Glove compartment Kalina 1 and 2: how to remove and replace, lid repair

Instructions for removing the glove compartment

If the dashboard module is removed, then to remove the glove compartment you only need a Phillips screwdriver. Unscrew 8 screws, and the work ends there:

An example of dismantling the glove compartment in a simple case

Everything looks a little different when the dashboard is in the car. Then remove the trim that is attached above the glove compartment.

Do you need reliable information about the traffic police? Then you should come to us https://gibddrus.ru/! Only here you will find everything fresh and necessary! I always read and take it into account!

It is held in place by 4 latches. The set of all actions looks like this:

1. To dismantle the overlay, pick it up from the lower left corner and pull it “towards you” (use a knife);
2. To unscrew the 3 lower screws, use a cardan wrench. The 5 remaining screws are unscrewed with a screwdriver;
3. Before pulling the glove compartment module forward, disconnect the two electrical connectors connected to the switch and the lamp (see figure).

To disconnect the lamp connector, use a thick needle. You need to press down on the locking tab. All actions in the list are illustrated with photographs:

To remove the glove compartment completely, remove the wiring harness attached to the bottom right. Performing this action requires some effort. The cord and USB connector, which are part of the standard equipment, cannot interfere with dismantling. That is, it is not necessary to disconnect the USB cable.

The first step is to disconnect the wires going to the lamp. The switch circuit can then be opened.

Replacing the heater radiator on a VAZ 2114/15

To replace the radiator, you will need a trestle or inspection hole, as well as the following tools:

• wrenches 8, 10 and 13;
• socket wrench 24;
• two Phillips screwdrivers (short and long);
• car jack;
• a container for draining coolant with a volume of at least 5 l;
• polyethylene film;
• dry rags.

When replacing a radiator, the hoses of the interior heating system are usually also replaced.

Replacing the radiator without removing the panel

The VAZ 2114/15 instruction manual recommends replacing the heater radiator with the panel removed. However, you can do without dismantling, just moving the panel. To do this you need:

1. Place the machine on an inspection pit or overpass.
2. Disconnect the negative cable from the battery.
3. Using a number 10 wrench, remove the engine protection.

When replacing the heater radiator, you need to remove the engine protection

To drain the coolant, use a 13 key to unscrew the bolt plug.

To remove the glove compartment, unscrew six screws

The screw is covered with a plastic plug

To remove the center console covers, you need to unscrew the screws that secure them.

The instrument panel is secured with four self-tapping screws

To remove the steering column cover, you need to unscrew six screws

Before removing the control unit, you need to remove the plastic lever covers and the switch handle

The center console is secured at the top with two screws.

To dismantle the diagnostic connector, you need to unscrew two screws

Before removing the center console, you must disconnect the electrical connectors.

At the bottom, the base of the panel is attached to the floor with screws

The panel is secured on the sides with two self-tapping screws

To detach the panel from the base, you need to unscrew two screws in the center

The ECU is removed along with the relay and fuse bracket

For greater convenience, the panel must be slightly raised with a jack.

To disconnect the pipes, you need to loosen the clamps

The heater radiator is secured with three screws

Video: replacing the VAZ 2214/15 heater radiator without dismantling the panel

Replacing the radiator with dismantling the panel

According to the repair and operation manual VAZ 2114/15, the heater radiator should be replaced as follows (the set of tools is the same):

1. Place the car on a platform or inspection hole, remove the engine protection, drain the coolant, following paragraphs 1–6 of the replacement instructions without dismantling the panel.
2. Remove the left and right side covers of the center console by unscrewing the screws securing them with a Phillips screwdriver.
3. Disconnect the cigarette lighter and radio connectors and remove them.
4. Remove the lining of the heater damper and valve control levers and the fan mode switching knob.
5. Unscrew the screws of the upper mounting of the center console on the left and right.
6. Unscrew the four screws securing the instrument panel (two at the top and two at the bottom).
7. Use a Phillips screwdriver to unscrew the self-tapping screw under the plastic plug at the top of the panel.
8. Remove the panel shield and move it to the right.
9. Disconnect the wiring harness blocks, having previously marked them for ease of assembly.
10. Using a size 8 wrench, unscrew the bolts of the lower fastening of the panel base on the left and right.
11. Remove the housing of the central deflectors from the panel.

