How to disassemble the side view mirror on a viburnum

Tool:

Medium flat screwdriver
Medium Phillips screwdriver
Pliers

Parts and consumables:

Note:

The work is shown on the left outside mirror. Removing the right mirror is similar.

1. Use a flat-head screwdriver to pry off the exterior mirror trim.

2. We remove the lining.

3. Using pliers, remove the locking bracket of the ball joint housing of the handle rod.

4. Using a Phillips screwdriver, unscrew the three screws securing the mirror.

5. We remove the mirror along with the cables and the ball joint.

6. Install the outside mirror in the reverse order.

The article is missing:

Photo of the instrument
Photos of parts and consumables
High-quality photos of repairs

If suddenly, due to unsuccessful parking or, God forbid, your Kalina’s exterior mirrors were damaged during an accident, then the instructions below will be quite useful for replacing these parts yourself. I tried to describe everything in the most accessible language, and the process itself is very simple, so you should not have any difficulties when performing this work.

Replacing mirror elements

To replace the mirror elements of the Priora side mirrors, you will need a flat-head and Phillips screwdriver. Use a Phillips screwdriver to unscrew the side mirror from the door. Next, press on the bottom side of the Priora mirror element, a gap will appear. Insert a straight screwdriver into the resulting gap and unclip the lock of the mirror element. Then, disconnect the block with wires from the heater of the mirror element of the Lada Priora. Finally, you can unscrew the side mirror adjustment mechanism. Another replacement option is to simply break the mirror element with a hammer. Installation is carried out in reverse order.

Owners of a Priora in an old body can install turn signal indicators on the mirrors. Of course, you'll have to tinker with the wiring. On mirrors with turn signals, in addition to the adjustment and heating pads, a third pad is mounted. Turn signal block. On the Internet you can find a wiring diagram for the kit for installing a turn signal in the Lada Priora mirrors.

After all the manipulations with replacing mirror elements and installing repeaters. Mirrors should be adjusted to minimize blind spots. There is a universal way to adjust the mirrors, taking into account the body structure of the Priora. All you need to do is ensure that all mirrors do not reflect the same objects. If a car is visible in the left mirror, then it should not be visible in the interior mirror. Thus, the car behind will move from one mirror to another until it overtakes.

Mirror elements of the Lada Priora are a fragile part of the car, without which driving becomes dangerous. Mirrors must be kept clean and tidy. Moreover, you can replace the mirror elements yourself, with just a couple of screwdrivers on hand.

Detailed and universal method

Universal method

Inside the car, you need to unclip the plastic cover that covers the mirror mounting screws. After removing the cover, unscrew the three screws that hold the mirror in place and remove it. After this, you need to carefully remove the rubber gaskets -

If the rubber gaskets are damaged, it will be very difficult to buy new ones; they are rarely sold separately.

Now you need to unscrew the two screws securing the mirror adjustment joystick. Disassembling the joysticks themselves is a simple procedure; you just need to carefully remember the position of the cables and the color, since different colors are responsible for their adjustment. Next, you need to remove the three screws that are located on the lower plastic corner - it is most susceptible to damage during vehicle operation. After that you need to remove it too. How to remove the mirror element has already been described above. After removing the mirror element, you need to unscrew the four screws and remove everything else.

Place on silicone glue

The easiest way, of course, is to ask a mechanic you know or send the car to a car service center if you need to replace the mirror or paint it. But most owners are accustomed to repairing their car themselves - after all, this is a significant saving of money.

Basic knowledge

You won't be able to neglect the tuning process if you understand the purpose of proper tuning - reducing blind spots. A dead zone is a space on the side, behind or in front of the car, which, during a natural driving position, is hidden from the driver’s eyes and is not displayed in the rear-view mirrors. Controlling blind spots is especially important when changing lanes in heavy traffic. When another vehicle is in the blind spot, this means that it has not yet appeared in the field of peripheral vision, but is no longer visible in the reflectors.

Since reflective elements in a car are always installed at an angle, and are often convex in shape, the degree of reflected objects depends on the distance to the mirror element and the viewing angle. That is why the setup begins with setting the correct position of the driver's seat and taking your usual driving position.

