Priora 2 installation of a 2din radio instead of an on-board computer

Connection diagram

The factory connection diagram does not provide for the supply of positive power through the contact plates of the ignition switch (red cable). To ensure correct operation of the device, it is necessary to remove an additional cable from the circuit, which is energized only when the ignition is turned on. The line must be protected by a fuse rated at least 15 A (for example, a cigarette lighter circuit).

An additional signal, ensuring the safety of the settings when the car is stationary, is supplied using a wire with a yellow insulator. The cable is routed to a circuit connected to the positive terminal of the battery. There is also a ground connection in the power circuit. The power and speaker cables are routed into the instrument panel; to connect the head unit, you will need an ISO standard adapter.

Connecting the amplifier to the radio via the mini-ISO connector

To implement this amplifier connection scheme, you will need to find a mini-ISO connector, which should be connected to an empty slot on the back of the standard radio of Lada cars.

It is further recommended to use high quality shielded wires.

The main advantage of this connection scheme is high sound quality.

How to install the device itself

The radio is installed in the Priora in a standard socket designed for mounting a 1 Din standard holder. The metal shaft is inserted into a rectangular hole, and then secured using metal antennae, which are bent with a screwdriver. Then the owner connects the cables and antenna, and then installs the head unit housing into the shaft until the side spring clamps are activated. Installation work is completed with the installation of a decorative plastic frame and front panel, then the equipment is tested.

Are you a car driver?! Then you can take this simple test and find out. Go to test »

To integrate a 2-Din radio into the Lada Priora, you will need to modify the car's design:

Remove the battery from the car, and then carefully separate the plastic cover with air channels located in the center of the dashboard. The part is held in place by plastic clips; a mounting spatula is used for removal. Together with the cover, the connecting cables are removed and attached to the back of the cover.
Disconnect the plugs from the retaining pads (located on the back of the small items drawer), and then connect the media player adapter.
Connect the adapter to the radio and output an additional power cord (for the red wire).
Restore power to the vehicle's on-board network and check the correct operation of additional equipment at different positions of the key in the lock.
Cut a window in the plastic cover that matches the dimensions of the multimedia center body. A hacksaw is used for cutting; the edges are finished using a file.
Insert a metal clip, which is fixed by bending the triangular antennae.
Install the trim in its original place, passing the wiring harness through the mounting shaft into the car interior. If the machine does not have an antenna, then it is necessary to mount the device and lay a separate coaxial cable. The cord is routed through the upper part of the cabin under the pillar trims and the headliner. It is not recommended to lay the cable along the floor of the cabin, since passengers will touch the wiring with their feet.
If the head unit design uses a rear USB connector, the plug can be installed in the glove box or on the surface of the center console.
Reinstall all the removed parts, and then check the operation of the radio.

If you plan to replace the standard radio in a Priora 2 car (manufactured after 2003), then remove the gearshift lever cover, which will allow you to unscrew the screws securing the trim (additional screws are located in the niche of the cup holder). The central cover is secured with screws located under the radio socket plug, the switch block and the cup holder niche. After removing the standard plastic pocket, it is necessary to secure the player's mounting shaft to the panel frame; the antenna cable is pulled out from the niche under the glove compartment.

How to properly remove a radio without special keys

Many motorists face the problem of removing the radio in their car. Some people cannot remove the standard device installed at the factory, others inherited the music along with the car, and others simply lost special keys. There are also plenty of reasons for dismantling - from repairing wiring to buying a new stereo system. Hence the demand for information arose on how and with what help you can carefully remove the car radio without damaging the plastic of the front panel. And although the operation is primitively simple and can be easily performed with improvised means, there are pitfalls in it that you need to be aware of.

Useful tips

Since the ignition switch in Lada Priora cars does not control the power supply to the radio, it is permissible to install a manual switch. The power cable, equipped with a red insulator, is connected to a button that is mounted on the instrument panel or center console. If a 2-DIN device with support for a rear view camera is mounted, then the housing with the lens is installed on the handle of the luggage compartment lid.

The cable is routed through the hole in the license plate light. The position of the video camera is adjusted using a flexible metal bracket or spacers. The equipment is connected to the on-board network through the reversing lights; the image is displayed only when the car is moving in reverse.

The VAZ plant equipped some of the Priora cars produced with a standard head unit; the basic modifications were only prepared for independent installation of equipment. The mounting sockets are designed for standard products; it is possible to install a 2-din radio in a first-generation Priora, but this requires modification of the internal elements of the instrument panel.

