Firmware for the instrument cluster of Lada Granta and Kalina 2

To perform the procedure, you must have a device - a programmer. The most common version is the USBDM module.

The device connects to the PC and on-board system via standard cables. You will also need to download a specialized application to your computer. Usually the programs come bundled with the module and are installed on the computer without any problems.

The steps look like this.

• Find a programmer and download a special application to your PC.
• Mount the utility on your computer and connect it to the car via the programmer.
• Install additional power wires according to the factory diagram.

• The system is activated and the firmware procedure begins.
• Next, you must strictly follow the manufacturer's instructions.

Firmware on Standard version

For a standard modification of a car, the utility version 2190-00-040 or 042 is used. From here you can safely flash versions up to 076. Also, in some modifications of a Norma-type car, you may also encounter an assembly like 219020.

Firmware for Norma configuration

The steps and tools here are similar to the Standard assembly. To understand which firmware version is in stock, you should enter the required combination on the machine specified by the manufacturer.

Re-flashing the panel Grants FL

Nothing changes when you try to upload a new program to the flap of the FL version. The actions are completely identical. The only difference is the version of the utility itself.

Firmware versions of Lada Granta and Kalina 2 instrument panels

The table was compiled (is in the process of being adjusted) based on reviews from car enthusiasts (please add comments). There is no guarantee that all data is correct!

* — DTNV — outside air temperature sensor, DTOZH — coolant temperature sensor.

Download firmware (dumps of instrument panel firmware, links available for site users):

• 2190-50 — To download files you need to log in to the site
• 2192-50 (software 1.9) - To download files you need to log in to the site
• 2190-00-029 — To download files you need to log in to the site
• 219020-060 — To download files you need to log in to the site
• 219020-076 — To download files you need to log in to the site
• 219020-087 — To download files you need to log in to the site
• 219020-090(AT) - To download files you need to log in to the site sent by ARS190475
• 219020-091 — To download files you need to log in to the site
• 219020-096 - To download files you need to log in to the site sent by ARS190475
• 219040-046 — To download files you need to log in to the site
• 219040-047 — To download files you need to log in to the site
• 2190-3801010-50 Software: 6.6 (KP with two displays) - To download files you need to log in to the site sent by ARS190475
• 2190-3801010-50 Software: 7.2 (KP with two displays) - To download files you need to log in to the site sent by ARS190475
• 219220-014 — To download files you need to log in to the site
• 219240-006 - To download files you need to log in to the site sent by ARS190475
• 219240-007 — To download files you need to log in to the site
• 219240-009 — To download files you need to log in to the site
• 219240-012 — To download files you need to log in to the site
• 219240-014 — To download files you need to log in to the site
• 219250-2.5 (KP with two displays) - To download files you need to log in to the site sent by ARS190475
• 219020-092_for_076 — To download files you need to log in to the site
• 219020-092 — To download files you need to log in to the site (author)
• 2190-3801010-50 Software: 7.1 - To download files you need to log in to the site

FakeHeader

Comments 32

Kalina 2 after flashing from T007 to T012, the sounds of turn signals and emergency lights disappeared

There is a sound from the turn signals when the ignition is turned on...

I also had a gearbox from 007, now 012 - there is a sound from the turn signals.

there is no sound and the same thing while driving

So I did something wrong...

I have a grant from 2013. 1.6 98hp engine, automatic transmission, instrument panel 219020 - 076. Is it possible to install modified 092 firmware on it so that the technical specifications and TOC are displayed, will there be any problems with the automatic transmission indication.

Good day. Guys, tell me, the grant standard is 13 years old. Manual transmission. The firmware costs 219020_090. Which one can you upgrade to and how to have both the identity and technical specifications. If you can be more detailed because This is my first time encountering this, are there any nuances? I would be grateful! :)

You can flash it on software: 092

Instrument panel Lada Kalina, 11186 (2192380101020) can I install the automatic transmission standard on a grant?

No, from Kalina1 they do not fit to Kalina2/Granta

Hello, Granta automatic transmission 2013 firmware 009 but the coolant temperature does not show what can I reflash to?

009 firmware from Kalina, and it definitely has TOZH. May not show TOC if sensor is not installed.

