicle interior can harm the driver and passengers.

Read with this

  • Lada Vesta cross ground clearance ground clearance
  • How to replace the cabin filter on a Lada Vesta
  • Life hack: cabin filter on Priora
  • How to change cabin filters on Nissan X-trail crossovers of different generations
  • What will the Lada Vesta be like: body dimensions?
  • Replacing the cabin filter on a viburnum
  • VAZ Priora (Lada 2170)
  • Replacing the cabin filter in a ford focus 2
  • How to replace the fuel filter on a Lada Granta
  • Fuel filter Lada Priora
Rating
( 2 ratings, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]