Is the stereotype true?

You need to configure mirrors according to the principle - reflections should not duplicate the same information, but complement each other.

In the left corner it is clearly demonstrated that the incorrectly adjusted right mirror element shows the position of the car, which is clearly visible in the central reflector. The Community of Automotive Engineers came to this answer to the question: “how to adjust mirrors in a car” back in 1995 experimentally. It is worth recognizing that this method of adjustment goes against the usual recommendations of experienced drivers. The latter recommend adjusting the mirrors in the car so that the convexity of the rear of the car is displayed in the near corner. This position of the rear view mirrors has a right to life, but only in the case of drivers who do not feel the dimensions of their car. The unusual setting not only makes it difficult to reverse and park, but also prevents a novice driver from quickly developing a road situation in his head.

The photo clearly demonstrates the effectiveness of the mirror position, which is unusual for most drivers. With the traditional setup of fig.2, we see that the red car has left the driver's field of vision and is in the blind spot. An incorrectly adjusted reflector fig.5 displays a green car, which is unnecessary, since it is visible in the central mirror. When configured correctly, there is no blind spot on the left side of the driver, and a green car appears in the right side mirror as soon as it disappears from the central reflector.

To adjust, you need to place the car among static objects according to a pattern close to the images. To be able to double-check the correctness of the settings and remember the approximate position of the mirrors, so that later they can easily reproduce it.

Balance, useful tips

In some cars, getting rid of blind spots is extremely difficult or even impossible. Fortunately, there are not many such cars. It is worth recognizing that reflectors set in the described position can in some cases make driving difficult. Therefore you can:

if necessary, immediately before parallel parking or driving in reverse, install a rear-view mirror on the side (in the traditional way). A slight downward slope will help you see the curb better. Never make adjustments while moving! Therefore, immediately after parking, you need to re-adjust the mirrors, since then in a hurry you can simply forget about it;
When reversing, when you are sure that there are no obstacles on the right side, you can only navigate by the mirror closest to you. It’s more convenient to move this way, and in addition, later from the parking position you will have to reconfigure only one reflector;
install additional side reflectors that will be aimed at blind spots.

Now you know how to properly adjust your car mirrors.

Ignition coils

If everything possible has been checked, but the car won’t start, and you don’t want to take it to the service station until you’ve tried everything that you can try to fix it yourself, check the ignition module (coil).

First, let's check the wiring. We disconnect the block of wires from the coil, connect the middle wire to the plus of the multimeter (in voltmeter mode), and connect the minus of the multimeter to ground.

If, when you turn on the ignition, a voltage approximately equal to the battery voltage appears, then everything is in order with the power supply; we check the control circuits.

To do this, connect a multimeter to the middle and one of the outer wires of the harness and turn the crankshaft with the starter - a voltage of a couple of volts should appear, similarly with the other outer wire. If the wiring is normal, check the coil.

We switch the multimeter to ohmmeter mode, connect the tester to the middle and one of the outer terminals of the coil, if the circuit shows infinity, then that’s it - an open circuit. Same with the other extreme conclusion.

If everything is in order, we continue. We check the secondary winding - to do this, the coil must be removed from the engine and turned over. We connect the tester to the paired coil connectors - cylinders 1-4 or 2-3.

If it shows something other than infinity (should be something around 4 kOhm) then everything is fine, there is no break. Same thing with the other couple.

side mirror play

Hi all! The side mirrors on the 2001 Odyssey RA6 are loose. Who knows how to fix it, please tell me

damn it's the same bullshit, only on one side, I haven't figured it out yet

and how are they hanging out? Do the mirror elements themselves wobble (on bumps or from loud music), or the whole body?

If the elements are mirrored, then the latches may not be fully latched (damn... it’s a simple word, but it’s hard to write under beer). (mine was loose due to a bad latch)

Removing the mirror

The procedure after removing the upholstery is as follows:

Using pliers, carefully remove the locking bracket, which limits the mobility of the hinge.

Using a Phillips screwdriver, remove the screws that secure the mirror to the door structure.

The mirror is removed, all cables and hinge mechanisms are routed through a hole located in the outer door panel.