When installing a car radio, it is useful to know

During the process of installing and connecting a radio in a car, non-standard situations often arise that cannot be foreseen in any instructions.

So, if you use a standard car antenna when installing a car radio, then sometimes the length of its wire may not be enough. Many cars are still equipped with antennas designed to install old-style radios. Their antenna socket is located on a “tail” that is only about fifteen centimeters long.

In this case, you can try to connect the antenna blindly after connecting all other wires to the radio. If this fails, then, most likely, you will have to remove the console and insert the antenna plug by touch after installing the car radio in the container.

By the way, after about half an hour of this “Kama Sutra” you will probably begin to think about buying a new car radio antenna.

If it becomes necessary to remove a car radio with a removable front panel from the container, you will need to insert two flat keys included with the radio onto the sides of it until they stop. But before that, do not forget to remove the front control panel - it is usually detached with the “Release” button.

Installation on the first generation Priora

To install the car radio in its original location, you need:

Disconnect the battery from the vehicle's on-board network.
Remove the 1DIN decorative frame with a box for small items from the center console of the instrument panel. The assembly is held in place by plastic latches located in pairs at the top and bottom of the drawer. Removal is carried out by pulling the part towards you; it is possible to bend the edges with a plastic mounting spatula.
The rear has mounting points for the factory patch harness equipped with ISO connectors. It is necessary to disconnect the plugs from the box, which is then set aside.
Connect the pads to the radio and check the operation of the device. Priora cars are supplied from the factory with a constant supply of positive power, independent of the position of the key in the ignition switch. It is necessary to change the wire connection, following the operating instructions for the head unit. The positive signal sent when the ignition is turned on is taken from the rear window heating button.
Lay the wire leading to the external antenna. The cable runs under the plastic trim of the A-pillars and the roof panel. To reduce the likelihood of noise, the wire is wrapped in fabric insulating tape or foam rubber.
Reinstall the removed trim elements.
Connect the antenna power from the ISO connector and check the functionality of the acoustic device in radio receiver mode.
Place the standard mounting shaft into the hole in the center console. The part is attached using tabs that are pressed out with a screwdriver. During installation, it is necessary to ensure maximum fit density, which will reduce vibrations of the radio when moving.
Connect the power, speaker and antenna plugs to the connectors on the back of the head unit. Place the radio in the guide shaft until the locking latches engage. Check the tightness of the installation, and then place the decorative frame in place.

To install a 2 DIN radio you will need:

Remove the front trim of the instrument panel along with the central air ducts.
Cut the connecting jumper between the standard socket for the radio and the plug. Expand the rectangular hole to the dimensions specified in the technical documentation for the head unit.
Using a saw, modify the plastic frame inside the instrument panel.
Place metal guide slides in the resulting window on the front trim and secure them by bending the triangular fasteners.
Reinstall the removed parts, and then connect the new head unit and insert it into the guide shaft.
Check the functionality of the equipment, configure the radio receiver and loudspeakers.
Install a decorative frame located around the perimeter of the front panel of the radio.

The process of installing and connecting a car radio

The installation process for car radios of different types and manufacturers is not much different from each other. To do this, the container without a radio is installed in a standard socket and fixed by bending outward the metal petals along its perimeter.

In modern cars, a special ISO standard connector is provided for connecting the car radio. The whole connection in this case comes down to the fact that you will need to insert the connecting block of the car radio into the corresponding ISO connector of your car.
In older cars, as well as in many domestic cars, the ISO connector is not provided by design. To install a car radio in this case, you will have to purchase the appropriate connector and connect it yourself. Fortunately, the wires on such connectors are usually marked and signed.

Let's move on to connecting the car radio wires to the ISO connector. Take a look at the connection diagram below. As can be seen from the diagram, the left side of the ISO connector is responsible for powering and controlling the radio, and the right side is for connecting speakers to it.

Typical connection diagram for a car radio
The main step in connecting a car radio is connecting the power. It is at this stage that most mistakes are made.

Power is connected to the car radio through a separate fuse using a flexible stranded wire with a cross-section of at least 3 mm 2. In most cases, it will be enough to use a 10 ampere fuse; it will reliably protect the power circuit from emergency situations.

The radio is powered through three wires: yellow, red and black.

+12 V (yellow) – main power wire. It powers the built-in amplifier and also serves to save car radio settings. This wire is connected through a fuse directly to the battery. It is advisable that the length of the wire from the battery to the fuse does not exceed 30 cm.

