We independently install and connect fog lights on Kalina

02/04/2022 3,885 VAZ Kalina

Author: Ivan Baranov

Despite the fact that anti-fog optics illuminate the road for only 10 meters, it still allows for safe movement by car in bad weather. In the absence of this type of headlights, visibility of the road will be limited, which will affect the safety of the driver and passengers of the car. How to install fog lights on Kalina and what headlights can be used for this - read below.

[Hide]

Principles of classification

PTF is characterized by a directional and long-range luminous flux. Taking into account quality and class, experts distinguish the following types of fog lights:

• square;
• round;
• double;
• for external installation.

On the second generation Kalina you can install halogen or xenon lamps. The latter type of optics has the following advantages:

• good brightness;
• long service life.

Experts recommend installing 2 fog lights from the German manufacturer OSRAM on the Lada Kalina. Optics of any color illuminate the road equally. Russian products are marked with the “E22” mark. Fog lights marked “02” meet all international requirements. There is a certain optics marking system:

• “C” - separate low beam device;
• “R” — high beam optics;
• “H” - headlight with halogen lamp;
• “PL” - a lamp with a diffuser made of optical plastic;
• “S” is a glass headlamp.

When choosing a fog lamp, experts recommend giving preference to optics with a sealed and durable housing and thick plastic. Glass headlights can quickly fail. You can install 2 aerodynamic fog lights with reliable fastening on Kalina.

It is better to install dismountable PTFs on the car. In such optics, you can replace glass or a burnt out lamp.

Standard kit (complete set)

Standard kit for mounting fog lights

The headlight kit includes:

1. Fastening frames.
2. The headlights themselves (2 pcs).
3. Bolts.
4. Wires with connectors at the ends.
5. Relay.
6. On/off button.
7. Connectors with which wires are connected.
8. Self-tapping screws.
9. Installation instructions.

The kit also includes a corrugation in which you can hide the wires. It will protect them from damage and negative external influences. The relay is installed in its standard location on the mounting block. It is marked 1119.

The mounting frames can be additionally repainted in any color. You can also immediately buy frames in the desired color. There are many colors of Kalina, but the frame companies also produce frames in all colors.

Repair work

To install some of the above models on Kalina 2 with your own hands, you will need to redo the fastenings. Otherwise you can choose:

• Fog lights from Bosch - German optics are equipped with high-quality glass. These fog lights are characterized by their range of light;
• optics from "Luch" - low price and quality;
• fogs "ProSport" (Chinese manufacturer);
• products from Kirzhach (lined headlights).

The fog lights come with plugs and covers. To install new LED or fog lights on Lada Kalina 2, you will need:

• optics kit;
• wiring;
• relay;
• button;
• fuse with holder;
• screeds.

PTF must be installed in standard holes. Otherwise, the headlights are positioned symmetrically with respect to the longitudinal axis (above 25 cm from the asphalt and at a distance of up to 40 cm from the side marker plane). The power of the lighting device should be within 50-60 W. The lamp base must have the following designations: H-3, H-1.

Before connecting the PTF, it is recommended to decide on the method of installing the optics:

• with preliminary removal of the bumper;
• without dismantling work.

The first method is used by beginners. Installation and connection of fog lights using the second method is used by qualified craftsmen.

Lamp replacement guide

It is more convenient to change light bulbs in PTF on a lift or inspection pit. To do this, you need to purchase either the same light bulb as the one you had, or one that matches the parameters. Changing a light bulb is easy.

To do this, follow the following sequence of actions:

1. To remove the optics, you need to unscrew the mounting bolts.
2. First you need to move the rubber protection to get to the PTF power supply block.
3. Then you should disconnect the block from the optics.
4. To remove the light bulb, you need to gently press one end of the latch and slide it down.
5. The light bulb is removed along with the base. The halogen lamp has several contacts that should be remembered in order to correctly install the new one.
6. Next, you need to install the new product so that all contacts match. If you make a mistake, the fog lamp will not light.
7. Assembly is carried out in reverse order.
8. After assembly, you need to check the operation of the optics.

Replacing fog lights on other car brands depends on their design features. There are cars on which the fog lights are located together with the head light, in which case a slight disassembly of the optics will be required. An example would be the Lada Kalina.

Step-by-step dismantling instructions

To dismantle the front bumper with your own hands, you must first unscrew the fasteners. They are located under the radiator grille. Then unscrew the fasteners (from the wheel arches), with which the bumper is fixed. The side panels of the latest design are brought out from under the wheel arches. The next step is to dismantle the bumper.