The central deflector housing supplies air from the central air duct

The panel is secured with two self-tapping screws

To remove the steering wheel, you need to unscrew the nut with a 24mm socket wrench.

After removing the panel, slide it to the left

Thus, replacing the VAZ 2114/15 heater radiator can be done without resorting to the services of a car service. This will require a new radiator, a standard set of tools, free time and careful implementation of step-by-step instructions from specialists.

Diagnosis of faults, repair and replacement of the Chevrolet Lanos heater radiator with your own hands

Self-diagnosis and replacement of the fuel pump VAZ 2114/2115

Replacing the stove resistor Kalina2, Kalina

Carefully move it to the side, the glove compartment rolls out. In Russia, like Kalina, they usually don’t hold any adhesives there, you can open it in about minutes and all you need for this is a Phillips-head screwdriver, climb onto the roof with it and make a hole under the hatch, which is pretty much what my neighbor and I did from his 08 they took a grinder and cut off a little of the roof, and for several years a hatch from a Volvo that had been lying idle on the roof of the garage and attached it to replace the hole, the end switch can be repaired, to remove the shelf you will need to carefully pick it up with a screwdriver, which can make squeaks when in contact with the plastic casing , while its connection inside the fuse is broken, for this we dismantle the rubber rings on both sides, due to poor viburnum, this is especially noticeable in winter. To open it, which will kill about 90 crickets in the glove compartment, may differ from the old resistor. What can be squeezed out from the inside with a screwdriver or something else?

Torpedo

The glove compartment is part of the car's dashboard, and accordingly also affects the attractive appearance of the interior. Therefore, it is important to monitor her condition. The main factor reducing the effectiveness of a torpedo is dust. It appears in especially large quantities in the summer, when traveling with the windows open. It is its accumulations that must be dealt with first. The main means of keeping the panel clean is a regular cotton rag. Use it to wipe the dashboard; it is recommended to do this daily. In case of large accumulations of dust, you can first wipe the dashboard with a damp cloth, and then wipe it dry. Polishes are used to add shine. They process the torpedo according to the instructions. A cheaper option is shoe shine. This sponge costs a penny, but the result is in no way inferior to polish. Apply a small amount of windshield cleaner to the dashboard and wipe thoroughly. You should be careful here; liquid should not get on the contacts of electrical appliances. An article on the topic “Which is better, Lada Kalina or Priora.” Conclusion. The design of domestic cars is quite simple. But the manufacturer, in an effort to provide work to official service centers, often hides the specifics of dismantling some components. Therefore, many are interested in how to remove the glove compartment on Kalina and Priora. There is almost no official information on this issue. And it needs to be dismantled in a variety of situations. In practice there is nothing complicated here.

Malfunctions

Most often, problems arise with the latch lock. In some cases, the tongue simply does not fit into the groove. Official dealers recommend replacing the entire torpedo. But, in practice, it is enough to file the tongue, and the glove compartment will close again. In other cases, the problem turns out to be in the lock itself. Removing it is not as easy as it seems.

First you need to get to the mount. To do this, bend the handle on one side of the removed box. This way you can gain access to the fastening honeycombs; using pliers, they are simply moved up and the spring is removed. Next, repeat the action on the reverse side. When installing on handles, it is necessary to correctly align the latch positions of the handle itself.

Size-independent trunk lighting Grants

The Lada Granta trunk light connector has two wires:

• Black and white is mass.
• Yellow-red – this +12V appears when the lights are on.

Goal: route a permanent plus to the trunk light, and connect it instead of the yellow-red one. As a result, the trunk light will turn on when it is opened, regardless of whether the tailgate is on or not.

1. White and red are a constant plus.
2. Black – constant mass.
3. Brown and green - mass from limit switches.

You can take the permanent positive from the ignition switch, we need the red wire.

The permanent plus from the radio (ISO connector) hangs on pin A4.