If we are talking about a mechanically controlled mirror, with automatic control, then it may additionally be necessary to remove the wires that provide the drive with electrical energy.

These wires are fixed in blocks, so disconnecting them is not difficult.

Installing a new mirror occurs in the reverse order of installing door trim.

The main thing is to control the correct connection of the wires in order to maintain the functionality of all electronic systems of the vehicle, direction indicators and heating

Cost of covers for Kalina mirrors

They cost on average from 500 to 1000 rubles, depending on the shape, color and method of attachment. Unpainted overlays can be purchased for only 200 rubles. Chinese cheap analogues cost very little (100-300 rubles), but are significantly inferior in quality. They are more fragile, brittle and inelastic.

Mirror covers for the Lada Kalina are the simplest but most noticeable tuning element!

The VAZ service station provides complete diagnostics and repairs of the Lada Kalina (1118) sedan.

Our car service specialists have extensive experience in maintaining and repairing VAZ vehicles, and thanks to our own auto parts store, we always have the necessary parts in stock.

View the price list for basic VAZ repair work

Prices for our car service services are significantly lower than the market average, which allows you to carry out high-quality repairs at an affordable price.

STO VAZ provides the following types of services:

Car repair Lada Kalina (1118) sedan;
Full diagnostics of VAZ 1118: diagnostics of the engine, brake system, suspension, compression measurement;
Maintenance of Lada Kalina 1118 sedan: changing engine and transmission oil, replacing filters, replacing technical fluids, replacing the brake system and timing belt;
Repair of the chassis: suspension, clutch, steering, brake system;
Tire fitting and storage;
Car wash;

VAZ-1118 is a new model of AVTOVAZ LLC, the production of which began in 2004. This is a five-seater passenger car with front-wheel drive, a front engine and an all-metal welded body. Lada Kalina is distinguished by a reinforced structure of the roof, sills and central pillar. Additionally, safety is ensured by bumpers made of impact-resistant polypropylene. The engine is four-cylinder, four-stroke, in-line, eight-valve, with a displacement of 1.6 liters.

In the basic configuration, Lada offers electric power steering, and as an additional set of options you can choose seat belt pretensioners, air conditioning, airbags, heated front seats, electric rear-view mirrors and an anti-lock brake system. All VAZ-1118 vehicles are equipped with special catalytic exhaust gas converters.

The exterior rear view mirror on the Lada Kalina is designed and dismantled very simply and conveniently, like everything on this model of a domestic car (in my opinion, the best in terms of price-quality ratio).

This particular mirror is suitable for both Tens and Priora. As we can see in the photo above, the mirror mounting principle is the same as on other Ladas, with one small difference. The side mirror is attached to three self-tapping screws using a shaped screwdriver (see photo above).

The side mirror itself (in this case, simple, without a turn signal repeater, with manual adjustment) consists of two parts. The main part (the mirror itself) and the protective cover. Connect these parts carefully and accurately by aligning the grooves on the mirror and the inserts on the lid and press it. It should click into place.

Next, lean the mirror on the outside of the door so that all three guides and the cable connection fall into place (photo above). Then, screw in and tighten the three screws. Make sure that the mirror on the outside of the door is level and properly positioned.

And now, that same “one small difference” - instead of the Zhiguli plastic nut that we screw onto the connection of the control cables, here it is attached to the same Zhiguli corkscrew, which on the classics secures the door lock cylinder. And finally, put on the plastic panel so that the adjustment lever fits into the rubber frame, lean the panel against the two guides in the corresponding holes and press it.

Mirror for Kalina, price 3000 rubles (with mechanical adjustment and without repeater)

Mirror for viburnum

The viburnum mirror often requires replacement. This is due to the difficulties of the first years of driving and the desire to install a more beautiful part. Replacing a side mirror is not a complicated process; the main thing is to be careful and follow a certain algorithm.

How to make a worthy choice?

Exterior mirrors are one of the most popular and essential parts of a car. Without them, it is impossible to monitor the situation and move along a busy highway. Side-view mirrors often require replacement, due to their high “trauma” during movement. Before work, you need to choose the best option for the mirror part. This could be a similar or more advanced mirror for Kalina. If difficulties arise when choosing, you need to familiarize yourself with the basic adjustment mechanisms.