To remove the plugs, use a flat-head screwdriver. The foglights are screwed on with self-tapping screws. For 1 headlight you will need 3 fasteners. The seal located under the clutch pedal is pushed out. The wires from the optics are pulled out. For this purpose, metal wire is used. The wiring from the PTF is connected to the main wiring.

Since PTF consumes 110 W, the connection diagram for such optics requires the installation of a relay. The control button is mounted on the dashboard. Power supply to the optics is made using the pink wire located in the fuse box. The current strength of the fuse used to connect the fog lamp should be 15A.

After drawing up the diagram, it is recommended to independently check the correctness of the connections. Then connect the power supply terminal. The button installed on the dashboard turns on. If the above work is done correctly, then the headlights work normally. To obtain “cold” lighting, xenon is inserted into the PTF. The next step is to install the bumper and re-check the correct operation of the chain.

Replacing a light bulb in a fog light on a Renault Logan

1). Remove the protective shield on the bumper.

2). Disconnect the wires from the light bulb and pull it out.

3). We install a new lamp and connect it.

Replacing the light bulb in the fog lamp on a Hyundai Solaris

1). We remove or turn out the wheel and use a screwdriver to unscrew the clips securing the fender liner.

2). In the same way, remove the clips securing the lower front fender liner to the front bumper and bend the fender liner back.

3). Next, carefully turn the lamp counterclockwise and pull it out of the fog lamp.

4). We disconnect the power plug, take a new lamp, connect the plug to it and install it in the fog lamp. Turn it clockwise, check for functionality and screw the fender liner back on.

5). At this point, the process of replacing the lamp in the car's fog light can be considered complete.

Light adjustment

When the headlights are installed, you need to adjust their direction and brightness. Lada Kalina of the second generation is installed on a flat surface (5 m from the wall). Then one headlight is covered with cardboard. When rotating the adjustment screw, monitor the boundary of the outgoing light flux (below 0.5 m from the light level of the main headlights).

To make precise adjustments, use a regloscope.

The principle of its operation is that counter optics with a photocell are installed in front of the light source. In this case, its optical axis should be parallel to the longitudinal axis of Kalina. The use of a mirror orientation system allows for precise adjustment of the headlights. In the absence of proper experience in using a regoscope, diagnostics of fog lights should be performed by a specialist.

A photoelectric device is used to measure the luminous intensity of the optics. Multifunctional regloscopes allow for detailed analysis of light distribution. A similar technique is used at service stations.

tweet

back How to choose an armrest for Kalina

Next Advantages and disadvantages of installing a spoiler on Kalina station wagon

Tagschoice, foglight, installation, headlight

Do-it-yourself PTF installation

To work you will need:

1. The key is "8".
2. Screwdriver.

It is recommended to carry out work on a removed bumper. It will be more convenient this way. You can also mount the headlights directly on the car. After installation, be sure to check the quality of work and adjust the headlights so as not to blind oncoming drivers.

1. The steering wheel needs to be turned all the way.
2. Remove the dirt protection in the wheel arch.

Unscrew all the bolts and carefully remove the protection

3 self-tapping screws for securing the PTF lamp

Without decorative overlay

Now with overlay

The same actions should be performed on the other side of the car. At this point, the work on installing fog lights on the Lada Kalina can be considered complete.

Connecting PTF to car wiring

Connection diagram of PTF to electrics on Lada Kalina

Initially, the wires must be connected to the headlights themselves. The “mass” is also screwed to the car body. “Plus” is connected to the battery according to the diagram. The wires are pulled through the engine compartment to the passenger compartment.

We pull the wiring into the salon

This must be done along the left wing, where the standard fastenings for the wires are located. Before doing this, you need to remove the fender liner to make work easier.

We will infiltrate here

Connecting fog lights in the cabin

1. Remove the ashtray by unscrewing the mounting bolts (4 pcs).
2. Next, you need to pull out the panel on which the button covers are located through the resulting opening.

We remove the console for easier routing of wires, you can push them in like that

Separate PTF activation button in the cabin

Connection to the LCM (light control module). Now the PTF can be turned on only when the dimensions are on, and when the ignition is turned off, the PTF will go out automatically, everything is according to the “law”

Selection of PTFs and their prices

This set is sold in almost all VAZ auto stores.

Lada Kalina is equipped from the factory in some trim levels with domestic “fog lights”, which are manufactured in Ryazan. You can also find many other headlights on sale from different manufacturers. Kalin owners recommend paying attention to LED products - they are both modern and economical, because diodes consume less electricity.

LED PTF

Prices for LED fog lights start at 2000 and can reach more than 20 thousand rubles.