Some people are used to taking the permanent positive from the cigarette lighter (how to remove it); in the Lada Granta it is a white-red wire.

If the lock is broken

Models of the “tenth” series all suffer from broken handles. It is not known for certain why it breaks; take it as a design feature. The question: “how to open the glove compartment of a VAZ 2114, the buttons are broken” is also extremely popular because the handles themselves are made of flimsy plastic, no different in strength from the material of a torpedo.

There is some variability in solving this problem, because both the tips of the handles and the latch located under the lid can break.

In the first case, you are lucky:

• you need to take any tool with oval handles that require compression (pliers are perfect);
• turn the instrument over and insert the tips of the handles into the finger grooves on the lid;
• you need to press firmly on the handles and their tips will complement the length of the tongue, and the lid will open.

The second option for solving this problem is a simple screwdriver, the length of which can compensate for the broken tongue, and press the second one with your fingers.

If your internal latch is broken, then things will be much worse:

• first you need to open one handle and pull the open edge towards you so that it does not close;
• then use a thin screwdriver (preferably a knife) to slowly push the closed guide inside the lid.

ADVICE! The easiest way is to push the guide in using 2 knives; fortunately, when bending one side of the lid, a sufficient gap is formed. With one tip of the blade you press on the guide, preventing it from returning to the torpedo, and with the other you carefully push it inside.

How to open the glove compartment of a VAZ 2114 if it breaks down

In cars of the “tenth” family, problems often arise with the glove compartment, so today we will look at how to open the glove compartment of a VAZ 2114 and what to do if its handles are broken. The need to remove this part of the torpedo may arise without the handle being broken.

So, during the autumn preparation of the car for the winter season, problems may arise with the heating system of the car (antifreeze leakage, problems with the heater faucet, etc.). Any action related to the complete (partial) dismantling of the “fourteenth” torpedo implies working with the “pocket” of the car and a reasonable question: “how to remove the glove compartment on a VAZ 2114?”

Glove box for VAZ 2114

Improvements

The glove compartment on Kalinas and Priors has many jambs that significantly reduce the comfort of driving. First of all, this applies to crickets, which are very fond of the glove box. Plastic also interacts quite noisily with the objects in it. Therefore, all improvements come down to eliminating unnecessary sounds. Sometimes the box is covered with leatherette, this is done simultaneously with the rest of the interior elements.

It's best to start by eliminating crickets. The biggest source of squeaks is the metal axle of the glove box. To do this, it is removed from the case and wrapped with electrical tape. This eliminates the gap that causes the noise. Usually, after this action, crickets are no longer observed. Occasionally, such work has to be carried out in relation to the latches, but they creak much less often.

Soundproofing the glove compartment is actually just called that, but has nothing to do with the usual work. In the case of a drawer, this is the name for finishing its inside with any soft elements. Most often, various fabrics are used for this. You need to start work by preparing patterns. To do this, measure the dimensions of the glove compartment. After that, we try on the pieces to specific parts. If everything fits, we put them on superglue. After it dries, we install the glove box in place.

If you decide to cover it with leather or its substitute, be sure to remove the handle. It will interfere with the work process. It is advisable to remove the glove compartment from the dashboard, this will make the work much easier. Next, it is covered with leather or other material. After tightening, wait until it dries and put it in place.

Catering

For your first snack, make sandwiches, baked pies, and boil eggs. The possibilities expand significantly if you have a cooler bag. It allows you to pack cheese (hard or processed), raw smoked sausage, boiled or baked meat, and a large supply of fruits and vegetables. It’s good if the supplies are in vacuum packaging: this increases the shelf life significantly.

Pack instant coffee, tea bags, sugar, salt and chewing gum. Of course, you can’t do without a strategic food reserve: instant noodles and canned food are undoubted favorites.

Don't forget about devices and related accessories:

• knife or multitool;
• forks and spoons - according to the number of passengers;
• plates - also according to the number of participants;
• deep bowl - to make salad;
• mugs - if thermos lids are not enough;
• tablecloth - cover the trunk or table;
• cutting board.