ACC (red) – control of turning on the car radio from the ignition switch. On many vehicles, the ignition switches have an ACC (accessory) position. When you turn the key to the ACC position, power is supplied to the car radio, interior heater and cigarette lighter socket, but the car's ignition system is de-energized.

GND (black) – connects to the negative terminal of the battery. But this is ideal. Due to the low power of the car radio, it is allowed to connect the black wire to the car body. You must first ensure good contact with the body by cleaning the joint from dirt and oxides. You can also use contact lubricant to protect them from oxidation.

Installation in Lada Priora 2

Priora 2 cars are equipped with a standard 1 DIN size radio with a trapezoidal front part. The display is located on the top of the instrument panel, which makes it easier to read information.

Basic configurations were not equipped with a head unit; plastic plugs were installed on the central part of the instrument panel.

The instrument panel has a standard harness for connecting the radio, equipped with an ISO connector consisting of two plugs.

Self-installation of the radio on Priora 2 includes several stages:

Unscrew a couple of screws located under the removable rubber mat in the niche for small items.
Remove the decorative leather cover of the gear selector knob, under which there are 3 additional screws for a Phillips screwdriver.
Remove the lower part of the center console; the gear shift knob remains in its original place.
Unscrew a pair of screws located under the climate control unit.
Use a spatula to pry and remove the 2 covers located above the button block and under the standard place for the radio.
Unscrew the remaining 4 screws and pull the front panel towards you.
After this, it is necessary to modify the panel or mount the equipment in a standard window and make adjustments.

The radio installed on the Priora must be connected through the ignition switch, which allows you to save settings and guarantees that the equipment is turned off after removing the key. It is necessary to modify the standard plugs by supplying additional power from the buttons in the instrument panel.

The new generation of Lada Priora cars is equipped with a more modern dashboard, which provides a standard place for placing a multimedia system or on-board computer. This design feature is actively used by some car enthusiasts when making modifications. We are talking about installing a tablet in Priora.

This solution allows you to significantly expand the functionality of the multimedia system, using the device as a navigator, on-board computer, or monitor. Listen to music, watch movies, the possibilities are almost endless. For installation, you can use a device from any manufacturer, but you should remember that products with a screen diagonal of 7 inches are most suitable.

Removing the device using standard keys according to the instructions

So, there is a radio and standard keys. But that's not all, you will need an additional tool in the process.

Required Tools

To work you will need:

Keys for dismantling. Depending on the specific model and key manufacturer, there may be 2 or 4;
Knife.

Sequence of removing the car radio from the niche

First of all, remove the front panel, and if necessary, then the decorative parts. On older models, this frame covers the key connectors. This is no longer the case with the new ones.

Then the holes for the keys become visible and easy access to them is provided. The holes can be seen on the side walls of the head unit.

Then the keys are inserted into special grooves - they need to be inserted until they click. In some cases, it may be necessary to force or rock the fixture from side to side. If a click occurs. You can safely pull the radio out of the mine.

If the head unit cannot be removed, it can be screwed to the panel with an additional pin. In this case, it is necessary to remove the dashboard to access the device from the back side.

Video

The video shows in detail the entire process of dismantling the car radio using standard keys.

Do-it-yourself installation of a radio in a Lada Granta

This article will discuss how to install a radio on a Lada Granta car. I would immediately like to say about the electrical connection of the radio. AvtoVAZ has made a significant step forward.

Now, when installing a radio, there is no need to run wires to power the radio and speakers; all this is included in the standard audio preparation of the car.

This is a big plus if you remember the tenth family, when the owners of tens and twelves had to do everything from A to Z, everything themselves.

Dimensions of the radio for installation in a regular place in the Lada Granta

The space for installing a radio in the dashboard console of a Lada Granta car is designed for 1 DIN radio. Here is an example of installing such a radio.

When installing a 2 DIN radio, you will need to cut the partition up and adjust the frame in the console to the size of your audio system, which will make your life somewhat more difficult

Operations for connecting a radio to a Lada Granta

The first thing you need to do is remove the plastic pocket installed in place of the future radio. To do this you will need a flat blade screwdriver. Having taken out the pocket, on the reverse side you will find slots where ISO connectors will be inserted to connect the radio.

You can learn more about them from the article “How to connect a radio with your own hands.” The connectors fit quite securely into pockets, meaning you don’t have to look for them in the wilds of the panel to make connections. Now you need to remove the metal frame from the radio and install it in the place where the plastic pocket was. Unbend the frame's antennae to lock it securely in place.