Oh, I wrote 090 incorrectly, but if I set 009, it will show the automatic transmission switching? Can you tell me?

Firmware for the instrument cluster of Lada Granta and Kalina 2

Firmware for the instrument cluster of Lada Granta and Kalina 2

Have you encountered a problem where the outside air temperature is not shown in the instrument panel? Even after installing the sensor, the values ​​are not displayed on the screen. To correct this drawback, it is proposed to update the dashboard firmware of Lada Granta and Kalina 2 cars.

Let's find out first. what version of firmware is installed in the instrument panel. The first numbers (2190 or 2192) indicate the car model (Granta or Kalina 2). This is followed by the numbers 00, 20 or 40, which stand for “standard”, “norm” or “lux”, respectively.

Firmware versions of Lada Granta and Kalina 2 instrument panels

The table was compiled (is in the process of being adjusted) based on reviews from car enthusiasts (please add comments). There is no guarantee that all data is correct!

What is needed for firmware

Changing the display and working with a soldering iron

Reworking with a soldering iron

If you don’t want to use the modified firmware 2190-20_092_for_076, then you can modify it with a soldering iron.

Photo by goffka. Author of the idea is destin.

Point one - The airbag indicator will stop lighting! The easiest way is to do it this way.

The track came out from one exit, the processor leg was unsoldered from it and lifted into the air. The required leg was soldered to the track, which was also hanging in the air.

The idea is great, but there is a small problem: this output is reassigned to the control input for the emergency lights indication. And in the future we may need it, so I decided to go a different way, or rather, I spied another option from the same author as in the previous photo.

And this is how it happened:

You just need to cut the track so that it doesn’t go back to the other leg of the processor. The photo shows what needs to be cut.

Point two - Illumination of instrument scales. Here, too, you need to solder to another output, but this is easier. Solder the resistor.

It turns out that the track is broken, we leave the side of the track that goes to the controller hanging in the air, and solder a wire to the second edge and lead it here

Here there is also a path from the controller to turn on the rest of the lighting, and we’ll parallelize it. Solder the soldered resistor and the wire to it.

Please note that my resistor goes above the track, one end is soldered to it, but the other is not!

Let us remind you that there are other improvements to the dashboard, for example, installing a PTF indication. In the comments, indicate successful options for firmware updates, we will supplement the table in the article!

Photo: MrRararai in-flight magazine

Keywords: instrument panel Lada Granta | dashboard of Lada Kalina

0 0 0 0 0 0

Share on social networks:

Do-it-yourself dashboard overexposure

You will need: remove and disassemble the instrument cluster, SMD LEDs (unsoldered from LED strip or LED lamp), soldering iron.

The process of replacing LEDs on the instrument panel board consists of unsoldering the standard SMD LED and soldering a new one in its place. During such tuning, there are several important points to consider:

1. take your time so as not to damage the conductive traces of the board;
2. observe the polarity (SMD LEDs have a bevel on one side, install a new LED in the same position);
3. do not overheat the LEDs; high temperatures may cause them to fail;

After soldering the required LEDs, it is recommended to check the backlight. To connect the instrument cluster at home, you need to apply +12V to pins 19 and 21, and ground to 17. You can also verify that the installed LEDs are working properly using a multimeter in “tester” mode, connecting the probes to the LED according to the polarity (red probe is plus) :

If all LEDs are installed successfully, reassemble in the reverse order. Relighting the instrument cluster of Grants or Kalinas is a great way to make your car more individual and stylish. It is noteworthy that there are a lot of options for implementing such panel tuning, but which style suits you best? Participate in the survey, share video materials and photos of your improvements.

Let us remind you that the website presents other modifications to the instrument panel, for example, you can reflash it and install an outside air temperature sensor.

Direct firmware mms 2190 grant

The firmware process is quite simple! All you need is an SD card. Note! The SD card must be formatted in FAT16. A common problem after flashing the firmware is the Lada logo freezing on the monitor of the standard multimedia system. This problem may occur as a result of:

• Failure to comply with the parameters of the required formatting system; • Old SD card model, different from SDHC.

If a problem of this kind arises, then it is necessary to check compliance with the above two points of the procedure for flashing multimedia firmware on the Lada Granta.