The following types of mirrors are distinguished:

Ease of use depends on the choice of mechanism. The hinge type mirror element is the simplest. Many modern cars do not have it.

Lever control is based on a joystick or lever, which is located inside the cabin, and it is connected to the side part using a thin cable.

The electric mirror element is a modern mechanism. It is found in new cars and is equipped with a lot of additional features. Its use means comfort and safety.

Main advantages of the electric mechanism:

increased visibility;
anti-glare coating;
heating;
built-in turn signal backup.

Heated mirrors are modern developments that simplify the life of every motorist. Increased visibility allows you to better navigate city roads. This option reduces the likelihood of an accident by increasing the chances of noticing a dangerous moment. Finally, the clarity and appearance of this item is much better than the stock part.

The anti-reflective coating on the mirror on the viburnum allows you to reflect the sun and bright lights. The anti-dazzle effect maintains good visibility while driving.

Heated mirrors are a convenient option. Thanks to it, there is no need to scrape snow and ice from the glass. This is a very nice and convenient addition. Finally, a built-in signal repeater. This element of the Lada Kalina mirror allows you to notify all road users about upcoming maneuvers. This makes driving easier and safer.

When choosing the optimal mirror element for the Lada Kalina, you must take into account personal preferences. Naturally, we should not forget about convenience and safety.

Reasons for replacement and the process itself

Replacing a mirror on a Lada Kalina may be required in the following cases:

if the mirror element is damaged due to impact or temperature change;
if desired, improve the car;
in the absence of a “part” (as a result of theft).

How to change a mirror yourself, and what is needed for this? With a little skill you can get the job done easily.

The main thing to consider is that dismantling and installing it yourself requires caution. This will avoid breaking the new element and damaging the car body.

When removing an element, you must turn it out to the maximum. This process will be indicated by the gap formed between the part and its body. In this matter, the main thing is not to damage the element motors

The structure itself is carefully unscrewed using a Phillips screwdriver. It needs to be unscrewed from the car body and disconnected

This closes the question of how to disassemble a mirror. The next stage involves the installation of a new element.

The mirror element itself is located in the center, where it is safely secured with latches. The main thing is that it is secured correctly. To do this, you need to apply force and press on the part itself. Then the side element is screwed to the car body.

The process is not complicated, the main thing is not to damage the lining on the Kalina mirrors and not to spoil the mirror element itself.

Heating installation

If the car is not equipped with heated rear view mirrors, you should ensure that this option is available before installing the covers. During the cold season, this issue becomes most pressing. The large mirrors of the Lada Kalina will be of no use if they freeze completely and take a long time to warm up. Some car owners buy heated mirrors and install them on their vehicle. This installation is simple, but still requires some skill and experience. You need to know how to disassemble the door panel to route and connect all the wires.

There is a more complex, but much less expensive method. You can purchase flexible heating elements (GEN) and connect the heating to regular Lada Kalina mirrors.

Required materials and tools:

flexible heating elements that exactly fit mirrors in size;
Double-sided tape;
stationery knife;
file;
tools for removing rear view mirrors;
wires, heat shrink, electrical tape, etc.;
construction hair dryer;
screwdriver.

First you need to remove the mirrors of the Lada Kalina. Once this task is completed, the mirror element should be detached. The mirror can be attached using double-sided tape or special glue. You can easily remove a mirror glued with tape using the blade of a stationery knife. With glued elements the situation is a little more complicated. The glue softens when heated, which can be achieved using a hair dryer or hot water. It is important that the heating is gradual. A sharp temperature change can cause the mirror to crack.

Removing the door trim

To gain access to the elements that fix the mirror, you first need to remove the door trim.

The sequence of actions is as follows:

Removing the key blocking the lock.
Removing the plugs.

Sequentially unscrew the screws and screws holding the upholstery.
To remove the upholstery, you need to insert a flat-head screwdriver wrapped in electrical tape into the groove between the upholstery and the door panel (but it’s better to use a special device). The clamps provide some resistance, but significant force during dismantling is unacceptable.