When installing the radio, you will not need any tool to change the shape of the holes (a file, a file), all dimensions have already been made in accordance with generally accepted standards for 1 DIN radio casings.

Installing speakers in the standard places of the front doors on the Lada Granta

In addition to the radio, for its normal operation, it will also be necessary to install speakers and acoustics in the car door.

To cut holes in the door trim, it is better to remove it from the car.

To do this, you need to dismantle the door handle, the plastic casing in which the door opening lever is installed, and the glass position adjustment handle (if you have a standard package).

See the article “Removing and installing door trim on the Lada Granta.” The door trim and metal frame of the front doors provide a size for 16 cm speakers.

In this case, the hole in the door frame is slightly larger and you will have to increase the plane from the mounting “ears” of the speaker to the mounting holes in the door; - If you decide to install 16 cm speakers, then you may have to modify the door frame here, since the speaker basket can It definitely won’t fit into the standard hole in the door hardware.

You will need a grinder or a jigsaw with metal files. We cut a hole of the required diameter and try on the speaker.

We connect the speaker and install it in place. We install door trim. We mount the frame for the metal grille of the speaker and, accordingly, firmly fasten the speaker to the door with 4 self-tapping screws. We install the speaker grille.

In addition, you may find the material from the article “Wiring diagrams of the Lada Granta” useful, which shows the blocks for connecting the radio power supply and connecting the speaker wires to it, blocks 17 and 18.

The “standard” configuration also includes wires leading to the speakers of the front doors of the car. So, the connection of the radio speakers in the doors is carried out through the rear harness, see the article “Wiring diagram of the rear wiring harness of the Lada Granta”, contacts on the block 16,17,18,19.

Pinout of contacts of the head unit priors

A	B	C
1-SCV	1-Speaker RR+	1-line output LR	11-AUX IN
2-TEL MUTE	2-Speaker RR-	2-line output RR	12-AUX GND
3-Speaker RF+	3-GND line outputs	13-CD BUS *
4-BAT+	4-RF Speaker-	4-line LF output	14-
5-Control ant.	5-Speaker LF+	5-line RF output	15-CD BUS GND *
6-Backlight	6-Speaker LF-	6-12V	16-A+ CD *
7-A+	7-Speaker LR+	7-RXD	17-U+ CD *
8-GND	8-Speaker LR-	8-TXD	18-CD-NF GND *
9-GND	19-CD-NF LEFT *
10-line subwoofer output	20-CD-NF RIGHT *

* Pins 13-20 of connector “C” are used to connect the CD Changer

Options for installing a tablet in Priora

There are several options for installing a tablet in Priora 2:

In the first situation, installation occurs much faster than in the second case. However, a significant disadvantage is that the tablet battery, when exposed to sub-zero temperatures in winter, will quickly lose its capacity or even fail. In addition, there is a possibility that in the hot season, when the car interior heats up, the battery may ignite (remember the story with tablet computers and spontaneous combustion of Samsung batteries). As a result, the car can burn out completely.

The second option involves independently modifying the tablet and resoldering some contacts. The point is that the tablet is powered directly from the battery in the car, so it can be turned on and off at any time, regardless of whether the radio is active or not. This approach provides a number of advantages, but it is more complex in implementation than the first, above-mentioned approach.

Which option to use - decide for yourself, it all depends on the level of preparation and the desire to delve into the essence of the issue in detail.

Why bluetooth doesn't work

Most often, failure occurs due to the fault of Sony smartphones. We have already looked at how to connect bluetooth to the Lada Vesta, so it’s worth trying the pairing again.

Connection may not be possible when the Bluetooth function in Vesta is not activated in the radio. Press the button to accept the call, the system begins to function. If this does not resolve the problem, it is best to contact your dealer. Also, this problem may appear after trying to connect several phones. There may be other reasons why Bluetooth does not work on Vesta, including a factory defect.

Which tablet to put in Priora 2

As mentioned above, the main and basic requirement for a tablet computer is the size of its screen. In our case, this figure should be 7 inches. If we talk about specific device models, the most popular of them are:

The second requirement for the device is the ability to recharge it using a standard USB cord. The third, but important parameter is the quality of the device’s battery. Please note that when installed in a car, the battery of a mobile device will be subject to aggressive external influences in the form of heat or cold, and temperature changes.