After the flash drive is formatted and the new software has been decided, for example, NewMenu V7.391Nitro, you need to download the new firmware NewMenu V7.391Nitro and unpack it directly onto the SD card itself.

As for the FirmWare folder, the files located in it must be moved to the root of the SD card. The root of the SD card implies placement of files in addition to other moved folders.

The copying process is complete, which means it’s time to remove the flash drive from the computer. It is worth noting the need for mandatory safe removal, which has long been known to all PC users.

An SD card with files placed on it must be inserted into the mms. After the removable media is inserted into the mms, it must be turned on. After waiting for the device to fully boot, long pressing the volume key will reboot it.

The reboot takes place in four stages, which is shown in the example of four boot lines, upon completion of which, MMS will start in normal mode (standard display menu). Just a few seconds after the standard menu, the radio will go to the altmenu.

For diagnostics, reading indicators and errors, ELM327 automotive scanners are used. They also use other multi-brand devices that have the ability to diagnose body electronics, airbags, etc. They also work using the OBD2 protocol with a CAN bus:

As mentioned at the beginning of the article, Granta received new “brains” with CAN support (M74CAN). This innovation is capable of integrating “brains” with alarms and radios with a CAN bus.

They often install a “Standard” controller with Itelma number 11186-1411020-22: This ECU is not compatible with earlier VAZ models. In early VAZs, for example, Priora, the ECU came with a K-channel for data transmission.

Location of the ECU for Granta:

The “brains” are located at the bottom of the front panel, or rather under the glove compartment. It will be better visible if viewed from the passenger seat. The ECU is hidden by sound insulation and upholstery, so it will not be easy to get it out.

Flaws

In addition to a wide range of advantages, the digital panel for Lada Granta FL has a number of disadvantages:

• when the distant color is turned on briefly, the panel changes the mode to “night”;
• when the ignition is turned on, there may be malfunctions in the indication of the performance of the ESD, ABS and airbags;
• When you turn off the ignition, the digital display may go out for a few seconds.

When temperature changes occur, incorrect values ​​may appear in the readings of the oil pressure sensors, battery voltage at idle and transmission oil temperature in the automatic transmission.

Instructions for flashing the dashboard firmware

Remove the instrument panel and rear cover. Usbdm OSBDM V4.95 programmer (when purchased, the kit includes a disk from which we install the HCS12 Programmer and USBDM driver software). For Windows 8 or 8.1, driver authentication must be disabled before installing the software. After installing the software, connect the programmer to the PC (the COM and USB lamps should be on).

Connect to the device:

• power supply (9-14 V) on pins 19 and 21 (you can do it without power, to do this, move the jumper under the programmer cover to 3.3v);
• minus on pin 17;
• programmer cable (the PWR lamp will light up).

Launch the HCS12 Programmer software and make the settings:

• On the Interface tab, click detect. USBDM-js16-001 will appear in the window. The bottom checkboxes must be activated;
• On the Target tab, click on the Load Hex Files button and select the firmware (must be in the root of the disk), check the box Auto Reload. select the HY-MC9S12HY64 chip. select Unsecure. select EraseSelective and check the box Enable Sounds. (to reset the mileage and erase the immo, select EraseMass, but this is not recommended);
• On the Advanced tab, check the Enabled checkbox and check the field below (there should be a letter F at the end, if there is another letter, then change it to F).

When all the parameters are set, we start the process of flashing the instrument panel (on the Target tab, click Program Flash). After 10 seconds, the update will be completed; when asked about connecting the next device, answer “No”. We check the version of the instrument panel again. All!

Instructions for flashing the dashboard firmware

Required

: Usbdm OSBDM V4.95 programmer (available in the Aliexpress catalog).

Install the HCS12 Programmer software and USBDM driver X86 or X64. For Windows 8 or 8.1, driver authentication must be disabled before installing the software. After installing the software, connect the programmer to the PC (the COM and USB lamps should be on).

Connect to the device

:

• remove the instrument panel and rear cover;
• power supply (9-14 V) on pins 19 and 21 (you can do it without power, to do this, move the jumper under the programmer cover to 3.3v);
• minus on pin 17;
• programmer cable (the PWR lamp will light up).