The rods of the locking mechanism are removed, the upholstery is moved back to a distance limited by the length of the wires supplying the lifts.
The wiring is carefully removed, after which the door trim is also dismantled.

Search

Choosing a mirror in Kalina

Kalina mirror often requires replacement. This is justified by the difficulties of the first years of driving and the desire to install a more beautiful part.

Replacing a side mirror is not a complicated process; it is important to be careful and follow a certain method

How to make a worthy choice?

Exterior mirrors are one of the most important and important parts of a car. Without them, it is impossible to look at the situation and move along a busy highway. Side view mirrors often require replacement, which is explained by their greatest “trauma” while driving. Before starting work, you need to choose a balanced version of the mirror part. This could be a similar or more sophisticated mirror in Kalina. If you're having trouble choosing, you'll need to familiarize yourself with the basic setup mechanisms.

There are the following types of mirrors:

Ease of use depends on the choice of mechanism. The articulated mirror element is the most common type. Almost all modern cars do not do this.

The lever control is based on a joystick or lever located inside the cab and is pulled to the side by a narrow cable.

Electronic mirror element. this is a modern mechanism. It is found in new cars equipped with many additional features. Its implementation. comfort and safety.

Main advantages of the electronic mechanism:

increased appearance;
anti-glare coating;
heating;
Built-in double turn signal.

How to remove

and disassemble the side mirror

by car Lada
Kalina
.

replacing the mirror element with an exterior rear view mirror from Kalina, Grants and Priors

Video review of the self-service mirror element on the external rear view mirror of such cars

Heated mirrors. These are modern developments that simplify the life of every motorist. Increased visibility allows you to better navigate city roads. This option reduces the likelihood of accidents and increases the chances of noticing a dangerous moment. Lastly, the clarity and appearance of this item is much better than the standard part.

The anti-reflective coating on the viburnum mirror allows you to reflect both the sun and bright light. The anti-glare effect ensures good visibility while driving.

Heated mirrors. this is a convenient option. Thanks to this, you don't have to remove snow and ice from the glass. This is a very nice and convenient addition. Finally, there is a built-in signal repeater. This Lada Kalina Mirror element allows everyone to know the traffic about future maneuvers. Which simplifies the trip and makes it safe.

When choosing the best mirror element for Lada Kalina, personal preferences should be taken into account. Of course, do not forget about convenience and safety.

Reasons for replacement and the process itself

Replacing a mirror on a Lada Kalina may be required in the following cases:

in case of damage to the mirror element, due to a stroke or a decrease in temperature;
if you want to improve your car;
in the absence of “parts” (as a result of theft).

How to change a mirror yourself, and what is needed for this? If you have a little skill, you can get the job done easily. The main thing is that you need to consider, disassemble and install it yourself

this is caution. This will prevent damage to the new element and damage to the car body. When removing an object, you need to unscrew it as much as possible.

A gap between the part and its body will indicate this process. In this matter, the main thing is not to damage the motors of the elements. The design itself can be carefully unscrewed with a Phillips screwdriver. It must be unscrewed from the car body and disconnected. The question of how to disassemble a mirror is closed. The next step is to install a new element

When removing an item, you need to unscrew it as much as possible. A gap between the part and its body will indicate this process. In this matter, the main thing is not to damage the motors of the elements. The design itself can be carefully unscrewed with a Phillips screwdriver. It must be unscrewed from the car body and disconnected. The question of how to disassemble a mirror is closed. The next step is to install the new element.

The mirror element itself is located in the center, where it is securely secured with latches. The main thing is that he corrects himself correctly. Apply force and press on the part itself. The side member is then bolted to the car body.

The process is not complicated, the main thing is not to damage the gaskets on the viburnum samples and not to spoil the mirror element yourself.

Post Views: 2

How to remove a mirror from a windshield without breaking anything

09.10.2019

Issues discussed in the material:

How to remove a mirror from the windshield on a domestic car
How to do this on a foreign car
How to install a mirror after dismantling
What they say about removing the mirror from the windshield on car enthusiast forums

Every car enthusiast may have a situation when it is necessary to replace a broken windshield, or repair a rear view mirror, so information on how to remove a mirror from a windshield may be useful to anyone who owns a car.