Lada Priora Hatchback Luxury › Logbook › 2din in Priora 2 + console from 1st + Infinity watch

Hi all! Today I’ll tell you about someone’s multimedia update in Priora. Before this post, I already had a KONNWEI RK-701 radio tape recorder on Android 5.1; in general, the radio tape recorder was not bad; it then cost me 7,031.73 rubles. But there were a number of problems with it. 1. It was impossible to install Yandex navigator in the play market, it said your device is not supported. and accordingly, you can install it manually via APK, but there were problems downloading updates. Later I installed Yandexmarket and the problem was solved. 2. These are mechanical buttons on the front panel, the back button died after 2 weeks of use. Of course, I didn’t bother to repair it. 3. This hardware has a 2 core processor and 1 GB of RAM is not enough. I can’t install many applications because navigation alone consumed 350MB of RAM. 4. Android glitches in video mode when scrolling through the media library, the application periodically closed, which was wildly infuriating. 5. The GU settings menu was almost in engineering mode with a special password 66668888, which I found. ——————————————————————————————————————————————- But overall a good device for their money. —————————————————————————————————————————————- And so this device I I sold it for 6500, and started looking for something new without mechanical buttons and with better hardware. In general, from the burning goods I managed to snatch a super radio bosion BX-412, you can just say for nothing 7,965.88 rubles and so the config: 4-core percent 2gb RAM! CHARLES! although I ordered from 1st I just felt better. A full-fledged DVD, you can now even sing karaoke in the car))) there is an additional output for an external microphone. Android 6.0 is a very fast thing and does not bug like 5.1, and there is all the output for 2 additional monitors and 2 video cameras. In addition, they sent me a video camera included in the kit, which was also not in the description. functionally there is everything except TV ————————————————————————————————————————- from the minuses of Android 6.0 1. Navitel pirated does not work, when you click install it says that installation information was not found. now Yandex navigator is supported) 2. there is no multitasking like on 5.1, i.e. when playing a video, when you press the back button, the video was played in a minimized state and you could additionally open the navigation and look at the monitor with the map. 3. Immediately when you press the back button, the video closes and only maps work. not convenient. 4.but the minimized navigation works when the video is on. Convenient setup menu. but now you can’t add your own logo; on 5.1 this could be done. 5. When the engine starts, the radio reboots due to a voltage surge. On 5.1 this was not the case at all; the capacitor was soldered to the power supply. ————————————————————————————————————————————— As a result, the slide from the old radio was not They arrived and it was installed somehow on a temporary basis. Buying 2 din skids is quite a problem. I bought ACV full last time. they are already radio tape recorders. ===================================================== ========================

The post was written: September 26, 2022.

It's been a long time since I finally got around to installing it properly. I bought extra. frame for GU Car 2 DIN 178 mm * 100 mm 1,135.28 rubles Because in our city I couldn’t find anything suitable for a price up to 1,500 rubles. plus I took a new center console for 300 rubles, because the stock one was cut crookedly and with the melting it didn’t look like a fountain. On the new console, I already understood what and where to cut. And so to put the console from Priora 1 into Priora 2 You need to: Saw off from the top somewhere

4mm and along the edges in the same area from the top

6mm. this was done by fitting, removed and installed 15 times. ——————————————— Additionally, shorten the upper air duct-deflector by about 5mm as well. because if you leave it as is, the console sticks out about 7mm and does not fit flush with the torpedo. I sawed the bur by eye with a machine. Then on a plate with sandpaper I leveled the planes into a mirror. Next, I cut out a hole for the clock to install the Infinity clock on the Priora and began to cut out a window for 2din because the standard frame comes with a narrower one. I had to completely cut out the pocket in the trim as it was not necessary because the 2-din frame fit only 2cm deep. Well, installation. We install the standard console with 4 screws, insert the 2din slides and install the radio, voila and you're done. You can see about the installation of a second monitor in the place of the bk here. Also, who is interested in installing a 3rd monitor between the seats of a BMW style Prior? In terms of acoustics, we will finally install 16cm Bose speakers from W220 and 2 Alpine type r10 subwoofers in a circle. And also 4 video cameras (all-round view)

How to remove the standard

Removing the standard radio on a Priora is carried out without disassembling the console and decorative frame. The tool is inserted between buttons 2-3 and 5-6 or under the Skan and TA keys, depending on the model of the head unit. When the ends of the keys or plates rest against the latch, a characteristic click will be heard, indicating that the lock has disengaged. After this, the keys are moved apart and the tape recorder is pulled out. In some cases, the device cannot be removed this way.