Launch the HCS12 Programmer software and make the settings:

• On the Interface click detect , USBDM-js16-001 . The bottom checkboxes must be activated;
• On the Target , click on the Load Hex Files and select the firmware (must be in the root of the disk), check the Auto Reload , select the HY-MC9S12HY64 , select Unsecure , select EraseSelective and check the Enable Sounds . (to reset the mileage and erase the immo, select EraseMass, but this is not recommended);
• On the Advanced , check the Enabled and check the field below (there should be a letter F at the end, if there is another letter, then change it to F).

Nuances of multimedia firmware Grants (2190)

It is quite easy to carry out the firmware itself when installing the mms 2190 firmware. To do this, it will be necessary to use an SD card.

Let's concentrate! This card is subject to mandatory and preliminary formatting using the “FAT16” version.

Among the common flaws that occur after the dashboard firmware is installed, even if it is the latest version, is the Lada logo freezing on the display of the head unit.

This moment can be provoked by the following factors:

• failure to comply with required formatting principles;
• the presence of an outdated version of the SD card that differs from “SDHC”.

After successfully formatting the card and selecting software (for example, “New Menu V7.391 Nitro”), you will need to acquire the latest firmware and unpack the product onto a previously prepared SD media.

Regarding the “Firm Ware” folder, note: the files located in it will need to be redirected to the root directory of the card itself. Upon completion of the copying process, disconnect the flash card from the PC, not forgetting about the safe removal technique.

How to set up "GPS" on the firmware version of the multimedia?

Carrying out this action will not take much effort. The procedure involves preliminary switching with the GPS module and consists of the following algorithm of actions:

• go to the corresponding “Tools” menu;
• activating the display keyboard;
• direct module switching;
• route instructions: “\staticstore\dll\232usb.dll”;
• continuously pressing the “OK” key after the prompt regarding driver selection is displayed on the screen.

If the indicated steps are completed correctly, then we proceed to the manipulations of setting up the navigation software. In the program, we select the “COM 5” port and the corresponding speed – 4800 bps.

Upon completion of the entire list of manipulations, we observe the operation of the system

Please pay attention to the presence of the configured Navitel program

Possible faults

If everything is clear with the description, then let’s move on to the malfunctions. Like any other electronic component, the Lada Granta instrument panel is also susceptible to various malfunctions.

What kind of breakdowns can occur in the operation of the control panel:

1. The tidy is broken. If the shield fails, there can be quite a lot of symptoms. For example, only some or all of the devices will refuse to work. If this is the case, then the problem in this case may lie either in the power supply of the device or in its board. It is better to entrust repair problems to specialists.
2. The tidy is glitchy. For example, all doors are closed and the unlocked door indicator is on, or the optics are not turned on, but the corresponding light on the dashboard is flashing. As a rule, in this case the problem lies precisely in the board (of course, if the sensors are working). If the problem is in the board, then flashing the dashboard firmware can solve it, but this option does not always help. It is possible that the electrical equipment lights are on on the dashboard due to a faulty sensor, so it would be a good idea to check its functionality.
3. All devices work, but there is no backlight. If all the backlight bulbs do not work at once, then most likely the problem lies in a blown fuse or a damaged wire or connector. Checking the wiring is done using a multimeter.
4. Only part of the light bulbs or one of them does not work. In this case, the malfunction consists of a burnt-out lamp; to eliminate it, the instrument panel in the Lada Granta is dismantled, after which the burnt-out lamps in it are replaced.
5. The equipment indicator on the dashboard does not turn on. For example, you turn on the high beams, but the corresponding light does not light up. This may be due either to a failure of the indicator itself (the lamp is changed in the same way), or to a breakdown of the sensor. It is quite possible that there is poor contact between the light bulb and the wiring.
6. Speedometer failure. The cause of the malfunction may lie in the board or speed sensor installed on the device. The situation is similar with sensors - fuel level, engine temperature. If they do not work or show incorrect values, then the problem should be looked for in the controllers themselves, wiring or board. It is possible that the devices are not working simply due to poor contact.

Other (spare parts, maintenance) Lada Vesta

Products from the Dustershop77 range on the topic of the article: