VAZ oxygen sensor resistance

How to check the lambda probe and signs of malfunction? Is this a universal option from Bosch?

Car shakes when you drive at low speed - 2 answers

Firstly, in the event of a breakdown and malfunction of the labda, several tangible consequences appear in the behavior of the car:

Increased fuel consumption
Unstable operation of the car engine (jerks)
The operation of the catalyst is disrupted (toxicity increases)

So, to check the lambda probe, you can first unscrew it and do a visual inspection (just like a visual inspection of the spark plugs can tell you a lot).

There are several types of lambda installed on cars; the sensors can have one, 2, 3, 4, even five wires, but it is worth remembering that in any of the options, one of them is signal (often black), and the rest are intended for heating (usually white colors).

What and how can you check the lambda?

To check, you will need a digital voltmeter (preferably an analog voltmeter, since it has a much lower “sampling time” than a digital one) and an oscilloscope; if possible, the measurements will be more accurate. Before carrying out the test, it is advisable to warm up the car, since the lambda works properly at temperatures above 300C°.

First, look for the heating wire:

We start the engine, do not disconnect the lambda connector. We connect the negative probe of the voltmeter (regular store) to the body. Using a positive circuit probe, we “hit” each contact of the wire and observe the voltmeter readings. When the positive terminal of the heater is detected, the voltmeter should show a constant 12 V. Next, using the negative probe of the voltmeter, we try to find the negative wire of the heating element. We turn on the remaining contacts of the sensor connector. If a negative terminal is detected, the voltmeter will again show 12 V. The remaining wire is the signal wires.

Where to buy car accessories

Spare parts and other products for the car are easily available for purchase at auto stores in your city. But there is another option that has recently received significant improvements. You no longer need to wait a long time for a parcel from China: the AliExpress online store now offers the opportunity to ship from transshipment warehouses located in various countries. For example, when ordering, you can specify the “Delivery from the Russian Federation” option.

Follow the links and choose:

Checking the lambda probe with a tester:

We take an electronic constant voltage millivoltmeter and connect it in parallel to LZ (“+”, “-” to LZ, - to ground) and the lambda probe must be connected to the controller.

When the engine warms up (5-10 minutes), you need to look at the voltmeter needle. It should periodically change between 0.2 and 0.8 V (that is, from 200 to 800 mV, and if less than 8 cycles occur in 10 seconds, it’s time to change the LZ. Also replace if the voltage “stays” at the level 0.45 V.

When the voltage is always 0.2 or 0.9 V, there is something wrong with the injection - the mixture is too lean or too rich. Because the oxygen sensor voltage must constantly change and jump from 0.2 to 0.9 V.

There is another quick way to check the lambda probe. It should look like this:

Carefully pierce the positive contact of the tester (black lambda wire), the other contact to ground. With the engine running, readings should range from 0.1 to 0.9 V. Constant readings (e.g., always 0.2) or readings outside this range or fluctuations of lesser amplitude indicate a sensor failure.

always 0.1 - low oxygen
always 0.9 - a lot of oxygen
The probe is fine, the problem is different.

If you have the time and desire to bother, you can conduct several tests for a rich and lean mixture, and also additionally check the lambda probe sensor.

Disconnect the oxygen sensor from the shoe and connect it to a digital voltmeter. Start the car and, by pressing the accelerator pedal, increase the engine speed to 2500 rpm. Using a fuel enricher, set the speed reduction to 200 rpm.
If your vehicle has an electronically controlled fuel system, remove the vacuum hose from the fuel pressure regulator. Look at the voltmeter reading. If the instrument needle approaches 0.9 V, then the lambda probe is working. A sensor malfunction is indicated by the voltmeter not responding and its readings being less than 0.8V.
Take the lean blend test. To do this, take a vacuum tube and cause an air leak. If the oxygen sensor is normal, the digital voltmeter reading will be 0.2 V or less.
Check the operation of the lambda probe in dynamics. To do this, connect the sensor to the fuel system connector and install a voltmeter parallel to it. Increase engine speed to 1500 rpm. The voltmeter readings with a working sensor should be at the level of 0.5 V. Another value indicates a failure of the lambda probe.