Why remove the mirror from the windshield?

The side mirrors of a car may need to be removed in order, for example, to replace the glass on them, or in the event that the electric drive breaks down. It is worth noting that this must be done as carefully as possible, because this is a part of the body, damage to which will greatly deteriorate the appearance of the car. It is best to entrust this procedure to professionals, then you can be sure that everything will be fixed correctly and the paintwork will remain without damage. At the very least, the car service will take responsibility for the quality of repairs.

Even taking into account the fact that removing the side mirrors is quite easy, although the sequence of actions may vary on different brands of cars, independent dismantling can lead to damage to the electronics.

https://www.youtube.com/watch?v=tChRkpx-MLc

As for the rear view mirror in the cabin, here you can often come across a question from drivers: how can you remove it from the windshield without the help of a car service? Let's consider why such actions may be necessary:

You may need to replace broken glass or repair electronics;
if the mirror is not mounted tightly, sounds and vibrations may occur while driving;
if you want to tint the windshield (remember that according to GOST, tint cannot exceed 25%);
mirror upgrade, for example, with a rear view camera with parking sensors;
installation in the area of the rear view mirror of any devices and sensors not included in the vehicle configuration.

“Where to change a windshield: signs of quality service” Read more

For many car enthusiasts, the process of such dismantling causes difficulties, which is not surprising, because no one wants to break a mirror, damage the ceiling or break the windshield. At the same time, there are a number of practical recommendations that will help you carry out this procedure correctly.

How to remove a mirror from the windshield on a domestic car

Cars of the Russian automobile industry produced before 2009 were not distinguished by complex innovative solutions in the field of fastenings. Therefore, their owners are lucky here - unscrewing two bolts and removing the part will most likely not be difficult for anyone.

You can propose a simple algorithm for removing the interior mirror from the windshield in a domestic car:

you need to remove the plugs on the bolts (or skip this step if there are no plugs);
hold the mirror with one hand so that it does not fall out, with the other slowly unscrew the bolts;
Remove the mirror from the windshield and degrease the place where it is attached, for example, with alcohol.

Then, once the necessary repairs or upgrades have been made, everything needs to be secured in place. To do this, you just need to screw the bolts and put plastic plugs on them. It is important that the location of the patch on the windshield does not change after all the manipulations. As you can see, in the case of LADA cars, there are no problems with removing the mirror from the windshield yourself.

How to remove a mirror from the windshield in foreign cars

Is everything so simple with foreign cars? Let's try to figure it out. In fact, when removing a mirror from the windshield in foreign-made cars, a number of problems can actually arise, the biggest of which is the risk of damaging the windshield itself. The fact is that in foreign cars, in order to dismantle the mirror in the cabin, you need to put in a lot of effort, at the same time, the windshield is not designed for excessive pressure, and if you overdo it, it can simply crack.

“Types of windshields: what to look for when purchasing” Read more

We list the procedure for removing the rear view mirror from the windshield of a foreign car without the help of professionals:

since the fastenings here are equipped with plugs, they must first be removed, most often this is easy to do without the use of any tools;
further, the mirror needs to be pulled up, moving along the windshield towards the ceiling of the cabin, while it is important not to overdo it;
When dismantling, you need to be careful with the fastening so as not to break it.

If you need to remove the mirror from the windshield of a foreign car in order to tint the windshield, we advise you to abandon this idea or immediately splurge on a new windshield. The fact is that you won’t be able to tear the bracket away from the glass, and even if you manage to do this, a mark from the bracket will still remain.

If the dismantling procedure is carried out successfully, then the mirror should be in your hands, while the bracket itself should remain in place. It is necessary to control the efforts when removing the mirror, since you can sharply pull it up by inertia when it has already come out of the fastening runners, then damage to the ceiling with sharp edges is ensured.

Foreign-made cars also often have a special rear-view mirror lock in the interior. This is either a latch or a pedal that must be pressed so that the mirror can be easily removed from the bracket. Safety precautions for carrying out the procedure are also important here, since you can accidentally cut your fingers.

How to try to remove the mirror mount from the windshield yourself

Using brute male force to remove the rear view mirror mounts in the cabin, you can inadvertently break the windshield.