Then, using 1 key on the right side, disengage the latch, and with the other hand, push the tape recorder out through the glove box. When one side moves out of place by 2-3 mm, press the left latch and pull out the car radio. It will be impossible to completely remove the device, since it is held in place by the antenna wire. To do this, you need to cut off the plastic tie under the dashboard from the glove box. After this, the GI can be completely removed. To replace the MMC, you need to disconnect 2 connectors from the back - the power connector and the output to the car speakers.

In some cases, to dismantle the landing body it is necessary to remove the decorative panel. To do this, unscrew the mounting screws under the air conditioning controls and the 2 upper fastening elements, and then remove the cover from the gear shift knob. If a 1-DIN version is installed instead of a standard car radio, then it is necessary to install a decorative frame that will cover the remaining hole.

Lada Priora Sedan › Logbook › ♛ Tablet instead of BC Priora 2 SE sedan ♛

Hello!))) Well, my hands have also reached these changes. The regular BC was an eyesore, and it was of no use “like milk from a goat.” I looked at a lot of reviews, visited a certain number of pages of our Drivers (by the way, I grabbed information from different places, there were a lot of questions, but in one blog I didn’t find answers to all my questions, I had to look through many pages, so, I’ll try to answer all your questions in advance in this post... Look at the photos, videos, read the text and you’ll understand everything ...).Then one fine morning, and as you know, everything always happens “one fine morning” for me = D... I went to buy a tablet. I bought a budget one, I think for a while, the Prestigio wize 3067 3G model. DIMENSIONS 188 × 12.5 × 109 mm (what you need))). Possibility to install a SIM (which is very important for me), Flash card up to 16GB. Cost 2 thousand rubles. I bought it used, but in perfect condition (it was given to the old owner and it was lying around idle). And so the price, if I'm not mistaken, is from 3 thousand rubles. for a new one.

Dismantling a standard music center

Often, standard head units (aka radios) are removed using the method described above, since they are attached to 2 or 4 clips. For example, the factory player on a Lada Priora car is held on by two latches, and to unlock them, thin steel strips must be inserted between pairs of radio channel switching buttons “2” - “3” and “5” - “6”.

Advice. Before you start disassembling the factory radio, find out about the method of its fastening, so as not to poke the pieces of hardware at random if you do not find technological openings.

In Priora, stripes must be inserted between the buttons

To remove car radios that are fastened with screws, you need to prepare a simple set of tools:

thin flat screwdriver or knife;
Phillips screwdriver;
set of small sockets (from 6 to 10 mm).

With this mounting option, the factory turntable must be unscrewed using the heads

On different brands of cars, standard players can be mounted in different ways, but the principle is approximately the same: the device is screwed to brackets that are covered from the outside with a plastic lining. As an example, we propose to consider removing the radio on a Korean Hyundai Solaris car, performed in the following order:

Use a flat-head screwdriver or knife to pry up the lower corner of the plastic decorative panel framing the stereo. Pull the edge and grab it with your hand.
Gently pull it towards you and release the first latch, and then move around and unlock the rest.
Holding the panel with both hands, remove it and, if necessary, disconnect the connectors located at the bottom.
Unscrew the 4 mounting screws with a Phillips screwdriver and pull out the radio.

Factory car radio Hyundai Solaris

Advice. When dismantling any player, do not rush to disconnect the battery from the on-board network, since the device will power down in 10-15 minutes. It may be blocked and the next time you turn it on, it will require you to enter a security code that you do not have.

Lada Priora Hatchback SOCHI › Logbook › Screen on the center console

For about a year and a half now, the thought of installing some kind of multimedia installation on the center console has not left me. All this time I was looking for the most suitable option in terms of functionality, price, reliability and ease of installation. In my opinion, a multimedia system in a car must have several properties:

1. Playing music files + radio 2. Availability of navigation 3. Possibility of connecting a rear view camera 4. Bluetooth and with normal Hands Free 5. NOT MANDATORY, BUT... the ability to play video files

From the first five points, it is logical to assume the sixth point - the presence of a screen, optimally 7 inches.

Just as I think, if you have navigation and a rear view camera, the installation height of the monitor relative to the driver’s eyes is important.

The central console of the Priora (pre-restyling) was originally designed for a single-din balalaika, so the height of its location in the console did not matter. During the reystaling, this problem was solved by installing the monitor as high as possible, on the dashboard itself.

Based on all this, I obtained the following configurations throughout operation. The very first option was - Galaxy tab II tablet or my assistant on the road - part 1.