Checking the voltage in the heating circuit

A voltmeter is needed to check the voltage in the circuit. We turn on the ignition and connect the probes to the heater wires (you cannot disconnect the connector, it is better to pierce it with sharp needles). Their voltage should be the same as the battery voltage when the engine is off (about 12 V).

If there is no plus, you need to go through the battery fuse sensor circuit, since it always goes directly, but the minus comes from the ECU, so if there is no minus, let's look at the diagram on the block.

Checking the lambda probe heater

In addition to measuring the voltage with a multimeter, you can also measure the resistance to check the serviceability of the heating element (two white wires), but you will have to take an Ohm tester. The documentation for a specific sensor must indicate the nominal resistance (usually about 2-10 Ohms), your task is only to check it and draw a conclusion. The video shows this method:

Checking the oxygen sensor reference voltage

Switch the tester to voltmeter mode, then turn on the ignition and measure the voltage between the signal and ground wires. In most cases, the lambda probe reference voltage should be 0.45 V.

A modern car is an electromechanical system consisting of many parts and assemblies interconnected by a series of different sensors. These sensors keep the vehicle in good working order and ensure it runs productively. Today in this article we will talk about the oxygen sensor (lambda probe). In particular, we will answer the question of how to check a 4-wire lambda probe with a tester. This is the most common type of sensor and is very important. Before you begin to study and test the performance of the LZ, it is advisable to briefly study its design characteristics, types and principle of operation.

Diagnostics

As always, before replacing any device, it must be checked for functionality. To diagnose a lambda probe, a regular multimeter will do; its reading scale may have the following values:

0.8-0.9V – normal indicator of the upper signal level;
0.1-0.2V is the standard for the lower one.

According to the manufacturer, the operational life of the device is more than 80 thousand km. But only on the condition that all GOST requirements during the manufacturing process of the oxygen sensor were met. Reviews from experienced drivers truly confirm the high service life of the product. Moreover, according to them, on average, a lambda probe lasts twice as long, and this is no more or less - 160 thousand km.

What effect does DC have on engine performance?

A working oxygen sensor is the key to the smooth functioning of the power unit. A minimal decrease in the characteristics of the air and fuel mixture, which this particular device controls, leads to a decrease in engine efficiency. Stable speed, absence of fluctuations and, in principle, correct operation of the engine directly depend on the lambda probe.

If, when you sharply press the gas pedal, the car jerks and the power unit noticeably shakes, there is a possibility of the DC failure. It is very possible that this behavior of the car is caused by the inability of the lambda probe to adjust the mixture to the engine speed.

In addition, when an increased emission of exhaust gases into the environment is noticed, the cause is also most likely in the oxygen sensor. After all, it is he who is responsible for destroying the remaining harmful substances in the exhaust pipe.

What is the secret of the device’s effectiveness?

If you do not want to resort to the procedure of replacing the lambda probe before its service life expires, we recommend following some recommendations:

do not ignore the requirements specified in the manual for the VAZ 2114, use only the optimal brand of gasoline;
When adding individual additives to fuel, make sure their quality and compatibility with your car brand;
say no to sealants as a fixing element during sensor installation;
if you have problems starting the engine, do not torture the car by continuously turning the starter, always maintain a certain pause between attempts;
When diagnosing cylinders, never turn off the spark plugs;
The lambda probe has its own temperature limit, which is 950 degrees, so avoid overheating the exhaust system;
aggressive chemical substances can damage the electrodes of the oxygen sensor, eliminate the possibility of their use for processing the main element of the DC;
The connection between the lambda probe and the exhaust pipe must always be sealed, make sure this is done.