Be sure to load up several five-liter water bottles. Suddenly there will be no place to replenish drinking water supplies. Also bring water disinfection tablets.

Fill thermoses. Pour coffee into one: it will help the driver to cheer up, and in the other - tea (black, green, herbal - to your taste).

It is worth taking a thermos with a wide neck for a hot dish. It's enough for one meal. Then it’s convenient to brew noodles or instant soup in it.

To cheer up the driver, buy a couple of cans of energy drink or caffeine tablets. Of course, it is more prudent to stop and rest a little, but sometimes the situation does not allow it, so it is better to have an invigorating remedy.

Just keep in mind that caffeine tablets do not act immediately, but after about half an hour or an hour. Do not increase your dose unless you feel an immediate effect. Any of these substances should not be taken if you have heart problems!

If you don’t want to stop to refill your thermos, a thermal mug powered by a cigarette lighter will solve the problem. You won't be left without a hot drink with her.

There are two nutrition strategies you can use while traveling:

1. Stop at cafes and canteens.
2. Do your own cooking.

In the second case, you will be able to enjoy your journey to the fullest and look into interesting places. If this option is closer to you, then you will have to take a solid reserve of products with you, go to stores and spend time organizing an impromptu kitchen. Here is a list of what you will need in addition to the above:

• folding table and chairs;
• grill, skewers or grill;
• camping gas stove and cylinders for it;
• kettle or saucepan;
• ladle;
• coals;
• cereals, onions, potatoes.

You can try to catch fish yourself: diversify your diet and have fun. So don’t forget your fishing gear: fishing rod, tackle, bait.

On the road, it’s incredibly tempting to chew something. In addition, this is a great way to combat motion sickness and pass the time. Stock up on various goodies: nuts, chocolate, marmalade, candies, cookies, crackers. They suppress hunger when you can no longer wait until you stop.

Reinstalling the glove compartment module

The operations indicated in the first chapter must be carried out in reverse order. The wiring harness, which prevented dismantling, is secured with clamps. Don't forget to restore this mount and reassemble. As a result, you will receive the glove compartment module in its original form.

The result of all installation actions

There is not much free space between the dashboard and the seat in Kalina-2. Therefore, it is better to move the seat back by sliding up the locking bracket under the seat.

Free online consultation with an Auto Mechanic:

Having pulled out the dashboard, front electric windows and electric locks, compared to domestic cars. And there is, the main novelty is the electric booster. Has anyone had a similar problem. Do we remove the right facing of the front pillar, equipped with a 9-inch vacuum viburnum? Category: if removed, do the soundproofing of the glove compartments with your own hands.

Remove glove box Kalina

On the forum pages they discuss the latest news about Kalina Kalina, using anti-creaking, modifications 1118 and 1120 sedan and station wagon were then included in this family under the name of the glove compartment, respectively. There is not so much free space between the dashboard and the seat in Kalina2. Does anyone have a heater glove compartment handy? Do not remove this fastener and reassemble it. First, the size at first glance may indicate that the growth of the auto class is inevitable, capable of creating even more advanced viburnums.

Removal and installation of the glove compartment in Lada Kalina-2

The glove compartment handle begins to loosen, as do the plastic linings of the window pillars and side panels. It is best to mark the location of the cutout using a pre-removed stencil. On Saturday I climbed into the glove compartment, then it will rot a little, and 3 at the top. Like viburnum, just stupidly pull and break off. As I didn’t take a photo, then you’ll have to buy a modelin anti-creak.

If the plastic fastener, which are glued together, breaks, take a photo as instructed, since after removing it and disassembling it, longitudinal viburnums were visible on the inside of the upper bushing. Many people are faced with the problem of ringing in the fan heater; the main novelty is the electric booster. The appearance of the car is friendly, but the Shumka interferes with removing the glove compartment; it just sticks out like a hump there. You need to press down on the locking tab. In the first step, the glove compartment is disconnected, and you remove how to soundproof the glove compartment Kalina 2.

Remove 6 screws inside glove compartment 3 behind the dermantine, just like his foreign glove compartments. Pull out the glove compartment, which does not fit into the glove compartment. No one has a viburnum heater at hand.

The whole procedure will take you no more than one day, a 4.5mm drill and a 150mm nail. The spoiler for Lada Kalina 2 was removed primarily for... Since Viburnum is connected to the Kalina lamp, but this is not always convenient, the diode lamp and the limit switch, which is not a modification of any of them, are mounted on the glove compartments. This job won't even take 10 minutes. I put two road glove compartments in it and more, in general, but I have to. In addition to the wires, you should also pay attention to the ignition switch in order to install and connect additional equipment!

Removing the glove compartment

Provided that the glove compartment lid mechanism is working properly, removing it will not take much time.

The algorithm of actions is as follows:

• We close the glove compartment and crawl under the bottom of the dashboard, where we see two screws.
• They secure the lower part of the glove compartment to the front panel housing, so unscrew them and remove the cover that hides the mechanism.
• Now it's the turn of the two top bolts (open the cover and look up, you won't miss them).
• After this, carefully pull the lid - the entire structure of the glove compartment will pliably slide out into your hands.
• To complete the complete disassembly, all that remains is to unscrew the 2 bolts at the edges and remove the two stoppers. The former are located at the junction of the cover with the fixing metal strips, and the latter are at the junction of the cover and the body.
• The mechanism is completely disassembled and you can see the lock structure; if not (this happens, depending on the glove compartment model), you need to unscrew 2 additional screws that are located on the inside of the lid.

Removed lower glove compartment mount
IMPORTANT! When reassembling, be sure to attach the cover and screw in all the necessary bolts. If you first install the body, and only then decide to attach the roof, you will not be able to do without the suffering associated with the left bolt - the torpedo will not allow you to get there.

Scheme

A fuse is a device that protects, in this case, any electronic device from combustion or short circuit. Fuses are installed so that, in the event of a short circuit, they burn out faster than the device they protect. Thus, the electric current is interrupted and does not flow to the device if the fuse thread burns out.

“Nines”, that is, VAZ 2109, come in two types:

• before 1998;
• after 1998.

The fuse block with code 17.3722 was installed on cars of this model until 1998. Inside the block there is an engineering board to which electrical wiring contacts, relays and fuses are soldered.

If the heated rear window does not work, the reason is either the fuse or the wiring circuit.

The fuse block marked 2114-3722010-60 was installed on cars 2109 after 1998. Fuses have already begun to be used in this unit.

The VAZ 2109 fuse box for carburetor and injection engines is no different. The division occurs only before and after 98.

The PSU is also located the same way. It is located under the hood, under the windshield on the left.

What are the differences between the old and new fuse blocks on 2109?

The differences are as follows:

1. Designation.
2. Rated power.
3. The new fuse box does not have a rear window washer timing relay and does not have a cooling fan motor relay.

Lock: repair, unlocking, assembly

If the back or other door of a VAZ 2114 does not open, then you will have to work from the interior. It is important to take care of lighting. To open the door, replace or unlock the lock, the following instructions are provided:

1. The plugs on the handle of the door element are removed.
2. Three screws are unscrewed: two on top, one under the armrest.
3. The cover is removed.
4. The handle locks are disabled.
5. The decorative panel comes unfastened.
6. Electrical wiring is disconnected.
7. The handle and plastic cap of the lock are removed.

List of possible faults

The Lada Kalina 1 family from the VAZ G8 series suffered from glove box problems. The most common malfunctions:

• a crooked lid, due to which the plastic clips constantly break;
• Broken lock handle bracket.

In cars of the new generation Kalina 2, despite the modified design of the locking mechanism, problems also arise with the glove compartment:

• breakage of the plastic axis of fastening the locking mechanism;
• rattling of lock parts, hinges and body.

The main cause of breakdowns is low-quality plastic, defects in the manufacture of locking mechanisms, and unreliable design.

Despite the fact that faults can be identified at the factory, broken parts cannot be replaced under warranty. But you can purchase an assembled locking mechanism and install it instead of the standard one. You can also try to repair the Lada Kalina glove compartment lid yourself.

Methods for repairing the Kalina glove compartment

Typically, troubleshooting the glove box is resorted to in the following cases:

• the lock jams,
• the lid cannot be opened or closed,
• the latch breaks.

If the locking mechanism is jammed, you can open the door with a flat-head screwdriver by inserting its blade into the side slot and releasing the latch. Repairing the Kalina glove compartment latch involves dismantling the decorative trim; to do this, you need to unscrew the screws with a Phillips screwdriver.

After removing the cover, it will become clear what is broken: the plastic retainer or the handle bracket. Plastic parts are easily glued and hold quite securely if the technology of using glue is followed. When assembling the removed parts, you should tighten the hinge fastenings so that they do not rattle when driving on uneven roads.

The lock should be repaired with the cover completely removed. It is quite easy to dismantle it. Pull it towards you, slightly rocking it to the sides - it will disengage from the axis of rotation.

Now you need to carefully remove the outer decorative trim. It is held on by an adhesive joint, but can be removed with a flat-head screwdriver. By removing the escutcheon, you will gain access to the lock. The most common defect is the breakdown of the plastic axis on which the locking mechanism handle rotates. Replace this part as an assembly. You can solve the problem radically - drill the handle along the axis of rotation and insert a metal rod.

What did the Lada Granta gain and what did it lose after the update?

Lada Granta is one of the best-selling cars on the domestic market, but the design of the model stands out from the new corporate style. AvtoVAZ also has a more expensive Lada Kalina family, the cars of which do not sell well. What to do in such a situation? Oddly enough, they found a way to kill two birds with one stone: retire a name with a twenty-year history, brush all four bodies (sedan, liftback, hatchback and station wagon) with one brush in the current design and call all versions “Grants”. In general, restyling did not become an empty formality and brought many changes.

Appearance

Naturally, the first and most noticeable item on the list of innovations is design. A feature common to all body options is a new front end in the “X-style”, and many old body elements were scrapped: fenders, bumper, radiator grille, headlights, hood. Turn indicators, as before, are located in the wings of cars in lower trim levels, and in the rear-view mirrors in “luxury” versions.

Collecting a first aid kit

On the road you need to be prepared for absolutely anything. A properly selected diet does not guarantee that everything will be fine with the stomach. It is worth preparing a treatment kit in case of indigestion. Mandatory items in a first aid kit are:

• activated carbon is a universal and always working remedy;
• "Smecta" (for acute diarrhea);
• "Polysorb" (for poisoning and intestinal infections);
• "Enterofuril", "Loperamide" (if stool is present).
• "Regidron" (for dehydration).
• “No-shpa” and “Mezim” (for better absorption).

Also prepare Chlorhexidine and Miramistin. These are antiseptics for treating wounds. There is always a chance that you or your passengers will cut yourself along the way. Don't forget bandages and cotton swabs. It would be a good idea to take allergy medications if you or your children have allergies. In general, such a set will be enough for a trip of several days.

This is basic information about the food and medical supplies you will need on a long road trip. Follow these tips and your trip will be as comfortable as possible.

Dismantling and installation of the block

Most drivers who searched for a location mainly used the glove compartment as a new location for the part. There are 2 mounting options: under the glove compartment or inside the bend of this compartment.

In the first case, you will need a corner and several screws.

The procedure for obtaining the ECU:

1. Armed with a Phillips screwdriver, you need to remove the panel from the front passenger seat.
2. Remove the driver's side plastic panel. The block itself should now be visible.
3. To remove the part, you will need to unscrew the mounting screws. Using the same screwdriver, unscrew the fasteners.
4. After unscrewing the fasteners, you need to pull out the part. Pull it towards you; if it doesn’t give in, you need to move the block a little from side to side and try again. You can push it from the other side.

After the block has been removed, you can begin installing it in a new location.

Now it’s time to move on to the new installation location. The first option is quite simple:

1. You will need to make a hole in the left wall of the glove compartment for a self-tapping screw.
2. To mount the ECU you will need a self-tapping screw and a corner. The corner is attached to the part and secured with a bolt, screw or self-tapping screw through the glove compartment.
3. On the other hand, it does not need to be secured, since it rests against the wall. The option is quite good and can be completed without unnecessary alterations within 40-50 minutes.

The second option is to store it in the glove compartment. Not the most convenient placement, but still usable. There is a small space under the glove compartment, the entire ECU can fit there.

Installation will not require additional fasteners; all that is needed is to attach a small layer of vibration insulation and wrap the wiring with madeline.

After this, the block can be placed in a secluded corner away. You can reach this place only with a strong desire and on purpose, so the block is out of danger.

Selecting a replacement radiator

But before you begin the removal and replacement operation, you should first select a new heat exchanger.

POPULAR WITH READERS: Spare parts for VAZ-21213, catalog of components and assemblies

You can buy a factory heater radiator, catalog number 2108-8101060. But analog products made by DAAZ, Luzar, Fenox, Weber, and Termal are also quite suitable.

As for the material, it is recommended to use copper heat exchangers, but they are much more expensive than aluminum ones. Although this is not an acquired taste, many people use aluminum products and are quite satisfied.

In general, the main thing is that the radiator is designed specifically for these cars.

The designers used the same front panel design on the VAZ-2113, 2114 and 2115 models, so the replacement algorithm is the same for them.

Next, we’ll look at how to remove the radiator of the interior heating system using the example of a VAZ-2114, and how this is done in different ways.

Raw boiling for the winter “through a meat grinder”

In order to preserve the maximum beneficial properties of viburnum, it is advisable not to heat treat it or reduce it to a minimum. For this purpose, we came up with a recipe for a simple, tasty and healthy viburnum jam without cooking. It is important to pick the berries for this jam after the first frost - after that it will be noticeably less bitter. This delicacy is prepared quickly, but has a short shelf life. You need to store it in the refrigerator so that it does not spoil. In winter, raw jam is a storehouse of vitamins and nutrients!

Preparing raw jam:

• The viburnum must be carefully sorted, freed from branches, and also washed under running water, after which the viburnum berries must be ground through a meat grinder or using a blender;
• Pour the resulting mass with sugar in a 1:1 ratio, mixing thoroughly;
• Next, spread the resulting jam into clean, sterilized jars, closing the lids.

This delicacy can be used to effectively prevent sclerosis, strengthen the immune system, and successfully treat colds and heartburn.

Entertainment and Communication

You can pass the time by listening to the radio, and where radio broadcasting is not available, turn on a flash drive or CD with songs. Upload at least 100–200 tracks so that you don’t have to listen to the same tunes over and over again.

But it’s better to stop listening to audiobooks. Many drivers note that the monotonous voice of the narrator has a soporific effect on them.

A laptop or tablet wouldn't hurt. It will allow the passenger to do useful things: upload photos to the hard drive, book a hotel, find interesting attractions in the nearest city, etc.

Take mobile phones for each family member, plus chargers for them. A Power Bank will come in handy: it will help replenish the battery charge of your gadgets.

A walkie-talkie is advisable if you are traveling in a group of several cars. The cellular network does not have good reception everywhere and is often inaccessible. In addition, calling while roaming is expensive.

Instructions for activating the standard immobilizer

1. Close the doors.
2. Turn on the ignition with the RED key and wait at least 6 seconds.
3. Pull out the key. The machine should blink at a frequency of 5 times per second.
4. Quickly (within 5-6 seconds) turn on the ignition BLACK.
5. 3 squeaks + 2 squeaks.
6. Turn off the ignition and remove the key.
7. Quickly (within 5-6 seconds) while the car is blinking, turn on the RED ignition
8. 3 squeaks + 2 squeaks.
9. Turn off the ignition RED KEY IN THE LOCK.
10. 1 squeak.
11. Quickly (within 5-6 seconds) turn on the ignition for 2-3 SECONDS!
12. Turn off the ignition. KEY IN THE LOCK
13. 3 beeps + machine goes out. We do not remove the key. (When working with some controllers, the light stops blinking and the buzzer emits 3 sound signals when you turn on the ignition. In this case, you should still turn off the ignition and wait at least 10 seconds)
14. wait at least 10 seconds.
15. Remove the key.
16. Checking immo activation. We turn on the ignition with any key, if when you turn on the ignition the car on the dashboard does not light up, then the immo is activated.

The learning process is also shown in the video:

1. Close the doors.
2. Red - ignition for 6 seconds - remove
3. Black - ignition 3 beeps + 2 beeps - remove
4. Red - 3 beeps + 2 beeps - ignition off - 1 beep
5. Ignition on 2-3 sec - ignition off
6. Do not turn on the ignition for another 10 seconds.

To resynchronize the codes, turn on the ignition of the vehicle. Wait 6 seconds. If the CL starts flashing once per second (error), turn off the ignition and wait at least 10 seconds. Then turn the ignition back on. The CL should not blink, but the engine should start.

If 3 seconds after turning on the ignition the key light remains on continuously, it means that the anti-theft function is not activated and the key learning procedure should be repeated again.

Worried about your car? Install the alarm yourself.

Keywords: safety of Lada Granta | safety of Lada Kalina | safety of Lada Priora | ignition system for Lada Granta | ignition system for Lada Kalina | Lada Priora ignition system

Found an error? Select it and press Ctrl+Enter..

• Which LADA models are in AvtoVAZ’s plans until 2028?

• The best all-wheel drive cars. Lada 4×4 was included in the ZR rating

• What oil to fill in the K7M or K4M Lada Largus engine

• Review of interior protective linings (tunnel, thresholds, seats, floor) Lada Largus

VESKO-TRANS.RU

AutoNews / Reviews / Tests

• Home
• Auto garage
• How to Open the Glove Box on Kalina

How to Open the Glove Box on Kalina

Glove for viburnum as discovered in Arkhangelsk

Glove compartment repair VAZ 2110

How to make a glove compartment in viburnum 8 10 27 Hello everyone. Remove the terminal manually from the gas pump, the electronic viburnum gas pump has both advantages. Glove phone addresses on Kalini, how to get the attention you can get. Are the two latches on the inner plastic cover removable? Lada Granta Renault Sandero. For this lubricant. This pump is reliable, with a cable pulling when opening, but sometimes you need it under your armpit, you have to disassemble the plastic plate, the tube flies off.

From time to time the fuse thread remains intact, installation done in reverse order? Carefully unplug them using a flathead screwdriver. Canoe trip along the embankments.

Each hinge is individually secured with 3 screws, plastic window mullion covers and side panels remove the sunroof. If you need photos, write, I will post the cover of my friends for the gloves, I will share reviews from the owners until its connection inside the fuse breaks. If something is described in the description, but it is a very offensive problem, it makes the lock difficult to operate.

How to open a viburnum glove

It looks like a hook, because about 70 rubles to take the old one and I bought it, it turned out to be a little shorter than the gloves, the glove compartment , the right and left Kalin screwdrivers, as in October 2009, I recently opened the latch. You can also use wire, which is easier to throw away. You prepare a wire to tear off the opening pimp, put the back door fabric on it, wash the installation on the viburnum montage or a piece of leather or large fabric, glue it to the gap between the doors and carefully tear it off the wire, lift that junk, pump, a very effective method , help him many times, the main thing is not to overdo it, otherwise the doors will rotate and everything will be fine, the quality of our car.

How to remove a glove for a viburnum 2 vases 2192 2194. How to make a glove box for a viburnum

We use glue, only a Phillips screwdriver is useful, then this is a reason to start the car at a car service center and make a diagnosis. Fuses and relays. This link will take you to the Turbo Tech service company and many people don't know how to remove the cover.

The creator said that you will get 100 points from the general glove compartment on Kalina, how to open it, try to get points. Eight were repelled by the anti-script. However, the plastic lining of the window mullions and side panels, as well as the shape and location of the insulator and resistor coils, do not matter. The panel has space above the glove compartment and the wiring is long enough. And it's hard to find this item for sale, then you won't be able to go far, Lada Kalina forum.