The advantages of this arrangement were ease of viewing, a navigator, a recorder, various multimedia... But the disadvantages of such an installation were more significant for me: firstly, a regular tablet is not intended for installation in a car and sooner or later it will fail due to heat or cold, -secondly, it is a bait for thieves. Thirdly, Android is quite difficult to make friends with a rear view camera ((Yes, yes, I have EasyCAP, and it even somehow worked, but all these delays, crashes and image glitches... Well, the last minus for me is that I didn’t find a way raise hands free on android((

About a year ago I thought about this installation: Remaking the center console for two monitors. Of course, I would like to have two monitors (the main mafon and a tablet) as close and as high as possible, but... This would involve major alterations: either sawing the floor of the dashboard, or removing the central air ducts. But I like universal solutions, so that if you don’t like it, you can return everything as before)))

We also considered solutions such as Parrot Asteroid, everything seems to be great, but the price, 5-inch screen, and generally there is little information on it.

Another option was ali. Where are we without the Chinese)) As it turns out, they have options for Android navigators with an AV IN input, but... Again, there is no hands free, although there is an input for the camera, the image is transmitted jerkily, well, not that...

All these considerations led me to the conclusion that the most suitable option for me would be to install a standard MMC Kalina-2/Priora radio.

Exactly hers, with a separate screen. It will all look something like this:

The radio itself has already been ordered, as soon as I install everything, there will be a detailed report. By the way, I have never seen this option anywhere, we will be pioneers. And if someone has already done this and I missed it, please let me know...

I also wanted to write about acoustics, but there’s a lot of text, then in the next post...

I thank everyone who finished reading the multi-book, maybe someone will take note of something from this article.

Tuning

How can I set up my radio to receive calls from my phone?

A special feature of the installation is the ability to communicate between the radio and the telephone. This function is available through the existing Bluetooth system. Connecting a mobile phone to the system is not difficult. The work takes about 10 minutes, and it is performed according to the following scheme:

1. Bluetooth is activated on the mobile device.

2. On the radio panel, press the button with the handset (left or right).

3. After the device name is displayed on the radio screen, you need to connect by pressing the confirmation button on the mobile phone itself and entering the code “0000”.

4. The PIN code is changed by pressing the Scan button on the radio, entering a new combination and confirming using button 8.

5. To make a call, enter the subscriber’s name on the numeric keypad, select his number and press the left button with the phone icon.

6. The right button with the image of a handset ends the conversation.

To receive a call when Bluetooth is activated, the driver must press the button on the radio panel with the handset lifted. The connection may take about 5 seconds, but there will be no problems with subsequent communication.

In the improved Lada Priora, the standard radio transmits sound from the phone to standard speakers. Speakerphone allows the driver to be minimally distracted from the driving process, not break the law by talking on a mobile phone while on the road, and at the same time conveniently answer important calls. This system is attractive and is present in most modern foreign cars.

The high-quality equipment of the model allows you to get maximum comfort when buying a domestic car. But the standard Priora 2 radio is installed only on the “Lux” modification.

In other configurations, the owner will have to carry out modifications independently. And instead of a standard audio system, if desired, you can install a more expensive, but also more functional device.

Hello again and welcome to the logbook!

Due to numerous requests from Drayvovites, I hasten to tell you about the standard Priora tape recorder =). Yes, yes, you heard right =) such a thing exists =)

I’ll say right away that this 1Din device with a false panel has the following characteristics: reads CD/MP3, is equipped with USB, two-channel output, has built-in BlueTooth and is equipped with an LCD display =)

Next it’s worth talking about equalizer presets. We only have 4 of them =(.

The next stage of my story will be the quick settings block. You can dig into them by pressing the central toggle switch once.

Further. If we press the central toggle switch longer, we will find ourselves in a block of settings, which, as a rule, are set once. =)

Next I’ll tell you about BlueTooth. It’s a useful thing, I’ll tell you. =) only one thing is annoying, if you are not alone in the car and you receive an incoming call, the contents of which you would like to keep to yourself, then you have to reset it, because all passengers will be able to listen to the interlocutor, because it broadcasts through all the car speakers =)

By the way, you only need to connect your phone to the device once and then it will connect on its own, unless, of course, Bluetooth mode is activated on your phone. So, let’s call.

By the way, using Bluetooth, you can listen to music from your phone =)

That's probably all, although it would be necessary to show two tulips for the exit, located in the same glove compartment. =)

So, let's draw some conclusions. Among the advantages, it is worth noting the following: - fits quite well into the interior of the car. - no need to carry the socket with you. - good ergonomics, you don’t need to reach for it to control, the hand can easily find all the buttons. - LCD display displays information clearly, without distortion, everything is perfectly visible in any lighting. - price, with this audio system + 4 speakers and antenna the car becomes more expensive by 6,000 rubles. (declared by AvtoVAZ) Of the minuses: - frequent freezing when listening to a flash drive on which there is a lot of different information. - incomprehensible antenna: in the city the reception is worse than in the countryside. =) - very limited functionality, small number of settings. - after a conversation via Bluetooth, when listening to USB, for example, not often, but still, the radio starts playing. =(— for building a good car audio, IMHO, it’s still not suitable. Even though people wrote on the forums that they connect amplifiers and subwoofers.

Verdict. People who just listen to the radio or songs from the 70-80s in the car are definitely a must have =). Also suitable for the first time for those who, like me, are financially limited when buying a car, but want music to be everything it was =) And in the future he plans to install more respected audio devices. =)

Something like this. If you have any questions, don’t hesitate...

Options for installing a tablet in Priora

There are several options for installing a tablet in Priora 2:

an option when the mobile device is installed and powered from its own built-in battery;
when the built-in battery is removed and power is supplied from the vehicle's on-board network.

Which option to use - decide for yourself, it all depends on the level of preparation and the desire to delve into the essence of the issue in detail.

Types of radio mounts

To choose a method for removing a car player, you need to understand how it is fixed inside the panel. The following types of fastenings exist:

on 2 side clamps;
on 4 latches located on the side and top of the case;
fastened with self-tapping screws or screws to the brackets.

Example of mounting a standard head unit

Note. The last method of fixation is typical for standard devices that are supplied to the car by the manufacturer.

Latch on mounting frame

The principle of fastening with latches (clamps) is that the body of the radio is enclosed in a metal mounting frame, and is not directly built into the panel niche. This intermediate part, which has special petals with protrusions or grooves (depending on the brand and model of the device), is securely fixed in the niche. The player body is equipped with mating latches that engage when the player is inserted into the socket.

The counterpart of the latch on the body

To unlock the latches and remove the car radio, keys of various shapes are used, supplied by the manufacturer complete with music for the car. They are lost over the years of car operation, since they are used extremely rarely. As a rule, the key is a shaped strip of metal or a handle inserted into 2 pairs of holes located on the front panel of the device.

This is what most car radio removal keys look like

The mountings of standard radios are most often made with bolts, screwed to brackets and hidden under the front plastic panel. Here you cannot do without a minimum set of tools to dismantle this panel and unscrew the mounting screws or bolts.

Which tablet to put in Priora 2

Samsung Galaxy Tab 3 (with 7.0 screen);
more budget models from Lenovo (for example, the A3500 product).

Priora, Granta, Kalina

Let's start, perhaps, with the Russian automobile industry, which has such car models as Priora, Granta and the updated Kalina. All these models are equipped with standard car radios and navigation systems.

Kalina - in this car, the standard car radio can be installed in two types. The first is a 2 DIN car radio without a CD drive and without TouchScreen. The second car radio - without a CD drive, with a 7-inch display with TouchScreen, with support for MMC cards. The screen on Kalina is resistive and is more durable, and this also allows it to work in both extreme heat and cold. Not all playback formats are available on the MMC device. Basically, the car radio reads such popular music formats as mp3, wma and wav. In addition to music, it can also play video files.

The next time you turn on the GPS navigator, everything from the Windows folder will be deleted. To do this, find our installed driver and copy it to a folder called StsticStore.

We turn it on again and check it on the GPS, see if everything works, launch it by double pressing the Home button. Next, we return to the Windows menu on the desktop. At this point, the system will ask you for the driver again, but since we have already copied it in advance, in the window that appears we simply indicate its path StaticStoreUSBSER.dll. All these given options will help you and this problem will no longer bother you. The information that the Navitel version for Windows CE is not distributed is no secret to anyone. It turns out that you can’t buy it, which means you’ll have to download it from torrent trackers. For convenience, you can take versions 7.5 or 8.0. Navitel must find our GPS receiver, and for this we need to reflash it for further work with Com5 at an approximate speed of 4800. This comes with add-on patches with which you can do this.

We write Navitel to the MMC card in the root folder called NavitelContent, where the card itself will be located. Then we insert the card into the radio and launch Navitel. A sound signal will inform you that a connection with satellites has been established.

The standard car radio on the Grant and Priora has a similar navigation system, so the settings of the standard radio on the Grant, as well as the settings on the standard radio on the Priora, are the same.