Main symptoms of malfunctions

Every car owner knows that the car always warns of a future breakdown. The hints may be completely different, but the fact remains a fact! Therefore, if you are extremely attentive to the behavior of your vehicle, the problem can be solved even before it appears.

If we talk specifically about the VAZ 2114 oxygen sensor, signs of malfunctions may be as follows:

unstable speed, the car stalls when you gently press the accelerator pedal;
reduction in the dynamic characteristics of the car;
increased fuel consumption;
constant crackling in the catalyst area after turning off the engine;
the appearance of an aroma reminiscent of rotten eggs - this stench is simply explained by the fact that there is too much unburned gasoline in the catalyst.

Even if the failure of the oxygen sensor is obvious, do not rush to buy it. The fact is that, depending on the year of manufacture, the VAZ 2114 can be equipped with different modifications of the recreation center. So on old cars the manufacturer installed single-wire devices, now four-wire ones are in use.

What happens if you turn off the lambda probe?

Those who intend to ignore the manufacturer's requirements and disable the oxygen sensor should prepare for detrimental consequences for the engine:

the motor will not work correctly;
the level of harmful substances in exhaust gases will increase significantly;
consumption will increase;
there will be a need to reinstall the ECU software.

Based on this, each owner of the fourteenth model must draw certain conclusions. In order not to make a mountain out of a mountain, it’s easier to fix everything in a timely manner with your own hands. Or, as a last resort, visit a service station.

What is a lambda probe, principle of operation and its types

Therefore, an air sensor is a small device that is installed in the exhaust manifold of any modern car and serves to assess the concentration of residual oxygen in the exhaust gases. Thanks to the readings of this device, the computer unit of your car receives data on the basis of which it prepares the combustible mixture. The lambda probe takes into account the residual oxygen concentration in the burned fuel and sends a signal to the electronics that the newly supplied fuel mixture should be enriched or removed into the air. It goes without saying that if the lambda probe malfunctions, the operation of the car's engine may be disrupted.

Remember! To burn 1 kg of a mixture of fuel and air, you need to spend about 15 kg of oxygen.

Lambda probe device

A modern air sensor is a small structural device containing a number of interconnected parts.

Lambda probe design

Metal body with thread. It is designed to fix the sensor in the mounting hole;
Ceramic insulator;
O-ring;
Conductors;
Protective cover with ventilation hole;
Contact;
Ceramic tip;
Electric stove;
Exhaust port;
Steel shell.

As a rule, the start of exhaust gas measurements occurs at a temperature of 310-400 degrees. It is at this temperature that the special filler in the sensor becomes electrically conductive. Until the temperature reaches the desired value, the car's electronic control unit records the readings of other sensors, and only then the lambda probe. The peculiarity of its operation is that the exhaust gases and atmospheric air are separated by a container with a composition that generates current. Due to a certain chemical effect on this container on the pressure side and on the air side, a difference in oxygen concentration is created, based on which an electrical potential is created. The values of this potential are sent to the vehicle's control unit.

All oxygen sensors are divided into four types depending on the number of wires in their design:

1. Single wire; 2. Two-wire; 3. Three wires; 4. Four threads.

Types of lambda probes

All of the lambda probes listed above are available in narrowband and broadband.

Device diagram

Let's look at the probe diagram, which gives an idea of the placement of nodes. Knowledge of the design allows you to understand the locations of parts that are prone to failure.

Probe design example

The design includes:

1 - metal fitting intended for installing a probe, there are turnkey edges on the outer surface, a thread is located below;
2 - ceramic insulator;
3 — sealing element for inserting the wiring harness;
4 - signal wires;
5 - metal protective cap, equipped with ventilation vents, designed to protect the measuring element from damage;
6 — spring contact part;
7 - sensitive element made of ceramic;
8 - heating rod;
9 - ventilation duct;
10 - outer metal casing.

We recommend: How to determine that a valve in a car engine has burned out: signs and symptoms

The main causes of lambda probe malfunctions and the consequences of its breakdown

Having decided on the concept and characteristics of the oxygen sensor, we can conclude that it performs a key function in the normal operation of the internal combustion engine. So what can cause the lambda probe to break down and fail? There are two aspects to this issue: external factors and internal factors, which we read about below.

Leak in the coolant or brake fluid sensor housing;
Caring for the sensor using products not intended for such purposes;
Low-quality fuel with high lead content;
Overheating of the sensor, which also occurs when using low-quality fuel.

After the lambda probe fails, your car will begin to show signs:

Significant shocks when moving;
Excessive fuel consumption;
Poor performance of the catalyst;
Floating motor speed;
Excess toxic waste in exhaust gases.

The power of all of the above should push the motorist to check the lambda probe almost every 10 thousand km. Its complete replacement is desirable every 40,000 km.

What can the electronic control unit tell you?

If a warning light comes on on the dashboard, indicating errors in engine operation, and its lighting is accompanied by the above problems, it is advisable to test the controller. Today this can be done both at a service station and at home. Of course, if you have a special tester and a laptop (tablet, smartphone) with the appropriate software. When connected, this device will give you codes for possible problems.

For VAZ-2114 vehicles, a faulty lambda probe may indicate its malfunction with the following errors:

P0130 – incorrect sensor signal;
P0131 – excessive oxygen level in the exhaust gases;
P0132 – oxygen content too low;
P0133 – weak or slow sensor signal;
P0134 – lack of sensor signal.

Checking a lambda probe with 4 wires with a tester. Methods for checking LP

So, we come to the question that worries every motorist: how to check the lambda probe at home? To do this, you will need a regular tester (multimeter) or voltmeter.

4-wire lambda probe

The first step is to warm up the engine, then measure the resistance on the heater wires. As a rule, these are two white wires, the polarity of which can be ignored. The normal resistance between them should be from 2 to 10 ohms. If this value is different, the sensor is faulty.

Lambda probe voltage graph

Let's move on. Now you need to connect the negative terminal of the tester to the engine housing. In this case, connect the positive terminal to the signal wire of the sensor itself. This is usually the black wire. With the engine warm, press the accelerator pedal and increase the speed to 3000 rpm. Hold the pedal in this position for about three minutes. At this moment, the lambda probe heats up. You can now check the activation of the oxygen sensor.

The voltage between the motor body and the signal (black wire) of the part should fluctuate between 0.2 and 1 volt. For every 10 seconds that pass, the sensor should light up approximately 10 times. In cases where the tester shows 0.4-0.5 volts and does not turn on, we can conclude that the lambda probe is faulty.

You also need to know that when you press the accelerator pedal hard, the tester should show a voltage of about 1 volt. When the pedal is suddenly released - zero volts.

This is all for us. We hope that your sensor is fully operational and performs its intended functions. If you have questions, leave them in the comments.

General information and principle of operation

As the name of the part suggests, the oxygen sensor (DK) is a device through which the ECU receives information about the amount of oxygen remaining in the exhaust gases.

DC is a rather complex device in design. It consists of a ceramic electrolyte that can withstand extremely high temperatures, up to four hundred degrees. The electrolyte consists of zirconium dioxide, the surface of which is treated with yttrium oxide. The surface of the oxide is coated with platinum. The use of platinum is due to the fact that it is the material with the highest thermal conductivity.

In addition to the main electrolyte, the design of the lambda umbrella consists of the following parts:

Shielded tips, shielded on both sides from the electrolyte, with holes for air and exhaust gases. The tips, combined with electrolyte, are the main functional part of the oxygen sensor, with the help of which the analyzer device determines the potential difference;
The tips are a kind of housing, inside of which there is an element with high current conductivity (collector);
Between the tips there is a device that reads the resulting electrical signal;
All structural elements of the oxygen sensor are located inside a metal housing. The gland probe is separated by four wires: 2 white wires are responsible for powering the device, and two black wires - the first transmits the received data to the computer, the second - to the ground.

The principle of operation of the lambda umbrella is as follows: the electrolyte located in the exhaust gas flow of the car is heated to temperatures from 300 to 400 degrees thanks to the built-in heating element. This temperature is necessary for the zirconium to reach maximum conductivity and for the system to begin functioning. The central control unit is installed in such a way that the tip on one part of it is in contact exclusively with exhaust gases, and on the second tip - with clean atmospheric air.

When a sufficient amount of oxygen accumulates inside the manifold located inside the tip, the potential difference across the electrolyte changes, data about which is transmitted to the ECU, and the electronic systems of the fourteenth change the amount of fuel supplied to the cylinders.

The optimal ratio of fuel and oxygen in the fuel mixture is 14.7 to 1; it is at this ratio that the maximum efficiency of the power unit is observed.

The cost of a VAZ oxygen sensor for 2114 depends on the type of device: on the first models of the fourteenth, single-wire lambda umbrellas were installed, now they can be purchased at a price of 1.2-2 thousand rubles, on new models - four-wire direct current, they are more expensive, from 2 to 3 thousand.

Indicators

Lambda indicators may vary, but the car requires certain, optimal parameters.

Index

Peculiarity

Lambda equals one

Theoretically, this is the optimal air ratio, at which the actual amount is equal to the required

Lambda is greater than one

Indicates that the air-fuel mixture is lean and therefore the engine is not operating optimally.

Lambda is less than one

Under such circumstances, the mixture turns out to be rich and there is an excess of fuel. Because of this, there is a lack of oxygen necessary to burn such an amount of gasoline

If we talk directly about ideal conditions for the VAZ 2114 and its engines, then the lambda should have a ratio of 14.7 to 1. In other words, the mixture needs to be lean. This is due to the need for a sufficient amount of oxygen on the catalyst to burn CH and CO.

For domestic cars, a modern DC is used, which functions as a threshold element.

Checking the lambda probe

You can determine a DC malfunction and check the lambda umbrella using the following signs:

Problems with the engine at low speeds: the fourteenth stops or does not accept speed well;
Gasoline consumption has increased;
After turning off the engine, distinct crackling sounds are heard in the DK position.

The fact that it is necessary to check the oxygen sensor is also indicated by the presence of errors 131 and 134 on the instrument panel. These errors indicate that the device is emitting an incorrect signal and the problem should be sought in the sensor wiring or poor grounding of the device to the body. The presence of error 132 indicates that the supplied fuel mixture is too lean (large amount of oxygen in gasoline).

Before you pick up any electronic equipment, you need to familiarize yourself with its characteristics. The oxygen sensor pinout is as follows:

A - contact of the positive sensitive element;
C - contact of the negative sensitive element;
B - power cable of the heating device.

Knowing what the lambda probe pinout looks like, you can start checking the device. First, let's study the location of the oxygen sensor based on the type of engine of the fourteenth:

In a car with a 1.5-liter engine, it is located at the top of the exhaust pipe, next to the resonator;
Nawaz 2114 with a 1.6 liter engine, the lambda probe is located in the engine compartment, directly on the engine exhaust manifold. Keep in mind that on new models of the fourteenth, 2 DCs are installed simultaneously - the second one is located next to the first one, it is not difficult to find.

You can check the oxygen sensor on a VAZ 2114 at home with a regular multimeter, which can be bought at any auto store for 300-500 rubles.

Checking the oxygen sensor with a multimeter is carried out as follows:

We start the fourteenth and warm up the engine so that the central circulation reaches operating temperature;
We go into the engine compartment to check the lambda probe with a tester. We connect one multimeter probe to the negative terminal of the engine, the second to contact “B” of the oxygen sensor. If the tester shows that the voltage at the oxygen sensor is 12 Volts, the device is completely repaired; if the result is lower, the DC contact circuit is broken.
Next, we check the contacts of the sensitive elements “A” and “C”. Place the negative probe of the tester on contact “C”, and the positive probe on contact “A”. If the sensor is working, the tester will show 0.45 V. If the readings differ, you need to change the direct current.

Features of replacing the oxygen sensor

it is necessary to replace the faulty lambda probe with a completely similar device.

When going to a car dealership, take the broken device with you and check the markings located on the device body.

The algorithm of actions is as follows:

Disconnect all cables from the device;
Unscrew the DC with a wrench;
Screw in the new sensor. Be careful because the thread is easy to break;
We connect the sensor contacts according to the pinout diagram.

As you can see, there is nothing complicated in replacing the DC. Knowing how to check a lambda probe, determine the malfunction and install a new device in an hour and a half. It is worth noting that all of the above technology is also suitable for the VAZ 2115.

We hope this article was useful to you, the car owner!

How to check the oxygen sensor (lambda probe)?

Before replacing the oxygen sensor, you must make sure that it is the cause of the engine malfunction: decreased acceleration, decreased power, increased fuel consumption.

To do this we need to check the oxygen sensor.

List of possible malfunctions of the lambda probe (oxygen probe): -Heating does not work - loss of sensitivity - decreased performance (how to fix the sensor (reset sensitivity)?) As a rule, the death of the sensor on a car is often not recorded if the reason lies in the sensitivity of the sensor. But if the sensor heating circuit breaks, the on-board computer will immediately generate an error.

Checking the sensor power (voltage at the oxygen sensor)

Before replacing the sensor, you must make sure that it is turned on and all circuits are working properly. To do this, open the hood and disconnect the sensor connector (it is attached with a clamp to the cooling system pipe).

Checking the heating element circuit. We take the tester and connect its “minus” to the engine, connect the “plus” to contact “B”. Turn on the ignition and look at the meter readings - it should show 12V. If the tester readings are below 12V or there are none, the battery is discharged (which is unlikely) or the power circuit is open (we can eliminate the malfunction). The control unit is also faulty, but, as a rule, the on-board computer immediately shows this error.
Let's check the sensor circuit. We measure the voltage between contacts “A” and “C” minus by “C” plus by “A”. The voltage should be 0.45 V. If the voltage is missing or differs by 0.02 V or more, the power circuit is faulty (needs to be found and repaired) or the computer is faulty (which is also unlikely).

You can fully check the operation of the sensor only with the help of an oscilloscope, which most motorists do not have, so I see no point in describing this situation. I will only say that to check it you will need to artificially pump out and enrich the fuel mixture and look at the sensor readings.

If the sensor has already worn out a lot - more than 100,000 km, it can be safely replaced. Because even if it is working, the sensitivity has deteriorated significantly, which leads to unnecessary gasoline costs.

There are so-called “lambda probe simulators”. I’ll say right away that they will not fit our cars, because... The ECU does not read their signals.

You need to understand exactly how the sensor works. Please note the following errors.

Low signal level from oxygen sensor 1

Checking the oxygen sensor (lambda probe) on a VAZ 2114

The lambda probe on the fourteenth is part of the system that powers the engine. Estimate the amount of oxygen in the tube exhaust. This is necessary to properly adjust the mixture for the wheelbarrow to operate. By the way, such devices are installed only on the injector.

Oxygen sensor (lambda probe) VAZ 2114

Before checking the lambda probe, you need to imagine the main features of its operation.

The sensor, or rather what works in it, is a ceramic body with platinum. The operating temperature is from 350 degrees, while the lambda probe collects and mixes the mixture with the engine fuel system according to the readings of other sensors.

It works like this: the exhaust is filled with the (working) body of the lambda probe, it reads the difference in oxygen index from the exhaust and from the atmosphere and sends it to the electronic control unit, which is already processed.

Definition

The VAZ 2114 oxygen sensor is an electronic device that monitors the quality of exhaust gases.

Its second name, which is technically correct, is lambda probe. It works as an integral part of the electronic control system.

The service life of the lambda probe can be affected by:

working conditions;
fuel quality;
timely maintenance;
presence of overheating;
prolonged engine operation in critical mode;
timely maintenance and cleaning of the probe.

Under normal operating conditions, the lambda probe can operate for up to 7 years. As a rule, during this time a car can travel up to 150 thousand km.

Oxygen sensor location by engine type

On engines of different sizes, lambdas are located in different places in the exhaust system.

1.5 liters - located on the suction pipe, screwed on top, exactly in front of the resonator. It's easy to find, it's so lonely on the exhaust system, you can see it by driving a car into a hole.
1.6 liters - this engine has two oxygen sensors, they are located on the manifold. There may be one - for euro 2 and for euro 3 - 2 pieces.

As always, parts of the fourteenth plant tend to break down, but don’t rush to the spare parts warehouse. It is necessary to check the serviceability of the lambda probe; diagnostics often reveal completely different causes of malfunctions in the exhaust system.

How to check the oxygen sensor of a VAZ 2114?

For basic diagnostics you will need the following: Get a manual showing what an oxygen sensor looks like, you will also need an oscilloscope and a multimeter. Warm up the engine before checking the oxygen sensor.

But that is not all! Be sure to check the pinout of the oxygen sensor:

A - wire from the sensing element on the lambda with a positive potential,
C - wire from the lambda sensor with negative potential,
B - wire for the heating element on the lambda probe.

Now the check action plan:

We look at the diagram of the sensor device and check those parts of the system (their sensors!) that are affected by the lambda probe: on-board network leakage, ignition system, fuel supply system, look at the sensor housing and wiring - so that there is no damage.
The oxygen sensor must be removed and tested with a multimeter, which must be switched to voltmeter mode: start, press the gas to the ground at 2500 rpm, then reduce to 2000.
Fourteenth - injector, then remove the vacuum hose from the fuel exhaust pressure regulator, load it into a voltmeter, if the reading is close to 0.9 W, the lambda probe is in perfect order, if the reading is below 0.8 or not at all, the sensor has failed.
You can do a mixture test: take the same vacuum tube and create an air intake. When the lambda is working, the reading on the voltmeter will be up to 0.2W.
In this case, you should observe the behavior of the oxygen sensor: put it back on the exhaust system, parallelize the multimeter with it. We press the gas to the floor up to 1500 rpm, look at the numbers: if 0.5 W, then everything is fine.

A simple test of the lambda probe requires a basic understanding of what can break and what breaks most often:

If the heating in the oxygen sensor does not work,
If the device does not respond, it means that it has lost sensitivity to exhaust gases and the oxygen content in them,
Break in the contact system.

In the latter case, the on-board computer will give you an error that will indicate a faulty sensor. In other cases, nothing will show the fact of sensor death except self-diagnosis.

Visual inspection

The check should always begin with a visual examination of the condition of the oxygen sensor.

Inspect the wires. They must be intact, without traces of damage or defects. Check all connectors for tight connections.
Soot on the lambda probe indicates a malfunction of the device heater. Also, such deposits are caused by an excessively rich air-fuel mixture.
If you notice shiny deposits on the surface of the element, this indicates an excess of lead in the fuel you are filling the tank with. This situation requires mandatory replacement of the oxygen sensor, since lead could damage the internal device.
Gray or white deposits are the result of various types of fuel additives affecting the sensor. They often cause the probe to break and have to be replaced.

Reading errors

Checking the VAZ 2114 oxygen sensor may be limited to simply reading errors from the board, here are the most common ones related to lambda:

Error P0131 is a problem with the signal level coming from the device, it is too low, which indicates that the mixture is concentrated.
Error P0132 is a similar problem with the signal, only if it is an error, then the signal is high, which indicates a poor fuel mixture.

