Replacing light bulbs in the rear lights of a Priora station wagon

Removing and installing a rear light on a Priora

So, first of all, we open the trunk lid, and on the inside we find a special technological window with Velcro that needs to be opened. It is through this that you can get to the flashlight mounts.

It is worth noting that from the inside it is not mounted with bolts, but with special plastic screws that secure the lamp to the car body. There are three of them in total, of course, each of them must be unscrewed. After this, we move the lantern to the side from the outside, as is clearly shown in the photo below.

If it is necessary to replace the rear light, then each of the lamps should be pulled out of the light housing from its rear part. More on this below.

Replacing the brake light bulb of a Priora hatchback

1200 rub. for the photo report

We pay for photo reports on car repairs. Earnings from 10,000 rubles/month.

Write:

The light bulbs for the dimensions, brake light, reverse and turn signals in the Priora's taillight essentially change in the same way as on the Kalina, that is, to replace the bulbs you will first need to remove the taillight. To unscrew the headlights, you will need to partially bend the carpet (trunk lining) in order to get to the fastening bolts. It is not necessary to disconnect the light bulb connector because the length of the wires will be enough to set the flashlight a little to the side and unscrew the socket of the required light bulb. All bulbs in the taillight are replaced in the same way. To illustrate the process of removing the rear light of a Lada Priora hatchback and changing the brake, parking, reverse or turn signal lamps, watch the video.

We will show you how to replace the brake light, clearance and turn signal lamps in the rear lights of a Lada Priora Hatchback with your own hands. In essence, the light bulbs are changed in the same way as on the Lada Kalina; you first need to remove the entire headlamp and only then can you get to the light bulbs. With the trunk open, we need to unscrew at least one screw securing the trim and then disconnect the trim from the latch, pull out the latch and move the trim to the side to make it more convenient to continue working:

Or do this work through special technological holes in the carpet (with Velcro):

We choose the first method, it is much more convenient and everything is clearly visible. First, we’ll tell you how to remove the rear lights, two plastic screws are located in the photo at finger level, one is a little further away, you need to unscrew them immediately:

All this can be unscrewed by hand. When you unscrew the third one, it is advisable to hold the lantern so that it does not fall. After this, you can move the flashlight away and remove the light bulb we need. To do this, take it by the base and turn it counterclockwise. Insert the new light bulb all the way and turn it a little.

Video of replacing the brake signal lamp, dimensions, turn signal in the rear lights of the Lada Priora Hatchback:

Backup video instructions for replacing rear light bulbs in Lada Priora:

Replacing the brake light bulb, tail lights and turn signals on Priora Hatchback and Sedan

Video review of replacing light bulbs in the rear lights on a Lada Priora hatchback

Replacing the brake light, tail light, turn signal lamp on a Priora

Now, in the same way, we take the lamp itself, and turning it counterclockwise relative to the socket, we remove it.

Replacing the lamp is carried out in the reverse order. It is worth keeping in mind that when installing new bulbs in the Priora's taillight, you must adhere to the same rules as with the front headlights. That is, you should not touch the glass of the lamp with bare or dirty hands, otherwise this will lead to a decrease in its service life.

Headlight bulbs

On the Priora, the configuration of the front lights differs, depending on the year of manufacture. Since 2013, a new version has been released in which they were replaced.

Headlight bulbs for Priora models up to 2013.

Headlight lamp for Priora after 2013

The only difference is the high beam lamps. Instead of the H1, the H15 model with additional daytime running gear was used.

To replace the front light bulbs in a Priora, use these instructions:

1. To dismantle the low and high beams, you need to remove the plastic cover from the headlight protection. Then gently pull it towards you and remove it. Press the fastener of the light bulb and pull it out.
2. To pull out the rotary ones, just unscrew them counterclockwise.
3. To dismantle the dimensions in the Priora, pull the fastener towards you.

Installing LED tail lights on Priora

As for LED tail lights for Lada Priora cars, their prices are of course a little higher. Namely, a set of such lighting equipment can be purchased for around 3,200 rubles. As for installing a flashlight instead of a standard one, there is absolutely nothing unusual here.

It is necessary to disconnect the power connector for the flashlight, which is standard for all types of Priora, and then, after removing the old flashlight, install a new one with LED lights in its place. There is no need to perform any additional actions or manipulations. And the result of the work done can be seen in the photo below:

If you have any questions about the material provided, or have something substantive to add, please write below in the comments.

In each car, the headlight bulbs are changed differently, so it is almost impossible to create the same type of instructions. This article will discuss replacing taillight lamps in a Priora.

AvtoVAZ designers did not provide for the possibility of changing lamps without dismantling the lamp itself and it must be removed before replacement. Therefore, it would be more correct to first talk about its removal, and then about removing the lamps.

Features of headlight adjustment

About the design and operation of the car What is better than Lada Priora or 2112. What is better than VAZ2112 or Priora. Calculations and miscalculations

It is advisable to place an assistant in the driver's seat or place a load weighing about 75 kg. The vehicle's tires should be well inflated and the tank at least half full to bring its weight closer to the weight at which it is driven daily.

The adjustment is carried out on a vertical wall or stand on which markings are applied. To correctly adjust the optics, it should be possible to move away from the wall at a distance of 5-10 meters. This makes it possible to create an imitation of lighting on the road.

Wall marking scheme

To apply markings, you need to place the car closer to the wall and turn on the low beam. Then you need to alternately mark the center of the trace from each headlight and the centers of their symmetry. By connecting these points, we get a horizontal line. Then, below, two more lines should be drawn in parallel. The second is at a distance of 5-12 cm, and the third is at a distance of 22 cm from the first. In addition, you need to draw vertical lines through the center points of the car and the lights.

After turning on the light, you need to ensure that the top point of the light is on the second line. The adjustment is made using an electric headlight adjuster. The adjusted light will illuminate the road well and will not blind oncoming drivers.

Removing and installing the flashlight

The rear light is accessible from the luggage compartment of the Priora. To directly get to the lamp, you need to pull back the trunk trim.

The process of removing the rear light

• We open the trunk and fold back the upholstery in the rear part of the wing.

• Then you can see 3 wing nuts that hold the flashlight on. We unscrew them while holding it on the other side.

• Next, pull the flashlight towards you and remove it from the rear fender.

• Removing the lamp socket is done by turning it counterclockwise and pulling it towards you.

• Installation is carried out in reverse order.

Replacing lamps

After the lamp is removed, you can begin replacing the lamps.

• To do this, unscrew the lamp socket by turning it counterclockwise.

• We take out the cartridge. The lamp should be removed from the socket by slightly pressing it and turning it counterclockwise 90 degrees. After this, the lamp should come out of its seat.

• Install new lamps in reverse order.

In what cases is it necessary to replace and adjust headlights?

The main reason why optics are replaced is their failure and the inability to perform their functions: high-quality road lighting. In addition, the lamps in the lanterns are changed. Bosch lamps are in demand. Bosch brand xenon produces better quality light and has a longer service life.

Bosch xenon lamps

Optics should be changed for the following reasons:

• the headlight sweats, its ventilation is impaired;
• cracks, chips on glass;
• reflector malfunction;
• faults in electrical connectors;
• defects in fasteners;
• tuning

During the replacement process, you can not only restore the functionality of the flashlight, but also improve its performance characteristics by replacing halogens with xenon. Using xenon in lamps, the driver receives better lighting. At the same time, tuning of the headlights is also carried out: lens glass is installed, black headlights look impressive. LED lamps are installed in the parking lamps, as well as in fog lamps.

Front lights with lenses

To make your car tuned, you need to know how to remove the front and rear optics.

What kind of lamps are installed in the Priora headlamp?

The Priora's rear light has 4 lamps, which are responsible for turning on the turn signal, dimensions, reverse, brake light and PTF. They are almost the same, but have some differences.

• The turn signal lamp is marked PY21W and is orange; when installing a regular white lamp, the turn signal will blink white.
• The size and brake lamp has two spirals, which are responsible separately for braking and illumination.
• The reverse lamps and PTF lamps are the same.

Tail light lamp marking table

Replacing brake light bulbs and parking lights

With the release of the restyling of Priora 2, a large number of details have changed in it. The rear lights are especially noticeable; they have become LED. Now the dimensions have become lower, which gives the car a wider appearance in the dark. To achieve this effect, it is not at all necessary to buy and install LED lights.

To do this, just swap the backlight from the top position to the bottom. We don’t touch reverse and turns!

After such a replacement, when you press the brake pedal, the brakes will light up where the side lights and fog lights were previously illuminated. And the dimensions and rear PTFs will glow from the bottom of the lamp.

How to check the operation of brake lights

Checking the functionality of the brake lights does not take much time. This requires two people. One should press the brake light, the other should make sure that all three brake light bulbs come on.

It is also possible to check the functionality of the “stops” alone. For example, you can press a brick onto the pedal or insert a stick between the seat and the pedal. But it’s easier or easier to invite an assistant, with the words: “Hey, you, come here”)

Troubleshooting

• If all the brake lights do not light up, the first thing to check is the power fuse. It is located in the main mounting block under the dashboard, at the driver’s feet. The fuse number is F10. In addition to the brake lights, it protects the power supply circuit for the interior lighting and instrument panel lights. The fuse condition can be determined visually. If the conductor is burnt out, the fuse must be replaced. If it burns out again, the short circuit must be found and repaired.
• Next you should check the lamps. To do this, you need to remove the non-working lamp from the headlamp and replace it with a known working one. Alternatively, you can check the resistance of the llama, but this option is much less reliable.

Advice: it is quite possible for two brake light lamps to burn out at the same time, so if the Priora brake lights, in addition to the additional one, do not light up, first you need to check the lamps, then the wiring.

• Another reason is oxidized contacts in the headlight unit. Oxides can be detected visually by simply removing the lamp from the socket. To clean the contacts, you should use sandpaper; if you don’t have it, you can try to scrape off the oxides with a screwdriver or knife, or simply twist the lamp in the socket to remove the oxidized layer.
• The contacts in the wire blocks that fit the headlight may also oxidize. You should inspect the contacts and, if necessary, clean them with a thin screwdriver. It is necessary to clean the contacts on the board and on the block. In the field, you can try to put on and remove the connector from the headlamp several times to clean out the oxides.
• Next, you need to check the condition of the tracks of the headlight unit on which the brake light does not light up. It’s better to do this with a multimeter, but damage is often visible “by eye.”
• If the track is burnt, it can be restored by soldering a thin copper wire.
• If all the lights do not light up when you press the brake pedal, you should check the sensor (switch) located near the brake pedal. This is easy to do: you need to remove the wires from it and short-circuit them. If the brake lights come on, the sensor must be replaced with a new one. Otherwise, you need to check the electrical circuits.

Video on replacing lamps

Alexei:

Which lamp should I put in the brake light of Lada Priora 21/4 or 21/5?

Teddy Bear E:

Sandro, thanks for the video! Helped!

Mag Aliev:

helped a lot

Meirkhan Michon:

thanks to the author

stason73rus:

but my stop lights are not on in Priority and the rear window is on Brake light, fuse is ok. What could be the reason? blogging in advance.

Marina Korshikova:

Sandro, good, I watch your videos regularly, they help a lot. I’m just sorry for your viburnum, how many experiments you have put into it.

Andrey M:

Thank you, this video was very helpful today!

radio controlled models:

sell me the speakers

Dennis Dennis:

Remove the Faro to change the bulb!

Gray matter:

bulbs, how can you not touch them with your hands? or am I confused

Makarov Alexander:

Kalina1 sedan too

Video on this topic

how to remove rear lights on Lada Priora

Lada Priora station wagon: replacing the foot in the headlights

I'll show you how to change light bulbs in the headlights of a Priora station wagon.

Removing the Priora station wagon lamp

Removing the tail of a Priora station wagon VAZ 2171.

how to remove epiphany on Lada Prior, Everything is done quite simply. Fold the gasket on the removable side.

Previous LED, reverse lamp replacement

P21W Reversible LED lamp.

Lada Priora station wagon: replacing paws in headlights

I'll show you how to change the headlights of a Priora van.

Installing LED rear lights on Priora

Online store EXELET.RU Tolyatti, st. Officers 12B, office 206 Tel https://exelet.ru PRIORA on Drive2.

Spare flashlight for Priore

Spare flashlight for Priora.

How to replace the brake light in the rear of a Priora hatchback |

Our group is in contact. JUST THINK https://vk.com/ProstoeMnenie Become a YouTube partner https://youpartnerwsp.com/join?9658 In the video.

Replacing rear light bulbs on a Priora | How to change turning lights and brake lights on a Priora

Replacing light bulbs for turns, markers, brake lights, and rear lights on a Priora. Take the Priory Lada with a burn.

Replacing rear lights with Priora

Learn how to change the brake light, rear dimensions and rear angles of a hatchback.

Replacing a lamp with a stopper, rear size and inclusion of an accelerated hatchback and sedan

Video review on how to replace rear lights on a Lada Priora hatchback.

Video on this topic

how to remove the rear light on a Lada Priora

Lada Priora station wagon: replacing the tabs in the headlights

I'll show you how to change the light bulbs in the headlights of a Priora station wagon

.

Removing the Priora station wagon lamp

Removing the rear light of a Priora station wagon

VAZ 2171.

how to remove the rear light on a Lada Priora , Everything is done quite simply. We bend the upholstery on the side to be removed.

LED in Priora, replacing stock lamps in reversing headlight

LED reverse lamps P21W on led.

Lada Priora station wagon : replacing the tabs in the headlights

I'll show you how to change the light bulbs in the headlights of a Priora station wagon.

Installing LED rear lights on Priora

Online store EXELET.RU Tolyatti, st. Ofitserskaya 12V, office 206 Tel https://exelet.ru PRIORA on Drive2.

Replacing a flashlight on a Priora

Replacing the headlamp on a Priora.

How to change the brake light bulb in the rear lights of a Priora hatchback

Our group in contact SIMPLE OPINION https://vk.com/ProstoeMnenie Become a YouTube Partner https://youpartnerwsp.com/join?9658 In the video.

Replacing rear light bulbs on a Priora | How to change turn signal and brake light bulbs on a Priora

Replacement of turn signal lamps, side lights, brake lights, rear lights on a Priora. We take the Lada Priora from the burnt one.

Replacing rear light bulbs on a Priora

Details on how to change the brake light, tail light and turn signal lamps in the tail light of a Priora hatchback.

Replacing the brake light bulb, tail lights and turn signals on Priora Hatchback and Sedan

Video review of replacing light bulbs in the rear lights on a Lada Priora hatchback.

The design and arrangement of the rear lights on a Lada Priora car are such that if it is necessary to replace one of the failed bulbs, you have to remove the light completely. It is logical to first consider the procedure for removing the rear light using the example of a Priora in a hatchback or sedan.

Lamps in the rear combination lamp

Note: The following describes how to replace the bulbs in the rear combination lamp on the left side. Replacement on the right side is carried out in the same way.

1. Disconnect the wire from the negative terminal of the battery.

2. Open the tailgate.

3. Inside the luggage compartment, bend the two flaps of the upholstery, covering the three wing nuts of the studs that secure the combination light.

Note: Shown below with luggage compartment trim partially removed for clarity.

4. Unscrew the two wing nuts of the combination light mounting studs, shown below.

5. Holding the taillight with one hand, unscrew the remaining third wing nut with the other.

6. Remove and move the rear combination lamp slightly to the side to gain access to its lamps.

7. Now you can replace the burnt out lamp(s). As an example, let's replace the side light and brake signal lamp (all lamps in the rear combination lamp are changed in the same way).

8. Take the lamp socket and turn it counterclockwise.

9. Remove the socket with the lamp assembly from the flashlight body.

10. Pressing the lamp, turn it all the way counterclockwise and...

... remove the lamp from the socket. Dispose of the burnt-out lamp as waste.

11. Take a new lamp with similar characteristics (markings) and install it in the socket all the way in the reverse order.

Note: When installing the lamp, two protrusions located asymmetrically relative to the axis of the lamp must fit into the corresponding grooves of the socket.

12. After replacing the lamp(s), install the rear combination lamp on the car in the reverse order.

How to disassemble a fog light

Everything is quite simple here. It is necessary to remove the lamp from the car. Then remove the sealant using a powerful hair dryer and a mounting knife. After this, you need to disconnect the glass from the body. This can be done using a screwdriver or knife.

Removing sealant from taillights can also be done using a hair dryer

When removing the fog lamp, the battery should also be disconnected.

We will answer your questions for FREE regarding deprivation of rights, road accidents, insurance compensation, driving into the oncoming lane, etc. Daily from 9.00 to 21.00

Moscow and Moscow region

St. Petersburg and Leningrad region

Free call within Russia 8-800-350-23-69 ext.418

Video review of the procedure for replacing lamps in the rear combination lamp of Lada Priora (sedan, hatchback)

When purchasing a book in PDF

1. You will be able to download the book immediately after payment.

2. The book will be downloaded in PDF format, and you can download it to any device.

1. All books are of ideal quality, since we work with publishers directly.

2. Electronic books are in no way inferior to paper books and are their complete analogue.

3. Our company has offices in Ukraine, Russia and Poland, you can always contact us at a specific address.

4. All payments on the site are maximally protected and are made using global payment systems.

The book is not intended for sale in your country.

You can place an order for the paper version of this book on the website autoinform96.com.

Payment for goods and downloading of the book in electronic form (PDF format) is made on the website.

To do this, you need to find the book you are interested in and click on the “Buy” button. The price of the book is indicated on the button.

For convenience, the price on the website for residents of Russia, Belarus and Kazakhstan is presented in rubles.

For residents of Ukraine in hryvnias, and for all other countries - dollars.

After clicking on the “BUY” button, a payment window will open where you can select a payment system with which you can pay for the selected book using any bank card (Visa, MasterCard, MIR, etc.)

When you click on the “Pay by bank card” button, the Portmone payment system will open, which is the easiest way to make a payment.

In addition, the website offers four payment systems for payment:

• Yandex (payment from any bank cards, Yandex Money account, QIWI Wallet, terminals, etc.);
• Portmone (payment from any bank cards, Portmone account);
• PayPal (payment from any bank cards, PayPal account);
• WebMoney (payment from any bank cards, payment from WebMoney wallets).

The principle of operation of the headlight range control and options for its implementation

In its simplest form, the principle or description of the work will be as follows: the car has the ability to adjust the light directly from the interior. If the loading of the car has changed, for example, additional passengers have boarded, or the trunk is loaded, then the light will be shifted upward, which will lead to blinding oncoming drivers. To avoid this, it is possible to configure its direction, which allows you to move the light beam down or up to return normal lighting.

The described principle, which forms the basis of the corrector’s operation, is implemented using different methods. Today the adjustment could be:

forced action or automatic, in two versions, when used:

Forced adjustment

With this approach, the light flux is controlled manually, which is why a special switch is used in the car interior. Changing its position leads to a change in the position of the lighting fixtures.

Priora light control module

and Kalina.

Depending on the type of drive used in such a device, there are:

• electromechanical headlight range control;
• mechanical headlight range control;
• hydraulic;
• pneumatic, etc.

As an example of how any of the devices mentioned works, consider an electrical corrector

headlights It would be more correct to call it not electrical, but electromechanical. It includes:

1. position switch;
2. electric gear motor located on each headlight;
3. connecting wires.

The principle by which such a device works is quite simple. When the position of the switch in the car is changed, an electrical signal (voltage) is supplied to the gearmotor. Its rod, one end of which is located on the headlight reflector, moves. This movement of the rod leads to a change in the position of the associated reflector and, ultimately, in the luminous flux.

Automatic luminous flux correction

When an automatic headlight leveler is installed on a car, the driver does not need to do anything additional; in this case, the automation works for him.

It includes:

• device control unit;
• ride height sensors;
• actuators.

As already mentioned, its operation can occur in static and dynamic mode. In static mode, the automation controls the vehicle's ground clearance, and when it changes, due to additional loading of the vehicle, the control unit

sends an electrical signal to the actuators to adjust the position of the lighting fixtures.

However, this mode of operation, with the beginning of the use of xenon lamps, turned out to be insufficient. The luminous flux they generate

so powerful that even its short-term impact can blind oncoming drivers. Therefore, to prevent such a phenomenon, a dynamic corrector appeared.

Its main difference is speed. The operation of such a corrector is capable of changing the direction of the light flux in a fraction of a second. This allows you to keep the luminous flux within specified limits when accelerating the car, braking it, cornering and on uneven roads. Thanks to this, when adjusted correctly, even bright headlights do not blind oncoming drivers when making maneuvers.

Corrector

headlights have become an essential element of car design. Its use improves driving safety at night by ensuring constant illumination of the road surface and reducing the possibility of dazzling other drivers.

Payment via Yandex Cashier

After selecting payment via Yandex, the Yandex Cashier payment system will launch, where you need to select a convenient payment method (bank card, QIWI, Yandex Money account, etc.)

After specifying payment details and confirming payment, payment for the goods will occur.

If you have a bank card in a currency other than the ruble, then the money will be debited from the card at the rate of the Central Bank of Russia at the time of the purchase.

This payment method is optimal for residents of Russia, Kazakhstan and Belarus.

Official website of the Yandex Kassa payment system https://kassa.yandex.ru

Payment via Portmone

After selecting payment through Portmone, the payment system will launch, where you need to select the payment method: bank card or Portmone account.

The price in the Portmone payment system is converted into dollars at the exchange rate of the Central Bank of the country where you are located.

If you have a bank card in a currency other than the dollar, then the money will be debited from the card at the rate of the Central Bank of your country at the time of the purchase.

After specifying payment details and confirming payment, payment for the goods will occur.

Official website of the Portmone payment system https://www.portmone.com

Payment via PayPal

After selecting payment via PayPal, the PayPal payment system will launch, where you need to select the payment method: bank card or PayPal account.

If you already have a PayPal account, then you need to log into it and make a payment.

If you do not have a PayPal account and you want to pay using a bank card via PayPal, you need to click on the “Create an Account” button - shown with an arrow in the picture.

PayPal will then prompt you to select your country and provide your credit card information.

After specifying the information required to make the payment, you must click on the “Pay Now” button.

Official website of the PayPal payment system https://www.paypal.com

Payment via WebMoney

After selecting payment via WebMoney, the payment system will launch, where you need to select the payment method: bank card or WebMoney wallet.

If you already have a WebMoney wallet, then you need to log into it and make a payment.

If you do not have a WebMoney wallet and you want to pay in another way, you need to select any of the methods that WebMoney offers and make the payment

After specifying payment details and confirming payment, payment for the goods will occur.

Official website of the WebMoney payment system https://www.webmoney.ru/

Downloading a book

After successfully completing the payment (by any method) and returning to the KrutilVertel store from the payment system website, you will be taken to the successful payment page:

On this page you need to indicate your e-mail, where access to download the book will be sent.

If you are already registered on our website, then simply follow the link to your personal account.

The book you purchased will be in your personal account, from where you can always download it.

Please note that after making the payment, you need to return back from the payment system website to the KrutilVertel website.

If for some reason you did not return back to the site and closed the payment system tab with a message about the successful completion of the payment, please let us know - we will send you a letter indicating access to download the book.

Problems when paying with bank cards

Sometimes difficulties may arise when paying with Visa/MasterCard bank cards. The most common of them:

1. There is a restriction on the card for paying for online purchases
2. A plastic card is not intended for making payments online.
3. The plastic card is not activated for making payments online.
4. There are not enough funds on the plastic card.

In order to solve these problems, you need to call or write to the technical support of the bank where you are served. Bank specialists will help you resolve them and make payments.

That's basically it. The entire process of paying for a book in PDF format on car repair on our website takes 1-2 minutes.

Removing the rear light, replacing lamps on Lada Priora (VAZ-2170)

We carry out the work when replacing lamps in the rear light or replacing the light itself.

The work is shown on the left lantern.

To replace the lamps in the rear light, simply unscrew the nuts that secure it without disconnecting the light's wiring block from the rear wiring harness block. Inside the trunk...

...we bend the flap of the upholstery... ...and by hand unscrew the three fastenings of the flashlight (two nuts are located under the upholstery and are not visible in the photo).

Location of the rear light fastening nuts (shown with the light removed for clarity)

By turning the side light and brake light bulb socket counterclockwise...

...remove the lamp socket from the flashlight body. Pressing the lamp, turn it all the way counterclockwise...

...and remove the lamp from the socket.

The combination parking light and brake light have two protrusions located at different levels. When installing a new P21/4W parking light and brake light bulb, its protrusions must fit into the corresponding grooves in the socket.

We carry out the operations for replacing the remaining lamps in the same way.

Each lamp socket, in addition to the black “mass” wire, is connected to other wires of different colors.

In order not to confuse the lamp sockets when installing them, the corresponding wire colors are indicated on the lamp body.

For example, on the light housing next to the fog light lamp socket there is the inscription “red”, which corresponds to the red wire of the lamp socket. Next to the turn signal lamp socket there is the inscription “blue”, and next to the reversing light lamp socket it is written “green”. The exception is the socket for the side light and brake signal lamps, next to which there is no inscription.

To remove the rear light...

...squeeze the clamps of the rear wiring harness block... ...and disconnect it from the flashlight wiring block.

Using your hand, push the rubber sealing cover of the wires out from the hole in the body. Unscrew the three plastic nuts securing the rear light (see above).

We remove the lamp by pulling the wires with the block through the hole in the body. There are sealing gaskets installed on the three mounting threaded rods and two plastic mounting pins of the lantern.

If the gaskets are torn, replace them with new ones. Install the rear light in the reverse order.

Video on the topic “Lada Priora. Removing the rear light, replacing lamps"

Replacing rear light bulbs on a Priora

Lada Priora station wagon: replacing the tabs in the lamps How to remove the rear lamp and change all the lamps of the Lada Priora.

Replacing the brake light bulb of a Priora hatchback

1200 rub. for the photo report

We pay for photo reports on car repairs. Earnings from 10,000 rubles/month.

Write:

The light bulbs for the dimensions, brake light, reverse and turn signals in the Priora's taillight essentially change in the same way as on the Kalina, that is, to replace the bulbs you will first need to remove the taillight. To unscrew the headlights, you will need to partially bend the carpet (trunk lining) in order to get to the fastening bolts. It is not necessary to disconnect the light bulb connector because the length of the wires will be enough to set the flashlight a little to the side and unscrew the socket of the required light bulb. All bulbs in the taillight are replaced in the same way. To illustrate the process of removing the rear light of a Lada Priora hatchback and changing the brake, parking, reverse or turn signal lamps, watch the video.

We will show you how to replace the brake light, clearance and turn signal lamps in the rear lights of a Lada Priora Hatchback with your own hands. In essence, the light bulbs are changed in the same way as on the Lada Kalina; you first need to remove the entire headlamp and only then can you get to the light bulbs. With the trunk open, we need to unscrew at least one screw securing the trim and then disconnect the trim from the latch, pull out the latch and move the trim to the side to make it more convenient to continue working:

Or do this work through special technological holes in the carpet (with Velcro):

We choose the first method, it is much more convenient and everything is clearly visible. First, we’ll tell you how to remove the rear lights, two plastic screws are located in the photo at finger level, one is a little further away, you need to unscrew them immediately:

All this can be unscrewed by hand. When you unscrew the third one, it is advisable to hold the lantern so that it does not fall. After this, you can move the flashlight away and remove the light bulb we need. To do this, take it by the base and turn it counterclockwise. Insert the new light bulb all the way and turn it a little.

Video of replacing the brake signal lamp, dimensions, turn signal in the rear lights of the Lada Priora Hatchback:

Backup video instructions for replacing rear light bulbs in Lada Priora:

Replacing the brake light bulb, tail lights and turn signals on Priora Hatchback and Sedan

Video review of replacing light bulbs in the rear lights on a Lada Priora hatchback