How to choose the best lamp for low beam headlights on a Lada Largus

Driving safety largely depends on the condition of the head optics. Failure of any element impairs the driver's visibility of the roadway at night, increasing the risk of an emergency. The maximum load is experienced by the low beam lamp, which is the first to fail. Replacing a lamp requires skills, knowledge of the procedure and the availability of a spare light bulb that is suitable for all parameters. Let's look at the selection and installation procedure using the Lada Largus car as an example.

Lada Largus lamps

Lamps used on the Lada Largus passenger car:

• -Lamp for high and low beam headlights - H4 (AKG 12-60+55) 60/55 W;
• -Front direction indicator bulb - PY21W (A12-21-4) 21 W;
• - Side light electric lamp - W5W (A12-5-2) 5 W;
• -Electric fog lamp - H11 55 W;
• -Side turn signal lamp - WY5W 5 W;
• -The turn signal bulb in the rear light is PY21W (A12-21-4) 21 W;
• -Electric lamp for side light and tail light brake signal - P21/5W (A12-21+5) 21/5 W;
• -Electric fog light lamp in the rear light - P21W (A12-21-3) 21 W;
• - Rear light bulb for reversing light - P21W (A12-21-3) 21 W;
• -Rear additional brake light bulb - P21W (A12-21-3) 21 W;
• -Electric lamp for license plate lighting - W5W (A12-5-2) 5 W;
• -Trunk light bulb - W5W (A12-5-2) 5 W;
• -Interior lamp bulb - W5W (A12-5-2) 5 W;
• -Electric lamp for individual lighting - W5W (A12-5-2) 5 W;
• -Glove compartment lighting lamp - W5W (A12-5-2) 5 W;
• -Light bulb for lighting the cigarette lighter socket - W1.2W (A12-1.2) 1.2 W;
• -Electric lamp for illuminating the ventilation, heating and air conditioning control unit in the vehicle interior - W1.2W (A12-1.2) 1.2 W;
• -Hazard light switch illumination lamp - W1.2W (A12-1.2) 1.2 W;

Do-it-yourself replacement of lamps in Lada Largus

Any light bulb in this car can be replaced without a visit to the service center literally on the street. You don't even need a special tool for this. The only thing you may need is a flathead screwdriver to remove the lampshades.

Replacing lamps in the headlight of Lada Largus

To change the low beam and high beam bulbs, you must:

1. Remove the plastic cover.
2. Disconnect the electrical connector.
3. Remove the rubber boot of the lamp.
4. Disconnect the spring clip.
5. Pull out the lamp.
6. Install the new lamp and reassemble everything in reverse order.

After completing the replacement, it is recommended to adjust the cut-off line of the low beam headlights.

Replacing the turn signal lamp is carried out as follows:

1. Remove the electrical connector by lifting the latch.
2. Turn the socket clockwise or counterclockwise (depending on the headlamp) and remove it from the lamp housing.
3. Remove the lamp by pressing and turning it counterclockwise.
4. Reassemble in reverse order.

The marker lamp is easier to pull out - you just need to turn the lamp socket counterclockwise and remove the lamp from the socket by simply pulling it up.

Attention! Do not touch lamp bulbs with your hands, as grease on the surface of the glass will reduce its service life.

How to replace light sources in Largus taillights

To change the rear light bulbs on a Lada Largus, you need to remove the light from the car.

To do this, open the tailgate and unscrew the two plastic nuts securing the light. After which you can dismantle it and perform all the necessary manipulations:

1. Remove the electrical connector from the lamp.
2. Press out the three plastic latches securing the board with lamps.
3. To replace any of the lamps on the board, press it and turn it counterclockwise.
4. Install a new lamp and reassemble in reverse order.

Similar operations are performed for the lamp on the other side of the body.

Replacing fog lamps on Lada Largus

It is more convenient to replace it by unscrewing the front bumper from the corresponding fender liner.

To do this, you need to unscrew two T20 screws, and then unfasten the bumper from the latches. Next we perform the following operations:

1. We put our hand inside the bumper and unfasten the connector from the lamp.
2. Turn the lamp counterclockwise and pull it out of the PTF housing.
3. We install the new lamp in the reverse order and screw the fender liner to the bumper.

To make it easier to replace the light bulb, it is recommended to rotate the wheel for easier access.

How to change a side repeater lamp

Largus has turn signal repeaters mounted on the front fenders. You can do this by doing the following:

1. Using plastic or cardboard plates, we squeeze the repeater mounting clamps on both sides.
2. Remove it from the wing.
3. Turn the cartridge counterclockwise and remove it from the housing.
4. Pull the lamp up and remove it from the socket.
5. Install the new lamp in the reverse order of removal and reassemble.

There is another replacement method. To release the repeater housing clamps, you need to remove the fender liner. However, this method is not very convenient.

Replacement of license plate lamps in Largus

There is nothing difficult about replacing this light source. Just take a T20 Torx and unscrew the screw securing the diffuser.

Next, you just need to pull it out and replace the lamp inside the bumper by pulling it out of the socket. Install a new one in its place and screw the diffuser back.

How to change interior lamps in Largus

The interior of this car only supports the following lights:

• trunk;
• glove box;
• lampshade;
• heater control unit.

To remove the interior light bulb, use a flat-head screwdriver to remove the lamp diffuser, then remove the required bulb and install a new one.

The trunk has exactly the same lamp, and therefore the replacement of light sources occurs in exactly the same way.

In the glove compartment, simply pry up the lampshade using a screwdriver. It will fall out and the lamp can be replaced by removing it from the socket.

Replacing the lamp in the heater control unit is carried out as follows:

1. Using a plastic puller, unfasten the center console trim.
2. Place your hand inside the panel and feel the base on the back of the block.
3. Rotate the desired base 45 degrees and pull it out.
4. Replace the lamp on it and reassemble in the reverse order.

This completes the replacement of interior lamps.

Headlight bulbs

Low and high beam headlight lamp

Light bulb type:

Designation of high and low beam headlight bulbs according to EEC - H4

Technical characteristics of Llama H4 high and low beam headlights:

• Power - 60/55 W;
• Light - xenon;
• The base is metal;
• The base is round;
• The color of the flask is transparent;

Dimensions of the H4 lamp for low and high beam headlights Lada Largus

1. The diameter of the flask is 17 mm;
2. The size from the tip of the flask to the seat is 60 mm;
3. Lamp height - 92 mm;
4. Base diameter - 43 mm;
5. Base height - 32 mm;

The installation location of the H4 lamp for high and low beam headlights is shown in the figure below:

The car has two such H4 bulbs.

Front turn signal lamp Lada Largus

Design of the front turn signal lamp in the headlight unit:

ECE light bulb designation: PY21W

Technical characteristics of the front turn signal lamp:

• Lamp - incandescent;
• Power - 21 W;
• The color of the flask is red;
• The base is metal;
• The base is round.

Dimensions of the PY21W turn signal lamp in the headlight of Lada Largus

1. The diameter of the flask is 26×5 mm;
2. Lamp height - 52.5 mm;
3. Base diameter - 17 mm;

The installation location of the PY21W front turn signal lamp for Lada Largus is shown in the figure below:

Side light unit light bulb

Design of the W5W side light lamp in the headlight unit:

ECE light bulb designation: W5W

Technical characteristics of the side light lamp in the headlight unit:

• Lamp - incandescent;
• Power - 5 W;
• The color of the flask is transparent;
• Base - glass;

Dimensions of the W5W side light bulb for the Lada Largus headlights

1. The diameter of the flask is 10.3 mm;
2. The size from the tip of the flask to the seat is 20.7 mm;
3. Lamp height - 26.8 mm;
4. Base diameter - 9.5 mm;
5. Base height - 6.1 mm;

The installation location of the W5W lamp for the side light headlight block of the Lada Largus is shown in the figure below:

Main conclusions

Replacing low beam lamps on the Lada Largus is carried out according to the usual method for most cars. No special preliminary steps are required other than temporarily removing the battery that prevents access to the left headlight. When choosing a replacement lamp, you should carefully study its parameters and select models with the most successful characteristics for a given region or operating conditions. The best option would be models produced by well-known companies; the pursuit of a low price will not live up to expectations and may result in unnecessary expenses.

Previous

Car light LED lamps for cars: characteristics, types, review of manufacturers and selection tips

Next

Car lightReplacing low beam lamps on Lada Granda

Largus fog lamp

H11 Fog Light Bulb Design:

EEC light bulb designation: H11

Technical characteristics of the H11 fog lamp lamp:

• Lamp - halogen;
• Power - 55 W;
• The flask is transparent;
• The base is plastic;
• The base is an individual design;

Dimensions of the H11 lamp for the fog lamp of the Lada Largus

1. The diameter of the flask is 11 mm;
2. The size from the tip of the flask to the seat is 43 mm;

The installation location of the H11 lamp for the Lada Largus fog light is shown in the figure below:

High beam headlight

The lamp is not accessible from the engine compartment, so replace the lower part.

1. Remove the wheel arch trim by unscrewing the screws;
2. Remove the lamp cartridge by turning it clockwise (right. counterclockwise);
3. Remove the cartridge from the cartridge without the lamp.

remove the wheel arch trim Lada Largus Lada Largus replacement light bulb Lada Largus replacement light bulb

Install the new lamp in reverse order.

Side turn signal lamp

Design of WY5W red side turn signal lamp:

EEC light bulb designation - WY5W

Specifications of WY5W side turn signal lamp:

• Lamp - Incandescent;
• Power - 5 W;
• Color - red;
• Base - glass;
• The base is flat.

Dimensions of the WY5W side turn signal lamp for Lada Largus

1. The diameter of the flask is 10.3 mm;
2. The size from the tip of the flask to the seat is 20.7 mm;
3. Base width - 9.5 mm;
4. Base thickness - 2.1 mm;
5. Lamp height - 26.8 mm;

The installation location of the WY5W side turn signal lamp for the Lada Largus is shown in the figure below:

The best LED lamps in Largus

We recommend LEDs from time-tested manufacturers. For example, from Philips. One of the oldest Dutch brands, operating for more than 120 years.

For Largus owners we recommend:

The price of LEDs is compensated by their service life and comfort. Thanks to the high light temperature, the lamps imitate natural light - this reduces eye strain, and the picture is not distorted. The increased working life makes LED more profitable than incandescent lamps, if we estimate the period from 5-6 years.

Source

Tail light bulbs

Turn signal lamp in rear light

Design of the PY21W turn signal lamp in the red rear light:

ECE light bulb designation - PY21W

Technical characteristics of the PY21W turn signal lamp in the rear light:

• Lamp - incandescent;
• Power - 21 W;
• Color - red;
• The base is metal;
• The base is round.

Dimensions of the PY21W turn signal lamp in the rear light of Lada Largus

1. The diameter of the flask is 10.3 mm;
2. The size from the tip of the flask to the seat is 20.7 mm;
3. Base width - 9.5 mm;
4. Base thickness - 2.1 mm;
5. Lamp height - 26.8 mm;

Installation location of the PY21W turn signal lamp in the rear light of Lada Largus:

Electric lamp of dimensions and brake signal Largus

Design of the P21/5W lamp of the dimensions and brake light of the rear light:

EEC light bulb designation - P21/5W

Technical characteristics of the P21/5W lamp of dimensions and brake light in the rear light:

• Lamp - incandescent;
• Power - 21/5 W;
• The color of the flask is transparent;
• Filaments - 2 pcs;
• The base is metal;
• The base is round.

Dimensions of the P21/5W stop lamp and dimensions in the rear light of the Lada Largus

1. The diameter of the flask is 26.5 mm;
2. The size from the tip of the flask to the seat is 45 mm;
3. Lamp height - 52.5 mm;

Installation location of the P21/5W lamp for the dimensions and brake light in the rear light of the Lada Largus:

Tail light fog lamp

P21W Tail Fog Light Bulb Design:

Lamp designation according to ECE - P21W

Specifications of P21W tail light fog light bulb:

• Lamp - incandescent;
• Power - 21 W;
• The color of the flask is transparent;
• The base is metal;
• Filament - 1 pc.

Dimensions of the P21W fog light lamp in the rear light of Lada Largus

1. The diameter of the flask is 26.5 mm;
2. The size from the tip of the flask to the seat is 45 mm;
3. Lamp height - 52.5 mm;

Installation location of the P21W fog light lamp in the rear light of the Lada Largus:

Reversing light bulb

Design of P21W tail light reversing light bulb:

Lamp designation according to ECE - P21W

Technical characteristics of P21W rear light bulb:

• Power - 21 W;
• Color: transparent;
• The base is metal;
• Filament - 1 pc.

Dimensions of the P21W reverse lamp in the rear light of Lada Largus

1. The diameter of the flask is 26.5 mm;
2. The size from the tip of the flask to the seat is 45 mm;
3. Lamp height - 52.5 mm;

Installation location of the P21W reversing light lamp in the rear right lamp of the Lada Largus:

Replacing light bulbs in dimensions

The other day I thought of something - I don’t pay any attention to Largus at all - he stands under the windows, his wife walks him as needed very rarely, on weekends, however, we ride him to the village in the bathhouse to warm up.
Compared to him, Shniva plows “like Papa Carlo.” And then there was a payday and a car store on the way to the house. I bought proven Mayak diode bulbs, sealed in wormlight, and white caps for stamped size 15 discs,

Well, in fact, I implemented these devices that same evening by the light of a flashlight and a headlamp.

And a general view of two cars with the same dimensions

There’s no way I’ll strangle the “green amphibian” to order a set of door sills and a third row of seats from the Largus shop, but oh well - a little of the good stuff, otherwise you’ll stop enjoying the little things. All the best to everyone!

Additional brake light lamp Largus

Design of lamp P21W additional brake light:

Lamp designation according to ECE - P21W

Technical characteristics of the P21W additional brake light lamp:

• Power - 21 W;
• Color: transparent;
• The base is metal;
• The base is round.

Dimensions of the P21W additional brake light lamp for Lada Largus

1. The diameter of the flask is 26.5 mm;
2. The size from the tip of the flask to the seat is 45 mm;
3. Lamp height - 52.5 mm;

Installation location of the P21W additional brake light lamp for Lada Largus:

How to replace

After choosing a light bulb model for Largus, new components are purchased.

It is not recommended to use used cartridges and fuses: during long-term storage, electrical wiring contacts, terminals and adjacent components oxidize.

Required components to replace the front low beam lamp:

• car lamps;
• circuit breakers;
• cartridge;
• tools (screwdriver, pliers, etc.).

To begin with, the car's electrical network is disconnected from the power supply (battery), then the burnt-out part is removed.

Electric license plate lamp

W5W license plate lamp design:

Lamp designation according to ECE - W5W

Technical characteristics of the license plate lamp W5W:

• Power - 5 W;
• Color: transparent;
• Base - glass;
• The base is flat.

Dimensions of the W5W lamp for the license plate light of the Lada Largus

1. The diameter of the flask is 10.3 mm;
2. The size from the tip of the flask to the seat is 20.7 mm;
3. Lamp height - 26.8 mm;
4. Base width - 9.5 mm;
5. Base thickness - 2.1 mm;

Installation location of the W5W lamp for the Lada Largus license plate light:

Standard replacement procedure

1. Replacing the low beam lamp, as well as the high beam, begins by disconnecting the on-board power supply. This precedes all electrical repair work. In this case, a special switch is turned or the negative terminal is disconnected from the battery, which avoids accidental short circuits or erroneous connections during installation.
2. The place where the Largus lamp will be replaced is determined. There, the rubber plugs covering the electrical components are removed, and two metal antennae are opened in front of the car owner, fixing them in the reflector. They are separated so that the used parts can come out of their seat without damaging the housing.
3. Next, you need to disconnect the plugs from the wiring that was previously disconnected. Here it is worth paying attention to the order of arrangement, otherwise, during the installation of new parts, everything can be mixed up and they will have to be changed again.
4. After connecting the plug with wiring to the new parts, they are mounted in place and secured with antennae. You should try not to touch the flasks with your hands, as this can lead to their rapid failure.
5. If the light is dim during lighting, and the headlights flash when you turn on the headlights, then it is imperative to restore the contacts of the wires with the vehicle body. This is especially true for a marker lamp, because the fat that gets there begins to evaporate when heated and can cause ignition.
6. At the end of this procedure, you need to put on the rubber plugs and secure all the parts in their places. After this, the car will be ready for use and the driver does not have to worry about malfunctions of the Lada Largus lighting fixtures.

As practice shows, in modern domestic cars, one of which is the Lada Largus, lamps with directional luminous flux are most often used. The essence of such lighting is a reliable view in front of and behind the car. At the same time, inconvenience to other traffic participants heading towards the driver or driving behind is excluded.

Trunk light for Lada Largus

Design of the W5W trunk light bulb:

Lamp designation according to ECE - W5W

Technical characteristics of the W5W trunk lighting lamp:

• Power - 5 W;
• Color: transparent;
• Base - glass;
• The base is flat.

Dimensions of the W5W lamp for lighting the trunk of the Lada Largus

1. The diameter of the flask is 10.3 mm;
2. The size from the tip of the flask to the seat is 20.7 mm;
3. Lamp height - 26.8 mm;
4. Base width - 9.5 mm;
5. Base thickness - 2.1 mm;

Installation location of the W5W lamp for lighting the trunk of the Lada Largus:

Daylight

If the optics on the Lada Largus are faulty, replacing the light bulb will require the following algorithm:

1. The rubber pad is removed, which serves as protection for the electrical unit.
2. The block with the installed wires is removed.
3. The U-shaped lock moves (moving to the side and back).
4. The electric lamp is pulled out.
5. The detail changes.

It is important to remember the orientation of the cartridge - two teeth at the top, one at the bottom.

How to replace a Largus lamp:

1. When installing, hold the lamp by the base or use microfiber, otherwise marks will remain on the electrical appliance and it will burn out faster;
2. Repeat all the above steps to remove the optics in reverse order.

It is recommended to replace both bulbs at the same time. This will prevent unexpected overheating of the remaining part and ensure the same light beam parameter.

Interior light bulb

Design of the W5W lamp for the interior lighting:

Lamp designation according to ECE - W5W

Technical characteristics of the W5W lamp for the interior lighting:

• Power - 5 W;
• Color: transparent;
• Base - glass;
• The base is flat.

Dimensions of the W5W lamp for the interior lighting of the Lada Largus

1. The diameter of the flask is 10.3 mm;
2. The size from the tip of the flask to the seat is 20.7 mm;
3. Lamp height - 26.8 mm;
4. Base width - 9.5 mm;
5. Base thickness - 2.1 mm;

Installation location of the W5W lamp for the interior lighting of the Lada Largus:

Choice

First of all, it should be said that the low beam lamp for the Lada Largus uses a halogen H4 standard, i.e. contains two threads and is responsible not only for near, but also for distant lighting.

Currently on the market you can find such lamps from a variety of manufacturers, among which are the following:

• Bosh;
• Osram;
• Philips;
• Narva, etc.

In addition, domestic Mayak light bulbs have recently proven themselves to be quite good. Their advantages include not only low price, but good quality.

H4 standard lamp

Advice! It is advisable to purchase light bulbs in specialized stores, since recently a lot of counterfeit products from China have appeared that quickly fail or produce poor-quality light.

Of course, when choosing lamps you need to pay attention not only to the brand, but also to the following characteristics of the lighting element:

Standard halogens provide an unnatural yellowish glow. However, recently light bulbs have appeared with a bluish glow. People call them pseudo-xenon.

However, it should be noted that such light illuminates the road well only in dry weather. In fog or rain, ordinary lamps are preferable.

Moreover, in bad weather, even the expensive “xenon” and “LEDs” are inferior to the latter, the power of the light beam is one and a half to two times more powerful than that of halogen bulbs. This is due to the fact that the light of these elements has insufficient penetrating power.

Note! To install xenon and halogen lamps, you should contact a service center for help, since this work requires the installation of additional equipment and changes to the software. Accordingly, the installation of such lighting is quite expensive.

Lamp for individual lighting of Lada Largus

Design of the W5W lamp for individual lighting:

Lamp designation according to ECE - W5W

Technical characteristics of the W5W lamp for individual lighting:

• Power - 5 W;
• Color: transparent;
• Base - glass;
• The base is flat.

Dimensions of the W5W lamp for the individual lighting of the Lada Largus

1. The diameter of the flask is 10.3 mm;
2. The size from the tip of the flask to the seat is 20.7 mm;
3. Lamp height - 26.8 mm;
4. Base width - 9.5 mm;
5. Base thickness - 2.1 mm;

Installation location of the W5W lamp for the individual lighting of the Lada Largus:

Troubleshooting Some Problems

If, after replacing the lamp, the low beam on the Lada Largus still does not light up, the cause of the malfunction may be a blown fuse. Replacing them is even easier than the paws, since they are located in the cabin, on the left side of the steering column.

Two fuses are responsible for the low beam:

• F9 – left headlight.
• F10 – right headlight.

Note! Even if the fuse is not visually damaged, a new one should be installed in its place.

Fuse box diagram
Often the cause of a malfunction is poor contacts of the fuse terminals. In this case, you just need to clean them.

It should be noted that there is no low beam relay on the Lada Largus, therefore, if replacing the fuses did not produce results, all that remains is to check the contacts in the headlight itself, which could have burned out or oxidized.

Often the light goes out due to poor contact of the machine ground wire. In this case, the problem is also solved by thoroughly cleaning the contact. If it was not possible to restore the light, you need to contact a service center for help.

Here, perhaps, are all the instructions for correcting the most common VAZ wiring faults.

Electrical lamps of the instrument panel

Glove box light bulb

Design of the W5W glove box light bulb:

Lamp designation according to ECE - W5W

Technical characteristics of the W5W lamp for the glove compartment light:

• Power - 5 W;
• Color: transparent;
• Base - glass;
• The base is flat.

Dimensions of the W5W lamp for the glove compartment lighting of the Lada Largus

1. The diameter of the flask is 10.3 mm;
2. The size from the tip of the flask to the seat is 20.7 mm;
3. Lamp height - 26.8 mm;
4. Base width - 9.5 mm;
5. Base thickness - 2.1 mm;

Installation location of the W5W lamp for the glove box lighting of the Lada Largus:

Cigarette lighter lamp for Lada Largus

Design of W1.2W cigarette lighter lamp:

Lamp designation according to ECE - W1.2W

Technical characteristics of the W1.2W cigarette lighter lamp:

• Power - 1.2 W;
• Color: transparent;
• Base - glass;
• The base is flat.

Dimensions of the W1.2W cigarette lighter lamp for Lada Largus

1. The diameter of the flask is 5 mm;
2. The size from the tip of the flask to the seat is 14.5 mm;
3. Lamp height - 20 mm;
4. Base width - 5 mm;

Installation location of the W1.2W lamp for the cigarette lighter illumination of the Lada Largus:

Electric lamps for illumination of the ventilation, heating and air conditioning control unit

Design of the W1.2W lamp for illuminating the ventilation, heating and air conditioning control unit:

Lamp designation according to ECE - W1.2W

Technical characteristics of the W1.2W lamp for the ventilation, heating and air conditioning control unit:

• Power - 1.2 W;
• Color: transparent;
• Base - glass;
• The base is flat.

Dimensions of the W1.2W lamp of the control unit for ventilation, heating and air conditioning Lada Largus

1. The diameter of the flask is 5 mm;
2. The size from the tip of the flask to the seat is 14.5 mm;
3. Lamp height - 20 mm;
4. Base width - 5 mm;

Installation location of the W1.2W lamp for the control unit for ventilation, heating and air conditioning Lada Largus:

How to change the low/high beam lamps on Largus, as well as the dimensions

A note about what kind of lighting lamps are installed in the Largus headlights;
which of them are low/high beam, and which are responsible for the side lights. How to change lamps yourself. How much do originals and analogues cost in Yaroslavl Good day, future and aspiring gentlemen Largusovod!

On Largus, the low/high beam and headlight lamps often burn out. At least for 70 thousand I have already changed it five times on each side.

The following light bulbs were installed on my car:

1. Low/high beam: halogen, Osram H4 12v 60/55w. (art. 64193). Price from 109 rub.

There are many analogues. Here are some of them:

370 rub. General Electric (34454)

117 rub. Valeo (032007)

2. Front dimensions: halogen baseless 12V Osram (art. 2825). Price from 17 rub.

26 rub. Lynx (L12805)

9 rub. Fortluft (2825)

3. Rear dimensions: two-pin with filament, base BAY15D. Beacon 12V P21/5W.

from 56 rub. Fortluft (7528)

They burn out less often. I changed it only once in the right headlight. This is what she looks like:

How to replace headlight bulbs

1. First, remove the protective cover. It turns a little, then a small latch is released.

2. The block with wires is removed.

3. Remove the rubber protective sleeve.

4. The lamp is pressed U -shaped clamp. It needs to be pulled to the side and back.

5. Take out the lamp. Remember its orientation. Two teeth at the bottom, one at the top. And if you look at it from the side of the headlight, the inscription (marking) will be on top.

6. Install a new lamp. You should not take it with your bare hands, as greasy marks from the pores will remain on the bulb and the lamp will fail faster. This applies to all halogen lamps. It is better to hold it by the plinth or use a microfiber cloth.

7. Assembly is carried out in reverse order. First the clamping clamp, then the rubber bushing and finally the top cover.

How to replace front markers

There isn't much action here. The main thing is to get to the cartridge and turn it 90 degrees. On the left headlight it is clockwise, on the right it is counterclockwise. The most inconvenient thing to change is the battery side. Not enough space. If your hand is large, it is better to remove it.

If you can’t feel the cartridge at all, then the operating instructions advise removing the fender liner.

The procedure is as follows:

• Found a cartridge
• They turned it over and took it out
• Removed the lamp
• It is better to wear gloves when installing a new lamp into the socket.
• Then the cartridge was installed back into the headlight and rotated 90 degrees.

How to replace rear lights

Changing lamps is a pleasure. All you need to do is remove the headlight unit. It is secured with two wings from the interior: one at the top under the plastic upholstery, the other at the bottom. We unscrew them, move the headlight to the side and disconnect the block with the wires.

Next you need to remove the protective cover. It is held on by three latches. There are three lamps underneath it. We find the size lamp and change it. The steps are simple: insert into the cartridge and turn.