The errors displayed are not a panacea; they relate more to the fuel system and not to troubleshooting the lambda probe. That's why we found errors - look at what's wrong with the fuel pressure gauge and whether there is any air leakage from the atmosphere. Then diagnose the sensor itself.

The voltage on the oxygen sensor is one of the stages of checking its functionality. Before replacing or repairing a lambda probe with your own hands, you need to carefully check whether the device is receiving the necessary power and what condition the contact circuits are in. For this process, you need to open the hood of the fourteenth and remove the sensor (its connector is fixed with a small clamp on the cooling system pipe). We will look at two circuits: the heating element of the device and the oxygen sensing element on the sensor body.

To see the heating element circuit, you need to take a multimeter, connect its negative terminal to the engine, and connect the positive terminal to wire B. Turn the key into the ignition, look at the numbers on the multimeter: if 12V, then it’s normal, less - this is a dead battery (in rare cases ), broken contacts (most likely). Another option is to make a mistake on the electronic control unit, but here the on-board computer usually gives an error.
To check the circuit of the sensitive element, it is necessary to measure the voltage between wires A and C. We place the negative terminal of the multimeter on wire C, the positive terminal on wire A. We look at the indicator on the screen: if 0.45V, then everything is in order. If there is no number or it fluctuates within 0.02 V, the problem is in the power circuit. Again, the option is to make a mistake with the ECU, but this is not common.

Complete diagnostics of the lambda probe is only possible using an oscilloscope. Many people do not have such a device (despite the fact that many, in principle, do not know what it is or what it looks like). The test is tedious; measurements require special enrichment and depletion of the fuel mixture.

Many people ask how to remove a VAZ 2114 oxygen sensor, keeping in mind that there are substitutes for such a sensor. I don’t see the point in this: devices that simulate a lambda probe are not suitable for the design of the exhaust system of the Russian automobile industry (at least for Samara). The ECU simply does not read the signal it gives it.

Another point: if the mileage of the fourteenth has exceeded 100 thousand kilometers, you just need to change the oxygen sensor without waiting for it to fail (which rarely happens). If it works, it means it’s bad, the sensitivity is not the same and this is fraught with increased fuel consumption.

Symptoms of a problem

Now regarding the signs of malfunction. There may be several of them. Therefore, carefully monitor the behavior of your VAZ 2114. If you detect one of the signs, immediately take appropriate measures.

Location of the recreation center

When gas is low, the power unit begins to operate unstably, may stall, and floating speeds appear;
The dynamic parameters of the machine have deteriorated significantly;
Under normal conditions, fuel consumption levels increase excessively;
A cracking sound is observed in the catalyst zone after the engine is turned off;
You can hear the characteristic smell of spoiled eggs. Such stench is caused by the ingress of a large volume of gasoline into the catalyst, which is not burned.

If you need to replace the DC, check whether such a probe is installed on your car. On earlier versions of the VAZ 2114, single-wire sensors were installed, and then four-wire sensors appeared. Their price ranges from 1200-3000 rubles, depending on the type of recreation center.

If, when removing the device, you find that there is carbon deposits on the device, but the measuring device shows a slight deviation from the norm, it is not necessary to change the DC. You just need to get rid of the carbon deposits.

To do this, heat the sensor very much and then cool it quickly. This will allow the carbon deposits to crack and fall off. All that remains is to lightly wipe the device with a brush.

What if without a recreation center?

Many people ask whether it is possible to disable the recreation center and how this is done. We categorically cannot recommend doing this, since it leads to serious negative consequences:

The engine will begin to operate unstably and incorrectly;
Fuel consumption will increase;
The composition of the exhaust will deteriorate significantly;
You will need to reflash the on-board computer.

Therefore, if you find problems with the lambda probe, take the necessary measures to eliminate them. It's not difficult to do it yourself.