How to disassemble the side view mirror on a viburnum

Owners of a Lada Kalina car often think about possible improvements to their vehicle. Changes may concern the functional properties of the car or its appearance. Lada Kalina in the first body version has a discreet but stylish design. As for the restyled model, the exterior of the car has a little more aggression, which, by the way, suits it very well.

General characteristics of the car

Lada of the latest generation

You can change the appearance of your car in different ways. What tricks do Lada owners go to in order for their vehicle to stand out from the gray mass of cars. Tuning can change the appearance of a car beyond recognition. New bumpers, airbrushing throughout the body, eyelashes on the headlights, engine and interior tuning - this is just a small list of possible changes. More modest car owners try to only slightly emphasize the individuality of the Lada.

Kalina in the cheapest configuration differs only in mirrors and door handles, which are not painted in body color. In order not to overpay when purchasing another package, and not to lose the appearance of the car, you can buy covers for mirrors and handles. These elements are sold in pairs; if one is lost or broken, you will have to purchase a new pair.

As for the restyled version of the Lada Kalina, even in the basic configuration, which is called “standard”, all elements are painted in the body color. In this case, car owners change anything in the appearance of the car only based on their own desires.

For Kalina, both in the old and in the new body, new mirror caps will not hurt. These elements will help change not only the color of the mirrors, but also their shape and function. Nowadays, the market offers a large assortment of linings, allowing you to select parts in accordance with the taste preferences and financial capabilities of the buyer. These can be standard attachments for Kalina mirrors or painted in body color or equipped with additional options. Variations of forms are also very diverse. Stylish embossed mirror caps give the car sporty features. With them the car looks faster and more energetic.

Regular linings made of black plastic will cost 2-3 times less than those painted in body color. But in any case, it is an inexpensive and quite accessible pleasure.

What are mirror caps used for?

Installing overlays is advisable for several reasons.

The aerodynamic capabilities of the Lada Kalina are improving. At speeds above 80 km/h, the mirrors “whistle” noticeably less, since they have a more streamlined shape.
The car acquires an attractive appearance. Different overlays make it possible to experiment with the appearance of the car without damaging the paintwork and the car owner’s wallet. Kalina, unlike most domestic passenger cars, has large exterior mirrors. This not only provides a good overview. Such linings give the car a certain charm.
Lada mirror covers can be purchased complete with LED turn signal repeaters. This plays an important role in ensuring safe driving. When viewed from the front, the side turn indicators are poorly visible when driving, which can lead to an emergency. Installing overlays with signal repeaters will help avoid this problem.

Original mirror attachment

Having decided to purchase such parts for your car, it is important to know that the mirror caps that fit the Lada Kalina before 2013 will no longer fit on a car in a new body. In stores you can buy samples for each car variant, you just need to warn the seller about the make of the car and the year of its manufacture

You can purchase chrome, black, white and other trims. They can take the form of ordinary stripes, be placed on the corners of mirrors, or completely repeat their shape. Corners that cover only part of the mirrors look like part of the styling. Their choice depends on the character and taste preferences of the owner.

Methods for installing overlays

Even a beginner can handle installing the covers on mirrors created by VAZ. But if in doubt, it is better to send the car to a professional car service to avoid damage to the paintwork of the mirror with glue or solvents. The linings are equipped with all necessary fasteners or sealant.

Methods for installing overlays

Step-by-step installation of the lining using adhesive-sealant (usually silicone).

It is good to clean the outer surface of the mirror from dust and foreign particles and wipe dry.
Coat the inside of the lining with a small and even layer of sealant.
Carefully place the trim on the clean, prepared surface of the rear view mirror and press for a few seconds, applying slight force.
Remove excess silicone from the surface before the glue is completely dry.

Original mirror trim

If desired, you can always replace the adhesive sealant with double-sided tape. In this case, the tape is glued in several strips close to the outer edge of the nozzle or mirror, but not on the edge itself. Further, the technology is no different from that which involves the use of glue. If the pads come complete with fasteners rather than silicone, then their installation is even simpler. There are usually 3 to 5 latches. The antennae operate almost effortlessly, but they hold tightly.